summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/devicetree/bindings/leds/leds-lm36274.txt85
-rw-r--r--Documentation/devicetree/bindings/leds/leds-lm3697.txt73
-rw-r--r--Documentation/devicetree/bindings/leds/leds-spi-byte.txt44
-rw-r--r--Documentation/devicetree/bindings/mfd/ti-lmu.txt88
-rw-r--r--Documentation/laptops/thinkpad-acpi.txt4
-rw-r--r--Documentation/leds/index.rst25
-rw-r--r--Documentation/leds/leds-blinkm.rst (renamed from Documentation/leds/leds-blinkm.txt)64
-rw-r--r--Documentation/leds/leds-class-flash.rst (renamed from Documentation/leds/leds-class-flash.txt)49
-rw-r--r--Documentation/leds/leds-class.rst (renamed from Documentation/leds/leds-class.txt)15
-rw-r--r--Documentation/leds/leds-lm3556.rst (renamed from Documentation/leds/leds-lm3556.txt)100
-rw-r--r--Documentation/leds/leds-lp3944.rst (renamed from Documentation/leds/leds-lp3944.txt)23
-rw-r--r--Documentation/leds/leds-lp5521.rst115
-rw-r--r--Documentation/leds/leds-lp5521.txt101
-rw-r--r--Documentation/leds/leds-lp5523.rst147
-rw-r--r--Documentation/leds/leds-lp5523.txt130
-rw-r--r--Documentation/leds/leds-lp5562.rst137
-rw-r--r--Documentation/leds/leds-lp5562.txt120
-rw-r--r--Documentation/leds/leds-lp55xx.rst224
-rw-r--r--Documentation/leds/leds-lp55xx.txt194
-rw-r--r--Documentation/leds/leds-mlxcpld.rst118
-rw-r--r--Documentation/leds/leds-mlxcpld.txt110
-rw-r--r--Documentation/leds/ledtrig-oneshot.rst (renamed from Documentation/leds/ledtrig-oneshot.txt)11
-rw-r--r--Documentation/leds/ledtrig-transient.rst (renamed from Documentation/leds/ledtrig-transient.txt)65
-rw-r--r--Documentation/leds/ledtrig-usbport.rst (renamed from Documentation/leds/ledtrig-usbport.txt)11
-rw-r--r--Documentation/leds/uleds.rst (renamed from Documentation/leds/uleds.txt)5
-rw-r--r--MAINTAINERS2
-rw-r--r--drivers/leds/Kconfig35
-rw-r--r--drivers/leds/Makefile4
-rw-r--r--drivers/leds/leds-lm36274.c172
-rw-r--r--drivers/leds/leds-lm3697.c395
-rw-r--r--drivers/leds/leds-max77650.c2
-rw-r--r--drivers/leds/leds-pca955x.c2
-rw-r--r--drivers/leds/leds-spi-byte.c161
-rw-r--r--drivers/leds/leds-tca6507.c2
-rw-r--r--drivers/leds/leds-ti-lmu-common.c156
-rw-r--r--drivers/leds/trigger/Kconfig2
-rw-r--r--drivers/leds/trigger/ledtrig-transient.c2
-rw-r--r--drivers/mfd/Kconfig5
-rw-r--r--drivers/mfd/ti-lmu.c23
-rw-r--r--drivers/regulator/Kconfig2
-rw-r--r--drivers/regulator/lm363x-regulator.c78
-rw-r--r--include/linux/leds-ti-lmu-common.h47
-rw-r--r--include/linux/mfd/ti-lmu-register.h63
-rw-r--r--include/linux/mfd/ti-lmu.h5
-rw-r--r--net/netfilter/Kconfig2
45 files changed, 2350 insertions, 868 deletions
diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt
new file mode 100644
index 000000000000..39c230d59a4d
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt
@@ -0,0 +1,85 @@
+* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias
+
+The LM36274 is an integrated four-channel WLED driver and LCD bias supply.
+The backlight boost provides the power to bias four parallel LED strings with
+up to 29V total output voltage. The 11-bit LED current is programmable via
+the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA.
+
+Parent device properties are documented in
+Documentation/devicetree/bindings/mfd/ti-lmu.txt
+
+Regulator properties are documented in
+Documentation/devicetree/bindings/regulator/lm363x-regulator.txt
+
+Required backlight properties:
+ - compatible:
+ "ti,lm36274-backlight"
+ - reg : 0
+ - #address-cells : 1
+ - #size-cells : 0
+ - led-sources : Indicates which LED strings will be enabled.
+ Values from 0-3, sources is 0 based so strings will be
+ source value + 1.
+
+Optional backlight properties:
+ - label : see Documentation/devicetree/bindings/leds/common.txt
+ - linux,default-trigger :
+ see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is
+controlled by control bank B.
+
+lm36274@11 {
+ compatible = "ti,lm36274";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11>;
+
+ enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,lm363x-regulator";
+
+ enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+ <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+ vboost {
+ regulator-name = "lcd_boost";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <7150000>;
+ regulator-always-on;
+ };
+
+ vpos {
+ regulator-name = "lcd_vpos";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6500000>;
+ };
+
+ vneg {
+ regulator-name = "lcd_vneg";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6500000>;
+ };
+ };
+
+ backlight {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,lm36274-backlight";
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 2>;
+ label = "white:backlight_cluster";
+ linux,default-trigger = "backlight";
+ };
+ };
+};
+
+For more product information please see the link below:
+http://www.ti.com/lit/ds/symlink/lm36274.pdf
diff --git a/Documentation/devicetree/bindings/leds/leds-lm3697.txt b/Documentation/devicetree/bindings/leds/leds-lm3697.txt
new file mode 100644
index 000000000000..63992d732959
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lm3697.txt
@@ -0,0 +1,73 @@
+* Texas Instruments - LM3697 Highly Efficient White LED Driver
+
+The LM3697 11-bit LED driver provides high-
+performance backlight dimming for 1, 2, or 3 series
+LED strings while delivering up to 90% efficiency.
+
+This device is suitable for display and keypad lighting
+
+Required properties:
+ - compatible:
+ "ti,lm3697"
+ - reg : I2C slave address
+ - #address-cells : 1
+ - #size-cells : 0
+
+Optional properties:
+ - enable-gpios : GPIO pin to enable/disable the device
+ - vled-supply : LED supply
+
+Required child properties:
+ - reg : 0 - LED is Controlled by bank A
+ 1 - LED is Controlled by bank B
+ - led-sources : Indicates which HVLED string is associated to which
+ control bank. This is a zero based property so
+ HVLED1 = 0, HVLED2 = 1, HVLED3 = 2.
+ Additional information is contained
+ in Documentation/devicetree/bindings/leds/common.txt
+
+Optional child properties:
+ - ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+ - ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+ - ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt
+ - label : see Documentation/devicetree/bindings/leds/common.txt
+ - linux,default-trigger :
+ see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is
+controlled by control bank B.
+
+led-controller@36 {
+ compatible = "ti,lm3697";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x36>;
+
+ enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ vled-supply = <&vbatt>;
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 2>;
+ ti,brightness-resolution = <2047>;
+ ramp-up-us = <5000>;
+ ramp-down-us = <1000>;
+ label = "white:first_backlight_cluster";
+ linux,default-trigger = "backlight";
+ };
+
+ led@1 {
+ reg = <1>;
+ led-sources = <1>;
+ ti,brightness-resolution = <255>;
+ ramp-up-us = <500>;
+ ramp-down-us = <1000>;
+ label = "white:second_backlight_cluster";
+ linux,default-trigger = "backlight";
+ };
+}
+
+For more product information please see the link below:
+http://www.ti.com/lit/ds/symlink/lm3697.pdf
diff --git a/Documentation/devicetree/bindings/leds/leds-spi-byte.txt b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt
new file mode 100644
index 000000000000..28b6b2d9091e
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt
@@ -0,0 +1,44 @@
+* Single Byte SPI LED Device Driver.
+
+The driver can be used for controllers with a very simple SPI protocol:
+- one LED is controlled by a single byte on MOSI
+- the value of the byte gives the brightness between two values (lowest to
+ highest)
+- no return value is necessary (no MISO signal)
+
+The value for lowest and highest brightness is dependent on the device and
+therefore on the compatible string.
+
+Depending on the compatible string some special functions (like hardware
+accelerated blinking) might can be supported too.
+
+The driver currently only supports one LED. The properties of the LED are
+configured in a sub-node in the device node.
+
+Required properties:
+- compatible: should be one of
+ * "ubnt,acb-spi-led" microcontroller (SONiX 8F26E611LA) based device
+ used for example in Ubiquiti airCube ISP
+
+Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
+apply.
+
+LED sub-node properties:
+- label:
+ see Documentation/devicetree/bindings/leds/common.txt
+- default-state:
+ see Documentation/devicetree/bindings/leds/common.txt
+ Only "on" and "off" are supported.
+
+Example:
+
+led-controller@0 {
+ compatible = "ubnt,acb-spi-led";
+ reg = <0>;
+ spi-max-frequency = <100000>;
+
+ led {
+ label = "white:status";
+ default-state = "on";
+ };
+};
diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
index 86ca786d54fc..2296b8f24de4 100644
--- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt
+++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
@@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below.
LM3632 Backlight and regulator
LM3633 Backlight, LED and fault monitor
LM3695 Backlight
- LM3697 Backlight and fault monitor
+ LM36274 Backlight and regulator
Required properties:
- compatible: Should be one of:
@@ -16,15 +16,32 @@ Required properties:
"ti,lm3632"
"ti,lm3633"
"ti,lm3695"
- "ti,lm3697"
+ "ti,lm36274"
- reg: I2C slave address.
0x11 for LM3632
0x29 for LM3631
- 0x36 for LM3633, LM3697
+ 0x36 for LM3633
0x63 for LM3695
+ 0x11 for LM36274
-Optional property:
+Optional properties:
- enable-gpios: A GPIO specifier for hardware enable pin.
+ - ramp-up-us: Current ramping from one brightness level to
+ the a higher brightness level.
+ Range from 2048 us - 117.44 s
+ - ramp-down-us: Current ramping from one brightness level to
+ the a lower brightness level.
+ Range from 2048 us - 117.44 s
+ - ti,brightness-resolution - This determines whether to use 8 bit brightness
+ mode or 11 bit brightness mode. If this value is
+ not set the device is defaulted to the preferred
+ 8bit brightness mode per 7.3.4.1 of the data
+ sheet. This setting can either be in the parent
+ node or as part of the LED child nodes. This
+ is determined by the part itself if the strings
+ have a common brightness register or individual
+ brightness registers.
+ The values are 255 (8bit) or 2047 (11bit).
Required node:
- backlight: All LMU devices have backlight child nodes.
@@ -35,14 +52,15 @@ Optional nodes:
Required properties:
- compatible: Should be one of:
"ti,lm3633-fault-monitor"
- "ti,lm3697-fault-monitor"
- leds: LED properties for LM3633. Please refer to [2].
+ LED properties for LM36274. Please refer to [4].
- regulators: Regulator properties for LM3631 and LM3632.
Please refer to [3].
[1] ../leds/backlight/ti-lmu-backlight.txt
[2] ../leds/leds-lm3633.txt
[3] ../regulator/lm363x-regulator.txt
+[4] ../leds/leds-lm36274.txt
lm3631@29 {
compatible = "ti,lm3631";
@@ -90,7 +108,7 @@ lm3631@29 {
lcd_bl {
led-sources = <0 1>;
- ramp-up-msec = <300>;
+ ramp-up-us = <300000>;
};
};
};
@@ -152,15 +170,15 @@ lm3633@36 {
main {
label = "main_lcd";
led-sources = <1 2>;
- ramp-up-msec = <500>;
- ramp-down-msec = <500>;
+ ramp-up-us = <500000>;
+ ramp-down-us = <500000>;
};
front {
label = "front_lcd";
led-sources = <0>;
- ramp-up-msec = <1000>;
- ramp-down-msec = <0>;
+ ramp-up-us = <1000000>;
+ ramp-down-us = <0>;
};
};
@@ -201,23 +219,51 @@ lm3695@63 {
};
};
-lm3697@36 {
- compatible = "ti,lm3697";
- reg = <0x36>;
+lm36274@11 {
+ compatible = "ti,lm36274";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11>;
enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,lm363x-regulator";
- backlight {
- compatible = "ti,lm3697-backlight";
+ enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+ <&pioC 1 GPIO_ACTIVE_HIGH>;
- lcd {
- led-sources = <0 1 2>;
- ramp-up-msec = <200>;
- ramp-down-msec = <200>;
+ vboost {
+ regulator-name = "lcd_boost";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <7150000>;
+ regulator-always-on;
+ };
+
+ vpos {
+ regulator-name = "lcd_vpos";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6500000>;
+ };
+
+ vneg {
+ regulator-name = "lcd_vneg";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6500000>;
};
};
- fault-monitor {
- compatible = "ti,lm3697-fault-monitor";
+ backlight {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,lm36274-backlight";
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 2>;
+ label = "white:backlight_cluster";
+ linux,default-trigger = "backlight";
+ };
};
};
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index 6cced88de6da..75ef063622d2 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -679,7 +679,7 @@ status as "unknown". The available commands are:
sysfs notes:
The ThinkLight sysfs interface is documented by the LED class
-documentation, in Documentation/leds/leds-class.txt. The ThinkLight LED name
+documentation, in Documentation/leds/leds-class.rst. The ThinkLight LED name
is "tpacpi::thinklight".
Due to limitations in the sysfs LED class, if the status of the ThinkLight
@@ -779,7 +779,7 @@ All of the above can be turned on and off and can be made to blink.
sysfs notes:
The ThinkPad LED sysfs interface is described in detail by the LED class
-documentation, in Documentation/leds/leds-class.txt.
+documentation, in Documentation/leds/leds-class.rst.
The LEDs are named (in LED ID order, from 0 to 12):
"tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt",
diff --git a/Documentation/leds/index.rst b/Documentation/leds/index.rst
new file mode 100644
index 000000000000..9885f7c1b75d
--- /dev/null
+++ b/Documentation/leds/index.rst
@@ -0,0 +1,25 @@
+:orphan:
+
+====
+LEDs
+====
+
+.. toctree::
+ :maxdepth: 1
+
+ leds-class
+ leds-class-flash
+ ledtrig-oneshot
+ ledtrig-transient
+ ledtrig-usbport
+
+ uleds
+
+ leds-blinkm
+ leds-lm3556
+ leds-lp3944
+ leds-lp5521
+ leds-lp5523
+ leds-lp5562
+ leds-lp55xx
+ leds-mlxcpld
diff --git a/Documentation/leds/leds-blinkm.txt b/Documentation/leds/leds-blinkm.rst
index 9dd92f4cf4e1..c74b5bc877b1 100644
--- a/Documentation/leds/leds-blinkm.txt
+++ b/Documentation/leds/leds-blinkm.rst
@@ -1,3 +1,7 @@
+==================
+Leds BlinkM driver
+==================
+
The leds-blinkm driver supports the devices of the BlinkM family.
