ath10k: update bss channel survey information

During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).

To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.

Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

1 files changed, 29 insertions, 0 deletions

diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index af97759f5ca3..f71c1fb0b237 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -4798,8 +4798,11 @@ static int ath10k_wmi_event_pdev_bss_chan_info(struct ath10k *ar,
 					       struct sk_buff *skb)
 {
 	struct wmi_pdev_bss_chan_info_event *ev;
+	struct survey_info *survey;
 	u64 busy, total, tx, rx, rx_bss;
 	u32 freq, noise_floor;
+	u32 cc_freq_hz = ar->hw_params.channel_counters_freq_hz;
+	int idx;
 
 	ev = (struct wmi_pdev_bss_chan_info_event *)skb->data;
 	if (WARN_ON(skb->len < sizeof(*ev)))
@@ -4817,6 +4820,29 @@ static int ath10k_wmi_event_pdev_bss_chan_info(struct ath10k *ar,
 		   "wmi event pdev bss chan info:\n freq: %d noise: %d cycle: busy %llu total %llu tx %llu rx %llu rx_bss %llu\n",
 		   freq, noise_floor, busy, total, tx, rx, rx_bss);
 
+	spin_lock_bh(&ar->data_lock);
+	idx = freq_to_idx(ar, freq);
+	if (idx >= ARRAY_SIZE(ar->survey)) {
+		ath10k_warn(ar, "bss chan info: invalid frequency %d (idx %d out of bounds)\n",
+			    freq, idx);
+		goto exit;
+	}
+
+	survey = &ar->survey[idx];
+
+	survey->noise     = noise_floor;
+	survey->time      = div_u64(total, cc_freq_hz);
+	survey->time_busy = div_u64(busy, cc_freq_hz);
+	survey->time_rx   = div_u64(rx_bss, cc_freq_hz);
+	survey->time_tx   = div_u64(tx, cc_freq_hz);
+	survey->filled   |= (SURVEY_INFO_NOISE_DBM |
+			     SURVEY_INFO_TIME |
+			     SURVEY_INFO_TIME_BUSY |
+			     SURVEY_INFO_TIME_RX |
+			     SURVEY_INFO_TIME_TX);
+exit:
+	spin_unlock_bh(&ar->data_lock);
+	complete(&ar->bss_survey_done);
 	return 0;
 }
 
@@ -5640,6 +5666,9 @@ static struct sk_buff *ath10k_wmi_10_2_op_gen_init(struct ath10k *ar)
 	if (ath10k_peer_stats_enabled(ar))
 		features |= WMI_10_2_PEER_STATS;
 
+	if (test_bit(WMI_SERVICE_BSS_CHANNEL_INFO_64, ar->wmi.svc_map))
+		features |= WMI_10_2_BSS_CHAN_INFO;
+
 	cmd->resource_config.feature_mask = __cpu_to_le32(features);
 
 	memcpy(&cmd->resource_config.common, &config, sizeof(config));