MIPS: SGI-IP27: use generic PCI driver

Converted bridge code to a platform driver using the PCI generic driver
framework and use adding platform devices during xtalk scan. This allows
easier sharing bridge driver for other SGI platforms like IP30 (Octane) and
IP35 (Origin 3k, Fuel, Tezro).

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
[paul.burton@mips.com:
  - Leave __phys_to_dma(), __dma_to_phys() & pcibus_to_node() in
    arch/mips/pci/pci-ip27.c since the motivation for moving them
    disappeared when the driver stopped being moved to drivers/pci.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

1 files changed, 0 insertions, 181 deletions

diff --git a/arch/mips/pci/pci-ip27.c b/arch/mips/pci/pci-ip27.c
index 3c177b4d0609..441eb9383b20 100644
--- a/arch/mips/pci/pci-ip27.c
+++ b/arch/mips/pci/pci-ip27.c
@@ -7,162 +7,7 @@
  * Copyright (C) 1999, 2000, 04 Ralf Baechle (ralf@linux-mips.org)
  * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
  */
-#include <linux/kernel.h>
-#include <linux/export.h>
-#include <linux/pci.h>
-#include <linux/smp.h>
-#include <linux/dma-direct.h>
-#include <asm/sn/arch.h>
 #include <asm/pci/bridge.h>
-#include <asm/paccess.h>
-#include <asm/sn/intr.h>
-#include <asm/sn/sn0/hub.h>
-
-/*
- * Max #PCI busses we can handle; ie, max #PCI bridges.
- */
-#define MAX_PCI_BUSSES		40
-
-/*
- * XXX: No kmalloc available when we do our crosstalk scan,
- *	we should try to move it later in the boot process.
- */
-static struct bridge_controller bridges[MAX_PCI_BUSSES];
-
-extern struct pci_ops bridge_pci_ops;
-
-int bridge_probe(nasid_t nasid, int widget_id, int masterwid)
-{
-	unsigned long offset = NODE_OFFSET(nasid);
-	struct bridge_controller *bc;
-	static int num_bridges = 0;
-	int slot;
-
-	pci_set_flags(PCI_PROBE_ONLY);
-
-	printk("a bridge\n");
-
-	/* XXX: kludge alert.. */
-	if (!num_bridges)
-		ioport_resource.end = ~0UL;
-
-	bc = &bridges[num_bridges];
-
-	bc->pc.pci_ops		= &bridge_pci_ops;
-	bc->pc.mem_resource	= &bc->mem;
-	bc->pc.io_resource	= &bc->io;
-
-	bc->pc.index		= num_bridges;
-
-	bc->mem.name		= "Bridge PCI MEM";
-	bc->pc.mem_offset	= offset;
-	bc->mem.start		= 0;
-	bc->mem.end		= ~0UL;
-	bc->mem.flags		= IORESOURCE_MEM;
-
-	bc->io.name		= "Bridge IO MEM";
-	bc->pc.io_offset	= offset;
-	bc->io.start		= 0UL;
-	bc->io.end		= ~0UL;
-	bc->io.flags		= IORESOURCE_IO;
-
-	bc->widget_id = widget_id;
-	bc->nasid = nasid;
-
-	bc->baddr = (u64)masterwid << 60 | PCI64_ATTR_BAR;
-
-	/*
-	 * point to this bridge
-	 */
-	bc->base = (struct bridge_regs *)RAW_NODE_SWIN_BASE(nasid, widget_id);
-
-	/*
-	 * Clear all pending interrupts.
-	 */
-	bridge_write(bc, b_int_rst_stat, BRIDGE_IRR_ALL_CLR);
-
-	/*
-	 * Until otherwise set up, assume all interrupts are from slot 0
-	 */
-	bridge_write(bc, b_int_device, 0x0);
-
-	/*
-	 * swap pio's to pci mem and io space (big windows)
-	 */
-	bridge_set(bc, b_wid_control, BRIDGE_CTRL_IO_SWAP |
-				      BRIDGE_CTRL_MEM_SWAP);
-#ifdef CONFIG_PAGE_SIZE_4KB
-	bridge_clr(bc, b_wid_control, BRIDGE_CTRL_PAGE_SIZE);
-#else /* 16kB or larger */
-	bridge_set(bc, b_wid_control, BRIDGE_CTRL_PAGE_SIZE);
-#endif
-
-	/*
-	 * Hmm...  IRIX sets additional bits in the address which
-	 * are documented as reserved in the bridge docs.
-	 */
-	bridge_write(bc, b_wid_int_upper, 0x8000 | (masterwid << 16));
-	bridge_write(bc, b_wid_int_lower, 0x01800090); /* PI_INT_PEND_MOD off*/
-	bridge_write(bc, b_dir_map, (masterwid << 20));	/* DMA */
-	bridge_write(bc, b_int_enable, 0);
-
-	for (slot = 0; slot < 8; slot ++) {
-		bridge_set(bc, b_device[slot].reg, BRIDGE_DEV_SWAP_DIR);
-		bc->pci_int[slot] = -1;
-	}
-	bridge_read(bc, b_wid_tflush);	  /* wait until Bridge PIO complete */
-
-	register_pci_controller(&bc->pc);
-
-	num_bridges++;
-
-	return 0;
-}
-
-/*
- * All observed requests have pin == 1. We could have a global here, that
- * gets incremented and returned every time - unfortunately, pci_map_irq
- * may be called on the same device over and over, and need to return the
- * same value. On O2000, pin can be 0 or 1, and PCI slots can be [0..7].
- *
- * A given PCI device, in general, should be able to intr any of the cpus
- * on any one of the hubs connected to its xbow.
- */
-int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	return 0;
-}
-
-static inline struct pci_dev *bridge_root_dev(struct pci_dev *dev)
-{
-	while (dev->bus->parent) {
-		/* Move up the chain of bridges. */
-		dev = dev->bus->self;
-	}
-
-	return dev;
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
-	struct bridge_controller *bc = BRIDGE_CONTROLLER(dev->bus);
-	struct pci_dev *rdev = bridge_root_dev(dev);
-	int slot = PCI_SLOT(rdev->devfn);
-	int irq;
-
-	irq = bc->pci_int[slot];
-	if (irq == -1) {
-		irq = request_bridge_irq(bc, slot);
-		if (irq < 0)
-			return irq;
-
-		bc->pci_int[slot] = irq;
-	}
-	dev->irq = irq;
-
-	return 0;
-}
 
 dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
 {
@@ -177,29 +22,6 @@ phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t dma_addr)
 	return dma_addr & ~(0xffUL << 56);
 }
 
-/*
- * Device might live on a subordinate PCI bus.	XXX Walk up the chain of buses
- * to find the slot number in sense of the bridge device register.
- * XXX This also means multiple devices might rely on conflicting bridge
- * settings.
- */
-
-static inline void pci_disable_swapping(struct pci_dev *dev)
-{
-	struct bridge_controller *bc = BRIDGE_CONTROLLER(dev->bus);
-	struct bridge_regs *bridge = bc->base;
-	int slot = PCI_SLOT(dev->devfn);
-
-	/* Turn off byte swapping */
-	bridge->b_device[slot].reg &= ~BRIDGE_DEV_SWAP_DIR;
-	bridge->b_widget.w_tflush;	/* Flush */
-}
-
-static void pci_fixup_ioc3(struct pci_dev *d)
-{
-	pci_disable_swapping(d);
-}
-
 #ifdef CONFIG_NUMA
 int pcibus_to_node(struct pci_bus *bus)
 {
@@ -209,6 +31,3 @@ int pcibus_to_node(struct pci_bus *bus)
 }
 EXPORT_SYMBOL(pcibus_to_node);
 #endif /* CONFIG_NUMA */
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
-	pci_fixup_ioc3);