They are RGB-LED modules driven by a (AT)tiny microcontroller and
@@ -14,35 +18,36 @@ The interface this driver provides is 2-fold:
a) LED class interface for use with triggers
############################################
-The registration follows the scheme:
-blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
+The registration follows the scheme::
+
+ blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
-$ ls -h /sys/class/leds/blinkm-6-*
-/sys/class/leds/blinkm-6-9-blue:
-brightness device max_brightness power subsystem trigger uevent
+ $ ls -h /sys/class/leds/blinkm-6-*
+ /sys/class/leds/blinkm-6-9-blue:
+ brightness device max_brightness power subsystem trigger uevent
-/sys/class/leds/blinkm-6-9-green:
-brightness device max_brightness power subsystem trigger uevent
+ /sys/class/leds/blinkm-6-9-green:
+ brightness device max_brightness power subsystem trigger uevent
-/sys/class/leds/blinkm-6-9-red:
-brightness device max_brightness power subsystem trigger uevent
+ /sys/class/leds/blinkm-6-9-red:
+ brightness device max_brightness power subsystem trigger uevent
(same is /sys/bus/i2c/devices/6-0009/leds)
We can control the colors separated into red, green and blue and
assign triggers on each color.
-E.g.:
+E.g.::
-$ cat blinkm-6-9-blue/brightness
-05
+ $ cat blinkm-6-9-blue/brightness
+ 05
-$ echo 200 > blinkm-6-9-blue/brightness
-$
+ $ echo 200 > blinkm-6-9-blue/brightness
+ $
-$ modprobe ledtrig-heartbeat
-$ echo heartbeat > blinkm-6-9-green/trigger
-$
+ $ modprobe ledtrig-heartbeat
+ $ echo heartbeat > blinkm-6-9-green/trigger
+ $
b) Sysfs group to control rgb, fade, hsb, scripts ...
@@ -52,29 +57,28 @@ This extended interface is available as folder blinkm
in the sysfs folder of the I2C device.
E.g. below /sys/bus/i2c/devices/6-0009/blinkm
-$ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
-blue green red test
+ $ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
+ blue green red test
Currently supported is just setting red, green, blue
and a test sequence.
-E.g.:
+E.g.::
-$ cat *
-00
-00
-00
-#Write into test to start test sequence!#
+ $ cat *
+ 00
+ 00
+ 00
+ #Write into test to start test sequence!#
-$ echo 1 > test
-$
+ $ echo 1 > test
+ $
-$ echo 255 > red
-$
+ $ echo 255 > red
+ $
as of 6/2012
dl9pf <at> gmx <dot> de
-
diff --git a/Documentation/leds/leds-class-flash.txt b/Documentation/leds/leds-class-flash.rst
index 8da3c6f4b60b..6ec12c5a1a0e 100644
--- a/Documentation/leds/leds-class-flash.txt
+++ b/Documentation/leds/leds-class-flash.rst
@@ -1,9 +1,9 @@
-
+==============================
Flash LED handling under Linux
==============================
Some LED devices provide two modes - torch and flash. In the LED subsystem
-those modes are supported by LED class (see Documentation/leds/leds-class.txt)
+those modes are supported by LED class (see Documentation/leds/leds-class.rst)
and LED Flash class respectively. The torch mode related features are enabled
by default and the flash ones only if a driver declares it by setting
LED_DEV_CAP_FLASH flag.
@@ -14,6 +14,7 @@ registered in the LED subsystem with led_classdev_flash_register function.
Following sysfs attributes are exposed for controlling flash LED devices:
(see Documentation/ABI/testing/sysfs-class-led-flash)
+
- flash_brightness
- max_flash_brightness
- flash_timeout
@@ -31,30 +32,46 @@ be defined in the kernel config.
The driver must call the v4l2_flash_init function to get registered in the
V4L2 subsystem. The function takes six arguments:
-- dev : flash device, e.g. an I2C device
-- of_node : of_node of the LED, may be NULL if the same as device's
-- fled_cdev : LED flash class device to wrap
-- iled_cdev : LED flash class device representing indicator LED associated with
- fled_cdev, may be NULL
-- ops : V4L2 specific ops
- * external_strobe_set - defines the source of the flash LED strobe -
+
+- dev:
+ flash device, e.g. an I2C device
+- of_node:
+ of_node of the LED, may be NULL if the same as device's
+- fled_cdev:
+ LED flash class device to wrap
+- iled_cdev:
+ LED flash class device representing indicator LED associated with
+ fled_cdev, may be NULL
+- ops:
+ V4L2 specific ops
+
+ * external_strobe_set
+ defines the source of the flash LED strobe -
V4L2_CID_FLASH_STROBE control or external source, typically
a sensor, which makes it possible to synchronise the flash
strobe start with exposure start,
- * intensity_to_led_brightness and led_brightness_to_intensity - perform
+ * intensity_to_led_brightness and led_brightness_to_intensity
+ perform
enum led_brightness <-> V4L2 intensity conversion in a device
specific manner - they can be used for devices with non-linear
LED current scale.
-- config : configuration for V4L2 Flash sub-device
- * dev_name - the name of the media entity, unique in the system,
- * flash_faults - bitmask of flash faults that the LED flash class
+- config:
+ configuration for V4L2 Flash sub-device
+
+ * dev_name
+ the name of the media entity, unique in the system,
+ * flash_faults
+ bitmask of flash faults that the LED flash class
device can report; corresponding LED_FAULT* bit definitions are
available in <linux/led-class-flash.h>,
- * torch_intensity - constraints for the LED in TORCH mode
+ * torch_intensity
+ constraints for the LED in TORCH mode
in microamperes,
- * indicator_intensity - constraints for the indicator LED
+ * indicator_intensity
+ constraints for the indicator LED
in microamperes,
- * has_external_strobe - determines whether the flash strobe source
+ * has_external_strobe
+ determines whether the flash strobe source
can be switched to external,
On remove the v4l2_flash_release function has to be called, which takes one
diff --git a/Documentation/leds/leds-class.txt b/Documentation/leds/leds-class.rst
index 8b39cc6b03ee..df0120a1ee3c 100644
--- a/Documentation/leds/leds-class.txt
+++ b/Documentation/leds/leds-class.rst
@@ -1,4 +1,4 @@
-
+========================
LED handling under Linux
========================
@@ -43,7 +43,7 @@ LED Device Naming
Is currently of the form:
-"devicename:colour:function"
+ "devicename:colour:function"
There have been calls for LED properties such as colour to be exported as
individual led class attributes. As a solution which doesn't incur as much
@@ -57,9 +57,12 @@ Brightness setting API
LED subsystem core exposes following API for setting brightness:
- - led_set_brightness : it is guaranteed not to sleep, passing LED_OFF stops
+ - led_set_brightness:
+ it is guaranteed not to sleep, passing LED_OFF stops
blinking,
- - led_set_brightness_sync : for use cases when immediate effect is desired -
+
+ - led_set_brightness_sync:
+ for use cases when immediate effect is desired -
it can block the caller for the time required for accessing
device registers and can sleep, passing LED_OFF stops hardware
blinking, returns -EBUSY if software blink fallback is enabled.
@@ -70,7 +73,7 @@ LED registration API
A driver wanting to register a LED classdev for use by other drivers /
userspace needs to allocate and fill a led_classdev struct and then call
-[devm_]led_classdev_register. If the non devm version is used the driver
+`[devm_]led_classdev_register`. If the non devm version is used the driver
must call led_classdev_unregister from its remove function before
free-ing the led_classdev struct.
@@ -94,7 +97,7 @@ with brightness value LED_OFF, which should stop any software
timers that may have been required for blinking.
The blink_set() function should choose a user friendly blinking value
-if it is called with *delay_on==0 && *delay_off==0 parameters. In this
+if it is called with `*delay_on==0` && `*delay_off==0` parameters. In this
case the driver should give back the chosen value through delay_on and
delay_off parameters to the leds subsystem.
diff --git a/Documentation/leds/leds-lm3556.txt b/Documentation/leds/leds-lm3556.rst
index 62278e871b50..1ef17d7d800e 100644
--- a/Documentation/leds/leds-lm3556.txt
+++ b/Documentation/leds/leds-lm3556.rst
@@ -1,68 +1,118 @@
+========================
Kernel driver for lm3556
========================
-*Texas Instrument:
- 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
+* Texas Instrument:
+ 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
* Datasheet: http://www.national.com/ds/LM/LM3556.pdf
Authors:
- Daniel Jeong
+ - Daniel Jeong
+
Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
Description
-----------
There are 3 functions in LM3556, Flash, Torch and Indicator.
-FLASH MODE
+Flash Mode
+^^^^^^^^^^
+
In Flash Mode, the LED current source(LED) provides 16 target current levels
from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
or by pulling the STROBE pin HIGH.
+
LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
+
* if STROBE pin is enabled, below example control brightness only, and
-ON / OFF will be controlled by STROBE pin.
+ ON / OFF will be controlled by STROBE pin.
Flash Example:
-OFF : #echo 0 > sys/class/leds/flash/brightness
-93.75 mA: #echo 1 > sys/class/leds/flash/brightness
-... .....
-1500 mA: #echo 16 > sys/class/leds/flash/brightness
-TORCH MODE
+OFF::
+
+ #echo 0 > sys/class/leds/flash/brightness
+
+93.75 mA::
+
+ #echo 1 > sys/class/leds/flash/brightness
+
+...
+
+1500 mA::
+
+ #echo 16 > sys/class/leds/flash/brightness
+
+Torch Mode
+^^^^^^^^^^
+
In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
hardware TORCH input.
+
LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
* if TORCH pin is enabled, below example control brightness only,
and ON / OFF will be controlled by TORCH pin.
Torch Example:
-OFF : #echo 0 > sys/class/leds/torch/brightness
-46.88 mA: #echo 1 > sys/class/leds/torch/brightness
-... .....
-375 mA : #echo 8 > sys/class/leds/torch/brightness
-INDICATOR MODE
+OFF::
+
+ #echo 0 > sys/class/leds/torch/brightness
+
+46.88 mA::
+
+ #echo 1 > sys/class/leds/torch/brightness
+
+...
+
+375 mA::
+
+ #echo 8 > sys/class/leds/torch/brightness
+
+Indicator Mode
+^^^^^^^^^^^^^^
+
Indicator pattern can be set through sys/class/leds/indicator/pattern file,
and 4 patterns are pre-defined in indicator_pattern array.
+
According to N-lank, Pulse time and N Period values, different pattern wiill
be generated.If you want new patterns for your own device, change
indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
+
Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
Indicator pattern example:
-pattern 0: #echo 0 > sys/class/leds/indicator/pattern
-....
-pattern 3: #echo 3 > sys/class/leds/indicator/pattern
+
+pattern 0::
+
+ #echo 0 > sys/class/leds/indicator/pattern
+
+...
+
+pattern 3::
+
+ #echo 3 > sys/class/leds/indicator/pattern
Indicator brightness can be controlled through
sys/class/leds/indicator/brightness file.
Example:
-OFF : #echo 0 > sys/class/leds/indicator/brightness
-5.86 mA : #echo 1 > sys/class/leds/indicator/brightness
-........
-46.875mA : #echo 8 > sys/class/leds/indicator/brightness
+
+OFF::
+
+ #echo 0 > sys/class/leds/indicator/brightness
+
+5.86 mA::
+
+ #echo 1 > sys/class/leds/indicator/brightness
+
+...
+
+46.875mA::
+
+ #echo 8 > sys/class/leds/indicator/brightness
Notes
-----
@@ -70,7 +120,8 @@ Driver expects it is registered using the i2c_board_info mechanism.
To register the chip at address 0x63 on specific adapter, set the platform data
according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
-Example:
+Example::
+
static struct i2c_board_info board_i2c_ch4[] __initdata = {
{
I2C_BOARD_INFO(LM3556_NAME, 0x63),
@@ -80,6 +131,7 @@ Example:
and register it in the platform init function
-Example:
+Example::
+
board_register_i2c_bus(4, 400,
board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));
diff --git a/Documentation/leds/leds-lp3944.txt b/Documentation/leds/leds-lp3944.rst
index e88ac3b60c08..c2f87dc1a3a9 100644
--- a/Documentation/leds/leds-lp3944.txt
+++ b/Documentation/leds/leds-lp3944.rst
@@ -1,14 +1,20 @@
+====================
Kernel driver lp3944
====================
* National Semiconductor LP3944 Fun-light Chip
+
Prefix: 'lp3944'
+
Addresses scanned: None (see the Notes section below)
- Datasheet: Publicly available at the National Semiconductor website
- http://www.national.com/pf/LP/LP3944.html
+
+ Datasheet:
+
+ Publicly available at the National Semiconductor website
+ http://www.national.com/pf/LP/LP3944.html
Authors:
- Antonio Ospite <ospite@studenti.unina.it>
+ Antonio Ospite <ospite@studenti.unina.it>
Description
@@ -19,8 +25,11 @@ is used as a led controller.
The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
- - period: from 0s to 1.6s
- - duty cycle: percentage of the period the led is on, from 0 to 100
+
+ - period:
+ from 0s to 1.6s
+ - duty cycle:
+ percentage of the period the led is on, from 0 to 100
Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
See the datasheet for details.
@@ -35,7 +44,7 @@ The chip is used mainly in embedded contexts, so this driver expects it is
registered using the i2c_board_info mechanism.
To register the chip at address 0x60 on adapter 0, set the platform data
-according to include/linux/leds-lp3944.h, set the i2c board info:
+according to include/linux/leds-lp3944.h, set the i2c board info::
static struct i2c_board_info a910_i2c_board_info[] __initdata = {
{
@@ -44,7 +53,7 @@ according to include/linux/leds-lp3944.h, set the i2c board info:
},
};
-and register it in the platform init function
+and register it in the platform init function::
i2c_register_board_info(0, a910_i2c_board_info,
ARRAY_SIZE(a910_i2c_board_info));
diff --git a/Documentation/leds/leds-lp5521.rst b/Documentation/leds/leds-lp5521.rst
new file mode 100644
index 000000000000..0432615b083d
--- /dev/null
+++ b/Documentation/leds/leds-lp5521.rst
@@ -0,0 +1,115 @@
+========================
+Kernel driver for lp5521
+========================
+
+* National Semiconductor LP5521 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5521.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+
+LP5521 can drive up to 3 channels. Leds can be controlled directly via
+the led class control interface. Channels have generic names:
+lp5521:channelx, where x is 0 .. 2
+
+All three channels can be also controlled using the engine micro programs.
+More details of the instructions can be found from the public data sheet.
+
+LP5521 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode and enginex_load
+ Control interface for the engines:
+
+ x is 1 .. 3
+
+ enginex_mode:
+ disabled, load, run
+ enginex_load:
+ store program (visible only in engine load mode)
+
+ Example (start to blink the channel 2 led)::
+
+ cd /sys/class/leds/lp5521:channel2/device
+ echo "load" > engine3_mode
+ echo "037f4d0003ff6000" > engine3_load
+ echo "run" > engine3_mode
+
+ To stop the engine::
+
+ echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+sysfs contains a selftest entry.
+
+The test communicates with the chip and checks that
+the clock mode is automatically set to the requested one.
+
+Each channel has its own led current settings.
