Merge remote-tracking branch 'input/next'

6 files changed, 360 insertions, 36 deletions

diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c
index eb3006361ee4..6e6145b9a4c1 100644
--- a/drivers/input/keyboard/gpio_keys.c
+++ b/drivers/input/keyboard/gpio_keys.c
@@ -324,7 +324,12 @@ static void gpio_keys_report_event(struct gpio_button_data *bdata)
 	unsigned int type = button->type ?: EV_KEY;
 	int state = (gpio_get_value_cansleep(button->gpio) ? 1 : 0) ^ button->active_low;
 
-	input_event(input, type, button->code, !!state);
+	if (type == EV_ABS) {
+		if (state)
+			input_event(input, type, button->code, button->value);
+	} else {
+		input_event(input, type, button->code, !!state);
+	}
 	input_sync(input);
 }
 
@@ -363,7 +368,7 @@ static int __devinit gpio_keys_setup_key(struct platform_device *pdev,
 					 struct gpio_button_data *bdata,
 					 struct gpio_keys_button *button)
 {
-	char *desc = button->desc ? button->desc : "gpio_keys";
+	const char *desc = button->desc ? button->desc : "gpio_keys";
 	struct device *dev = &pdev->dev;
 	unsigned long irqflags;
 	int irq, error;
@@ -468,7 +473,7 @@ static int __devinit gpio_keys_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, ddata);
 	input_set_drvdata(input, ddata);
 
-	input->name = pdev->name;
+	input->name = pdata->name ? : pdev->name;
 	input->phys = "gpio-keys/input0";
 	input->dev.parent = &pdev->dev;
 	input->open = gpio_keys_open;
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 434fd800cd24..cabd9e54863f 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -248,6 +248,18 @@ config TOUCHSCREEN_LPC32XX
 	  To compile this driver as a module, choose M here: the
 	  module will be called lpc32xx_ts.
 
+config TOUCHSCREEN_MAX11801
+	tristate "MAX11801 based touchscreens"
+	depends on I2C
+	help
+	  Say Y here if you have a MAX11801 based touchscreen
+	  controller.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called max11801_ts.
+
 config TOUCHSCREEN_MCS5000
 	tristate "MELFAS MCS-5000 touchscreen"
 	depends on I2C
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index ca94098d4c92..282d6f76ae26 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_INEXIO)	+= inexio.o
 obj-$(CONFIG_TOUCHSCREEN_INTEL_MID)	+= intel-mid-touch.o
 obj-$(CONFIG_TOUCHSCREEN_LPC32XX)	+= lpc32xx_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MAX11801)	+= max11801_ts.o
 obj-$(CONFIG_TOUCHSCREEN_MC13783)	+= mc13783_ts.o
 obj-$(CONFIG_TOUCHSCREEN_MCS5000)	+= mcs5000_ts.o
 obj-$(CONFIG_TOUCHSCREEN_MIGOR)		+= migor_ts.o
diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c
index 4012436633b1..1e61387c73ca 100644
--- a/drivers/input/touchscreen/atmel_mxt_ts.c
+++ b/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -17,7 +17,7 @@
 #include <linux/firmware.h>
 #include <linux/i2c.h>
 #include <linux/i2c/atmel_mxt_ts.h>
-#include <linux/input.h>
+#include <linux/input/mt.h>
 #include <linux/interrupt.h>
 #include <linux/slab.h>
 
@@ -196,9 +196,12 @@
 #define MXT_PRESS		(1 << 6)
 #define MXT_DETECT		(1 << 7)
 
+/* Touch orient bits */
+#define MXT_XY_SWITCH		(1 << 0)
+#define MXT_X_INVERT		(1 << 1)
+#define MXT_Y_INVERT		(1 << 2)
+
 /* Touchscreen absolute values */
-#define MXT_MAX_XC		0x3ff
-#define MXT_MAX_YC		0x3ff
 #define MXT_MAX_AREA		0xff
 
 #define MXT_MAX_FINGER		10
@@ -246,6 +249,8 @@ struct mxt_data {
 	struct mxt_info info;
 	struct mxt_finger finger[MXT_MAX_FINGER];
 	unsigned int irq;
+	unsigned int max_x;
+	unsigned int max_y;
 };
 
 static bool mxt_object_readable(unsigned int type)
@@ -499,19 +504,21 @@ static void mxt_input_report(struct mxt_data *data, int single_id)
 		if (!finger[id].status)
 			continue;
 
