Merge tag 'staging-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging and IIO driver updates from Greg KH:
 "Here is the "big" set of staging and IIO driver patches for 5.12-rc1.

  Nothing really huge in here, the number of staging tree patches has
  gone down for a bit, maybe there's only so much churn to happen in
  here at the moment.

  The IIO changes are:

   - new drivers

   - new DT bindings

   - new iio driver features

  with full details in the shortlog.

  The staging driver patches are just a lot of tiny coding style
  cleanups, along with some semi-larger hikey driver cleanups as those
  are _almost_ good enough to get out of the staging tree, but will
  probably have to wait until 5.13 to have happen.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (189 commits)
  staging: hikey9xx: Fix alignment of function parameters
  staging: greybus: Fixed a misspelling in hid.c
  staging: wimax/i2400m: fix some byte order issues found by sparse
  staging: wimax: i2400m: fix some incorrect type warnings
  staging: greybus: minor code style fix
  staging:wlan-ng: use memdup_user instead of kmalloc/copy_from_user
  staging:r8188eu: use IEEE80211_FCTL_* kernel definitions
  staging: rtl8192e: remove multiple blank lines
  staging: greybus: Fixed alignment issue in hid.c
  staging: wfx: remove unused included header files
  staging: nvec: minor coding style fix
  staging: wimax: Fix some coding style problem
  staging: fbtft: add tearing signal detect
  staging: vt6656: Fixed issue with alignment in rf.c
  staging: qlge: Remove duplicate word in comment
  staging: rtl8723bs: remove obsolete commented out code
  staging: rtl8723bs: fix function comments to follow kernel-doc
  staging: wfx: avoid defining array of flexible struct
  staging: rtl8723bs: Replace one-element array with flexible-array member in struct ndis_80211_var_ie
  staging: Replace lkml.org links with lore
  ...

18 files changed, 609 insertions, 132 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 35289d47d6cb..d957f5da5c04 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -198,6 +198,7 @@ Description:
 		Units after application of scale and offset are m/s^2.
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_angl_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_anglY_raw
 KernelVersion:	4.17
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -1812,3 +1813,13 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		Unscaled light intensity according to CIE 1931/DIN 5033 color space.
 		Units after application of scale are nano nanowatts per square meter.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_anglY_label
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Optional symbolic label for channel Y.
+		For Intel hid hinge sensor, the label values are:
+		hinge, keyboard, screen. It means the three channels
+		each correspond respectively to hinge angle, keyboard angle,
+		and screen angle.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac-ad5766 b/Documentation/ABI/testing/sysfs-bus-iio-dac-ad5766
new file mode 100644
index 000000000000..7fbcba15bf1e
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-dac-ad5766
@@ -0,0 +1,31 @@
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_dither_enable
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Dither enable. Write 1 to enable dither or 0 to disable it.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_dither_invert
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Inverts the dither applied to the selected DAC channel. Dither is not
+		inverted by default. Write "1" to invert dither.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_dither_scale_available
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Returns possible scalings available for the current channel.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_dither_scale
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Scales the dither before it is applied to the selected channel.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_dither_source
+KernelVersion:	5.12
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Selects dither source applied to the selected channel. Write "0" to
+		select N0 source, write "1" to select N1 source.
diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml
index 5667d09dfe6a..fbb714431e3d 100644
--- a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml
+++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml
@@ -20,6 +20,9 @@ properties:
   reg:
     maxItems: 1
 
+  vdd-supply: true
+  vddio-supply: true
+
   mount-matrix:
     description: an optional 3x3 mounting rotation matrix.
 
diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt
index e0e0755cabd8..f42e18078376 100644
--- a/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt
@@ -1,13 +1,22 @@
 Xilinx XADC device driver
 