+
+- /sys/class/leds/lp5521:channel0/led_current - RW
+- /sys/class/leds/lp5521:channel0/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+example platform data::
+
+ static struct lp55xx_led_config lp5521_led_config[] = {
+ {
+ .name = "red",
+ .chan_nr = 0,
+ .led_current = 50,
+ .max_current = 130,
+ }, {
+ .name = "green",
+ .chan_nr = 1,
+ .led_current = 0,
+ .max_current = 130,
+ }, {
+ .name = "blue",
+ .chan_nr = 2,
+ .led_current = 0,
+ .max_current = 130,
+ }
+ };
+
+ static int lp5521_setup(void)
+ {
+ /* setup HW resources */
+ }
+
+ static void lp5521_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5521_enable(bool state)
+ {
+ /* Control of chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5521_platform_data = {
+ .led_config = lp5521_led_config,
+ .num_channels = ARRAY_SIZE(lp5521_led_config),
+ .clock_mode = LP55XX_CLOCK_EXT,
+ .setup_resources = lp5521_setup,
+ .release_resources = lp5521_release,
+ .enable = lp5521_enable,
+ };
+
+Note:
+ chan_nr can have values between 0 and 2.
+ The name of each channel can be configurable.
+ If the name field is not defined, the default name will be set to 'xxxx:channelN'
+ (XXXX : pdata->label or i2c client name, N : channel number)
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
diff --git a/Documentation/leds/leds-lp5521.txt b/Documentation/leds/leds-lp5521.txt
deleted file mode 100644
index d08d8c179f85..000000000000
--- a/Documentation/leds/leds-lp5521.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-Kernel driver for lp5521
-========================
-
-* National Semiconductor LP5521 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5521.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-
-LP5521 can drive up to 3 channels. Leds can be controlled directly via
-the led class control interface. Channels have generic names:
-lp5521:channelx, where x is 0 .. 2
-
-All three channels can be also controlled using the engine micro programs.
-More details of the instructions can be found from the public data sheet.
-
-LP5521 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode and enginex_load
- Control interface for the engines:
- x is 1 .. 3
- enginex_mode : disabled, load, run
- enginex_load : store program (visible only in engine load mode)
-
- Example (start to blink the channel 2 led):
- cd /sys/class/leds/lp5521:channel2/device
- echo "load" > engine3_mode
- echo "037f4d0003ff6000" > engine3_load
- echo "run" > engine3_mode
-
- To stop the engine:
- echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-sysfs contains a selftest entry.
-The test communicates with the chip and checks that
-the clock mode is automatically set to the requested one.
-
-Each channel has its own led current settings.
-/sys/class/leds/lp5521:channel0/led_current - RW
-/sys/class/leds/lp5521:channel0/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-example platform data:
-
-Note: chan_nr can have values between 0 and 2.
-The name of each channel can be configurable.
-If the name field is not defined, the default name will be set to 'xxxx:channelN'
-(XXXX : pdata->label or i2c client name, N : channel number)
-
-static struct lp55xx_led_config lp5521_led_config[] = {
- {
- .name = "red",
- .chan_nr = 0,
- .led_current = 50,
- .max_current = 130,
- }, {
- .name = "green",
- .chan_nr = 1,
- .led_current = 0,
- .max_current = 130,
- }, {
- .name = "blue",
- .chan_nr = 2,
- .led_current = 0,
- .max_current = 130,
- }
-};
-
-static int lp5521_setup(void)
-{
- /* setup HW resources */
-}
-
-static void lp5521_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5521_enable(bool state)
-{
- /* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5521_platform_data = {
- .led_config = lp5521_led_config,
- .num_channels = ARRAY_SIZE(lp5521_led_config),
- .clock_mode = LP55XX_CLOCK_EXT,
- .setup_resources = lp5521_setup,
- .release_resources = lp5521_release,
- .enable = lp5521_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.
diff --git a/Documentation/leds/leds-lp5523.rst b/Documentation/leds/leds-lp5523.rst
new file mode 100644
index 000000000000..7d7362a1dd57
--- /dev/null
+++ b/Documentation/leds/leds-lp5523.rst
@@ -0,0 +1,147 @@
+========================
+Kernel driver for lp5523
+========================
+
+* National Semiconductor LP5523 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5523.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+LP5523 can drive up to 9 channels. Leds can be controlled directly via
+the led class control interface.
+The name of each channel is configurable in the platform data - name and label.
+There are three options to make the channel name.
+
+a) Define the 'name' in the platform data
+
+To make specific channel name, then use 'name' platform data.
+
+- /sys/class/leds/R1 (name: 'R1')
+- /sys/class/leds/B1 (name: 'B1')
+
+b) Use the 'label' with no 'name' field
+
+For one device name with channel number, then use 'label'.
+- /sys/class/leds/RGB:channelN (label: 'RGB', N: 0 ~ 8)
+
+c) Default
+
+If both fields are NULL, 'lp5523' is used by default.
+- /sys/class/leds/lp5523:channelN (N: 0 ~ 8)
+
+LP5523 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode, enginex_load and enginex_leds
+
+ Control interface for the engines:
+
+ x is 1 .. 3
+
+ enginex_mode:
+ disabled, load, run
+ enginex_load:
+ microcode load
+ enginex_leds:
+ led mux control
+
+ ::
+
+ cd /sys/class/leds/lp5523:channel2/device
+ echo "load" > engine3_mode
+ echo "9d80400004ff05ff437f0000" > engine3_load
+ echo "111111111" > engine3_leds
+ echo "run" > engine3_mode
+
+ To stop the engine::
+
+ echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+LP5523 has three master faders. If a channel is mapped to one of
+the master faders, its output is dimmed based on the value of the master
+fader.
+
+For example::
+
+ echo "123000123" > master_fader_leds
+
+creates the following channel-fader mappings::
+
+ channel 0,6 to master_fader1
+ channel 1,7 to master_fader2
+ channel 2,8 to master_fader3
+
+Then, to have 25% of the original output on channel 0,6::
+
+ echo 64 > master_fader1
+
+To have 0% of the original output (i.e. no output) channel 1,7::
+
+ echo 0 > master_fader2
+
+To have 100% of the original output (i.e. no dimming) on channel 2,8::
+
+ echo 255 > master_fader3
+
+To clear all master fader controls::
+
+ echo "000000000" > master_fader_leds
+
+Selftest uses always the current from the platform data.
+
+Each channel contains led current settings.
+- /sys/class/leds/lp5523:channel2/led_current - RW
+- /sys/class/leds/lp5523:channel2/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+Example platform data::
+
+ static struct lp55xx_led_config lp5523_led_config[] = {
+ {
+ .name = "D1",
+ .chan_nr = 0,
+ .led_current = 50,
+ .max_current = 130,
+ },
+ ...
+ {
+ .chan_nr = 8,
+ .led_current = 50,
+ .max_current = 130,
+ }
+ };
+
+ static int lp5523_setup(void)
+ {
+ /* Setup HW resources */
+ }
+
+ static void lp5523_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5523_enable(bool state)
+ {
+ /* Control chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5523_platform_data = {
+ .led_config = lp5523_led_config,
+ .num_channels = ARRAY_SIZE(lp5523_led_config),
+ .clock_mode = LP55XX_CLOCK_EXT,
+ .setup_resources = lp5523_setup,
+ .release_resources = lp5523_release,
+ .enable = lp5523_enable,
+ };
+
+Note
+ chan_nr can have values between 0 and 8.
diff --git a/Documentation/leds/leds-lp5523.txt b/Documentation/leds/leds-lp5523.txt
deleted file mode 100644
index 0961a060fc4d..000000000000
--- a/Documentation/leds/leds-lp5523.txt
+++ /dev/null
@@ -1,130 +0,0 @@
-Kernel driver for lp5523
-========================
-
-* National Semiconductor LP5523 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5523.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-LP5523 can drive up to 9 channels. Leds can be controlled directly via
-the led class control interface.
-The name of each channel is configurable in the platform data - name and label.
-There are three options to make the channel name.
-
-a) Define the 'name' in the platform data
-To make specific channel name, then use 'name' platform data.
-/sys/class/leds/R1 (name: 'R1')
-/sys/class/leds/B1 (name: 'B1')
-
-b) Use the 'label' with no 'name' field
-For one device name with channel number, then use 'label'.
-/sys/class/leds/RGB:channelN (label: 'RGB', N: 0 ~ 8)
-
-c) Default
-If both fields are NULL, 'lp5523' is used by default.
-/sys/class/leds/lp5523:channelN (N: 0 ~ 8)
-
-LP5523 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode, enginex_load and enginex_leds
- Control interface for the engines:
- x is 1 .. 3
- enginex_mode : disabled, load, run
- enginex_load : microcode load
- enginex_leds : led mux control
-
- cd /sys/class/leds/lp5523:channel2/device
- echo "load" > engine3_mode
- echo "9d80400004ff05ff437f0000" > engine3_load
- echo "111111111" > engine3_leds
- echo "run" > engine3_mode
-
- To stop the engine:
- echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-LP5523 has three master faders. If a channel is mapped to one of
-the master faders, its output is dimmed based on the value of the master
-fader.
-
-For example,
-
- echo "123000123" > master_fader_leds
-
-creates the following channel-fader mappings:
-
- channel 0,6 to master_fader1
- channel 1,7 to master_fader2
- channel 2,8 to master_fader3
-
-Then, to have 25% of the original output on channel 0,6:
-
- echo 64 > master_fader1
-
-To have 0% of the original output (i.e. no output) channel 1,7:
-
- echo 0 > master_fader2
-
-To have 100% of the original output (i.e. no dimming) on channel 2,8:
-
- echo 255 > master_fader3
-
-To clear all master fader controls:
-
- echo "000000000" > master_fader_leds
-
-Selftest uses always the current from the platform data.
-
-Each channel contains led current settings.
-/sys/class/leds/lp5523:channel2/led_current - RW
-/sys/class/leds/lp5523:channel2/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-Example platform data:
-
-Note - chan_nr can have values between 0 and 8.
-
-static struct lp55xx_led_config lp5523_led_config[] = {
- {
- .name = "D1",
- .chan_nr = 0,
- .led_current = 50,
- .max_current = 130,
- },
-...
- {
- .chan_nr = 8,
- .led_current = 50,
- .max_current = 130,
- }
-};
-
-static int lp5523_setup(void)
-{
- /* Setup HW resources */
-}
-
-static void lp5523_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5523_enable(bool state)
-{
- /* Control chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5523_platform_data = {
- .led_config = lp5523_led_config,
- .num_channels = ARRAY_SIZE(lp5523_led_config),
- .clock_mode = LP55XX_CLOCK_EXT,
- .setup_resources = lp5523_setup,
- .release_resources = lp5523_release,
- .enable = lp5523_enable,
-};
diff --git a/Documentation/leds/leds-lp5562.rst b/Documentation/leds/leds-lp5562.rst
new file mode 100644
index 000000000000..79bbb2487ff6
--- /dev/null
+++ b/Documentation/leds/leds-lp5562.rst
@@ -0,0 +1,137 @@
+========================
+Kernel driver for lp5562
+========================
+
+* TI LP5562 LED Driver
+
+Author: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+===========
+
+ LP5562 can drive up to 4 channels. R/G/B and White.
+ LEDs can be controlled directly via the led class control interface.
+
+ All four channels can be also controlled using the engine micro programs.
+ LP5562 has the internal program memory for running various LED patterns.
+ For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+Device attribute
+================
+
+engine_mux
+ 3 Engines are allocated in LP5562, but the number of channel is 4.
+ Therefore each channel should be mapped to the engine number.
+
+ Value: RGB or W
+
+ This attribute is used for programming LED data with the firmware interface.
+ Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
+ so additional sysfs is required
+
+ LED Map
+
+ ===== === ===============================
+ Red ... Engine 1 (fixed)
+ Green ... Engine 2 (fixed)
+ Blue ... Engine 3 (fixed)
+ White ... Engine 1 or 2 or 3 (selective)
+ ===== === ===============================
+
+How to load the program data using engine_mux
+=============================================
+
+ Before loading the LP5562 program data, engine_mux should be written between
+ the engine selection and loading the firmware.
+ Engine mux has two different mode, RGB and W.
+ RGB is used for loading RGB program data, W is used for W program data.
+
+ For example, run blinking green channel pattern::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine # 2 is for green channel
+ echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux # engine mux for RGB
+ echo 1 > /sys/class/firmware/lp5562/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+ echo 0 > /sys/class/firmware/lp5562/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+ To run a blinking white pattern::
+
+ echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
+ echo 1 > /sys/class/firmware/lp5562/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+ echo 0 > /sys/class/firmware/lp5562/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+How to load the predefined patterns
+===================================
+
+ Please refer to 'leds-lp55xx.txt"
+
+Setting Current of Each Channel
+===============================
+
+ Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
+ The 'led_current' and 'max_current' are used.
+
+Example of Platform data
+========================
+
+::
+
+ static struct lp55xx_led_config lp5562_led_config[] = {
+ {
+ .name = "R",
+ .chan_nr = 0,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "G",
+ .chan_nr = 1,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "B",
+ .chan_nr = 2,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "W",
+ .chan_nr = 3,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ };
+
+ static int lp5562_setup(void)
+ {
+ /* setup HW resources */
+ }
+
+ static void lp5562_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5562_enable(bool state)
+ {
+ /* Control of chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5562_platform_data = {
+ .led_config = lp5562_led_config,
+ .num_channels = ARRAY_SIZE(lp5562_led_config),
+ .setup_resources = lp5562_setup,
+ .release_resources = lp5562_release,
+ .enable = lp5562_enable,
+ };
+
+To configure the platform specific data, lp55xx_platform_data structure is used
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
diff --git a/Documentation/leds/leds-lp5562.txt b/Documentation/leds/leds-lp5562.txt
deleted file mode 100644
index 5a823ff6b393..000000000000
--- a/Documentation/leds/leds-lp5562.txt
+++ /dev/null
@@ -1,120 +0,0 @@
-Kernel driver for LP5562
-========================
-
-* TI LP5562 LED Driver
-
-Author: Milo(Woogyom) Kim <milo.kim@ti.com>
-
-Description
-
- LP5562 can drive up to 4 channels. R/G/B and White.
- LEDs can be controlled directly via the led class control interface.
-
- All four channels can be also controlled using the engine micro programs.
- LP5562 has the internal program memory for running various LED patterns.
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-Device attribute: engine_mux
-
- 3 Engines are allocated in LP5562, but the number of channel is 4.
- Therefore each channel should be mapped to the engine number.
- Value : RGB or W
-
- This attribute is used for programming LED data with the firmware interface.
- Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
- so additional sysfs is required.
-
- LED Map
- Red ... Engine 1 (fixed)
- Green ... Engine 2 (fixed)
- Blue ... Engine 3 (fixed)
- White ... Engine 1 or 2 or 3 (selective)
-
-How to load the program data using engine_mux
-
- Before loading the LP5562 program data, engine_mux should be written between
- the engine selection and loading the firmware.
- Engine mux has two different mode, RGB and W.
- RGB is used for loading RGB program data, W is used for W program data.
-
- For example, run blinking green channel pattern,
- echo 2 > /sys/bus/i2c/devices/xxxx/select_engine # 2 is for green channel
- echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux # engine mux for RGB
- echo 1 > /sys/class/firmware/lp5562/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
- echo 0 > /sys/class/firmware/lp5562/loading
- echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
- To run a blinking white pattern,
- echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
- echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
- echo 1 > /sys/class/firmware/lp5562/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
- echo 0 > /sys/class/firmware/lp5562/loading
- echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-How to load the predefined patterns
-
- Please refer to 'leds-lp55xx.txt"
-
-Setting Current of Each Channel
-
- Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
- The 'led_current' and 'max_current' are used.
