Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

Pull PCI updates from Bjorn Helgaas:
 "Enumeration:

   - Rework portdrv shutdown so it disables interrupts but doesn't
     disable bus mastering, which leads to hangs on Loongson LS7A

   - Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
     again to avoid hardware issues on Loongson LS7A (and likely other
     devices based on DesignWare IP)

   - Ignore devices with a firmware (DT or ACPI) node that says the
     device is disabled

  Resource management:

   - Distribute spare resources to unconfigured hotplug bridges at
     boot-time (not just when hot-adding such a bridge), which makes
     hot-adding devices to docks work better. Tried this in v6.1 but had
     to revert for regressions, so try again

   - Fix root bus issue that dropped resources that happened to end
     at 0, e.g., [bus 00]

  PCI device hotplug:

   - Remove device locking when marking device as disconnected so this
     doesn't have to wait for concurrent driver bind/unbind to complete

   - Quirk more Qualcomm bridges that don't fully implement the PCIe
     Slot Status 'Command Completed' bit

  Power management:

   - Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
     don't miss hot-add notifications for USB4 docks, Thunderbolt, etc

  Reset:

   - Observe delay after reset, e.g., resuming from system sleep,
     regardless of whether a bridge can suspend to D3cold at runtime

   - Wait for secondary bus to become ready after a bridge reset

  Virtualization:

   - Avoid FLR on some AMD FCH AHCI adapters where it doesn't work

   - Allow independent IOMMU groups for some Wangxun NICs that prevent
     peer-to-peer transactions but don't advertise an ACS Capability

  Error handling:

   - Configure End-to-End-CRC (ECRC) only if Linux owns the AER
     Capability

   - Remove redundant Device Control Error Reporting Enable in the AER
     service driver since this is already done for all devices during
     enumeration

  ASPM:

   - Add pci_enable_link_state() interface to allow drivers to enable
     ASPM link state

  Endpoint framework:

   - Move dra7xx and tegra194 linkup processing from hard IRQ to
     threaded IRQ handler

   - Add a separate lock for endpoint controller list of endpoint
     function drivers to prevent deadlock in callbacks

   - Pass events from endpoint controller to endpoint function drivers
     via callbacks instead of notifiers

  Synopsys DesignWare eDMA controller driver (acked by Vinod):

   - Fix CPU vs PCI address issues

   - Fix source vs destination address issues

   - Fix issues with interleaved transfer semantics

   - Fix channel count initialization issue (issue still exists in
     several other drivers)

   - Clean up and improve debugfs usage so it will work on platforms
     with several eDMA devices

  Baikal T-1 PCIe controller driver:

   - Set a 64-bit DMA mask

  Freescale i.MX6 PCIe controller driver:

   - Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
     support

  Intel VMD host bridge driver:

   - Add quirk to configure PCIe ASPM and LTR. This is normally done by
     BIOS, and will be for future products

  Marvell MVEBU PCIe controller driver:

   - Mark this driver as broken in Kconfig since bugs prevent its daily
     usage

  MediaTek MT7621 PCIe controller driver:

   - Delay PHY port initialization to improve boot reliability for ZBT
     WE1326, ZBT WF3526-P, and some Netgear models

  Qualcomm PCIe controller driver:

   - Add MSM8998 DT compatible string

   - Unify MSM8996 and MSM8998 clock orderings

   - Add SM8350 DT binding and driver support

   - Add IPQ8074 Gen3 DT binding and driver support

   - Correct qcom,perst-regs in DT binding

   - Add qcom_pcie_host_deinit() so the PHY is powered off and
     regulators and clocks are disabled on late host-init errors

  Socionext UniPhier Pro5 controller driver:

   - Clean up uniphier-ep reg, clocks, resets, and their names in DT
     binding

  Synopsys DesignWare PCIe controller driver:

   - Restrict coherent DMA mask to 32 bits for MSI, but allow controller
     drivers to set 64-bit streaming DMA mask

   - Add eDMA engine support in both Root Port and Endpoint controllers

  Miscellaneous:

   - Remove MODULE_LICENSE from boolean drivers so they don't look like
     modules so modprobe can complain about them"

* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
  PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
  PCI: bt1: Set 64-bit DMA mask
  PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
  dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
  dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
  dmaengine: dw-edma: Add mem-mapped LL-entries support
  PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
  PCI: hv: Drop duplicate PCI_MSI dependency
  PCI/P2PDMA: Annotate RCU dereference
  PCI/sysfs: Constify struct kobj_type pci_slot_ktype
  PCI: hotplug: Allow marking devices as disconnected during bind/unbind
  PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
  PCI: qcom: Add IPQ8074 Gen3 port support
  dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
  dt-bindings: PCI: qcom: Sort compatibles alphabetically
  PCI: qcom: Fix host-init error handling
  PCI: qcom: Add SM8350 support
  dt-bindings: PCI: qcom: Add SM8350
  dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
  dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
  ...

1 files changed, 182 insertions, 18 deletions

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 1dde5c579edc..55a0405b921d 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -52,6 +52,9 @@ enum imx6_pcie_variants {
 	IMX8MQ,
 	IMX8MM,
 	IMX8MP,
+	IMX8MQ_EP,
+	IMX8MM_EP,
+	IMX8MP_EP,
 };
 
 #define IMX6_PCIE_FLAG_IMX6_PHY			BIT(0)
@@ -60,6 +63,7 @@ enum imx6_pcie_variants {
 
 struct imx6_pcie_drvdata {
 	enum imx6_pcie_variants variant;
+	enum dw_pcie_device_mode mode;
 	u32 flags;
 	int dbi_length;
 	const char *gpr;
@@ -152,24 +156,39 @@ struct imx6_pcie {
 static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
 {
 	WARN_ON(imx6_pcie->drvdata->variant != IMX8MQ &&
+		imx6_pcie->drvdata->variant != IMX8MQ_EP &&
 		imx6_pcie->drvdata->variant != IMX8MM &&
-		imx6_pcie->drvdata->variant != IMX8MP);
+		imx6_pcie->drvdata->variant != IMX8MM_EP &&
+		imx6_pcie->drvdata->variant != IMX8MP &&
+		imx6_pcie->drvdata->variant != IMX8MP_EP);
 	return imx6_pcie->controller_id == 1 ? IOMUXC_GPR16 : IOMUXC_GPR14;
 }
 
 static void imx6_pcie_configure_type(struct imx6_pcie *imx6_pcie)
 {
-	unsigned int mask, val;
+	unsigned int mask, val, mode;
 
-	if (imx6_pcie->drvdata->variant == IMX8MQ &&
-	    imx6_pcie->controller_id == 1) {
-		mask = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE;
-		val  = FIELD_PREP(IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
-				  PCI_EXP_TYPE_ROOT_PORT);
-	} else {
+	if (imx6_pcie->drvdata->mode == DW_PCIE_EP_TYPE)
+		mode = PCI_EXP_TYPE_ENDPOINT;
+	else
+		mode = PCI_EXP_TYPE_ROOT_PORT;
+
+	switch (imx6_pcie->drvdata->variant) {
+	case IMX8MQ:
+	case IMX8MQ_EP:
+		if (imx6_pcie->controller_id == 1) {
+			mask = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE;
+			val  = FIELD_PREP(IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
+					  mode);
+		} else {
+			mask = IMX6Q_GPR12_DEVICE_TYPE;
+			val  = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, mode);
+		}
+		break;
+	default:
 		mask = IMX6Q_GPR12_DEVICE_TYPE;
-		val  = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE,
-				  PCI_EXP_TYPE_ROOT_PORT);
+		val  = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, mode);
+		break;
 	}
 
 	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, mask, val);
@@ -304,13 +323,16 @@ static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
 {
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		/*
 		 * The PHY initialization had been done in the PHY
 		 * driver, break here directly.
 		 */
 		break;
 	case IMX8MQ:
+	case IMX8MQ_EP:
 		/*
 		 * TODO: Currently this code assumes external
 		 * oscillator is being used
@@ -561,8 +583,11 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 	case IMX7D:
 		break;
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MQ:
+	case IMX8MQ_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		ret = clk_prepare_enable(imx6_pcie->pcie_aux);
 		if (ret) {
 			dev_err(dev, "unable to enable pcie_aux clock\n");
@@ -606,8 +631,11 @@ static void imx6_pcie_disable_ref_clk(struct imx6_pcie *imx6_pcie)
 				   IMX7D_GPR12_PCIE_PHY_REFCLK_SEL);
 		break;
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MQ:
+	case IMX8MQ_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		clk_disable_unprepare(imx6_pcie->pcie_aux);
 		break;
 	default:
@@ -672,10 +700,13 @@ static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX7D:
 	case IMX8MQ:
+	case IMX8MQ_EP:
 		reset_control_assert(imx6_pcie->pciephy_reset);
 		fallthrough;
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		reset_control_assert(imx6_pcie->apps_reset);
 		break;
 	case IMX6SX:
@@ -713,6 +744,7 @@ static int imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
 