-This binding document describes the bindings for both of them since the
-bindings are very similar. The Xilinx XADC is a ADC that can be found in the
-series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication.
-Currently two different frontends for the DRP interface exist. One that is only
-available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The
-other one is available on all series 7 platforms and is a softmacro with a AXI
-interface. This binding document describes the bindings for both of them since
-the bindings are very similar.
+This binding document describes the bindings for the Xilinx 7 Series XADC as well
+as the UltraScale/UltraScale+ System Monitor.
+
+The Xilinx XADC is an ADC that can be found in the Series 7 FPGAs from Xilinx.
+The XADC has a DRP interface for communication. Currently two different
+frontends for the DRP interface exist. One that is only available on the ZYNQ
+family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
+on all series 7 platforms and is a softmacro with a AXI interface. This binding
+document describes the bindings for both of them since the bindings are very
+similar.
+
+The Xilinx System Monitor is an ADC that is found in the UltraScale and
+UltraScale+ FPGAs from Xilinx. The System Monitor provides a DRP interface for
+communication. Xilinx provides a standard IP core that can be used to access the
+System Monitor through an AXI interface in the FPGA fabric. This IP core is
+called the Xilinx System Management Wizard. This document describes the bindings
+for this IP.
 
 Required properties:
 	- compatible: Should be one of
@@ -15,11 +24,14 @@ Required properties:
 		  configuration interface to interface to the XADC hardmacro.
 		* "xlnx,axi-xadc-1.00.a": When using the axi-xadc pcore to
 		  interface to the XADC hardmacro.
+		* "xlnx,system-management-wiz-1.3": When using the
+		  Xilinx System Management Wizard fabric IP core to access the
+		  UltraScale and UltraScale+ System Monitor.
 	- reg: Address and length of the register set for the device
 	- interrupts: Interrupt for the XADC control interface.
 	- clocks: When using the ZYNQ this must be the ZYNQ PCAP clock,
-	  when using the AXI-XADC pcore this must be the clock that provides the
-	  clock to the AXI bus interface of the core.
+	  when using the axi-xadc or the axi-system-management-wizard this must be
+	  the clock that provides the clock to the AXI bus interface of the core.
 
 Optional properties:
 	- xlnx,external-mux:
@@ -110,3 +122,20 @@ Examples:
 			};
 		};
 	};
+
+	adc@80000000 {
+		compatible = "xlnx,system-management-wiz-1.3";
+		reg = <0x80000000 0x1000>;
+		interrupts = <0 81 4>;
+		interrupt-parent = <&gic>;
+		clocks = <&fpga1_clk>;
+
+		xlnx,channels {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			channel@0 {
+				reg = <0>;
+				xlnx,bipolar;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml
new file mode 100644
index 000000000000..d5c54813ce87
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2020 Analog Devices Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/dac/adi,ad5766.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD5766 DAC device driver
+
+maintainers:
+  - Cristian Pop <cristian.pop@analog.com>
+
+description: |
+  Bindings for the Analog Devices AD5766 current DAC device. Datasheet can be
+  found here:
+    https://www.analog.com/media/en/technical-documentation/data-sheets/ad5766-5767.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ad5766
+      - adi,ad5767
+
+  output-range-microvolts:
+    description: Select converter output range.
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency:
+    maximum: 1000000
+
+  spi-cpol: true
+
+  reset-gpios:
+    description: GPIO spec for the RESET pin. As the line is active low, it
+      should be marked GPIO_ACTIVE_LOW.
+    maxItems: 1
+
+required:
+  - compatible
+  - output-range-microvolts
+  - reg
+  - spi-max-frequency
+  - spi-cpol
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          ad5766@0 {
+              compatible = "adi,ad5766";
+              output-range-microvolts = <(-5000) 5000>;
+              reg = <0>;
+              spi-cpol;
+              spi-max-frequency = <1000000>;
+              reset-gpios = <&gpio 22 0>;
+            };
+      };
diff --git a/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml b/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml
index 271998610ceb..5f5b578316bc 100644
--- a/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml
+++ b/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml
@@ -39,20 +39,39 @@ properties:
 
 allOf:
   - if:
-      not:
-        properties:
-          compatible:
-            contains:
-              const: microchip,mcp4726
+      properties:
+        compatible:
+          contains:
+            const: microchip,mcp4725
     then:
       properties:
         vref-supply: false
+      required:
+        - vdd-supply
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: microchip,mcp4726
+    then:
+      anyOf:
+        - required:
+            - vdd-supply
+        - required:
+            - vref-supply
+
+  - if:
+      not:
+        required:
+          - vref-supply
+    then:
+      properties:
         microchip,vref-buffered: false
 
 required:
   - compatible
   - reg
-  - vdd-supply
 
 additionalProperties: false
 
diff --git a/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml b/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml
index 0466483be6bb..b6bbc312a7cf 100644
--- a/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml
+++ b/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml
@@ -19,6 +19,9 @@ properties:
   reg:
     maxItems: 1
 