-
-(Example of Platform data)
-
-To configure the platform specific data, lp55xx_platform_data structure is used.
-
-static struct lp55xx_led_config lp5562_led_config[] = {
- {
- .name = "R",
- .chan_nr = 0,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "G",
- .chan_nr = 1,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "B",
- .chan_nr = 2,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "W",
- .chan_nr = 3,
- .led_current = 20,
- .max_current = 40,
- },
-};
-
-static int lp5562_setup(void)
-{
- /* setup HW resources */
-}
-
-static void lp5562_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5562_enable(bool state)
-{
- /* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5562_platform_data = {
- .led_config = lp5562_led_config,
- .num_channels = ARRAY_SIZE(lp5562_led_config),
- .setup_resources = lp5562_setup,
- .release_resources = lp5562_release,
- .enable = lp5562_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.
diff --git a/Documentation/leds/leds-lp55xx.rst b/Documentation/leds/leds-lp55xx.rst
new file mode 100644
index 000000000000..632e41cec0b5
--- /dev/null
+++ b/Documentation/leds/leds-lp55xx.rst
@@ -0,0 +1,224 @@
+=================================================
+LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
+=================================================
+
+Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+-----------
+LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
+
+ Register access via the I2C
+ Device initialization/deinitialization
+ Create LED class devices for multiple output channels
+ Device attributes for user-space interface
+ Program memory for running LED patterns
+
+The LP55xx common driver provides these features using exported functions.
+
+ lp55xx_init_device() / lp55xx_deinit_device()
+ lp55xx_register_leds() / lp55xx_unregister_leds()
+ lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
+
+( Driver Structure Data )
+
+In lp55xx common driver, two different data structure is used.
+
+* lp55xx_led
+ control multi output LED channels such as led current, channel index.
+* lp55xx_chip
+ general chip control such like the I2C and platform data.
+
+For example, LP5521 has maximum 3 LED channels.
+LP5523/55231 has 9 output channels::
+
+ lp55xx_chip for LP5521 ... lp55xx_led #1
+ lp55xx_led #2
+ lp55xx_led #3
+
+ lp55xx_chip for LP5523 ... lp55xx_led #1
+ lp55xx_led #2
+ .
+ .
+ lp55xx_led #9
+
+( Chip Dependent Code )
+
+To support device specific configurations, special structure
+'lpxx_device_config' is used.
+
+ - Maximum number of channels
+ - Reset command, chip enable command
+ - Chip specific initialization
+ - Brightness control register access
+ - Setting LED output current
+ - Program memory address access for running patterns
+ - Additional device specific attributes
+
+( Firmware Interface )
+
+LP55xx family devices have the internal program memory for running
+various LED patterns.
+
+This pattern data is saved as a file in the user-land or
+hex byte string is written into the memory through the I2C.
+
+LP55xx common driver supports the firmware interface.
+
+LP55xx chips have three program engines.
+
+To load and run the pattern, the programming sequence is following.
+
+ (1) Select an engine number (1/2/3)
+ (2) Mode change to load
+ (3) Write pattern data into selected area
+ (4) Mode change to run
+
+The LP55xx common driver provides simple interfaces as below.
+
+select_engine:
+ Select which engine is used for running program
+run_engine:
+ Start program which is loaded via the firmware interface
+firmware:
+ Load program data
+
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
+For example, run blinking pattern in engine #1 of LP5521::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp5521/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+ echo 0 > /sys/class/firmware/lp5521/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+For example, run blinking pattern in engine #3 of LP55231
+
+Two LEDs are configured as pattern output channels::
+
+ echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp55231/loading
+ echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
+ echo 0 > /sys/class/firmware/lp55231/loading
+ echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+To start blinking patterns in engine #2 and #3 simultaneously::
+
+ for idx in 2 3
+ do
+ echo $idx > /sys/class/leds/red/device/select_engine
+ sleep 0.1
+ echo 1 > /sys/class/firmware/lp5521/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+ echo 0 > /sys/class/firmware/lp5521/loading
+ done
+ echo 1 > /sys/class/leds/red/device/run_engine
+
+Here is another example for LP5523.
+
+Full LED strings are selected by 'engine2_leds'::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp5523/loading
+ echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
+ echo 0 > /sys/class/firmware/lp5523/loading
+ echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+As soon as 'loading' is set to 0, registered callback is called.
+Inside the callback, the selected engine is loaded and memory is updated.
+To run programmed pattern, 'run_engine' attribute should be enabled.
+
+The pattern sequence of LP8501 is similar to LP5523.
+
+However pattern data is specific.
+
+Ex 1) Engine 1 is used::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+Ex 2) Engine 2 and 3 are used at the same time::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+ sleep 1
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ sleep 1
+ echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ sleep 1
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ sleep 1
+ echo 1 > /sys/class/leds/d1/device/run_engine
+
+( 'run_engine' and 'firmware_cb' )
+
+The sequence of running the program data is common.
+
+But each device has own specific register addresses for commands.
+
+To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
+
+run_engine:
+ Control the selected engine
+firmware_cb:
+ The callback function after loading the firmware is done.
+
+ Chip specific commands for loading and updating program memory.
+
+( Predefined pattern data )
+
+Without the firmware interface, LP55xx driver provides another method for
+loading a LED pattern. That is 'predefined' pattern.
+
+A predefined pattern is defined in the platform data and load it(or them)
+via the sysfs if needed.
+
+To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
+configured.
+
+Example of predefined pattern data::
+
+ /* mode_1: blinking data */
+ static const u8 mode_1[] = {
+ 0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
+ };
+
+ /* mode_2: always on */
+ static const u8 mode_2[] = { 0x40, 0xFF, };
+
+ struct lp55xx_predef_pattern board_led_patterns[] = {
+ {
+ .r = mode_1,
+ .size_r = ARRAY_SIZE(mode_1),
+ },
+ {
+ .b = mode_2,
+ .size_b = ARRAY_SIZE(mode_2),
+ },
+ }
+
+ struct lp55xx_platform_data lp5562_pdata = {
+ ...
+ .patterns = board_led_patterns,
+ .num_patterns = ARRAY_SIZE(board_led_patterns),
+ };
+
+Then, mode_1 and mode_2 can be run via through the sysfs::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
+ echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern # blue LED always on
+
+To stop running pattern::
+
+ echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern
diff --git a/Documentation/leds/leds-lp55xx.txt b/Documentation/leds/leds-lp55xx.txt
deleted file mode 100644
index e23fa91ea722..000000000000
--- a/Documentation/leds/leds-lp55xx.txt
+++ /dev/null
@@ -1,194 +0,0 @@
-LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
-=================================================
-
-Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
-
-Description
------------
-LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
-
- Register access via the I2C
- Device initialization/deinitialization
- Create LED class devices for multiple output channels
- Device attributes for user-space interface
- Program memory for running LED patterns
-
-The LP55xx common driver provides these features using exported functions.
- lp55xx_init_device() / lp55xx_deinit_device()
- lp55xx_register_leds() / lp55xx_unregister_leds()
- lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
-
-( Driver Structure Data )
-
-In lp55xx common driver, two different data structure is used.
-
-o lp55xx_led
- control multi output LED channels such as led current, channel index.
-o lp55xx_chip
- general chip control such like the I2C and platform data.
-
-For example, LP5521 has maximum 3 LED channels.
-LP5523/55231 has 9 output channels.
-
-lp55xx_chip for LP5521 ... lp55xx_led #1
- lp55xx_led #2
- lp55xx_led #3
-
-lp55xx_chip for LP5523 ... lp55xx_led #1
- lp55xx_led #2
- .
- .
- lp55xx_led #9
-
-( Chip Dependent Code )
-
-To support device specific configurations, special structure
-'lpxx_device_config' is used.
-
- Maximum number of channels
- Reset command, chip enable command
- Chip specific initialization
- Brightness control register access
- Setting LED output current
- Program memory address access for running patterns
- Additional device specific attributes
-
-( Firmware Interface )
-
-LP55xx family devices have the internal program memory for running
-various LED patterns.
-This pattern data is saved as a file in the user-land or
-hex byte string is written into the memory through the I2C.
-LP55xx common driver supports the firmware interface.
-
-LP55xx chips have three program engines.
-To load and run the pattern, the programming sequence is following.
- (1) Select an engine number (1/2/3)
- (2) Mode change to load
- (3) Write pattern data into selected area
- (4) Mode change to run
-
-The LP55xx common driver provides simple interfaces as below.
-select_engine : Select which engine is used for running program
-run_engine : Start program which is loaded via the firmware interface
-firmware : Load program data
-
-In case of LP5523, one more command is required, 'enginex_leds'.
-It is used for selecting LED output(s) at each engine number.
-In more details, please refer to 'leds-lp5523.txt'.
-
-For example, run blinking pattern in engine #1 of LP5521
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5521/loading
-echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
-echo 0 > /sys/class/firmware/lp5521/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-For example, run blinking pattern in engine #3 of LP55231
-Two LEDs are configured as pattern output channels.
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp55231/loading
-echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
-echo 0 > /sys/class/firmware/lp55231/loading
-echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-To start blinking patterns in engine #2 and #3 simultaneously,
-for idx in 2 3
-do
- echo $idx > /sys/class/leds/red/device/select_engine
- sleep 0.1
- echo 1 > /sys/class/firmware/lp5521/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
- echo 0 > /sys/class/firmware/lp5521/loading
-done
-echo 1 > /sys/class/leds/red/device/run_engine
-
-Here is another example for LP5523.
-Full LED strings are selected by 'engine2_leds'.
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5523/loading
-echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
-echo 0 > /sys/class/firmware/lp5523/loading
-echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-As soon as 'loading' is set to 0, registered callback is called.
-Inside the callback, the selected engine is loaded and memory is updated.
-To run programmed pattern, 'run_engine' attribute should be enabled.
-
-The pattern sequence of LP8501 is similar to LP5523.
-However pattern data is specific.
-Ex 1) Engine 1 is used
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-Ex 2) Engine 2 and 3 are used at the same time
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 1 > /sys/class/leds/d1/device/run_engine
-
-( 'run_engine' and 'firmware_cb' )
-The sequence of running the program data is common.
-But each device has own specific register addresses for commands.
-To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
-run_engine : Control the selected engine
-firmware_cb : The callback function after loading the firmware is done.
- Chip specific commands for loading and updating program memory.
-
-( Predefined pattern data )
-
-Without the firmware interface, LP55xx driver provides another method for
-loading a LED pattern. That is 'predefined' pattern.
-A predefined pattern is defined in the platform data and load it(or them)
-via the sysfs if needed.
-To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
-configured.
-
- Example of predefined pattern data:
-
- /* mode_1: blinking data */
- static const u8 mode_1[] = {
- 0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
- };
-
- /* mode_2: always on */
- static const u8 mode_2[] = { 0x40, 0xFF, };
-
- struct lp55xx_predef_pattern board_led_patterns[] = {
- {
- .r = mode_1,
- .size_r = ARRAY_SIZE(mode_1),
- },
- {
- .b = mode_2,
- .size_b = ARRAY_SIZE(mode_2),
- },
- }
-
- struct lp55xx_platform_data lp5562_pdata = {
- ...
- .patterns = board_led_patterns,
- .num_patterns = ARRAY_SIZE(board_led_patterns),
- };
-
-Then, mode_1 and mode_2 can be run via through the sysfs.
-
- echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
- echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern # blue LED always on
-
-To stop running pattern,
- echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern
diff --git a/Documentation/leds/leds-mlxcpld.rst b/Documentation/leds/leds-mlxcpld.rst
new file mode 100644
index 000000000000..528582429e0b
--- /dev/null
+++ b/Documentation/leds/leds-mlxcpld.rst
@@ -0,0 +1,118 @@
+=======================================
+Kernel driver for Mellanox systems LEDs
+=======================================
+
+Provide system LED support for the nex Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+"msn2410", "msb7800", "msn2740", "msn2100".
+
+Description
+-----------
+Driver provides the following LEDs for the systems "msx6710", "msx6720",
+"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
+
+ - mlxcpld:fan1:green
+ - mlxcpld:fan1:red
+ - mlxcpld:fan2:green
+ - mlxcpld:fan2:red
+ - mlxcpld:fan3:green
+ - mlxcpld:fan3:red
+ - mlxcpld:fan4:green
+ - mlxcpld:fan4:red
+ - mlxcpld:psu:green
+ - mlxcpld:psu:red
+ - mlxcpld:status:green
+ - mlxcpld:status:red
+
+ "status"
+ - CPLD reg offset: 0x20
+ - Bits [3:0]
+
+ "psu"
+ - CPLD reg offset: 0x20
+ - Bits [7:4]
+
+ "fan1"
+ - CPLD reg offset: 0x21
+ - Bits [3:0]
+
+ "fan2"
+ - CPLD reg offset: 0x21
+ - Bits [7:4]
+
+ "fan3"
+ - CPLD reg offset: 0x22
+ - Bits [3:0]
+
+ "fan4"
+ - CPLD reg offset: 0x22
+ - Bits [7:4]
+
+ Color mask for all the above LEDs:
+
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+
+ - [0,0,0,0] = LED OFF
+ - [0,1,0,1] = Red static ON
+ - [1,1,0,1] = Green static ON
+ - [0,1,1,0] = Red blink 3Hz
+ - [1,1,1,0] = Green blink 3Hz
+ - [0,1,1,1] = Red blink 6Hz
+ - [1,1,1,1] = Green blink 6Hz
+
+Driver provides the following LEDs for the system "msn2100":
+
+ - mlxcpld:fan:green
+ - mlxcpld:fan:red
+ - mlxcpld:psu1:green
+ - mlxcpld:psu1:red
+ - mlxcpld:psu2:green
+ - mlxcpld:psu2:red
+ - mlxcpld:status:green
+ - mlxcpld:status:red
+ - mlxcpld:uid:blue
+
+ "status"
+ - CPLD reg offset: 0x20
+ - Bits [3:0]
+
+ "fan"
+ - CPLD reg offset: 0x21
+ - Bits [3:0]
+
+ "psu1"
+ - CPLD reg offset: 0x23
+ - Bits [3:0]
+
+ "psu2"
+ - CPLD reg offset: 0x23
+ - Bits [7:4]
+
+ "uid"
+ - CPLD reg offset: 0x24
+ - Bits [3:0]
+
+ Color mask for all the above LEDs, excepted uid:
+
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+
+ - [0,0,0,0] = LED OFF
+ - [0,1,0,1] = Red static ON
+ - [1,1,0,1] = Green static ON
+ - [0,1,1,0] = Red blink 3Hz
+ - [1,1,1,0] = Green blink 3Hz
+ - [0,1,1,1] = Red blink 6Hz
+ - [1,1,1,1] = Green blink 6Hz
+
+ Color mask for uid LED:
+ [bit3,bit2,bit1,bit0]:
+
+ - [0,0,0,0] = LED OFF
+ - [1,1,0,1] = Blue static ON
+ - [1,1,1,0] = Blue blink 3Hz
+ - [1,1,1,1] = Blue blink 6Hz
+
+Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
+For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
diff --git a/Documentation/leds/leds-mlxcpld.txt b/Documentation/leds/leds-mlxcpld.txt
deleted file mode 100644
index a0e8fd457117..000000000000
--- a/Documentation/leds/leds-mlxcpld.txt
+++ /dev/null
@@ -1,110 +0,0 @@
-Kernel driver for Mellanox systems LEDs
-=======================================
-
-Provide system LED support for the nex Mellanox systems:
-"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
-"msn2410", "msb7800", "msn2740", "msn2100".