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX8MQ:
+	case IMX8MQ_EP:
 		reset_control_deassert(imx6_pcie->pciephy_reset);
 		break;
 	case IMX7D:
@@ -751,7 +783,9 @@ static int imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
 		break;
 	case IMX6Q:		/* Nothing to do */
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		break;
 	}
 
@@ -800,8 +834,11 @@ static void imx6_pcie_ltssm_enable(struct device *dev)
 		break;
 	case IMX7D:
 	case IMX8MQ:
+	case IMX8MQ_EP:
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		reset_control_deassert(imx6_pcie->apps_reset);
 		break;
 	}
@@ -820,8 +857,11 @@ static void imx6_pcie_ltssm_disable(struct device *dev)
 		break;
 	case IMX7D:
 	case IMX8MQ:
+	case IMX8MQ_EP:
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		reset_control_assert(imx6_pcie->apps_reset);
 		break;
 	}
@@ -1003,8 +1043,104 @@ static const struct dw_pcie_host_ops imx6_pcie_host_ops = {
 
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.start_link = imx6_pcie_start_link,
+	.stop_link = imx6_pcie_stop_link,
+};
+
+static void imx6_pcie_ep_init(struct dw_pcie_ep *ep)
+{
+	enum pci_barno bar;
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+
+	for (bar = BAR_0; bar <= BAR_5; bar++)
+		dw_pcie_ep_reset_bar(pci, bar);
+}
+
+static int imx6_pcie_ep_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
+				  enum pci_epc_irq_type type,
+				  u16 interrupt_num)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+
+	switch (type) {
+	case PCI_EPC_IRQ_LEGACY:
+		return dw_pcie_ep_raise_legacy_irq(ep, func_no);
+	case PCI_EPC_IRQ_MSI:
+		return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num);
+	case PCI_EPC_IRQ_MSIX:
+		return dw_pcie_ep_raise_msix_irq(ep, func_no, interrupt_num);
+	default:
+		dev_err(pci->dev, "UNKNOWN IRQ type\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct pci_epc_features imx8m_pcie_epc_features = {
+	.linkup_notifier = false,
+	.msi_capable = true,
+	.msix_capable = false,
+	.reserved_bar = 1 << BAR_1 | 1 << BAR_3,
+	.align = SZ_64K,
+};
+
+static const struct pci_epc_features*
+imx6_pcie_ep_get_features(struct dw_pcie_ep *ep)
+{
+	return &imx8m_pcie_epc_features;
+}
+
+static const struct dw_pcie_ep_ops pcie_ep_ops = {
+	.ep_init = imx6_pcie_ep_init,
+	.raise_irq = imx6_pcie_ep_raise_irq,
+	.get_features = imx6_pcie_ep_get_features,
 };
 