+  vdd-supply: true
+  vddio-supply: true
+
   interrupts:
     minItems: 1
     description:
diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
deleted file mode 100644
index 233fe207aded..000000000000
--- a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-Invensense MPU-3050 Gyroscope device tree bindings
-
-Required properties:
-  - compatible : should be "invensense,mpu3050"
-  - reg : the I2C address of the sensor
-
-Optional properties:
-  - interrupts : interrupt mapping for the trigger interrupt from the
-    internal oscillator. The following IRQ modes are supported:
-    IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and
-    IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware
-    for the desired interrupt type.
-  - vdd-supply : supply regulator for the main power voltage.
-  - vlogic-supply : supply regulator for the signal voltage.
-  - mount-matrix : see iio/mount-matrix.txt
-
-Optional subnodes:
-  - The MPU-3050 will pass through and forward the I2C signals from the
-    incoming I2C bus, alternatively drive traffic to a slave device (usually
-    an accelerometer) on its own initiative. Therefore is supports a subnode
-    i2c gate node. For details see: i2c/i2c-gate.txt
-
-Example:
-
-mpu3050@68 {
-	compatible = "invensense,mpu3050";
-	reg = <0x68>;
-	interrupt-parent = <&foo>;
-	interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
-	vdd-supply = <&bar>;
-	vlogic-supply = <&baz>;
-
-	/* External I2C interface */
-	i2c-gate {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fnord@18 {
-			compatible = "fnord";
-			reg = <0x18>;
-			interrupt-parent = <&foo>;
-			interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml
new file mode 100644
index 000000000000..7e2accc3d5ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/gyroscope/invensense,mpu3050.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Invensense MPU-3050 Gyroscope
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  compatible:
+    const: invensense,mpu3050
+
+  reg:
+    maxItems: 1
+
+  vdd-supply: true
+
+  vlogic-supply: true
+
+  interrupts:
+    minItems: 1
+    description:
+      Interrupt mapping for the trigger interrupt from the internal oscillator.
+
+  mount-matrix: true
+
+  i2c-gate:
+    $ref: /schemas/i2c/i2c-controller.yaml
+    unevaluatedProperties: false
+    description: |
+      The MPU-3050 will pass through and forward the I2C signals from the
+      incoming I2C bus, alternatively drive traffic to a slave device (usually
+      an accelerometer) on its own initiative. Therefore is supports an
+      i2c-gate subnode.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        gyroscope@68 {
+            compatible = "invensense,mpu3050";
+            reg = <0x68>;
+            interrupt-parent = <&foo>;
+            interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+            vdd-supply = <&bar>;
+            vlogic-supply = <&baz>;
+
+            i2c-gate {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                magnetometer@c {
+                    compatible = "ak,ak8975";
+                    reg = <0x0c>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
deleted file mode 100644
index f2f64749e818..000000000000
--- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS MotionTracking Device
-
-http://www.invensense.com/mems/gyro/mpu6050.html
-
-Required properties:
- - compatible : should be one of
-		"invensense,mpu6000"
-		"invensense,mpu6050"
- 		"invensense,mpu6500"
-		"invensense,mpu6515"
-		"invensense,mpu9150"
-		"invensense,mpu9250"
-		"invensense,mpu9255"
-		"invensense,icm20608"
-		"invensense,icm20609"
-		"invensense,icm20689"
-		"invensense,icm20602"
-		"invensense,icm20690"
-		"invensense,iam20680"
- - reg : the I2C address of the sensor
- - interrupts: interrupt mapping for IRQ. It should be configured with flags
-   IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
-   IRQ_TYPE_EDGE_FALLING.
-
-  Refer to interrupt-controller/interrupts.txt for generic interrupt client node
-  bindings.
-
-Optional properties:
- - vdd-supply: regulator phandle for VDD supply
- - vddio-supply: regulator phandle for VDDIO supply
- - mount-matrix: an optional 3x3 mounting rotation matrix
- - i2c-gate node.  These devices also support an auxiliary i2c bus.  This is
-   simple enough to be described using the i2c-gate binding. See
-   i2c/i2c-gate.txt for more details.
-
-Example:
-	mpu6050@68 {
-		compatible = "invensense,mpu6050";
-		reg = <0x68>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <18 IRQ_TYPE_EDGE_RISING>;
-		mount-matrix = "-0.984807753012208",  /* x0 */
-		               "0",                   /* y0 */
-		               "-0.173648177666930",  /* z0 */
-		               "0",                   /* x1 */
-		               "-1",                  /* y1 */
-		               "0",                   /* z1 */
-		               "-0.173648177666930",  /* x2 */
-		               "0",                   /* y2 */
-		               "0.984807753012208";   /* z2 */
-	};
-
-
-	mpu9250@68 {
-		compatible = "invensense,mpu9250";
-		reg = <0x68>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
-		i2c-gate {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			ax8975@c {
-				compatible = "ak,ak8975";
-				reg = <0x0c>;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/iio/imu/invensense,mpu6050.yaml b/Documentation/devicetree/bindings/iio/imu/invensense,mpu6050.yaml
new file mode 100644
index 000000000000..edbc2921aabd
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/imu/invensense,mpu6050.yaml
@@ -0,0 +1,104 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/imu/invensense,mpu6050.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS MotionTracking Device
+
+maintainers:
+  - Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
+
+description: |
+  These devices support both I2C and SPI bus interfaces.
+
+properties:
+  compatible:
+    enum:
+      - invensense,iam20680
+      - invensense,icm20608
+      - invensense,icm20609
+      - invensense,icm20689
+      - invensense,icm20602
+      - invensense,icm20690
+      - invensense,mpu6000
+      - invensense,mpu6050
+      - invensense,mpu6500
+      - invensense,mpu6515
+      - invensense,mpu6880
+      - invensense,mpu9150
+      - invensense,mpu9250
+      - invensense,mpu9255
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  spi-max-frequency: true
+
+  vdd-supply: true
+  vddio-supply: true
+
+  mount-matrix: true
+
+  i2c-gate:
+    $ref: /schemas/i2c/i2c-controller.yaml
+    unevaluatedProperties: false
+    description: |
+      These devices also support an auxiliary i2c bus via an i2c-gate.
+
+allOf:
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              enum:
+                - invensense,mpu9150
+                - invensense,mpu9250
+                - invensense,mpu9255
+    then:
+      properties:
+        i2c-gate: false
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imu@68 {
+            compatible = "invensense,mpu9250";
+            reg = <0x68>;
+            interrupt-parent = <&gpio3>;
+            interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
+            mount-matrix = "-0.984807753012208",  /* x0 */
+                           "0",                   /* y0 */
+                           "-0.173648177666930",  /* z0 */
+                           "0",                   /* x1 */
+                           "-1",                  /* y1 */
+                           "0",                   /* z1 */
+                           "-0.173648177666930",  /* x2 */
+                           "0",                   /* y2 */
+                           "0.984807753012208";   /* z2 */
+            i2c-gate {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                magnetometer@c {
+                    compatible = "ak,ak8975";
+                    reg = <0x0c>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml
index cdef7aeba708..2867ab6bf9b0 100644
--- a/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml
+++ b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml
@@ -30,6 +30,9 @@ properties:
   reg:
     maxItems: 1
 