-
-Description
------------
-Driver provides the following LEDs for the systems "msx6710", "msx6720",
-"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
- mlxcpld:fan1:green
- mlxcpld:fan1:red
- mlxcpld:fan2:green
- mlxcpld:fan2:red
- mlxcpld:fan3:green
- mlxcpld:fan3:red
- mlxcpld:fan4:green
- mlxcpld:fan4:red
- mlxcpld:psu:green
- mlxcpld:psu:red
- mlxcpld:status:green
- mlxcpld:status:red
-
- "status"
- CPLD reg offset: 0x20
- Bits [3:0]
-
- "psu"
- CPLD reg offset: 0x20
- Bits [7:4]
-
- "fan1"
- CPLD reg offset: 0x21
- Bits [3:0]
-
- "fan2"
- CPLD reg offset: 0x21
- Bits [7:4]
-
- "fan3"
- CPLD reg offset: 0x22
- Bits [3:0]
-
- "fan4"
- CPLD reg offset: 0x22
- Bits [7:4]
-
- Color mask for all the above LEDs:
- [bit3,bit2,bit1,bit0] or
- [bit7,bit6,bit5,bit4]:
- [0,0,0,0] = LED OFF
- [0,1,0,1] = Red static ON
- [1,1,0,1] = Green static ON
- [0,1,1,0] = Red blink 3Hz
- [1,1,1,0] = Green blink 3Hz
- [0,1,1,1] = Red blink 6Hz
- [1,1,1,1] = Green blink 6Hz
-
-Driver provides the following LEDs for the system "msn2100":
- mlxcpld:fan:green
- mlxcpld:fan:red
- mlxcpld:psu1:green
- mlxcpld:psu1:red
- mlxcpld:psu2:green
- mlxcpld:psu2:red
- mlxcpld:status:green
- mlxcpld:status:red
- mlxcpld:uid:blue
-
- "status"
- CPLD reg offset: 0x20
- Bits [3:0]
-
- "fan"
- CPLD reg offset: 0x21
- Bits [3:0]
-
- "psu1"
- CPLD reg offset: 0x23
- Bits [3:0]
-
- "psu2"
- CPLD reg offset: 0x23
- Bits [7:4]
-
- "uid"
- CPLD reg offset: 0x24
- Bits [3:0]
-
- Color mask for all the above LEDs, excepted uid:
- [bit3,bit2,bit1,bit0] or
- [bit7,bit6,bit5,bit4]:
- [0,0,0,0] = LED OFF
- [0,1,0,1] = Red static ON
- [1,1,0,1] = Green static ON
- [0,1,1,0] = Red blink 3Hz
- [1,1,1,0] = Green blink 3Hz
- [0,1,1,1] = Red blink 6Hz
- [1,1,1,1] = Green blink 6Hz
-
- Color mask for uid LED:
- [bit3,bit2,bit1,bit0]:
- [0,0,0,0] = LED OFF
- [1,1,0,1] = Blue static ON
- [1,1,1,0] = Blue blink 3Hz
- [1,1,1,1] = Blue blink 6Hz
-
-Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
-For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
diff --git a/Documentation/leds/ledtrig-oneshot.txt b/Documentation/leds/ledtrig-oneshot.rst
index fe57474a12e2..69fa3ea1d554 100644
--- a/Documentation/leds/ledtrig-oneshot.txt
+++ b/Documentation/leds/ledtrig-oneshot.rst
@@ -1,3 +1,4 @@
+====================
One-shot LED Trigger
====================
@@ -17,27 +18,27 @@ additional "invert" property specifies if the LED has to stay off (normal) or
on (inverted) when not rearmed.
The trigger can be activated from user space on led class devices as shown
-below:
+below::
echo oneshot > trigger
This adds sysfs attributes to the LED that are documented in:
Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
-Example use-case: network devices, initialization:
+Example use-case: network devices, initialization::
echo oneshot > trigger # set trigger for this led
echo 33 > delay_on # blink at 1 / (33 + 33) Hz on continuous traffic
echo 33 > delay_off
-interface goes up:
+interface goes up::
echo 1 > invert # set led as normally-on, turn the led on
-packet received/transmitted:
+packet received/transmitted::
echo 1 > shot # led starts blinking, ignored if already blinking
-interface goes down
+interface goes down::
echo 0 > invert # set led as normally-off, turn the led off
diff --git a/Documentation/leds/ledtrig-transient.txt b/Documentation/leds/ledtrig-transient.rst
index 3bd38b487df1..d921dc830cd0 100644
--- a/Documentation/leds/ledtrig-transient.txt
+++ b/Documentation/leds/ledtrig-transient.rst
@@ -1,3 +1,4 @@
+=====================
LED Transient Trigger
=====================
@@ -62,12 +63,13 @@ non-transient state. When driver gets suspended, irrespective of the transient
state, the LED state changes to LED_OFF.
Transient trigger can be enabled and disabled from user space on led class
-devices, that support this trigger as shown below:
+devices, that support this trigger as shown below::
-echo transient > trigger
-echo none > trigger
+ echo transient > trigger
+ echo none > trigger
-NOTE: Add a new property trigger state to control the state.
+NOTE:
+ Add a new property trigger state to control the state.
This trigger exports three properties, activate, state, and duration. When
transient trigger is activated these properties are set to default values.
@@ -79,7 +81,8 @@ transient trigger is activated these properties are set to default values.
- state allows user to specify a transient state to be held for the specified
duration.
- activate - one shot timer activate mechanism.
+ activate
+ - one shot timer activate mechanism.
1 when activated, 0 when deactivated.
default value is zero when transient trigger is enabled,
to allow duration to be set.
@@ -89,12 +92,14 @@ transient trigger is activated these properties are set to default values.
deactivated state indicates that there is no active timer
running.
- duration - one shot timer value. When activate is set, duration value
+ duration
+ - one shot timer value. When activate is set, duration value
is used to start a timer that runs once. This value doesn't
get changed by the trigger unless user does a set via
echo new_value > duration
- state - transient state to be held. It has two values 0 or 1. 0 maps
+ state
+ - transient state to be held. It has two values 0 or 1. 0 maps
to LED_OFF and 1 maps to LED_FULL. The specified state is
held for the duration of the one shot timer and then the
state gets changed to the non-transient state which is the
@@ -114,39 +119,49 @@ When timer expires activate goes back to deactivated state, duration is left
at the set value to be used when activate is set at a future time. This will
allow user app to set the time once and activate it to run it once for the
specified value as needed. When timer expires, state is restored to the
-non-transient state which is the inverse of the transient state.
-
- echo 1 > activate - starts timer = duration when duration is not 0.
- echo 0 > activate - cancels currently running timer.
- echo n > duration - stores timer value to be used upon next
- activate. Currently active timer if
- any, continues to run for the specified time.
- echo 0 > duration - stores timer value to be used upon next
- activate. Currently active timer if any,
- continues to run for the specified time.
- echo 1 > state - stores desired transient state LED_FULL to be
+non-transient state which is the inverse of the transient state:
+
+ ================= ===============================================
+ echo 1 > activate starts timer = duration when duration is not 0.
+ echo 0 > activate cancels currently running timer.
+ echo n > duration stores timer value to be used upon next
+ activate. Currently active timer if
+ any, continues to run for the specified time.
+ echo 0 > duration stores timer value to be used upon next
+ activate. Currently active timer if any,
+ continues to run for the specified time.
+ echo 1 > state stores desired transient state LED_FULL to be
held for the specified duration.
- echo 0 > state - stores desired transient state LED_OFF to be
+ echo 0 > state stores desired transient state LED_OFF to be
held for the specified duration.
+ ================= ===============================================
+
+What is not supported
+=====================
-What is not supported:
-======================
- Timer activation is one shot and extending and/or shortening the timer
is not supported.
-Example use-case 1:
+Examples
+========
+
+use-case 1::
+
echo transient > trigger
echo n > duration
echo 1 > state
-repeat the following step as needed:
+
+repeat the following step as needed::
+
echo 1 > activate - start timer = duration to run once
echo 1 > activate - start timer = duration to run once
echo none > trigger
This trigger is intended to be used for for the following example use cases:
+
- Control of vibrate (phones, tablets etc.) hardware by user space app.
- Use of LED by user space app as activity indicator.
- Use of LED by user space app as a kind of watchdog indicator -- as
- long as the app is alive, it can keep the LED illuminated, if it dies
- the LED will be extinguished automatically.
+ long as the app is alive, it can keep the LED illuminated, if it dies
+ the LED will be extinguished automatically.
- Use by any user space app that needs a transient GPIO output.
diff --git a/Documentation/leds/ledtrig-usbport.txt b/Documentation/leds/ledtrig-usbport.rst
index 69f54bfb4789..37c2505bfd57 100644
--- a/Documentation/leds/ledtrig-usbport.txt
+++ b/Documentation/leds/ledtrig-usbport.rst
@@ -1,3 +1,4 @@
+====================
USB port LED trigger
====================
@@ -10,14 +11,18 @@ listed as separated entries in a "ports" subdirectory. Selecting is handled by
echoing "1" to a chosen port.
Please note that this trigger allows selecting multiple USB ports for a single
-LED. This can be useful in two cases:
+LED.
+
+This can be useful in two cases:
1) Device with single USB LED and few physical ports
+====================================================
In such a case LED will be turned on as long as there is at least one connected
USB device.
2) Device with a physical port handled by few controllers
+=========================================================
Some devices may have one controller per PHY standard. E.g. USB 3.0 physical
port may be handled by ohci-platform, ehci-platform and xhci-hcd. If there is
@@ -25,14 +30,14 @@ only one LED user will most likely want to assign ports from all 3 hubs.
This trigger can be activated from user space on led class devices as shown
-below:
+below::
echo usbport > trigger
This adds sysfs attributes to the LED that are documented in:
Documentation/ABI/testing/sysfs-class-led-trigger-usbport
-Example use-case:
+Example use-case::
echo usbport > trigger
echo 1 > ports/usb1-port1
diff --git a/Documentation/leds/uleds.txt b/Documentation/leds/uleds.rst
index 13e375a580f9..83221098009c 100644
--- a/Documentation/leds/uleds.txt
+++ b/Documentation/leds/uleds.rst
@@ -1,3 +1,4 @@
+==============
Userspace LEDs
==============
@@ -10,12 +11,12 @@ Usage
When the driver is loaded, a character device is created at /dev/uleds. To
create a new LED class device, open /dev/uleds and write a uleds_user_dev
-structure to it (found in kernel public header file linux/uleds.h).
+structure to it (found in kernel public header file linux/uleds.h)::
#define LED_MAX_NAME_SIZE 64
struct uleds_user_dev {
- char name[LED_MAX_NAME_SIZE];
+ char name[LED_MAX_NAME_SIZE];
};
A new LED class device will be created with the name given. The name can be
diff --git a/MAINTAINERS b/MAINTAINERS
index 558acf24ea1e..e61476a388b1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10165,7 +10165,7 @@ L: linux-leds@vger.kernel.org
S: Supported
F: drivers/leds/leds-mlxcpld.c
F: drivers/leds/leds-mlxreg.c
-F: Documentation/leds/leds-mlxcpld.txt
+F: Documentation/leds/leds-mlxcpld.rst
MELLANOX PLATFORM DRIVER
M: Vadim Pasternak <vadimp@mellanox.com>
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 760f73a49c9f..b0fdeef10bd9 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -784,6 +784,41 @@ config LEDS_NIC78BX
To compile this driver as a module, choose M here: the module
will be called leds-nic78bx.
+config LEDS_SPI_BYTE
+ tristate "LED support for SPI LED controller with a single byte"
+ depends on LEDS_CLASS
+ depends on SPI
+ depends on OF
+ help
+ This option enables support for LED controller which use a single byte
+ for controlling the brightness. Currently the following controller is
+ supported: Ubiquiti airCube ISP microcontroller based LED controller.
+
+config LEDS_TI_LMU_COMMON
+ tristate "LED driver for TI LMU"
+ depends on LEDS_CLASS
+ depends on REGMAP
+ help
+ Say Y to enable the LED driver for TI LMU devices.
+ This supports common features between the TI LM3532, LM3631, LM3632,
+ LM3633, LM3695 and LM3697.
+
+config LEDS_LM3697
+ tristate "LED driver for LM3697"
+ depends on LEDS_TI_LMU_COMMON
+ depends on I2C && OF
+ help
+ Say Y to enable the LM3697 LED driver for TI LMU devices.
+ This supports the LED device LM3697.
+
+config LEDS_LM36274
+ tristate "LED driver for LM36274"
+ depends on LEDS_TI_LMU_COMMON
+ depends on MFD_TI_LMU
+ help
+ Say Y to enable the LM36274 LED driver for TI LMU devices.
+ This supports the LED device LM36274.