+static int imx6_add_pcie_ep(struct imx6_pcie *imx6_pcie,
+			   struct platform_device *pdev)
+{
+	int ret;
+	unsigned int pcie_dbi2_offset;
+	struct dw_pcie_ep *ep;
+	struct resource *res;
+	struct dw_pcie *pci = imx6_pcie->pci;
+	struct dw_pcie_rp *pp = &pci->pp;
+	struct device *dev = pci->dev;
+
+	imx6_pcie_host_init(pp);
+	ep = &pci->ep;
+	ep->ops = &pcie_ep_ops;
+
+	switch (imx6_pcie->drvdata->variant) {
+	case IMX8MQ_EP:
+	case IMX8MM_EP:
+	case IMX8MP_EP:
+		pcie_dbi2_offset = SZ_1M;
+		break;
+	default:
+		pcie_dbi2_offset = SZ_4K;
+		break;
+	}
+	pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "addr_space");
+	if (!res)
+		return -EINVAL;
+
+	ep->phys_base = res->start;
+	ep->addr_size = resource_size(res);
+	ep->page_size = SZ_64K;
+
+	ret = dw_pcie_ep_init(ep);
+	if (ret) {
+		dev_err(dev, "failed to initialize endpoint\n");
+		return ret;
+	}
+	/* Start LTSSM. */
+	imx6_pcie_ltssm_enable(dev);
+
+	return 0;
+}
+
 static void imx6_pcie_pm_turnoff(struct imx6_pcie *imx6_pcie)
 {
 	struct device *dev = imx6_pcie->pci->dev;
@@ -1166,6 +1302,7 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 					     "pcie_inbound_axi clock missing or invalid\n");
 		break;
 	case IMX8MQ:
+	case IMX8MQ_EP:
 		imx6_pcie->pcie_aux = devm_clk_get(dev, "pcie_aux");
 		if (IS_ERR(imx6_pcie->pcie_aux))
 			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_aux),
@@ -1190,7 +1327,9 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 		}
 		break;
 	case IMX8MM:
+	case IMX8MM_EP:
 	case IMX8MP:
+	case IMX8MP_EP:
 		imx6_pcie->pcie_aux = devm_clk_get(dev, "pcie_aux");
 		if (IS_ERR(imx6_pcie->pcie_aux))
 			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_aux),
@@ -1279,15 +1418,22 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = dw_pcie_host_init(&pci->pp);
-	if (ret < 0)
-		return ret;
+	if (imx6_pcie->drvdata->mode == DW_PCIE_EP_TYPE) {
+		ret = imx6_add_pcie_ep(imx6_pcie, pdev);
+		if (ret < 0)
+			return ret;
+	} else {
+		ret = dw_pcie_host_init(&pci->pp);
+		if (ret < 0)
+			return ret;
+
+		if (pci_msi_enabled()) {
+			u8 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
 
-	if (pci_msi_enabled()) {
-		u8 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
-		val = dw_pcie_readw_dbi(pci, offset + PCI_MSI_FLAGS);
-		val |= PCI_MSI_FLAGS_ENABLE;
-		dw_pcie_writew_dbi(pci, offset + PCI_MSI_FLAGS, val);
+			val = dw_pcie_readw_dbi(pci, offset + PCI_MSI_FLAGS);
+			val |= PCI_MSI_FLAGS_ENABLE;
+			dw_pcie_writew_dbi(pci, offset + PCI_MSI_FLAGS, val);
+		}
 	}
 
 	return 0;
@@ -1343,6 +1489,21 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 	},
+	[IMX8MQ_EP] = {
+		.variant = IMX8MQ_EP,
+		.mode = DW_PCIE_EP_TYPE,
+		.gpr = "fsl,imx8mq-iomuxc-gpr",
+	},
+	[IMX8MM_EP] = {
+		.variant = IMX8MM_EP,
+		.mode = DW_PCIE_EP_TYPE,
+		.gpr = "fsl,imx8mm-iomuxc-gpr",
+	},
+	[IMX8MP_EP] = {
+		.variant = IMX8MP_EP,
+		.mode = DW_PCIE_EP_TYPE,
+		.gpr = "fsl,imx8mp-iomuxc-gpr",
+	},
 };
 
 static const struct of_device_id imx6_pcie_of_match[] = {
@@ -1353,6 +1514,9 @@ static const struct of_device_id imx6_pcie_of_match[] = {
 	{ .compatible = "fsl,imx8mq-pcie", .data = &drvdata[IMX8MQ], },
 	{ .compatible = "fsl,imx8mm-pcie", .data = &drvdata[IMX8MM], },
 	{ .compatible = "fsl,imx8mp-pcie", .data = &drvdata[IMX8MP], },
+	{ .compatible = "fsl,imx8mq-pcie-ep", .data = &drvdata[IMX8MQ_EP], },
+	{ .compatible = "fsl,imx8mm-pcie-ep", .data = &drvdata[IMX8MM_EP], },
+	{ .compatible = "fsl,imx8mp-pcie-ep", .data = &drvdata[IMX8MP_EP], },
 	{},
 };