Merge tag 'spi-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A fairly quiet release for the SPI subsystem:

   - Move to using IDR for allocating bus numbers

   - Modernisation of the ep93xx driver, removing a lot of open coding
     and using the framework more

   - The tools have been moved to use the standard tools build system
     and an install target added (there will be a fairly trivial
     conflict with tip resulting from the changes in the main tools
     Makefile)

   - A refactoring of the Qualcomm QUP driver which enables new variants
     to be supported

   - Explicit support for the Freescale i.MX53 and i.MX6 SPI, Renesas
     R-Car H3 and Rockchip RV1108 controllers"

* tag 'spi-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (71 commits)
  spi: spi-falcon: drop check of boot select
  spi: imx: fix use of native chip-selects with devicetree
  spi: pl022: constify amba_id
  spi: imx: fix little-endian build
  spi: omap: Allocate bus number from spi framework
  spi: Kernel coding style fixes
  spi: imx: dynamic burst length adjust for PIO mode
  spi: Pick spi bus number from Linux idr or spi alias
  spi: rockchip: configure CTRLR1 according to size and data frame
  spi: altera: Consolidate TX/RX data register access
  spi: altera: Switch to SPI core transfer queue management
  spi: rockchip: add compatible string for rv1108 spi
  spi: qup: fix 64-bit build warning
  spi: qup: hide warning for uninitialized variable
  spi: spi-ep93xx: use the default master transfer queueing mechanism
  spi: spi-ep93xx: remove private data 'current_msg'
  spi: spi-ep93xx: pass the spi_master pointer around
  spi: spi-ep93xx: absorb the interrupt enable/disable helpers
  spi: spi-ep93xx: add spi master prepare_transfer_hardware()
  spi: spi-ep93xx: use 32-bit read/write for all registers
  ...

1 files changed, 28 insertions, 6 deletions

diff --git a/drivers/spi/spi-loopback-test.c b/drivers/spi/spi-loopback-test.c
index 3459965004f8..bed7403bb6b3 100644
--- a/drivers/spi/spi-loopback-test.c
+++ b/drivers/spi/spi-loopback-test.c
@@ -32,39 +32,50 @@
 #include "spi-test.h"
 
 /* flag to only simulate transfers */
-int simulate_only;
+static int simulate_only;
 module_param(simulate_only, int, 0);
 MODULE_PARM_DESC(simulate_only, "if not 0 do not execute the spi message");
 
 /* dump spi messages */
-int dump_messages;
+static int dump_messages;
 module_param(dump_messages, int, 0);
 MODULE_PARM_DESC(dump_messages,
 		 "=1 dump the basic spi_message_structure, " \
 		 "=2 dump the spi_message_structure including data, " \
 		 "=3 dump the spi_message structure before and after execution");
 /* the device is jumpered for loopback - enabling some rx_buf tests */
-int loopback;
+static int loopback;
 module_param(loopback, int, 0);
 MODULE_PARM_DESC(loopback,
 		 "if set enable loopback mode, where the rx_buf "	\
 		 "is checked to match tx_buf after the spi_message "	\
 		 "is executed");
 
+static int loop_req;
+module_param(loop_req, int, 0);
+MODULE_PARM_DESC(loop_req,
+		 "if set controller will be asked to enable test loop mode. " \
+		 "If controller supported it, MISO and MOSI will be connected");
+
+static int no_cs;
+module_param(no_cs, int, 0);
+MODULE_PARM_DESC(no_cs,
+		 "if set Chip Select (CS) will not be used");
+
 /* run only a specific test */
-int run_only_test = -1;
+static int run_only_test = -1;
 module_param(run_only_test, int, 0);
 MODULE_PARM_DESC(run_only_test,
 		 "only run the test with this number (0-based !)");
 
 /* use vmalloc'ed buffers */
-int use_vmalloc;
+static int use_vmalloc;
 module_param(use_vmalloc, int, 0644);
 MODULE_PARM_DESC(use_vmalloc,
 		 "use vmalloc'ed buffers instead of kmalloc'ed");
 
 /* check rx ranges */
-int check_ranges = 1;
+static int check_ranges = 1;
 module_param(check_ranges, int, 0644);
 MODULE_PARM_DESC(check_ranges,
 		 "checks rx_buffer pattern are valid");
@@ -313,6 +324,17 @@ static int spi_loopback_test_probe(struct spi_device *spi)
 {
 	int ret;
 
+	if (loop_req || no_cs) {
+		spi->mode |= loop_req ? SPI_LOOP : 0;
+		spi->mode |= no_cs ? SPI_NO_CS : 0;
+		ret = spi_setup(spi);
+		if (ret) {
+			dev_err(&spi->dev, "SPI setup with SPI_LOOP or SPI_NO_CS failed (%d)\n",
+				ret);
+			return ret;
+		}
+	}
+
 	dev_info(&spi->dev, "Executing spi-loopback-tests\n");
 
 	ret = spi_test_run_tests(spi, spi_tests);