diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
36 files changed, 1463 insertions, 494 deletions
diff --git a/Documentation/devicetree/bindings/net/adi,adin1110.yaml b/Documentation/devicetree/bindings/net/adi,adin1110.yaml index b6bd8ee38a18..9de865295d7a 100644 --- a/Documentation/devicetree/bindings/net/adi,adin1110.yaml +++ b/Documentation/devicetree/bindings/net/adi,adin1110.yaml @@ -46,6 +46,10 @@ properties: interrupts: maxItems: 1 + reset-gpios: + maxItems: 1 + description: GPIO connected to active low reset + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/asix,ax88178.yaml b/Documentation/devicetree/bindings/net/asix,ax88178.yaml index 1af52358de4c..a81dbc4792f6 100644 --- a/Documentation/devicetree/bindings/net/asix,ax88178.yaml +++ b/Documentation/devicetree/bindings/net/asix,ax88178.yaml @@ -27,7 +27,9 @@ properties: - usbb95,772b # ASIX AX88772B - usbb95,7e2b # ASIX AX88772B - reg: true + reg: + maxItems: 1 + local-mac-address: true mac-address: true diff --git a/Documentation/devicetree/bindings/net/bluetooth.txt b/Documentation/devicetree/bindings/net/bluetooth.txt deleted file mode 100644 index 94797df751b8..000000000000 --- a/Documentation/devicetree/bindings/net/bluetooth.txt +++ /dev/null @@ -1,5 +0,0 @@ -The following properties are common to the Bluetooth controllers: - -- local-bd-address: array of 6 bytes, specifies the BD address that was - uniquely assigned to the Bluetooth device, formatted with least significant - byte first (little-endian). diff --git a/Documentation/devicetree/bindings/net/bluetooth/bluetooth-controller.yaml b/Documentation/devicetree/bindings/net/bluetooth/bluetooth-controller.yaml new file mode 100644 index 000000000000..9309dc40f54f --- /dev/null +++ b/Documentation/devicetree/bindings/net/bluetooth/bluetooth-controller.yaml @@ -0,0 +1,29 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/bluetooth-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bluetooth Controller Generic Binding + +maintainers: + - Marcel Holtmann <marcel@holtmann.org> + - Johan Hedberg <johan.hedberg@gmail.com> + - Luiz Augusto von Dentz <luiz.dentz@gmail.com> + +properties: + $nodename: + pattern: "^bluetooth(@.*)?$" + + local-bd-address: + $ref: /schemas/types.yaml#/definitions/uint8-array + maxItems: 6 + description: + Specifies the BD address that was uniquely assigned to the Bluetooth + device. Formatted with least significant byte first (little-endian), e.g. + in order to assign the address 00:11:22:33:44:55 this property must have + the value [55 44 33 22 11 00]. + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/net/bluetooth/brcm,bcm4377-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/brcm,bcm4377-bluetooth.yaml new file mode 100644 index 000000000000..37cb39a3a62e --- /dev/null +++ b/Documentation/devicetree/bindings/net/bluetooth/brcm,bcm4377-bluetooth.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/brcm,bcm4377-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4377 family PCIe Bluetooth Chips + +maintainers: + - Sven Peter <sven@svenpeter.dev> + +description: + This binding describes Broadcom BCM4377 family PCIe-attached bluetooth chips + usually found in Apple machines. The Wi-Fi part of the chip is described in + bindings/net/wireless/brcm,bcm4329-fmac.yaml. + +allOf: + - $ref: bluetooth-controller.yaml# + +properties: + compatible: + enum: + - pci14e4,5fa0 # BCM4377 + - pci14e4,5f69 # BCM4378 + - pci14e4,5f71 # BCM4387 + + reg: + maxItems: 1 + + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Board type of the Bluetooth chip. This is used to decouple + the overall system board from the Bluetooth module and used to construct + firmware and calibration data filenames. + On Apple platforms, this should be the Apple module-instance codename + prefixed by "apple,", e.g. "apple,atlantisb". + pattern: '^apple,.*' + + brcm,taurus-cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Bluetooth radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device. + This blob is used if the chip stepping of the Bluetooth module does not + support beamforming. + + brcm,taurus-bf-cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Bluetooth radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device. + This blob is used if the chip stepping of the Bluetooth module supports + beamforming. + + local-bd-address: true + +required: + - compatible + - reg + - local-bd-address + - brcm,board-type + +additionalProperties: false + +examples: + - | + pcie@a0000000 { + #address-cells = <3>; + #size-cells = <2>; + reg = <0xa0000000 0x1000000>; + device_type = "pci"; + ranges = <0x43000000 0x6 0xa0000000 0xa0000000 0x0 0x20000000>; + + bluetooth@0,1 { + compatible = "pci14e4,5f69"; + reg = <0x100 0x0 0x0 0x0 0x0>; + brcm,board-type = "apple,honshu"; + /* To be filled by the bootloader */ + local-bd-address = [00 00 00 00 00 00]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml