Merge branch 'pci/controller/qcom'

- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
  writing out all the clock names (Manivannan Sadhasivam)

- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)

- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
  (HDMA) (Manivannan Sadhasivam)

- Enable drivers to supply the eDMA channel count since some can't auto
  detect this (Manivannan Sadhasivam)

- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)

- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
  (Mrinmay Sarkar)

- Make sure resources are disabled during PERST# assertion, even if the
  link is already disabled (Manivannan Sadhasivam)

- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
  even if other drivers don't vote for it (Krishna chaitanya chundru)

- Add Operating Performance Points (OPP) to scale performance state based
  on aggregate link bandwidth to improve SoC power efficiency (Krishna
  chaitanya chundru)

- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
  (Dan Carpenter)

- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
  (Dan Carpenter)

- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
  Carpenter)

* pci/controller/qcom:
  PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
  PCI: qcom: Prevent potential error pointer dereference
  PCI: qcom: Fix missing error code in qcom_pcie_probe()
  PCI: qcom: Add OPP support to scale performance
  PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
  PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
  PCI: qcom-ep: Disable resources unconditionally during PERST# assert
  PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
  PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
  PCI: epf-mhi: Enable HDMA for SA8775P SoC
  PCI: qcom-ep: Add HDMA support for SA8775P SoC
  PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
  PCI: dwc: Skip finding eDMA channels count for HDMA platforms
  PCI: dwc: Refactor dw_pcie_edma_find_chip() API
  PCI: qcom-ep: Add support for SA8775P SOC
  dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
  PCI: qcom: Use devm_clk_bulk_get_all() API

1 files changed, 49 insertions, 16 deletions

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 26ecf0472f86..1b5aba1f0c92 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -870,30 +870,40 @@ static struct dw_edma_plat_ops dw_pcie_edma_ops = {
 	.irq_vector = dw_pcie_edma_irq_vector,
 };
 
-static int dw_pcie_edma_find_chip(struct dw_pcie *pci)
+static void dw_pcie_edma_init_data(struct dw_pcie *pci)
+{
+	pci->edma.dev = pci->dev;
+
+	if (!pci->edma.ops)
+		pci->edma.ops = &dw_pcie_edma_ops;
+
+	pci->edma.flags |= DW_EDMA_CHIP_LOCAL;
+}
+
+static int dw_pcie_edma_find_mf(struct dw_pcie *pci)
 {
 	u32 val;
 
 	/*
+	 * Bail out finding the mapping format if it is already set by the glue
+	 * driver. Also ensure that the edma.reg_base is pointing to a valid
+	 * memory region.
+	 */
+	if (pci->edma.mf != EDMA_MF_EDMA_LEGACY)
+		return pci->edma.reg_base ? 0 : -ENODEV;
+
+	/*
 	 * Indirect eDMA CSRs access has been completely removed since v5.40a
 	 * thus no space is now reserved for the eDMA channels viewport and
 	 * former DMA CTRL register is no longer fixed to FFs.
-	 *
-	 * Note that Renesas R-Car S4-8's PCIe controllers for unknown reason
-	 * have zeros in the eDMA CTRL register even though the HW-manual
-	 * explicitly states there must FFs if the unrolled mapping is enabled.
-	 * For such cases the low-level drivers are supposed to manually
-	 * activate the unrolled mapping to bypass the auto-detection procedure.
 	 */
-	if (dw_pcie_ver_is_ge(pci, 540A) || dw_pcie_cap_is(pci, EDMA_UNROLL))
+	if (dw_pcie_ver_is_ge(pci, 540A))
 		val = 0xFFFFFFFF;
 	else
 		val = dw_pcie_readl_dbi(pci, PCIE_DMA_VIEWPORT_BASE + PCIE_DMA_CTRL);
 
 	if (val == 0xFFFFFFFF && pci->edma.reg_base) {
 		pci->edma.mf = EDMA_MF_EDMA_UNROLL;
-
-		val = dw_pcie_readl_dma(pci, PCIE_DMA_CTRL);
 	} else if (val != 0xFFFFFFFF) {
 		pci->edma.mf = EDMA_MF_EDMA_LEGACY;
 
@@ -902,15 +912,25 @@ static int dw_pcie_edma_find_chip(struct dw_pcie *pci)
 		return -ENODEV;
 	}
 
-	pci->edma.dev = pci->dev;
+	return 0;
+}
 
-	if (!pci->edma.ops)
-		pci->edma.ops = &dw_pcie_edma_ops;
+static int dw_pcie_edma_find_channels(struct dw_pcie *pci)
+{
+	u32 val;
 
-	pci->edma.flags |= DW_EDMA_CHIP_LOCAL;
+	/*
+	 * Autodetect the read/write channels count only for non-HDMA platforms.
+	 * HDMA platforms with native CSR mapping doesn't support autodetect,
+	 * so the glue drivers should've passed the valid count already. If not,
+	 * the below sanity check will catch it.
+	 */
+	if (pci->edma.mf != EDMA_MF_HDMA_NATIVE) {
+		val = dw_pcie_readl_dma(pci, PCIE_DMA_CTRL);
 
-	pci->edma.ll_wr_cnt = FIELD_GET(PCIE_DMA_NUM_WR_CHAN, val);
-	pci->edma.ll_rd_cnt = FIELD_GET(PCIE_DMA_NUM_RD_CHAN, val);
+		pci->edma.ll_wr_cnt = FIELD_GET(PCIE_DMA_NUM_WR_CHAN, val);
+		pci->edma.ll_rd_cnt = FIELD_GET(PCIE_DMA_NUM_RD_CHAN, val);
+	}
 
 	/* Sanity check the channels count if the mapping was incorrect */
 	if (!pci->edma.ll_wr_cnt || pci->edma.ll_wr_cnt > EDMA_MAX_WR_CH ||
@@ -920,6 +940,19 @@ static int dw_pcie_edma_find_chip(struct dw_pcie *pci)
 	return 0;
 }
 
+static int dw_pcie_edma_find_chip(struct dw_pcie *pci)
+{
+	int ret;
+
+	dw_pcie_edma_init_data(pci);
+
+	ret = dw_pcie_edma_find_mf(pci);
+	if (ret)
+		return ret;
+
+	return dw_pcie_edma_find_channels(pci);
+}
+
 static int dw_pcie_edma_irq_verify(struct dw_pcie *pci)
 {
 	struct platform_device *pdev = to_platform_device(pci->dev);