-		input_report_abs(input_dev, ABS_MT_TOUCH_MAJOR,
-				finger[id].status != MXT_RELEASE ?
-				finger[id].area : 0);
-		input_report_abs(input_dev, ABS_MT_POSITION_X,
-				finger[id].x);
-		input_report_abs(input_dev, ABS_MT_POSITION_Y,
-				finger[id].y);
-		input_mt_sync(input_dev);
+		input_mt_slot(input_dev, id);
+		input_mt_report_slot_state(input_dev, MT_TOOL_FINGER,
+				finger[id].status != MXT_RELEASE);
 
-		if (finger[id].status == MXT_RELEASE)
-			finger[id].status = 0;
-		else
+		if (finger[id].status != MXT_RELEASE) {
 			finger_num++;
+			input_report_abs(input_dev, ABS_MT_TOUCH_MAJOR,
+					finger[id].area);
+			input_report_abs(input_dev, ABS_MT_POSITION_X,
+					finger[id].x);
+			input_report_abs(input_dev, ABS_MT_POSITION_Y,
+					finger[id].y);
+		} else {
+			finger[id].status = 0;
+		}
 	}
 
 	input_report_key(input_dev, BTN_TOUCH, finger_num > 0);
@@ -549,8 +556,13 @@ static void mxt_input_touchevent(struct mxt_data *data,
 	if (!(status & (MXT_PRESS | MXT_MOVE)))
 		return;
 
-	x = (message->message[1] << 2) | ((message->message[3] & ~0x3f) >> 6);
-	y = (message->message[2] << 2) | ((message->message[3] & ~0xf3) >> 2);
+	x = (message->message[1] << 4) | ((message->message[3] >> 4) & 0xf);
+	y = (message->message[2] << 4) | ((message->message[3] & 0xf));
+	if (data->max_x < 1024)
+		x = x >> 2;
+	if (data->max_y < 1024)
+		y = y >> 2;
+
 	area = message->message[4];
 
 	dev_dbg(dev, "[%d] %s x: %d, y: %d, area: %d\n", id,
@@ -804,10 +816,6 @@ static int mxt_initialize(struct mxt_data *data)
 	if (error)
 		return error;
 
-	error = mxt_make_highchg(data);
-	if (error)
-		return error;
-
 	mxt_handle_pdata(data);
 
 	/* Backup to memory */
@@ -845,6 +853,20 @@ static int mxt_initialize(struct mxt_data *data)
 	return 0;
 }
 
+static void mxt_calc_resolution(struct mxt_data *data)
+{
+	unsigned int max_x = data->pdata->x_size - 1;
+	unsigned int max_y = data->pdata->y_size - 1;
+
+	if (data->pdata->orient & MXT_XY_SWITCH) {
+		data->max_x = max_y;
+		data->max_y = max_x;
+	} else {
+		data->max_x = max_x;
+		data->max_y = max_y;
+	}
+}
+
 static ssize_t mxt_object_show(struct device *dev,
 				    struct device_attribute *attr, char *buf)
 {
@@ -981,6 +1003,10 @@ static ssize_t mxt_update_fw_store(struct device *dev,
 
 	enable_irq(data->irq);
 
+	error = mxt_make_highchg(data);
+	if (error)
+		return error;
+
 	return count;
 }
 
@@ -1052,31 +1078,33 @@ static int __devinit mxt_probe(struct i2c_client *client,
 	input_dev->open = mxt_input_open;
 	input_dev->close = mxt_input_close;
 
+	data->client = client;
+	data->input_dev = input_dev;
+	data->pdata = pdata;
+	data->irq = client->irq;
+
+	mxt_calc_resolution(data);
+
 	__set_bit(EV_ABS, input_dev->evbit);
 	__set_bit(EV_KEY, input_dev->evbit);
 	__set_bit(BTN_TOUCH, input_dev->keybit);
 
 	/* For single touch */
 	input_set_abs_params(input_dev, ABS_X,
-			     0, MXT_MAX_XC, 0, 0);
+			     0, data->max_x, 0, 0);
 	input_set_abs_params(input_dev, ABS_Y,
-			     0, MXT_MAX_YC, 0, 0);
+			     0, data->max_y, 0, 0);
 