+
comment "LED Triggers"
source "drivers/leds/trigger/Kconfig"
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 1e9702ebffee..41fb073a39c1 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -77,10 +77,14 @@ obj-$(CONFIG_LEDS_PM8058) += leds-pm8058.o
obj-$(CONFIG_LEDS_MLXCPLD) += leds-mlxcpld.o
obj-$(CONFIG_LEDS_MLXREG) += leds-mlxreg.o
obj-$(CONFIG_LEDS_NIC78BX) += leds-nic78bx.o
+obj-$(CONFIG_LEDS_SPI_BYTE) += leds-spi-byte.o
obj-$(CONFIG_LEDS_MT6323) += leds-mt6323.o
obj-$(CONFIG_LEDS_LM3692X) += leds-lm3692x.o
obj-$(CONFIG_LEDS_SC27XX_BLTC) += leds-sc27xx-bltc.o
obj-$(CONFIG_LEDS_LM3601X) += leds-lm3601x.o
+obj-$(CONFIG_LEDS_TI_LMU_COMMON) += leds-ti-lmu-common.o
+obj-$(CONFIG_LEDS_LM3697) += leds-lm3697.o
+obj-$(CONFIG_LEDS_LM36274) += leds-lm36274.o
# LED SPI Drivers
obj-$(CONFIG_LEDS_CR0014114) += leds-cr0014114.o
diff --git a/drivers/leds/leds-lm36274.c b/drivers/leds/leds-lm36274.c
new file mode 100644
index 000000000000..ed9dc857ec8f
--- /dev/null
+++ b/drivers/leds/leds-lm36274.c
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LM36274 LED chip family driver
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/leds.h>
+#include <linux/leds-ti-lmu-common.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/ti-lmu.h>
+#include <linux/mfd/ti-lmu-register.h>
+
+#include <uapi/linux/uleds.h>
+
+#define LM36274_MAX_STRINGS 4
+#define LM36274_BL_EN BIT(4)
+
+/**
+ * struct lm36274
+ * @pdev: platform device
+ * @led_dev: led class device
+ * @lmu_data: Register and setting values for common code
+ * @regmap: Devices register map
+ * @dev: Pointer to the devices device struct
+ * @led_sources - The LED strings supported in this array
+ * @num_leds - Number of LED strings are supported in this array
+ */
+struct lm36274 {
+ struct platform_device *pdev;
+ struct led_classdev led_dev;
+ struct ti_lmu_bank lmu_data;
+ struct regmap *regmap;
+ struct device *dev;
+
+ u32 led_sources[LM36274_MAX_STRINGS];
+ int num_leds;
+};
+
+static int lm36274_brightness_set(struct led_classdev *led_cdev,
+ enum led_brightness brt_val)
+{
+ struct lm36274 *led = container_of(led_cdev, struct lm36274, led_dev);
+
+ return ti_lmu_common_set_brightness(&led->lmu_data, brt_val);
+}
+
+static int lm36274_init(struct lm36274 *lm36274_data)
+{
+ int enable_val = 0;
+ int i;
+
+ for (i = 0; i < lm36274_data->num_leds; i++)
+ enable_val |= (1 << lm36274_data->led_sources[i]);
+
+ if (!enable_val) {
+ dev_err(lm36274_data->dev, "No LEDs were enabled\n");
+ return -EINVAL;
+ }
+
+ enable_val |= LM36274_BL_EN;
+
+ return regmap_write(lm36274_data->regmap, LM36274_REG_BL_EN,
+ enable_val);
+}
+
+static int lm36274_parse_dt(struct lm36274 *lm36274_data)
+{
+ struct fwnode_handle *child = NULL;
+ char label[LED_MAX_NAME_SIZE];
+ struct device *dev = &lm36274_data->pdev->dev;
+ const char *name;
+ int child_cnt;
+ int ret = -EINVAL;
+
+ /* There should only be 1 node */
+ child_cnt = device_get_child_node_count(dev);
+ if (child_cnt != 1)
+ return -EINVAL;
+
+ device_for_each_child_node(dev, child) {
+ ret = fwnode_property_read_string(child, "label", &name);
+ if (ret)
+ snprintf(label, sizeof(label),
+ "%s::", lm36274_data->pdev->name);
+ else
+ snprintf(label, sizeof(label),
+ "%s:%s", lm36274_data->pdev->name, name);
+
+ lm36274_data->num_leds = fwnode_property_read_u32_array(child,
+ "led-sources",
+ NULL, 0);
+ if (lm36274_data->num_leds <= 0)
+ return -ENODEV;
+
+ ret = fwnode_property_read_u32_array(child, "led-sources",
+ lm36274_data->led_sources,
+ lm36274_data->num_leds);
+ if (ret) {
+ dev_err(dev, "led-sources property missing\n");
+ return ret;
+ }
+
+ fwnode_property_read_string(child, "linux,default-trigger",
+ &lm36274_data->led_dev.default_trigger);
+
+ }
+
+ lm36274_data->lmu_data.regmap = lm36274_data->regmap;
+ lm36274_data->lmu_data.max_brightness = MAX_BRIGHTNESS_11BIT;
+ lm36274_data->lmu_data.msb_brightness_reg = LM36274_REG_BRT_MSB;
+ lm36274_data->lmu_data.lsb_brightness_reg = LM36274_REG_BRT_LSB;
+
+ lm36274_data->led_dev.name = label;
+ lm36274_data->led_dev.max_brightness = MAX_BRIGHTNESS_11BIT;
+ lm36274_data->led_dev.brightness_set_blocking = lm36274_brightness_set;
+
+ return 0;
+}
+
+static int lm36274_probe(struct platform_device *pdev)
+{
+ struct ti_lmu *lmu = dev_get_drvdata(pdev->dev.parent);
+ struct lm36274 *lm36274_data;
+ int ret;
+
+ lm36274_data = devm_kzalloc(&pdev->dev, sizeof(*lm36274_data),
+ GFP_KERNEL);
+ if (!lm36274_data)
+ return -ENOMEM;
+
+ lm36274_data->pdev = pdev;
+ lm36274_data->dev = lmu->dev;
+ lm36274_data->regmap = lmu->regmap;
+ dev_set_drvdata(&pdev->dev, lm36274_data);
+
+ ret = lm36274_parse_dt(lm36274_data);
+ if (ret) {
+ dev_err(lm36274_data->dev, "Failed to parse DT node\n");
+ return ret;
+ }
+
+ ret = lm36274_init(lm36274_data);
+ if (ret) {
+ dev_err(lm36274_data->dev, "Failed to init the device\n");
+ return ret;
+ }
+
+ return devm_led_classdev_register(lm36274_data->dev,
+ &lm36274_data->led_dev);
+}
+
+static const struct of_device_id of_lm36274_leds_match[] = {
+ { .compatible = "ti,lm36274-backlight", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_lm36274_leds_match);
+
+static struct platform_driver lm36274_driver = {
+ .probe = lm36274_probe,
+ .driver = {
+ .name = "lm36274-leds",
+ },
+};
+module_platform_driver(lm36274_driver)
+
+MODULE_DESCRIPTION("Texas Instruments LM36274 LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/leds/leds-lm3697.c b/drivers/leds/leds-lm3697.c
new file mode 100644
index 000000000000..54e0e35df824
--- /dev/null
+++ b/drivers/leds/leds-lm3697.c
@@ -0,0 +1,395 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LM3697 LED chip family driver
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/leds-ti-lmu-common.h>
+
+#define LM3697_REV 0x0
+#define LM3697_RESET 0x1
+#define LM3697_OUTPUT_CONFIG 0x10
+#define LM3697_CTRL_A_RAMP 0x11
+#define LM3697_CTRL_B_RAMP 0x12
+#define LM3697_CTRL_A_B_RT_RAMP 0x13
+#define LM3697_CTRL_A_B_RAMP_CFG 0x14
+#define LM3697_CTRL_A_B_BRT_CFG 0x16
+#define LM3697_CTRL_A_FS_CURR_CFG 0x17
+#define LM3697_CTRL_B_FS_CURR_CFG 0x18
+#define LM3697_PWM_CFG 0x1c
+#define LM3697_CTRL_A_BRT_LSB 0x20
+#define LM3697_CTRL_A_BRT_MSB 0x21
+#define LM3697_CTRL_B_BRT_LSB 0x22
+#define LM3697_CTRL_B_BRT_MSB 0x23
+#define LM3697_CTRL_ENABLE 0x24
+
+#define LM3697_SW_RESET BIT(0)
+
+#define LM3697_CTRL_A_EN BIT(0)
+#define LM3697_CTRL_B_EN BIT(1)
+#define LM3697_CTRL_A_B_EN (LM3697_CTRL_A_EN | LM3697_CTRL_B_EN)
+
+#define LM3697_MAX_LED_STRINGS 3
+
+#define LM3697_CONTROL_A 0
+#define LM3697_CONTROL_B 1
+#define LM3697_MAX_CONTROL_BANKS 2
+
+/**
+ * struct lm3697_led -
+ * @hvled_strings: Array of LED strings associated with a control bank
+ * @label: LED label
+ * @led_dev: LED class device
+ * @priv: Pointer to the device struct
+ * @lmu_data: Register and setting values for common code
+ * @control_bank: Control bank the LED is associated to. 0 is control bank A
+ * 1 is control bank B
+ */
+struct lm3697_led {
+ u32 hvled_strings[LM3697_MAX_LED_STRINGS];
+ char label[LED_MAX_NAME_SIZE];
+ struct led_classdev led_dev;
+ struct lm3697 *priv;
+ struct ti_lmu_bank lmu_data;
+ int control_bank;
+ int enabled;
+ int num_leds;
+};
+
+/**
+ * struct lm3697 -
+ * @enable_gpio: Hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: Pointer to the I2C client
+ * @regmap: Devices register map
+ * @dev: Pointer to the devices device struct
+ * @lock: Lock for reading/writing the device
+ * @leds: Array of LED strings
+ */
+struct lm3697 {
+ struct gpio_desc *enable_gpio;
+ struct regulator *regulator;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct device *dev;
+ struct mutex lock;
+
+ int bank_cfg;
+
+ struct lm3697_led leds[];
+};
+
+static const struct reg_default lm3697_reg_defs[] = {
+ {LM3697_OUTPUT_CONFIG, 0x6},
+ {LM3697_CTRL_A_RAMP, 0x0},
+ {LM3697_CTRL_B_RAMP, 0x0},
+ {LM3697_CTRL_A_B_RT_RAMP, 0x0},
+ {LM3697_CTRL_A_B_RAMP_CFG, 0x0},
+ {LM3697_CTRL_A_B_BRT_CFG, 0x0},
+ {LM3697_CTRL_A_FS_CURR_CFG, 0x13},
+ {LM3697_CTRL_B_FS_CURR_CFG, 0x13},
+ {LM3697_PWM_CFG, 0xc},
+ {LM3697_CTRL_A_BRT_LSB, 0x0},
+ {LM3697_CTRL_A_BRT_MSB, 0x0},
+ {LM3697_CTRL_B_BRT_LSB, 0x0},
+ {LM3697_CTRL_B_BRT_MSB, 0x0},
+ {LM3697_CTRL_ENABLE, 0x0},
+};
+
+static const struct regmap_config lm3697_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = LM3697_CTRL_ENABLE,
+ .reg_defaults = lm3697_reg_defs,
+ .num_reg_defaults = ARRAY_SIZE(lm3697_reg_defs),
+ .cache_type = REGCACHE_FLAT,
+};
+
+static int lm3697_brightness_set(struct led_classdev *led_cdev,
+ enum led_brightness brt_val)
+{
+ struct lm3697_led *led = container_of(led_cdev, struct lm3697_led,
+ led_dev);
+ int ctrl_en_val = (1 << led->control_bank);
+ int ret;
+
+ mutex_lock(&led->priv->lock);
+
+ if (brt_val == LED_OFF) {
+ ret = regmap_update_bits(led->priv->regmap, LM3697_CTRL_ENABLE,
+ ctrl_en_val, ~ctrl_en_val);
+ if (ret) {
+ dev_err(&led->priv->client->dev, "Cannot write ctrl register\n");
+ goto brightness_out;
+ }
+
+ led->enabled = LED_OFF;
+ } else {
+ ret = ti_lmu_common_set_brightness(&led->lmu_data, brt_val);
+ if (ret) {
+ dev_err(&led->priv->client->dev,
+ "Cannot write brightness\n");
+ goto brightness_out;
+ }
+
+ if (!led->enabled) {
+ ret = regmap_update_bits(led->priv->regmap,
+ LM3697_CTRL_ENABLE,
+ ctrl_en_val, ctrl_en_val);
+ if (ret) {
+ dev_err(&led->priv->client->dev,
+ "Cannot enable the device\n");
+ goto brightness_out;
+ }
+
+ led->enabled = brt_val;
+ }
+ }
+
+brightness_out:
+ mutex_unlock(&led->priv->lock);
+ return ret;
+}
+
+static int lm3697_init(struct lm3697 *priv)
+{
+ struct lm3697_led *led;
+ int i, ret;
+
+ if (priv->enable_gpio) {
+ gpiod_direction_output(priv->enable_gpio, 1);
+ } else {
+ ret = regmap_write(priv->regmap, LM3697_RESET, LM3697_SW_RESET);
+ if (ret) {
+ dev_err(&priv->client->dev, "Cannot reset the device\n");
+ goto out;
+ }
+ }
+
+ ret = regmap_write(priv->regmap, LM3697_CTRL_ENABLE, 0x0);
+ if (ret) {
+ dev_err(&priv->client->dev, "Cannot write ctrl enable\n");
+ goto out;
+ }
+
+ ret = regmap_write(priv->regmap, LM3697_OUTPUT_CONFIG, priv->bank_cfg);
+ if (ret)
+ dev_err(&priv->client->dev, "Cannot write OUTPUT config\n");
+
+ for (i = 0; i < LM3697_MAX_CONTROL_BANKS; i++) {
+ led = &priv->leds[i];
+ ret = ti_lmu_common_set_ramp(&led->lmu_data);
+ if (ret)
+ dev_err(&priv->client->dev, "Setting the ramp rate failed\n");
+ }
+out:
+ return ret;
+}
+
+static int lm3697_probe_dt(struct lm3697 *priv)
+{
+ struct fwnode_handle *child = NULL;
+ struct lm3697_led *led;
+ const char *name;
+ int control_bank;
+ size_t i = 0;
+ int ret = -EINVAL;
+ int j;
+
+ priv->enable_gpio = devm_gpiod_get_optional(&priv->client->dev,
+ "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(priv->enable_gpio)) {
+ ret = PTR_ERR(priv->enable_gpio);
+ dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+ ret);
+ return ret;
+ }
+
+ priv->regulator = devm_regulator_get(&priv->client->dev, "vled");
+ if (IS_ERR(priv->regulator))
+ priv->regulator = NULL;
+
+ device_for_each_child_node(priv->dev, child) {
+ ret = fwnode_property_read_u32(child, "reg", &control_bank);
+ if (ret) {
+ dev_err(&priv->client->dev, "reg property missing\n");
+ fwnode_handle_put(child);
+ goto child_out;
+ }
+
+ if (control_bank > LM3697_CONTROL_B) {
+ dev_err(&priv->client->dev, "reg property is invalid\n");
+ ret = -EINVAL;
+ fwnode_handle_put(child);
+ goto child_out;
+ }
+
+ led = &priv->leds[i];
+
+ ret = ti_lmu_common_get_brt_res(&priv->client->dev,
+ child, &led->lmu_data);
+ if (ret)
+ dev_warn(&priv->client->dev, "brightness resolution property missing\n");
+
+ led->control_bank = control_bank;
+ led->lmu_data.regmap = priv->regmap;
+ led->lmu_data.runtime_ramp_reg = LM3697_CTRL_A_RAMP +
+ control_bank;
+ led->lmu_data.msb_brightness_reg = LM3697_CTRL_A_BRT_MSB +
+ led->control_bank * 2;
+ led->lmu_data.lsb_brightness_reg = LM3697_CTRL_A_BRT_LSB +
+ led->control_bank * 2;
+
+ led->num_leds = fwnode_property_read_u32_array(child,
+ "led-sources",
+ NULL, 0);
+
+ if (led->num_leds > LM3697_MAX_LED_STRINGS) {
+ dev_err(&priv->client->dev, "To many LED strings defined\n");
+ continue;
+ }
+
+ ret = fwnode_property_read_u32_array(child, "led-sources",
+ led->hvled_strings,
+ led->num_leds);
+ if (ret) {
+ dev_err(&priv->client->dev, "led-sources property missing\n");
+ fwnode_handle_put(child);
+ goto child_out;
+ }
+
+ for (j = 0; j < led->num_leds; j++)
+ priv->bank_cfg |=
+ (led->control_bank << led->hvled_strings[j]);
+
+ ret = ti_lmu_common_get_ramp_params(&priv->client->dev,
+ child, &led->lmu_data);
+ if (ret)
+ dev_warn(&priv->client->dev, "runtime-ramp properties missing\n");
+
+ fwnode_property_read_string(child, "linux,default-trigger",
+ &led->led_dev.default_trigger);
+
+ ret = fwnode_property_read_string(child, "label", &name);
+ if (ret)
+ snprintf(led->label, sizeof(led->label),
+ "%s::", priv->client->name);
+ else
+ snprintf(led->label, sizeof(led->label),
+ "%s:%s", priv->client->name, name);
+
+ led->priv = priv;
+ led->led_dev.name = led->label;
+ led->led_dev.max_brightness = led->lmu_data.max_brightness;
+ led->led_dev.brightness_set_blocking = lm3697_brightness_set;
+
+ ret = devm_led_classdev_register(priv->dev, &led->led_dev);
+ if (ret) {
+ dev_err(&priv->client->dev, "led register err: %d\n",
+ ret);
+ fwnode_handle_put(child);
+ goto child_out;
+ }
+
+ i++;
+ }
+
+child_out:
+ return ret;
+}
+
+static int lm3697_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct lm3697 *led;
+ int count;
+ int ret;
+
+ count = device_get_child_node_count(&client->dev);
+ if (!count) {
+ dev_err(&client->dev, "LEDs are not defined in device tree!");
+ return -ENODEV;
+ }
+
+ led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+ GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ mutex_init(&led->lock);
+ i2c_set_clientdata(client, led);
+
+ led->client = client;
+ led->dev = &client->dev;
+ led->regmap = devm_regmap_init_i2c(client, &lm3697_regmap_config);
+ if (IS_ERR(led->regmap)) {
+ ret = PTR_ERR(led->regmap);
+ dev_err(&client->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = lm3697_probe_dt(led);
+ if (ret)
+ return ret;
+
+ return lm3697_init(led);
+}
+
+static int lm3697_remove(struct i2c_client *client)
+{
+ struct lm3697 *led = i2c_get_clientdata(client);
+ int ret;
+
+ ret = regmap_update_bits(led->regmap, LM3697_CTRL_ENABLE,
+ LM3697_CTRL_A_B_EN, 0);
+ if (ret) {
+ dev_err(&led->client->dev, "Failed to disable the device\n");
+ return ret;
+ }
+
+ if (led->enable_gpio)
+ gpiod_direction_output(led->enable_gpio, 0);
+
+ if (led->regulator) {
+ ret = regulator_disable(led->regulator);
+ if (ret)
+ dev_err(&led->client->dev,
+ "Failed to disable regulator\n");
+ }
+
+ mutex_destroy(&led->lock);
+
+ return 0;
+}
+
+static const struct i2c_device_id lm3697_id[] = {
+ { "lm3697", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lm3697_id);
+
+static const struct of_device_id of_lm3697_leds_match[] = {
+ { .compatible = "ti,lm3697", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_lm3697_leds_match);
+
+static struct i2c_driver lm3697_driver = {
+ .driver = {
+ .name = "lm3697",
+ .of_match_table = of_lm3697_leds_match,
+ },
+ .probe = lm3697_probe,
+ .remove = lm3697_remove,
+ .id_table = lm3697_id,
+};
+module_i2c_driver(lm3697_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LM3697 LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/leds/leds-max77650.c b/drivers/leds/leds-max77650.c
index 6b74ce9cac12..8a8e5c65b157 100644
--- a/drivers/leds/leds-max77650.c
+++ b/drivers/leds/leds-max77650.c
@@ -64,7 +64,6 @@ static int max77650_led_probe(struct platform_device *pdev)
{
struct device_node *of_node, *child;
struct max77650_led *leds, *led;
- struct device *parent;
struct device *dev;
struct regmap *map;
const char *label;
@@ -72,7 +71,6 @@ static int max77650_led_probe(struct platform_device *pdev)
u32 reg;
dev = &pdev->dev;
- parent = dev->parent;
of_node = dev->of_node;
if (!of_node)
diff --git a/drivers/leds/leds-pca955x.c b/drivers/leds/leds-pca955x.c
index c2bc8f569760..4037c504589c 100644
--- a/drivers/leds/leds-pca955x.c
+++ b/drivers/leds/leds-pca955x.c
@@ -429,7 +429,7 @@ static int pca955x_probe(struct i2c_client *client,
int ngpios = 0;
chip = &pca955x_chipdefs[id->driver_data];
- adapter = to_i2c_adapter(client->dev.parent);
+ adapter = client->adapter;
pdata = dev_get_platdata(&client->dev);
if (!pdata) {
pdata = pca955x_get_pdata(client, chip);
diff --git a/drivers/leds/leds-spi-byte.c b/drivers/leds/leds-spi-byte.c
new file mode 100644
index 000000000000..b231b563b7bb
--- /dev/null
+++ b/drivers/leds/leds-spi-byte.c
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Christian Mauderer <oss@c-mauderer.de>
+
+/*
+ * The driver supports controllers with a very simple SPI protocol:
+ * - one LED is controlled by a single byte on MOSI
+ * - the value of the byte gives the brightness between two values (lowest to
+ * highest)
+ * - no return value is necessary (no MISO signal)
+ *
+ * The value for minimum and maximum brightness depends on the device
+ * (compatible string).