index f93c6e7a1b59..a6a6b0e4df7a 100644 --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +++ b/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Bluetooth Chips @@ -79,8 +79,7 @@ properties: firmware-name: description: specify the name of nvm firmware to load - local-bd-address: - description: see Documentation/devicetree/bindings/net/bluetooth.txt + local-bd-address: true required: @@ -89,6 +88,7 @@ required: additionalProperties: false allOf: + - $ref: bluetooth-controller.yaml# - if: properties: compatible: diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml index 445b2a553625..b964c7dcec15 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml @@ -19,11 +19,14 @@ properties: - brcm,bcm4329-bt - brcm,bcm4330-bt - brcm,bcm4334-bt + - brcm,bcm43430a0-bt + - brcm,bcm43430a1-bt - brcm,bcm43438-bt - brcm,bcm4345c5 - brcm,bcm43540-bt - brcm,bcm4335a0 - brcm,bcm4349-bt + - cypress,cyw4373a0-bt - infineon,cyw55572-bt shutdown-gpios: diff --git a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml index e52db841bb8c..6e59bd2a6094 100644 --- a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml +++ b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml @@ -17,6 +17,7 @@ properties: compatible: oneOf: - enum: + - fsl,imx93-flexcan - fsl,imx8qm-flexcan - fsl,imx8mp-flexcan - fsl,imx6q-flexcan diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml index 6f71fc96bc4e..1eb98c9a1a26 100644 --- a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml @@ -9,9 +9,6 @@ title: Renesas R-Car CAN FD Controller maintainers: - Fabrizio Castro <fabrizio.castro.jz@renesas.com> -allOf: - - $ref: can-controller.yaml# - properties: compatible: oneOf: @@ -33,7 +30,7 @@ properties: - items: - enum: - - renesas,r9a07g043-canfd # RZ/G2UL + - renesas,r9a07g043-canfd # RZ/G2UL and RZ/Five - renesas,r9a07g044-canfd # RZ/G2{L,LC} - renesas,r9a07g054-canfd # RZ/V2L - const: renesas,rzg2l-canfd # RZ/G2L family @@ -77,12 +74,13 @@ properties: description: Maximum frequency of the CANFD clock. patternProperties: - "^channel[01]$": + "^channel[0-7]$": type: object description: - The controller supports two channels and each is represented as a child - node. Each child node supports the "status" property only, which - is used to enable/disable the respective channel. + The controller supports multiple channels and each is represented as a + child node. Each channel can be enabled/disabled individually. + + additionalProperties: false required: - compatible @@ -98,60 +96,73 @@ required: - channel0 - channel1 -if: - properties: - compatible: - contains: - enum: - - renesas,rzg2l-canfd -then: - properties: - interrupts: - items: - - description: CAN global error interrupt - - description: CAN receive FIFO interrupt - - description: CAN0 error interrupt - - description: CAN0 transmit interrupt - - description: CAN0 transmit/receive FIFO receive completion interrupt - - description: CAN1 error interrupt - - description: CAN1 transmit interrupt - - description: CAN1 transmit/receive FIFO receive completion interrupt - - interrupt-names: - items: - - const: g_err - - const: g_recc - - const: ch0_err - - const: ch0_rec - - const: ch0_trx - - const: ch1_err - - const: ch1_rec - - const: ch1_trx - - resets: - maxItems: 2 - - reset-names: - items: - - const: rstp_n - - const: rstc_n - - required: - - reset-names -else: - properties: - interrupts: - items: - - description: Channel interrupt - - description: Global interrupt - - interrupt-names: - items: - - const: ch_int - - const: g_int - - resets: - maxItems: 1 +allOf: + - $ref: can-controller.yaml# + + - if: + properties: + compatible: + contains: + enum: + - renesas,rzg2l-canfd + then: + properties: + interrupts: + items: + - description: CAN global error interrupt + - description: CAN receive FIFO interrupt + - description: CAN0 error interrupt + - description: CAN0 transmit interrupt + - description: CAN0 transmit/receive FIFO receive completion interrupt + - description: CAN1 error interrupt + - description: CAN1 transmit interrupt + - description: CAN1 transmit/receive FIFO receive completion interrupt + + interrupt-names: + items: + - const: g_err + - const: g_recc + - const: ch0_err + - const: ch0_rec + - const: ch0_trx + - const: ch1_err + - const: ch1_rec + - const: ch1_trx + + resets: + maxItems: 2 + + reset-names: + items: + - const: rstp_n + - const: rstc_n + + required: + - reset-names + else: + properties: + interrupts: + items: + - description: Channel interrupt + - description: Global interrupt + + interrupt-names: + items: + - const: ch_int + - const: g_int + + resets: + maxItems: 1 + + - if: + not: + properties: + compatible: + contains: + const: renesas,r8a779a0-canfd + then: + patternProperties: + "^channel[2-7]$": false unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml index 10ad7e71097b..9abb8eba5fad 