 	/* For multi touch */
+	input_mt_init_slots(input_dev, MXT_MAX_FINGER);
 	input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR,
 			     0, MXT_MAX_AREA, 0, 0);
 	input_set_abs_params(input_dev, ABS_MT_POSITION_X,
-			     0, MXT_MAX_XC, 0, 0);
+			     0, data->max_x, 0, 0);
 	input_set_abs_params(input_dev, ABS_MT_POSITION_Y,
-			     0, MXT_MAX_YC, 0, 0);
+			     0, data->max_y, 0, 0);
 
 	input_set_drvdata(input_dev, data);
-
-	data->client = client;
-	data->input_dev = input_dev;
-	data->pdata = pdata;
-	data->irq = client->irq;
-
 	i2c_set_clientdata(client, data);
 
 	error = mxt_initialize(data);
@@ -1090,6 +1118,10 @@ static int __devinit mxt_probe(struct i2c_client *client,
 		goto err_free_object;
 	}
 
+	error = mxt_make_highchg(data);
+	if (error)
+		goto err_free_irq;
+
 	error = input_register_device(input_dev);
 	if (error)
 		goto err_free_irq;
diff --git a/drivers/input/touchscreen/max11801_ts.c b/drivers/input/touchscreen/max11801_ts.c
new file mode 100644
index 000000000000..4f2713d92791
--- /dev/null
+++ b/drivers/input/touchscreen/max11801_ts.c
@@ -0,0 +1,272 @@
+/*
+ * Driver for MAXI MAX11801 - A Resistive touch screen controller with
+ * i2c interface
+ *
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Author: Zhang Jiejing <jiejing.zhang@freescale.com>
+ *
+ * Based on mcs5000_ts.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+
+/*
+ * This driver aims to support the series of MAXI touch chips max11801
+ * through max11803. The main difference between these 4 chips can be
+ * found in the table below:
+ * -----------------------------------------------------
+ * | CHIP     |  AUTO MODE SUPPORT(FIFO) | INTERFACE    |
+ * |----------------------------------------------------|
+ * | max11800 |  YES                     |   SPI        |
+ * | max11801 |  YES                     |   I2C        |
+ * | max11802 |  NO                      |   SPI        |
+ * | max11803 |  NO                      |   I2C        |
+ * ------------------------------------------------------
+ *
+ * Currently, this driver only supports max11801.
+ *
+ * Data Sheet:
+ * http://www.maxim-ic.com/datasheet/index.mvp/id/5943
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+#include <linux/bitops.h>
+
+/* Register Address define */
+#define GENERNAL_STATUS_REG		0x00
+#define GENERNAL_CONF_REG		0x01
+#define MESURE_RES_CONF_REG		0x02
+#define MESURE_AVER_CONF_REG		0x03
+#define ADC_SAMPLE_TIME_CONF_REG	0x04
+#define PANEL_SETUPTIME_CONF_REG	0x05
+#define DELAY_CONVERSION_CONF_REG	0x06
+#define TOUCH_DETECT_PULLUP_CONF_REG	0x07
+#define AUTO_MODE_TIME_CONF_REG		0x08 /* only for max11800/max11801 */
+#define APERTURE_CONF_REG		0x09 /* only for max11800/max11801 */
+#define AUX_MESURE_CONF_REG		0x0a
+#define OP_MODE_CONF_REG		0x0b
+
+/* FIFO is found only in max11800 and max11801 */
+#define FIFO_RD_CMD			(0x50 << 1)
+#define MAX11801_FIFO_INT		(1 << 2)
+#define MAX11801_FIFO_OVERFLOW		(1 << 3)
+
+#define XY_BUFSIZE			4
+#define XY_BUF_OFFSET			4
+
+#define MAX11801_MAX_X			0xfff
+#define MAX11801_MAX_Y			0xfff
+
+#define MEASURE_TAG_OFFSET		2
+#define MEASURE_TAG_MASK		(3 << MEASURE_TAG_OFFSET)
+#define EVENT_TAG_OFFSET		0
+#define EVENT_TAG_MASK			(3 << EVENT_TAG_OFFSET)
+#define MEASURE_X_TAG			(0 << MEASURE_TAG_OFFSET)