+  vdd-supply: true
+  vddio-supply: true
+
   interrupts:
     maxItems: 1
 
diff --git a/Documentation/devicetree/bindings/iio/magnetometer/yamaha,yas530.yaml b/Documentation/devicetree/bindings/iio/magnetometer/yamaha,yas530.yaml
new file mode 100644
index 000000000000..4b0ef1ef5445
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/magnetometer/yamaha,yas530.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/magnetometer/yamaha,yas530.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Yamaha YAS530 family of magnetometer sensors
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+  The Yamaha YAS530 magnetometers is a line of 3-axis magnetometers
+  first introduced by Yamaha in 2009 with the YAS530. They are successors
+  of Yamaha's first magnetometer YAS529. Over the years this magnetometer
+  has been miniaturized and appeared in a number of different variants.
+
+properties:
+  $nodename:
+    pattern: '^magnetometer@[0-9a-f]+$'
+
+  compatible:
+    items:
+      - enum:
+          - yamaha,yas530
+          - yamaha,yas532
+          - yamaha,yas533
+          - yamaha,yas535
+          - yamaha,yas536
+          - yamaha,yas537
+          - yamaha,yas539
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: The YAS530 sensor has a RSTN pin used to reset
+      the logic inside the sensor. This GPIO line should connect
+      to that pin and be marked as GPIO_ACTIVE_LOW.
+
+  interrupts:
+    maxItems: 1
+    description: Interrupt for INT pin for interrupt generation.
+      The polarity, whether the interrupt is active on the rising
+      or the falling edge, is software-configurable in the hardware.
+
+  vdd-supply:
+    description: An optional regulator providing core power supply
+      on the VDD pin, typically 1.8 V or 3.0 V.
+
+  iovdd-supply:
+    description: An optional regulator providing I/O power supply
+      for the I2C interface on the IOVDD pin, typically 1.8 V.
+
+  mount-matrix:
+    description: An optional 3x3 mounting rotation matrix.
+
+allOf:
+  - if:
+      not:
+        properties:
+          compatible:
+            items:
+              const: yamaha,yas530
+    then:
+      properties:
+        reset-gpios: false
+
+  - if:
+      properties:
+        compatible:
+          items:
+            const: yamaha,yas539
+    then:
+      properties:
+        interrupts: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+    i2c-0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        magnetometer@2e {
+          compatible = "yamaha,yas530";
+          reg = <0x2e>;
+          vdd-supply = <&ldo1_reg>;
+          iovdd-supply = <&ldo2_reg>;
+          reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+          interrupts = <&gpio6 13 IRQ_TYPE_EDGE_RISING>;
+        };
+    };
+
+    i2c-1 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        magnetometer@2e {
+          compatible = "yamaha,yas539";
+          reg = <0x2e>;
+          vdd-supply = <&ldo1_reg>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index bdc2dc318178..a327130d1faa 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -148,15 +148,13 @@ properties:
           - maxim,max31730
             # mCube 3-axis 8-bit digital accelerometer
           - mcube,mc3230
-            # MEMSIC magnetometer
-          - memsic,mmc35240
-            # MEMSIC 2-axis 8-bit digital accelerometer
-          - memsic,mxc6225
             # Measurement Specialities I2C temperature and humidity sensor
           - meas,htu21
             # Measurement Specialities I2C pressure and temperature sensor
           - meas,ms5637
             # Measurement Specialities I2C pressure and temperature sensor
+          - meas,ms5803
+            # Measurement Specialities I2C pressure and temperature sensor
           - meas,ms5805
             # Measurement Specialities I2C pressure and temperature sensor
           - meas,ms5837
@@ -166,6 +164,10 @@ properties:
           - meas,ms8607-temppressure
             # Measurement Specialties temperature sensor
           - meas,tsys01
+            # MEMSIC magnetometer
+          - memsic,mmc35240
+            # MEMSIC 2-axis 8-bit digital accelerometer
+          - memsic,mxc6225
             # Microchip differential I2C ADC, 1 Channel, 18 bit
           - microchip,mcp3421
             # Microchip differential I2C ADC, 2 Channel, 18 bit
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 3b2958202258..f3134f44c80c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1260,6 +1260,8 @@ patternProperties:
     description: Shenzhen Xunlong Software CO.,Limited
   "^xylon,.*":
     description: Xylon
+  "^yamaha,.*":
+    description: Yamaha Corporation
   "^yes-optoelectronics,.*":
     description: Yes Optoelectronics Co.,Ltd.
   "^ylm,.*":
diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst
index a3113ffd7a16..d8279de7bf25 100644
--- a/Documentation/networking/device_drivers/index.rst
+++ b/Documentation/networking/device_drivers/index.rst
@@ -15,6 +15,7 @@ Contents:
    ethernet/index
    fddi/index
    hamradio/index
+   qlogic/index
    wan/index
    wifi/index
 
