diff options
Diffstat (limited to 'Documentation/block')
| -rw-r--r-- | Documentation/block/biodoc.txt | 11 | ||||
| -rw-r--r-- | Documentation/block/queue-sysfs.txt | 63 |
2 files changed, 69 insertions, 5 deletions
diff --git a/Documentation/block/biodoc.txt b/Documentation/block/biodoc.txt index 3c5434c83daf..ecad6ee75705 100644 --- a/Documentation/block/biodoc.txt +++ b/Documentation/block/biodoc.txt @@ -186,8 +186,9 @@ a virtual address mapping (unlike the earlier scheme of virtual address do not have a corresponding kernel virtual address space mapping) and low-memory pages. -Note: Please refer to DMA-mapping.txt for a discussion on PCI high mem DMA -aspects and mapping of scatter gather lists, and support for 64 bit PCI. +Note: Please refer to Documentation/PCI/PCI-DMA-mapping.txt for a discussion +on PCI high mem DMA aspects and mapping of scatter gather lists, and support +for 64 bit PCI. Special handling is required only for cases where i/o needs to happen on pages at physical memory addresses beyond what the device can support. In these @@ -953,14 +954,14 @@ elevator_allow_merge_fn called whenever the block layer determines results in some sort of conflict internally, this hook allows it to do that. -elevator_dispatch_fn fills the dispatch queue with ready requests. +elevator_dispatch_fn* fills the dispatch queue with ready requests. I/O schedulers are free to postpone requests by not filling the dispatch queue unless @force is non-zero. Once dispatched, I/O schedulers are not allowed to manipulate the requests - they belong to generic dispatch queue. -elevator_add_req_fn called to add a new request into the scheduler +elevator_add_req_fn* called to add a new request into the scheduler elevator_queue_empty_fn returns true if the merge queue is empty. Drivers shouldn't use this, but rather check @@ -990,7 +991,7 @@ elevator_activate_req_fn Called when device driver first sees a request. elevator_deactivate_req_fn Called when device driver decides to delay a request by requeueing it. -elevator_init_fn +elevator_init_fn* elevator_exit_fn Allocate and free any elevator specific storage for a queue. diff --git a/Documentation/block/queue-sysfs.txt b/Documentation/block/queue-sysfs.txt new file mode 100644 index 000000000000..e164403f60e1 --- /dev/null +++ b/Documentation/block/queue-sysfs.txt @@ -0,0 +1,63 @@ +Queue sysfs files +================= + +This text file will detail the queue files that are located in the sysfs tree +for each block device. Note that stacked devices typically do not export +any settings, since their queue merely functions are a remapping target. +These files are the ones found in the /sys/block/xxx/queue/ directory. + +Files denoted with a RO postfix are readonly and the RW postfix means +read-write. + +hw_sector_size (RO) +------------------- +This is the hardware sector size of the device, in bytes. + +max_hw_sectors_kb (RO) +---------------------- +This is the maximum number of kilobytes supported in a single data transfer. + +max_sectors_kb (RW) +------------------- +This is the maximum number of kilobytes that the block layer will allow +for a filesystem request. Must be smaller than or equal to the maximum +size allowed by the hardware. + +nomerges (RW) +------------- +This enables the user to disable the lookup logic involved with IO merging +requests in the block layer. Merging may still occur through a direct +1-hit cache, since that comes for (almost) free. The IO scheduler will not +waste cycles doing tree/hash lookups for merges if nomerges is 1. Defaults +to 0, enabling all merges. + +nr_requests (RW) +---------------- +This controls how many requests may be allocated in the block layer for +read or write requests. Note that the total allocated number may be twice +this amount, since it applies only to reads or writes (not the accumulated +sum). + +read_ahead_kb (RW) +------------------ +Maximum number of kilobytes to read-ahead for filesystems on this block +device. + +rq_affinity (RW) +---------------- +If this option is enabled, the block layer will migrate request completions +to the CPU that originally submitted the request. For some workloads +this provides a significant reduction in CPU cycles due to caching effects. + +scheduler (RW) +-------------- +When read, this file will display the current and available IO schedulers +for this block device. The currently active IO scheduler will be enclosed +in [] brackets. Writing an IO scheduler name to this file will switch +control of this block device to that new IO scheduler. Note that writing +an IO scheduler name to this file will attempt to load that IO scheduler +module, if it isn't already present in the system. + + + +Jens Axboe <jens.axboe@oracle.com>, February 2009 |