+#define MEASURE_Y_TAG			(1 << MEASURE_TAG_OFFSET)
+
+/* These are the state of touch event state machine */
+enum {
+	EVENT_INIT,
+	EVENT_MIDDLE,
+	EVENT_RELEASE,
+	EVENT_FIFO_END
+};
+
+struct max11801_data {
+	struct i2c_client		*client;
+	struct input_dev		*input_dev;
+};
+
+static u8 read_register(struct i2c_client *client, int addr)
+{
+	/* XXX: The chip ignores LSB of register address */
+	return i2c_smbus_read_byte_data(client, addr << 1);
+}
+
+static int max11801_write_reg(struct i2c_client *client, int addr, int data)
+{
+	/* XXX: The chip ignores LSB of register address */
+	return i2c_smbus_write_byte_data(client, addr << 1, data);
+}
+
+static irqreturn_t max11801_ts_interrupt(int irq, void *dev_id)
+{
+	struct max11801_data *data = dev_id;
+	struct i2c_client *client = data->client;
+	int status, i, ret;
+	u8 buf[XY_BUFSIZE];
+	int x = -1;
+	int y = -1;
+
+	status = read_register(data->client, GENERNAL_STATUS_REG);
+
+	if (status & (MAX11801_FIFO_INT | MAX11801_FIFO_OVERFLOW)) {
+		status = read_register(data->client, GENERNAL_STATUS_REG);
+
+		ret = i2c_smbus_read_i2c_block_data(client, FIFO_RD_CMD,
+						    XY_BUFSIZE, buf);
+
+		/*
+		 * We should get 4 bytes buffer that contains X,Y
+		 * and event tag
+		 */
+		if (ret < XY_BUFSIZE)
+			goto out;
+
+		for (i = 0; i < XY_BUFSIZE; i += XY_BUFSIZE / 2) {
+			if ((buf[i + 1] & MEASURE_TAG_MASK) == MEASURE_X_TAG)
+				x = (buf[i] << XY_BUF_OFFSET) +
+				    (buf[i + 1] >> XY_BUF_OFFSET);
+			else if ((buf[i + 1] & MEASURE_TAG_MASK) == MEASURE_Y_TAG)
+				y = (buf[i] << XY_BUF_OFFSET) +
+				    (buf[i + 1] >> XY_BUF_OFFSET);
+		}
+
+		if ((buf[1] & EVENT_TAG_MASK) != (buf[3] & EVENT_TAG_MASK))
+			goto out;
+
+		switch (buf[1] & EVENT_TAG_MASK) {
+		case EVENT_INIT:
+			/* fall through */
+		case EVENT_MIDDLE:
+			input_report_abs(data->input_dev, ABS_X, x);
+			input_report_abs(data->input_dev, ABS_Y, y);
+			input_event(data->input_dev, EV_KEY, BTN_TOUCH, 1);
+			input_sync(data->input_dev);
+			break;
+
+		case EVENT_RELEASE:
+			input_event(data->input_dev, EV_KEY, BTN_TOUCH, 0);
+			input_sync(data->input_dev);
+			break;
+
+		case EVENT_FIFO_END:
+			break;
+		}
+	}
+out:
+	return IRQ_HANDLED;
+}
+
+static void __devinit max11801_ts_phy_init(struct max11801_data *data)
+{
+	struct i2c_client *client = data->client;
+
+	/* Average X,Y, take 16 samples, average eight media sample */
+	max11801_write_reg(client, MESURE_AVER_CONF_REG, 0xff);
+	/* X,Y panel setup time set to 20us */
+	max11801_write_reg(client, PANEL_SETUPTIME_CONF_REG, 0x11);
+	/* Rough pullup time (2uS), Fine pullup time (10us)  */
+	max11801_write_reg(client, TOUCH_DETECT_PULLUP_CONF_REG, 0x10);
+	/* Auto mode init period = 5ms , scan period = 5ms*/
+	max11801_write_reg(client, AUTO_MODE_TIME_CONF_REG, 0xaa);
+	/* Aperture X,Y set to +- 4LSB */
+	max11801_write_reg(client, APERTURE_CONF_REG, 0x33);
+	/* Enable Power, enable Automode, enable Aperture, enable Average X,Y */
+	max11801_write_reg(client, OP_MODE_CONF_REG, 0x36);
+}
+
+static int __devinit max11801_ts_probe(struct i2c_client *client,
+				       const struct i2c_device_id *id)
+{
+	struct max11801_data *data;
+	struct input_dev *input_dev;
+	int error;
+