diff --git a/Documentation/networking/device_drivers/qlogic/index.rst b/Documentation/networking/device_drivers/qlogic/index.rst
new file mode 100644
index 000000000000..ad05b04286e4
--- /dev/null
+++ b/Documentation/networking/device_drivers/qlogic/index.rst
@@ -0,0 +1,18 @@
+.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+QLogic QLGE Device Drivers
+===============================================
+
+Contents:
+
+.. toctree::
+   :maxdepth: 2
+
+   qlge
+
+.. only::  subproject and html
+
+   Indices
+   =======
+
+   * :ref:`genindex`
diff --git a/Documentation/networking/device_drivers/qlogic/qlge.rst b/Documentation/networking/device_drivers/qlogic/qlge.rst
new file mode 100644
index 000000000000..0b888253d152
--- /dev/null
+++ b/Documentation/networking/device_drivers/qlogic/qlge.rst
@@ -0,0 +1,118 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=======================================
+QLogic QLGE 10Gb Ethernet device driver
+=======================================
+
+This driver use drgn and devlink for debugging.
+
+Dump kernel data structures in drgn
+-----------------------------------
+
+To dump kernel data structures, the following Python script can be used
+in drgn:
+
+.. code-block:: python
+
+	def align(x, a):
+	    """the alignment a should be a power of 2
+	    """
+	    mask = a - 1
+	    return (x+ mask) & ~mask
+
+	def struct_size(struct_type):
+	    struct_str = "struct {}".format(struct_type)
+	    return sizeof(Object(prog, struct_str, address=0x0))
+
+	def netdev_priv(netdevice):
+	    NETDEV_ALIGN = 32
+	    return netdevice.value_() + align(struct_size("net_device"), NETDEV_ALIGN)
+
+	name = 'xxx'
+	qlge_device = None
+	netdevices = prog['init_net'].dev_base_head.address_of_()
+	for netdevice in list_for_each_entry("struct net_device", netdevices, "dev_list"):
+	    if netdevice.name.string_().decode('ascii') == name:
+	        print(netdevice.name)
+
+	ql_adapter = Object(prog, "struct ql_adapter", address=netdev_priv(qlge_device))
+
+The struct ql_adapter will be printed in drgn as follows,
+
+    >>> ql_adapter
+    (struct ql_adapter){
+            .ricb = (struct ricb){
+                    .base_cq = (u8)0,
+                    .flags = (u8)120,
+                    .mask = (__le16)26637,
+                    .hash_cq_id = (u8 [1024]){ 172, 142, 255, 255 },
+                    .ipv6_hash_key = (__le32 [10]){},
+                    .ipv4_hash_key = (__le32 [4]){},
+            },
+            .flags = (unsigned long)0,
+            .wol = (u32)0,
+            .nic_stats = (struct nic_stats){
+                    .tx_pkts = (u64)0,
+                    .tx_bytes = (u64)0,
+                    .tx_mcast_pkts = (u64)0,
+                    .tx_bcast_pkts = (u64)0,
+                    .tx_ucast_pkts = (u64)0,
+                    .tx_ctl_pkts = (u64)0,
+                    .tx_pause_pkts = (u64)0,
+                    ...
+            },
+            .active_vlans = (unsigned long [64]){
+                    0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 52780853100545, 18446744073709551615,
+                    18446619461681283072, 0, 42949673024, 2147483647,
+            },
+            .rx_ring = (struct rx_ring [17]){
+                    {
+                            .cqicb = (struct cqicb){
+                                    .msix_vect = (u8)0,
+                                    .reserved1 = (u8)0,
+                                    .reserved2 = (u8)0,
+                                    .flags = (u8)0,
+                                    .len = (__le16)0,
+                                    .rid = (__le16)0,
+                                    ...
+                            },
+                            .cq_base = (void *)0x0,
+                            .cq_base_dma = (dma_addr_t)0,
+                    }
+                    ...
+            }
+    }
+
+coredump via devlink
+--------------------
+
+
+And the coredump obtained via devlink in json format looks like,
+
+.. code:: shell
+
+	$ devlink health dump show DEVICE reporter coredump -p -j
+	{
+	    "Core Registers": {
+	        "segment": 1,
+	        "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ]
+	    },
+	    "Test Logic Regs": {
+	        "segment": 2,
+	        "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ]
+	    },
+	    "RMII Registers": {
+	        "segment": 3,
+	        "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ]
+	    },
+	    ...
+	    "Sem Registers": {
+	        "segment": 50,
+	        "values": [ 0,0,0,0 ]
+	    }
+	}
+
+When the module parameter qlge_force_coredump is set to be true, the MPI
+RISC reset before coredumping. So coredumping will much longer since
+devlink tool has to wait for 5 secs for the resetting to be
+finished.