Merge commit 'trivial/for-next'

6 files changed, 9 insertions, 9 deletions

diff --git a/Documentation/dell_rbu.txt b/Documentation/dell_rbu.txt
index 2c0d631de0cf..c11b931f8f98 100644
--- a/Documentation/dell_rbu.txt
+++ b/Documentation/dell_rbu.txt
@@ -81,8 +81,8 @@ Until this step is completed the driver cannot be unloaded.
 Also echoing either mono ,packet or init in to image_type will free up the
 memory allocated by the driver.
 
-If an user by accident executes steps 1 and 3 above without executing step 2;
-it will make the /sys/class/firmware/dell_rbu/ entries to disappear.
+If a user by accident executes steps 1 and 3 above without executing step 2;
+it will make the /sys/class/firmware/dell_rbu/ entries disappear.
 The entries can be recreated by doing the following
 echo init > /sys/devices/platform/dell_rbu/image_type
 NOTE: echoing init in image_type does not change it original value.
diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
index aef5a9b36846..4d184f2db0ea 100644
--- a/Documentation/hwmon/abituguru-datasheet
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more then the read address.
+write address. The write address is always one (1) more than the read address.
 
 
 uGuru ready
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index 71f0fe1fc1b0..898b4987bb80 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -1475,7 +1475,7 @@ Sysfs interface changelog:
 
 0x020100:	Marker for thinkpad-acpi with hot key NVRAM polling
 		support.  If you must, use it to know you should not
-		start an userspace NVRAM poller (allows to detect when
+		start a userspace NVRAM poller (allows to detect when
 		NVRAM is compiled out by the user because it is
 		unneeded/undesired in the first place).
 0x020101:	Marker for thinkpad-acpi with hot key NVRAM polling
diff --git a/Documentation/networking/rxrpc.txt b/Documentation/networking/rxrpc.txt
index c3669a3fb4af..60d05eb77c64 100644
--- a/Documentation/networking/rxrpc.txt
+++ b/Documentation/networking/rxrpc.txt
@@ -540,7 +540,7 @@ A client would issue an operation by:
      MSG_MORE should be set in msghdr::msg_flags on all but the last part of
      the request.  Multiple requests may be made simultaneously.
 
-     If a call is intended to go to a destination other then the default
+     If a call is intended to go to a destination other than the default
      specified through connect(), then msghdr::msg_name should be set on the
      first request message of that call.
 
diff --git a/Documentation/networking/tuntap.txt b/Documentation/networking/tuntap.txt
index 839cbb71388b..c0aab985bad9 100644
--- a/Documentation/networking/tuntap.txt
+++ b/Documentation/networking/tuntap.txt
@@ -118,7 +118,7 @@ As mentioned above, main purpose of TUN/TAP driver is tunneling.
 It is used by VTun (http://vtun.sourceforge.net).
 
 Another interesting application using TUN/TAP is pipsecd
-(http://perso.enst.fr/~beyssac/pipsec/), an userspace IPSec
+(http://perso.enst.fr/~beyssac/pipsec/), a userspace IPSec
 implementation that can use complete kernel routing (unlike FreeS/WAN).
 
 3. How does Virtual network device actually work ? 
diff --git a/Documentation/scsi/ChangeLog.lpfc b/Documentation/scsi/ChangeLog.lpfc
index ae3f962a7cfc..ff19a52fe004 100644
--- a/Documentation/scsi/ChangeLog.lpfc
+++ b/Documentation/scsi/ChangeLog.lpfc
@@ -733,7 +733,7 @@ Changes from 20040920 to 20041018
 	  I/O completion path a little more, especially taking care of
 	  fast-pathing the non-error case.  Also removes tons of dead
 	  members and defines from lpfc_scsi.h - e.g. lpfc_target is down
-	  to nothing more then the lpfc_nodelist pointer.
+	  to nothing more than the lpfc_nodelist pointer.
 	* Added binary sysfs file to issue mbox commands
 	* Replaced #if __BIG_ENDIAN with #if __BIG_ENDIAN_BITFIELD for
 	  compatibility with the user space applications.