+ *
+ * Supported devices:
+ * - "ubnt,acb-spi-led": Microcontroller (SONiX 8F26E611LA) based device used
+ * for example in Ubiquiti airCube ISP. Reverse engineered protocol for this
+ * controller:
+ * * Higher two bits set a mode. Lower six bits are a parameter.
+ * * Mode: 00 -> set brightness between 0x00 (min) and 0x3F (max)
+ * * Mode: 01 -> pulsing pattern (min -> max -> min) with an interval. From
+ * some tests, the period is about (50ms + 102ms * parameter). There is a
+ * slightly different pattern starting from 0x10 (longer gap between the
+ * pulses) but the time still follows that calculation.
+ * * Mode: 10 -> same as 01 but with only a ramp from min to max. Again a
+ * slight jump in the pattern at 0x10.
+ * * Mode: 11 -> blinking (off -> 25% -> off -> 25% -> ...) with a period of
+ * (105ms * parameter)
+ * NOTE: This driver currently only supports mode 00.
+ */
+
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mutex.h>
+#include <uapi/linux/uleds.h>
+
+struct spi_byte_chipdef {
+ /* SPI byte that will be send to switch the LED off */
+ u8 off_value;
+ /* SPI byte that will be send to switch the LED to maximum brightness */
+ u8 max_value;
+};
+
+struct spi_byte_led {
+ struct led_classdev ldev;
+ struct spi_device *spi;
+ char name[LED_MAX_NAME_SIZE];
+ struct mutex mutex;
+ const struct spi_byte_chipdef *cdef;
+};
+
+static const struct spi_byte_chipdef ubnt_acb_spi_led_cdef = {
+ .off_value = 0x0,
+ .max_value = 0x3F,
+};
+
+static const struct of_device_id spi_byte_dt_ids[] = {
+ { .compatible = "ubnt,acb-spi-led", .data = &ubnt_acb_spi_led_cdef },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, spi_byte_dt_ids);
+
+static int spi_byte_brightness_set_blocking(struct led_classdev *dev,
+ enum led_brightness brightness)
+{
+ struct spi_byte_led *led = container_of(dev, struct spi_byte_led, ldev);
+ u8 value;
+ int ret;
+
+ value = (u8) brightness + led->cdef->off_value;
+
+ mutex_lock(&led->mutex);
+ ret = spi_write(led->spi, &value, sizeof(value));
+ mutex_unlock(&led->mutex);
+
+ return ret;
+}
+
+static int spi_byte_probe(struct spi_device *spi)
+{
+ const struct of_device_id *of_dev_id;
+ struct device_node *child;
+ struct device *dev = &spi->dev;
+ struct spi_byte_led *led;
+ const char *name = "leds-spi-byte::";
+ const char *state;
+ int ret;
+
+ of_dev_id = of_match_device(spi_byte_dt_ids, dev);
+ if (!of_dev_id)
+ return -EINVAL;
+
+ if (of_get_child_count(dev->of_node) != 1) {
+ dev_err(dev, "Device must have exactly one LED sub-node.");
+ return -EINVAL;
+ }
+ child = of_get_next_child(dev->of_node, NULL);
+
+ led = devm_kzalloc(dev, sizeof(*led), GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ of_property_read_string(child, "label", &name);
+ strlcpy(led->name, name, sizeof(led->name));
+ led->spi = spi;
+ mutex_init(&led->mutex);
+ led->cdef = of_dev_id->data;
+ led->ldev.name = led->name;
+ led->ldev.brightness = LED_OFF;
+ led->ldev.max_brightness = led->cdef->max_value - led->cdef->off_value;
+ led->ldev.brightness_set_blocking = spi_byte_brightness_set_blocking;
+
+ state = of_get_property(child, "default-state", NULL);
+ if (state) {
+ if (!strcmp(state, "on")) {
+ led->ldev.brightness = led->ldev.max_brightness;
+ } else if (strcmp(state, "off")) {
+ /* all other cases except "off" */
+ dev_err(dev, "default-state can only be 'on' or 'off'");
+ return -EINVAL;
+ }
+ }
+ spi_byte_brightness_set_blocking(&led->ldev,
+ led->ldev.brightness);
+
+ ret = devm_led_classdev_register(&spi->dev, &led->ldev);
+ if (ret) {
+ mutex_destroy(&led->mutex);
+ return ret;
+ }
+ spi_set_drvdata(spi, led);
+
+ return 0;
+}
+
+static int spi_byte_remove(struct spi_device *spi)
+{
+ struct spi_byte_led *led = spi_get_drvdata(spi);
+
+ mutex_destroy(&led->mutex);
+
+ return 0;
+}
+
+static struct spi_driver spi_byte_driver = {
+ .probe = spi_byte_probe,
+ .remove = spi_byte_remove,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = spi_byte_dt_ids,
+ },
+};
+
+module_spi_driver(spi_byte_driver);
+
+MODULE_AUTHOR("Christian Mauderer <oss@c-mauderer.de>");
+MODULE_DESCRIPTION("single byte SPI LED driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("spi:leds-spi-byte");
diff --git a/drivers/leds/leds-tca6507.c b/drivers/leds/leds-tca6507.c
index c59035e157d1..58be20cae183 100644
--- a/drivers/leds/leds-tca6507.c
+++ b/drivers/leds/leds-tca6507.c
@@ -758,7 +758,7 @@ static int tca6507_probe(struct i2c_client *client,
int err;
int i = 0;
- adapter = to_i2c_adapter(client->dev.parent);
+ adapter = client->adapter;
pdata = dev_get_platdata(&client->dev);
if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))
diff --git a/drivers/leds/leds-ti-lmu-common.c b/drivers/leds/leds-ti-lmu-common.c
new file mode 100644
index 000000000000..adc7293004f1
--- /dev/null
+++ b/drivers/leds/leds-ti-lmu-common.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright 2015 Texas Instruments
+// Copyright 2018 Sebastian Reichel
+// Copyright 2018 Pavel Machek <pavel@ucw.cz>
+// TI LMU LED common framework, based on previous work from
+// Milo Kim <milo.kim@ti.com>
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/of_device.h>
+
+#include <linux/leds-ti-lmu-common.h>
+
+const static int ramp_table[16] = {2048, 262000, 524000, 1049000, 2090000,
+ 4194000, 8389000, 16780000, 33550000, 41940000,
+ 50330000, 58720000, 67110000, 83880000,
+ 100660000, 117440000};
+
+static int ti_lmu_common_update_brightness(struct ti_lmu_bank *lmu_bank,
+ int brightness)
+{
+ struct regmap *regmap = lmu_bank->regmap;
+ u8 reg, val;
+ int ret;
+
+ /*
+ * Brightness register update
+ *
+ * 11 bit dimming: update LSB bits and write MSB byte.
+ * MSB brightness should be shifted.
+ * 8 bit dimming: write MSB byte.
+ */
+ if (lmu_bank->max_brightness == MAX_BRIGHTNESS_11BIT) {
+ reg = lmu_bank->lsb_brightness_reg;
+ ret = regmap_update_bits(regmap, reg,
+ LMU_11BIT_LSB_MASK,
+ brightness);
+ if (ret)
+ return ret;
+
+ val = brightness >> LMU_11BIT_MSB_SHIFT;
+ } else {
+ val = brightness;
+ }
+
+ reg = lmu_bank->msb_brightness_reg;
+
+ return regmap_write(regmap, reg, val);
+}
+
+int ti_lmu_common_set_brightness(struct ti_lmu_bank *lmu_bank, int brightness)
+{
+ return ti_lmu_common_update_brightness(lmu_bank, brightness);
+}
+EXPORT_SYMBOL(ti_lmu_common_set_brightness);
+
+static int ti_lmu_common_convert_ramp_to_index(unsigned int usec)
+{
+ int size = ARRAY_SIZE(ramp_table);
+ int i;
+
+ if (usec <= ramp_table[0])
+ return 0;
+
+ if (usec > ramp_table[size - 1])
+ return size - 1;
+
+ for (i = 1; i < size; i++) {
+ if (usec == ramp_table[i])
+ return i;
+
+ /* Find an approximate index by looking up the table */
+ if (usec > ramp_table[i - 1] && usec < ramp_table[i]) {
+ if (usec - ramp_table[i - 1] < ramp_table[i] - usec)
+ return i - 1;
+ else
+ return i;
+ }
+ }
+
+ return -EINVAL;
+}
+
+int ti_lmu_common_set_ramp(struct ti_lmu_bank *lmu_bank)
+{
+ struct regmap *regmap = lmu_bank->regmap;
+ u8 ramp, ramp_up, ramp_down;
+
+ if (lmu_bank->ramp_up_usec == 0 && lmu_bank->ramp_down_usec == 0) {
+ ramp_up = 0;
+ ramp_down = 0;
+ } else {
+ ramp_up = ti_lmu_common_convert_ramp_to_index(lmu_bank->ramp_up_usec);
+ ramp_down = ti_lmu_common_convert_ramp_to_index(lmu_bank->ramp_down_usec);
+ }
+
+ if (ramp_up < 0 || ramp_down < 0)
+ return -EINVAL;
+
+ ramp = (ramp_up << 4) | ramp_down;
+
+ return regmap_write(regmap, lmu_bank->runtime_ramp_reg, ramp);
+
+}
+EXPORT_SYMBOL(ti_lmu_common_set_ramp);
+
+int ti_lmu_common_get_ramp_params(struct device *dev,
+ struct fwnode_handle *child,
+ struct ti_lmu_bank *lmu_data)
+{
+ int ret;
+
+ ret = fwnode_property_read_u32(child, "ramp-up-us",
+ &lmu_data->ramp_up_usec);
+ if (ret)
+ dev_warn(dev, "ramp-up-us property missing\n");
+
+
+ ret = fwnode_property_read_u32(child, "ramp-down-us",
+ &lmu_data->ramp_down_usec);
+ if (ret)
+ dev_warn(dev, "ramp-down-us property missing\n");
+
+ return 0;
+}
+EXPORT_SYMBOL(ti_lmu_common_get_ramp_params);
+
+int ti_lmu_common_get_brt_res(struct device *dev, struct fwnode_handle *child,
+ struct ti_lmu_bank *lmu_data)
+{
+ int ret;
+
+ ret = device_property_read_u32(dev, "ti,brightness-resolution",
+ &lmu_data->max_brightness);
+ if (ret)
+ ret = fwnode_property_read_u32(child,
+ "ti,brightness-resolution",
+ &lmu_data->max_brightness);
+ if (lmu_data->max_brightness <= 0) {
+ lmu_data->max_brightness = MAX_BRIGHTNESS_8BIT;
+ return ret;
+ }
+
+ if (lmu_data->max_brightness > MAX_BRIGHTNESS_11BIT)
+ lmu_data->max_brightness = MAX_BRIGHTNESS_11BIT;
+
+
+ return 0;
+}
+EXPORT_SYMBOL(ti_lmu_common_get_brt_res);
+
+MODULE_DESCRIPTION("TI LMU common LED framework");
+MODULE_AUTHOR("Sebastian Reichel");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("ti-lmu-led-common");
diff --git a/drivers/leds/trigger/Kconfig b/drivers/leds/trigger/Kconfig
index 7fa9d174a40c..ce9429ca6dde 100644
--- a/drivers/leds/trigger/Kconfig
+++ b/drivers/leds/trigger/Kconfig
@@ -15,7 +15,7 @@ config LEDS_TRIGGER_TIMER
This allows LEDs to be controlled by a programmable timer
via sysfs. Some LED hardware can be programmed to start
blinking the LED without any further software interaction.