+	data = kzalloc(sizeof(struct max11801_data), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!data || !input_dev) {
+		dev_err(&client->dev, "Failed to allocate memory\n");
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	data->client = client;
+	data->input_dev = input_dev;
+
+	input_dev->name = "max11801_ts";
+	input_dev->id.bustype = BUS_I2C;
+	input_dev->dev.parent = &client->dev;
+
+	__set_bit(EV_ABS, input_dev->evbit);
+	__set_bit(EV_KEY, input_dev->evbit);
+	__set_bit(BTN_TOUCH, input_dev->keybit);
+	input_set_abs_params(input_dev, ABS_X, 0, MAX11801_MAX_X, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y, 0, MAX11801_MAX_Y, 0, 0);
+	input_set_drvdata(input_dev, data);
+
+	max11801_ts_phy_init(data);
+
+	error = request_threaded_irq(client->irq, NULL, max11801_ts_interrupt,
+				     IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				     "max11801_ts", data);
+	if (error) {
+		dev_err(&client->dev, "Failed to register interrupt\n");
+		goto err_free_mem;
+	}
+
+	error = input_register_device(data->input_dev);
+	if (error)
+		goto err_free_irq;
+
+	i2c_set_clientdata(client, data);
+	return 0;
+
+err_free_irq:
+	free_irq(client->irq, data);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(data);
+	return error;
+}
+
+static __devexit int max11801_ts_remove(struct i2c_client *client)
+{
+	struct max11801_data *data = i2c_get_clientdata(client);
+
+	free_irq(client->irq, data);
+	input_unregister_device(data->input_dev);
+	kfree(data);
+
+	return 0;
+}
+
+static const struct i2c_device_id max11801_ts_id[] = {
+	{"max11801", 0},
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, max11801_ts_id);
+
+static struct i2c_driver max11801_ts_driver = {
+	.driver = {
+		.name	= "max11801_ts",
+		.owner	= THIS_MODULE,
+	},
+	.id_table	= max11801_ts_id,
+	.probe		= max11801_ts_probe,
+	.remove		= __devexit_p(max11801_ts_remove),
+};
+
+static int __init max11801_ts_init(void)
+{
+	return i2c_add_driver(&max11801_ts_driver);
+}
+
+static void __exit max11801_ts_exit(void)
+{
+	i2c_del_driver(&max11801_ts_driver);
+}
+
+module_init(max11801_ts_init);
+module_exit(max11801_ts_exit);
+
+MODULE_AUTHOR("Zhang Jiejing <jiejing.zhang@freescale.com>");
+MODULE_DESCRIPTION("Touchscreen driver for MAXI MAX11801 controller");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/gpio_keys.h b/include/linux/gpio_keys.h
index dd1a56fbe924..b5ca4b2c08ec 100644
--- a/include/linux/gpio_keys.h
+++ b/include/linux/gpio_keys.h
@@ -3,14 +3,15 @@
 
 struct gpio_keys_button {
 	/* Configuration parameters */
-	int code;		/* input event code (KEY_*, SW_*) */
+	unsigned int code;	/* input event code (KEY_*, SW_*) */
 	int gpio;
 	int active_low;
-	char *desc;
-	int type;		/* input event type (EV_KEY, EV_SW) */
+	const char *desc;
+	unsigned int type;	/* input event type (EV_KEY, EV_SW, EV_ABS) */
 	int wakeup;		/* configure the button as a wake-up source */
 	int debounce_interval;	/* debounce ticks interval in msecs */
 	bool can_disable;
+	int value;		/* axis value for EV_ABS */
 };
 
 struct gpio_keys_platform_data {
@@ -21,6 +22,7 @@ struct gpio_keys_platform_data {
 	unsigned int rep:1;		/* enable input subsystem auto repeat */
 	int (*enable)(struct device *dev);
 	void (*disable)(struct device *dev);
+	const char *name;		/* input device name */
 };
 
 #endif