Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...

4 files changed, 101 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt
new file mode 100644
index 000000000000..8f48aad50868
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt
@@ -0,0 +1,41 @@
+Broadcom BCM3380-style Level 1 / Level 2 interrupt controller
+
+This interrupt controller shows up in various forms on many BCM338x/BCM63xx
+chipsets.  It has the following properties:
+
+- outputs a single interrupt signal to its interrupt controller parent
+
+- contains one or more enable/status word pairs, which often appear at
+  different offsets in different blocks
+
+- no atomic set/clear operations
+
+Required properties:
+
+- compatible: should be "brcm,bcm3380-l2-intc"
+- reg: specifies one or more enable/status pairs, in the following format:
+  <enable_reg 0x4 status_reg 0x4>...
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller
+  this one is cascaded from
+- interrupts: specifies the interrupt line in the interrupt-parent controller
+  node, valid values depend on the type of parent interrupt controller
+
+Optional properties:
+
+- brcm,irq-can-wake: if present, this means the L2 controller can be used as a
+  wakeup source for system suspend/resume.
+
+Example:
+
+irq0_intc: interrupt-controller@10000020 {
+	compatible = "brcm,bcm3380-l2-intc";
+	reg = <0x10000024 0x4 0x1000002c 0x4>,
+	      <0x10000020 0x4 0x10000028 0x4>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	interrupt-parent = <&cpu_intc>;
+	interrupts = <2>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt
new file mode 100644
index 000000000000..cc217b22dccd
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt
@@ -0,0 +1,52 @@
+Broadcom BCM7038-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.  Every BCM7xxx set-top chip
+since BCM7038 has contained this hardware.
+
+Key elements of the hardware design include:
+
+- 64, 96, 128, or 160 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+  peripheral IRQs to be routed to any CPU
+
+- Atomic mask/unmask operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+  2-5 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm7038-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+  the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface.  In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+Example:
+
+periph_intc: periph_intc@1041a400 {
+        compatible = "brcm,bcm7038-l1-intc";
+        reg = <0x1041a400 0x30 0x1041a600 0x30>;
+
+        interrupt-controller;
+        #interrupt-cells = <1>;
+
+        interrupt-parent = <&cpu_intc>;
+        interrupts = <2>, <3>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
index bae1f2187226..44a9bb15dd56 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
@@ -13,8 +13,7 @@ Such an interrupt controller has the following hardware design:
   or if they will output an interrupt signal at this 2nd level interrupt
   controller, in particular for UARTs
 
-- typically has one 32-bit enable word and one 32-bit status word, but on
-  some hardware may have more than one enable/status pair
+- has one 32-bit enable word and one 32-bit status word
 
 - no atomic set/clear operations
 
@@ -53,9 +52,7 @@ The typical hardware layout for this controller is represented below:
 Required properties:
 
 - compatible: should be "brcm,bcm7120-l2-intc"
-- reg: specifies the base physical address and size of the registers;
-  multiple pairs may be specified, with the first pair handling IRQ offsets
-  0..31 and the second pair handling 32..63
+- reg: specifies the base physical address and size of the registers
 - interrupt-controller: identifies the node as an interrupt controller
 - #interrupt-cells: specifies the number of cells needed to encode an interrupt
   source, should be 1.
@@ -66,10 +63,7 @@ Required properties:
 - brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts
   are wired to this 2nd level interrupt controller, and how they match their
   respective interrupt parents. Should match exactly the number of interrupts
-  specified in the 'interrupts' property, multiplied by the number of
-  enable/status register pairs implemented by this controller.  For
-  multiple parent IRQs with multiple enable/status words, this looks like:
-  <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...>
+  specified in the 'interrupts' property.
 
 Optional properties:
 
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt
index 5a65478e5d40..aae4c384ee1f 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt
@@ -27,8 +27,13 @@ Optional properties:
 Required properties for timer sub-node:
 - compatible : Should be "mti,gic-timer".
 - interrupts : Interrupt for the GIC local timer.
+
+Optional properties for timer sub-node:
+- clocks : GIC timer operating clock.
 - clock-frequency : Clock frequency at which the GIC timers operate.
 
+Note that one of clocks or clock-frequency must be specified.
+
 Example:
 
 	gic: interrupt-controller@1bdc0000 {