- For more details read Documentation/leds/leds-class.txt.
+ For more details read Documentation/leds/leds-class.rst.
If unsure, say Y.
diff --git a/drivers/leds/trigger/ledtrig-transient.c b/drivers/leds/trigger/ledtrig-transient.c
index a80bb82aacc2..80635183fac8 100644
--- a/drivers/leds/trigger/ledtrig-transient.c
+++ b/drivers/leds/trigger/ledtrig-transient.c
@@ -3,7 +3,7 @@
// LED Kernel Transient Trigger
//
// Transient trigger allows one shot timer activation. Please refer to
-// Documentation/leds/ledtrig-transient.txt for details
+// Documentation/leds/ledtrig-transient.rst for details
// Copyright (C) 2012 Shuah Khan <shuahkhan@gmail.com>
//
// Based on Richard Purdie's ledtrig-timer.c and Atsushi Nemoto's
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index a17d275bf1d4..6855ff443e04 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1336,9 +1336,8 @@ config MFD_TI_LMU
select REGMAP_I2C
help
Say yes here to enable support for TI LMU chips.
-
- TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
- It consists of backlight, LED and regulator driver.
+ TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and
+ LM36274. It consists of backlight, LED and regulator driver.
It provides consistent device controls for lighting functions.
config MFD_OMAP_USB_HOST
diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c
index 96b21b5af570..fd6e8c417baa 100644
--- a/drivers/mfd/ti-lmu.c
+++ b/drivers/mfd/ti-lmu.c
@@ -108,17 +108,14 @@ static const struct mfd_cell lm3695_devices[] = {
},
};
-static const struct mfd_cell lm3697_devices[] = {
+static const struct mfd_cell lm36274_devices[] = {
+ LM363X_REGULATOR(LM36274_BOOST),
+ LM363X_REGULATOR(LM36274_LDO_POS),
+ LM363X_REGULATOR(LM36274_LDO_NEG),
{
- .name = "ti-lmu-backlight",
- .id = LM3697,
- .of_compatible = "ti,lm3697-backlight",
- },
- /* Monitoring driver for open/short circuit detection */
- {
- .name = "ti-lmu-fault-monitor",
- .id = LM3697,
- .of_compatible = "ti,lm3697-fault-monitor",
+ .name = "lm36274-leds",
+ .id = LM36274,
+ .of_compatible = "ti,lm36274-backlight",
},
};
@@ -134,7 +131,7 @@ TI_LMU_DATA(lm3631, LM3631_MAX_REG);
TI_LMU_DATA(lm3632, LM3632_MAX_REG);
TI_LMU_DATA(lm3633, LM3633_MAX_REG);
TI_LMU_DATA(lm3695, LM3695_MAX_REG);
-TI_LMU_DATA(lm3697, LM3697_MAX_REG);
+TI_LMU_DATA(lm36274, LM36274_MAX_REG);
static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id)
{
@@ -203,7 +200,7 @@ static const struct of_device_id ti_lmu_of_match[] = {
{ .compatible = "ti,lm3632", .data = &lm3632_data },
{ .compatible = "ti,lm3633", .data = &lm3633_data },
{ .compatible = "ti,lm3695", .data = &lm3695_data },
- { .compatible = "ti,lm3697", .data = &lm3697_data },
+ { .compatible = "ti,lm36274", .data = &lm36274_data },
{ }
};
MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
@@ -213,7 +210,7 @@ static const struct i2c_device_id ti_lmu_ids[] = {
{ "lm3632", LM3632 },
{ "lm3633", LM3633 },
{ "lm3695", LM3695 },
- { "lm3697", LM3697 },
+ { "lm36274", LM36274 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 8553bdf87c1d..b5d0e07a62d7 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -364,7 +364,7 @@ config REGULATOR_LM363X
tristate "TI LM363X voltage regulators"
depends on MFD_TI_LMU
help
- This driver supports LM3631 and LM3632 voltage regulators for
+ This driver supports LM3631, LM3632 and LM36274 voltage regulators for
the LCD bias.
One boost output voltage is configurable and always on.
Other LDOs are used for the display module.
diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
index 60f15a722760..5647e2f97ff8 100644
--- a/drivers/regulator/lm363x-regulator.c
+++ b/drivers/regulator/lm363x-regulator.c
@@ -34,6 +34,11 @@
#define LM3632_VBOOST_MIN 4500000
#define LM3632_VLDO_MIN 4000000
+/* LM36274 */
+#define LM36274_BOOST_VSEL_MAX 0x3f
+#define LM36274_LDO_VSEL_MAX 0x34
+#define LM36274_VOLTAGE_MIN 4000000
+
/* Common */
#define LM363X_STEP_50mV 50000
#define LM363X_STEP_500mV 500000
@@ -214,6 +219,51 @@ static const struct regulator_desc lm363x_regulator_desc[] = {
.enable_reg = LM3632_REG_BIAS_CONFIG,
.enable_mask = LM3632_EN_VNEG_MASK,
},
+
+ /* LM36274 */
+ {
+ .name = "vboost",
+ .of_match = "vboost",
+ .id = LM36274_BOOST,
+ .ops = &lm363x_boost_voltage_table_ops,
+ .n_voltages = LM36274_BOOST_VSEL_MAX,
+ .min_uV = LM36274_VOLTAGE_MIN,
+ .uV_step = LM363X_STEP_50mV,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .vsel_reg = LM36274_REG_VOUT_BOOST,
+ .vsel_mask = LM36274_VOUT_MASK,
+ },
+ {
+ .name = "ldo_vpos",
+ .of_match = "vpos",
+ .id = LM36274_LDO_POS,
+ .ops = &lm363x_regulator_voltage_table_ops,
+ .n_voltages = LM36274_LDO_VSEL_MAX,
+ .min_uV = LM36274_VOLTAGE_MIN,
+ .uV_step = LM363X_STEP_50mV,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .vsel_reg = LM36274_REG_VOUT_POS,
+ .vsel_mask = LM36274_VOUT_MASK,
+ .enable_reg = LM36274_REG_BIAS_CONFIG_1,
+ .enable_mask = LM36274_EN_VPOS_MASK,
+ },
+ {
+ .name = "ldo_vneg",
+ .of_match = "vneg",
+ .id = LM36274_LDO_NEG,
+ .ops = &lm363x_regulator_voltage_table_ops,
+ .n_voltages = LM36274_LDO_VSEL_MAX,
+ .min_uV = LM36274_VOLTAGE_MIN,
+ .uV_step = LM363X_STEP_50mV,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .vsel_reg = LM36274_REG_VOUT_NEG,
+ .vsel_mask = LM36274_VOUT_MASK,
+ .enable_reg = LM36274_REG_BIAS_CONFIG_1,
+ .enable_mask = LM36274_EN_VNEG_MASK,
+ },
};
static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev, int id)
@@ -226,9 +276,11 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
*/
switch (id) {
case LM3632_LDO_POS:
+ case LM36274_LDO_POS:
return gpiod_get_index_optional(dev, "enable", 0,
GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
case LM3632_LDO_NEG:
+ case LM36274_LDO_NEG:
return gpiod_get_index_optional(dev, "enable", 1,
GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
default:
@@ -236,6 +288,27 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
}
}
+static int lm363x_regulator_set_ext_en(struct regmap *regmap, int id)
+{
+ int ext_en_mask = 0;
+
+ switch (id) {
+ case LM3632_LDO_POS:
+ case LM3632_LDO_NEG:
+ ext_en_mask = LM3632_EXT_EN_MASK;
+ break;
+ case LM36274_LDO_POS:
+ case LM36274_LDO_NEG:
+ ext_en_mask = LM36274_EXT_EN_MASK;
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ return regmap_update_bits(regmap, lm363x_regulator_desc[id].enable_reg,
+ ext_en_mask, ext_en_mask);
+}
+
static int lm363x_regulator_probe(struct platform_device *pdev)
{
struct ti_lmu *lmu = dev_get_drvdata(pdev->dev.parent);
@@ -260,10 +333,7 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
if (gpiod) {
cfg.ena_gpiod = gpiod;
-
- ret = regmap_update_bits(regmap, LM3632_REG_BIAS_CONFIG,
- LM3632_EXT_EN_MASK,
- LM3632_EXT_EN_MASK);
+ ret = lm363x_regulator_set_ext_en(regmap, id);
if (ret) {
gpiod_put(gpiod);
dev_err(dev, "External pin err: %d\n", ret);
diff --git a/include/linux/leds-ti-lmu-common.h b/include/linux/leds-ti-lmu-common.h
new file mode 100644
index 000000000000..5eb111f38803
--- /dev/null
+++ b/include/linux/leds-ti-lmu-common.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+// TI LMU Common Core
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#ifndef _TI_LMU_COMMON_H_
+#define _TI_LMU_COMMON_H_
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#define LMU_11BIT_LSB_MASK (BIT(0) | BIT(1) | BIT(2))
+#define LMU_11BIT_MSB_SHIFT 3
+
+#define MAX_BRIGHTNESS_8BIT 255
+#define MAX_BRIGHTNESS_11BIT 2047
+
+struct ti_lmu_bank {
+ struct regmap *regmap;
+
+ int max_brightness;
+
+ u8 lsb_brightness_reg;
+ u8 msb_brightness_reg;
+
+ u8 runtime_ramp_reg;
+ u32 ramp_up_usec;
+ u32 ramp_down_usec;
+};
+
+int ti_lmu_common_set_brightness(struct ti_lmu_bank *lmu_bank, int brightness);
+
+int ti_lmu_common_set_ramp(struct ti_lmu_bank *lmu_bank);
+
+int ti_lmu_common_get_ramp_params(struct device *dev,
+ struct fwnode_handle *child,
+ struct ti_lmu_bank *lmu_data);
+
+int ti_lmu_common_get_brt_res(struct device *dev, struct fwnode_handle *child,
+ struct ti_lmu_bank *lmu_data);
+
+#endif /* _TI_LMU_COMMON_H_ */
diff --git a/include/linux/mfd/ti-lmu-register.h b/include/linux/mfd/ti-lmu-register.h
index 222cb14c5b0f..116a749e0302 100644
--- a/include/linux/mfd/ti-lmu-register.h
+++ b/include/linux/mfd/ti-lmu-register.h
@@ -187,47 +187,26 @@
#define LM3695_MAX_REG 0x14
-/* LM3697 */
-#define LM3697_REG_HVLED_OUTPUT_CFG 0x10
-#define LM3697_HVLED1_CFG_MASK BIT(0)
-#define LM3697_HVLED2_CFG_MASK BIT(1)
-#define LM3697_HVLED3_CFG_MASK BIT(2)
-#define LM3697_HVLED1_CFG_SHIFT 0
-#define LM3697_HVLED2_CFG_SHIFT 1
-#define LM3697_HVLED3_CFG_SHIFT 2
+/* LM36274 */
+#define LM36274_REG_REV 0x01
+#define LM36274_REG_BL_CFG_1 0x02
+#define LM36274_REG_BL_CFG_2 0x03
+#define LM36274_REG_BRT_LSB 0x04
+#define LM36274_REG_BRT_MSB 0x05
+#define LM36274_REG_BL_EN 0x08
+
+#define LM36274_REG_BIAS_CONFIG_1 0x09
+#define LM36274_EXT_EN_MASK BIT(0)
+#define LM36274_EN_VNEG_MASK BIT(1)
+#define LM36274_EN_VPOS_MASK BIT(2)
+
+#define LM36274_REG_BIAS_CONFIG_2 0x0a
+#define LM36274_REG_BIAS_CONFIG_3 0x0b
+#define LM36274_REG_VOUT_BOOST 0x0c
+#define LM36274_REG_VOUT_POS 0x0d
+#define LM36274_REG_VOUT_NEG 0x0e
+#define LM36274_VOUT_MASK 0x3F
+
+#define LM36274_MAX_REG 0x13
-#define LM3697_REG_BL0_RAMP 0x11
-#define LM3697_REG_BL1_RAMP 0x12
-#define LM3697_RAMPUP_MASK 0xF0
-#define LM3697_RAMPUP_SHIFT 4
-#define LM3697_RAMPDN_MASK 0x0F
-#define LM3697_RAMPDN_SHIFT 0
-
-#define LM3697_REG_RAMP_CONF 0x14
-#define LM3697_RAMP_MASK 0x0F
-#define LM3697_RAMP_EACH 0x05
-
-#define LM3697_REG_PWM_CFG 0x1C
-#define LM3697_PWM_A_MASK BIT(0)
-#define LM3697_PWM_B_MASK BIT(1)
-
-#define LM3697_REG_IMAX_A 0x17
-#define LM3697_REG_IMAX_B 0x18
-
-#define LM3697_REG_FEEDBACK_ENABLE 0x19
-
-#define LM3697_REG_BRT_A_LSB 0x20
-#define LM3697_REG_BRT_A_MSB 0x21
-#define LM3697_REG_BRT_B_LSB 0x22
-#define LM3697_REG_BRT_B_MSB 0x23
-
-#define LM3697_REG_ENABLE 0x24
-
-#define LM3697_REG_OPEN_FAULT_STATUS 0xB0
-
-#define LM3697_REG_SHORT_FAULT_STATUS 0xB2
-
-#define LM3697_REG_MONITOR_ENABLE 0xB4
-
-#define LM3697_MAX_REG 0xB4
#endif
diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h
index 7d1e9c24f818..0bc0e8199798 100644
--- a/include/linux/mfd/ti-lmu.h
+++ b/include/linux/mfd/ti-lmu.h
@@ -23,7 +23,7 @@ enum ti_lmu_id {
LM3632,
LM3633,
LM3695,
- LM3697,
+ LM36274,
LMU_MAX_ID,
};
@@ -65,6 +65,9 @@ enum lm363x_regulator_id {
LM3632_BOOST, /* Boost output */
LM3632_LDO_POS, /* Positive display bias output */
LM3632_LDO_NEG, /* Negative display bias output */
+ LM36274_BOOST, /* Boost output */
+ LM36274_LDO_POS, /* Positive display bias output */
+ LM36274_LDO_NEG, /* Negative display bias output */
};
/**
diff --git a/net/netfilter/Kconfig b/net/netfilter/Kconfig
index 21025c2c605b..66cc11742355 100644
--- a/net/netfilter/Kconfig
+++ b/net/netfilter/Kconfig
@@ -906,7 +906,7 @@ config NETFILTER_XT_TARGET_LED
echo netfilter-ssh > /sys/class/leds/<ledname>/trigger
For more information on the LEDs available on your system, see
- Documentation/leds/leds-class.txt
+ Documentation/leds/leds-class.rst
config NETFILTER_XT_TARGET_LOG
tristate "LOG target support"