Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull Devicetree updates from Rob Herring:

 - Fix a unittest failure on UML. Preparation for converting to kunit
   test framework.

 - Add annotations to dtx_diff output

 - Fix unittest reporting of expected error

 - Move DMA configuration for virtual devices into the driver that needs
   it (s5p-mfc)

 - Vendor prefixes for feiyang and techstar

 - Convert ARM GIC, GICv3, and L2x0 to DT schema

 - Add r8a7778/9 HSCIF serial bindings

* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: unittest: unflatten device tree on UML when testing
  dt-bindings: Add vendor prefix for feiyang
  dt-bindings: Add vendor prefix for techstar
  dt-bindings: display: add missing semicolon in example
  of: mark early_init_dt_alloc_reserved_memory_arch static
  of: add dtc annotations functionality to dtx_diff
  of: unittest: add caution to function header comment
  of: unittest: remove report of expected error
  dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
  dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
  dt-bindings: arm: l2x0: Convert L2 cache to json-schema
  media: s5p-mfc: Fix memdev DMA configuration
  dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings

1 files changed, 0 insertions, 114 deletions

diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt
deleted file mode 100644
index fbe6cb21f4cf..000000000000
--- a/Documentation/devicetree/bindings/arm/l2c2x0.txt
+++ /dev/null
@@ -1,114 +0,0 @@
-* ARM L2 Cache Controller
-
-ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/PL220/
-PL310 and variants) based level 2 cache controller. All these various implementations
-of the L2 cache controller have compatible programming models (Note 1).
-Some of the properties that are just prefixed "cache-*" are taken from section
-3.7.3 of the Devicetree Specification which can be found at:
-https://www.devicetree.org/specifications/
-
-The ARM L2 cache representation in the device tree should be done as follows:
-
-Required properties:
-
-- compatible : should be one of:
-  "arm,pl310-cache"
-  "arm,l220-cache"
-  "arm,l210-cache"
-  "bcm,bcm11351-a2-pl310-cache": DEPRECATED by "brcm,bcm11351-a2-pl310-cache"
-  "brcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
-     offset needs to be added to the address before passing down to the L2
-     cache controller
-  "marvell,aurora-system-cache": Marvell Controller designed to be
-     compatible with the ARM one, with system cache mode (meaning
-     maintenance operations on L1 are broadcasted to the L2 and L2
-     performs the same operation).
-  "marvell,aurora-outer-cache": Marvell Controller designed to be
-     compatible with the ARM one with outer cache mode.
-  "marvell,tauros3-cache": Marvell Tauros3 cache controller, compatible
-     with arm,pl310-cache controller.
-- cache-unified : Specifies the cache is a unified cache.
-- cache-level : Should be set to 2 for a level 2 cache.
-- reg : Physical base address and size of cache controller's memory mapped
-  registers.
-
-Optional properties:
-
-- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
-  read, write and setup latencies. Minimum valid values are 1. Controllers
-  without setup latency control should use a value of 0.
-- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
-  read, write and setup latencies. Controllers without setup latency control
-  should use 0. Controllers without separate read and write Tag RAM latency
-  values should only use the first cell.
-- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
-- arm,filter-ranges : <start length> Starting address and length of window to
-  filter. Addresses in the filter window are directed to the M1 port. Other
-  addresses will go to the M0 port.
-- arm,io-coherent : indicates that the system is operating in an hardware
-  I/O coherent mode. Valid only when the arm,pl310-cache compatible
-  string is used.
-- interrupts : 1 combined interrupt.
-- cache-size : specifies the size in bytes of the cache
-- cache-sets : specifies the number of associativity sets of the cache
-- cache-block-size : specifies the size in bytes of a cache block
-- cache-line-size : specifies the size in bytes of a line in the cache,
-  if this is not specified, the line size is assumed to be equal to the
-  cache block size
-- cache-id-part: cache id part number to be used if it is not present
-  on hardware
-- wt-override: If present then L2 is forced to Write through mode
-- arm,double-linefill : Override double linefill enable setting. Enable if
-  non-zero, disable if zero.
-- arm,double-linefill-incr : Override double linefill on INCR read. Enable
-  if non-zero, disable if zero.
-- arm,double-linefill-wrap : Override double linefill on WRAP read. Enable
-  if non-zero, disable if zero.
-- arm,prefetch-drop : Override prefetch drop enable setting. Enable if non-zero,
-  disable if zero.
-- arm,prefetch-offset : Override prefetch offset value. Valid values are
-  0-7, 15, 23, and 31.
-- arm,shared-override : The default behavior of the L220 or PL310 cache
-  controllers with respect to the shareable attribute is to transform "normal
-  memory non-cacheable transactions" into "cacheable no allocate" (for reads)
-  or "write through no write allocate" (for writes).
-  On systems where this may cause DMA buffer corruption, this property must be
-  specified to indicate that such transforms are precluded.
-- arm,parity-enable : enable parity checking on the L2 cache (L220 or PL310).
-- arm,parity-disable : disable parity checking on the L2 cache (L220 or PL310).
-- arm,outer-sync-disable : disable the outer sync operation on the L2 cache.
-  Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that
-  will randomly hang unless outer sync operations are disabled.
-- prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1>
-  (forcibly enable), property absent (retain settings set by firmware)
-- prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable),
-  <1> (forcibly enable), property absent (retain settings set by
-  firmware)
-- arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly
-  disable), <1> (forcibly enable), property absent (OS specific behavior,
-  preferably retain firmware settings)
-- arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable),
-  <1> (forcibly enable), property absent (OS specific behavior,
-  preferably retain firmware settings)
-- arm,early-bresp-disable : Disable the CA9 optimization Early BRESP (PL310)
-- arm,full-line-zero-disable : Disable the CA9 optimization Full line of zero
-  write (PL310)
-
-Example:
-
-L2: cache-controller {
-        compatible = "arm,pl310-cache";
-        reg = <0xfff12000 0x1000>;
-        arm,data-latency = <1 1 1>;
-        arm,tag-latency = <2 2 2>;
-        arm,filter-ranges = <0x80000000 0x8000000>;
-        cache-unified;
-        cache-level = <2>;
-	interrupts = <45>;
-};
-
-Note 1: The description in this document doesn't apply to integrated L2
-	cache controllers as found in e.g. Cortex-A15/A7/A57/A53. These
-	integrated L2 controllers are assumed to be all preconfigured by
-	early secure boot code. Thus no need to deal with their configuration
-	in the kernel at all.