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -19,7 +19,8 @@ allOf: properties: reg: - description: Port number + items: + - description: Port number label: description: diff --git a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml index 73b774eadd0b..1d7dab31457d 100644 --- a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml +++ b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml @@ -12,7 +12,7 @@ allOf: maintainers: - Andrew Lunn <andrew@lunn.ch> - Florian Fainelli <f.fainelli@gmail.com> - - Vivien Didelot <vivien.didelot@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> - Kurt Kanzenbach <kurt@linutronix.de> description: diff --git a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml index 7ca9c19a157c..0a0d62b6c00e 100644 --- a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml +++ b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml @@ -74,10 +74,10 @@ properties: properties: pcs-handle: + maxItems: 1 description: phandle pointing to a PCS sub-node compatible with renesas,rzn1-miic.yaml# - $ref: /schemas/types.yaml#/definitions/phandle unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml index 4b3c590fcebf..3aef506fa158 100644 --- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml @@ -108,11 +108,17 @@ properties: $ref: "#/properties/phy-connection-type" pcs-handle: - $ref: /schemas/types.yaml#/definitions/phandle + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + maxItems: 1 description: Specifies a reference to a node representing a PCS PHY device on a MDIO bus to link with an external PHY (phy-handle) if exists. + pcs-handle-names: + description: + The name of each PCS in pcs-handle. + phy-handle: $ref: /schemas/types.yaml#/definitions/phandle description: @@ -216,6 +222,9 @@ properties: required: - speed +dependencies: + pcs-handle-names: [pcs-handle] + allOf: - if: properties: diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml index e0f376f7e274..77e5f32cb62f 100644 --- a/Documentation/devicetree/bindings/net/fsl,fec.yaml +++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml @@ -7,7 +7,9 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Freescale Fast Ethernet Controller (FEC) maintainers: - - Joakim Zhang <qiangqing.zhang@nxp.com> + - Shawn Guo <shawnguo@kernel.org> + - Wei Fang <wei.fang@nxp.com> + - NXP Linux Team <linux-imx@nxp.com> allOf: - $ref: ethernet-controller.yaml# diff --git a/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml b/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml index 3a35ac1c260d..c80c880a9dab 100644 --- a/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml +++ b/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml @@ -85,9 +85,39 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle description: A reference to the IEEE1588 timer + phys: + description: A reference to the SerDes lane(s) + maxItems: 1 + + phy-names: + items: + - const: serdes + pcsphy-handle: - $ref: /schemas/types.yaml#/definitions/phandle - description: A reference to the PCS (typically found on the SerDes) + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + maxItems: 3 + deprecated: true + description: See pcs-handle. + + pcs-handle: + minItems: 1 + maxItems: 3 + description: | + A reference to the various PCSs (typically found on the SerDes). If + pcs-handle-names is absent, and phy-connection-type is "xgmii", then the first + reference will be assumed to be for "xfi". Otherwise, if pcs-handle-names is + absent, then the first reference will be assumed to be for "sgmii". + + pcs-handle-names: + minItems: 1 + maxItems: 3 + items: + enum: + - sgmii + - qsgmii + - xfi + description: The type of each PCS in pcsphy-handle. tbi-handle: $ref: /schemas/types.yaml#/definitions/phandle @@ -100,6 +130,10 @@ required: - fsl,fman-ports - ptp-timer +dependencies: + pcs-handle-names: + - pcs-handle + allOf: - $ref: ethernet-controller.yaml# - if: @@ -110,14 +144,6 @@ allOf: then: required: - tbi-handle - - if: - properties: - compatible: - contains: - const: fsl,fman-memac - then: - required: - - pcsphy-handle unevaluatedProperties: false @@ -138,8 +164,9 @@ examples: reg = <0xe8000 0x1000>; fsl,fman-ports = <&fman0_rx_0x0c &fman0_tx_0x2c>; ptp-timer = <&ptp_timer0>; - pcsphy-handle = <&pcsphy4>; - phy-handle = <&sgmii_phy1>; - phy-connection-type = "sgmii"; + pcs-handle = <&pcsphy4>, <&qsgmiib_pcs1>; + pcs-handle-names = "sgmii", "qsgmii"; + phys = <&serdes1 1>; + phy-names = "serdes"; }; ... diff --git a/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml b/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml index 7f620a71a972..600240281e8c 100644 --- a/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml +++ b/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml @@ -31,7 +31,7 @@ properties: phy-mode: true pcs-handle: - $ref: /schemas/types.yaml#/definitions/phandle + maxItems: 1 description: A reference to a node representing a PCS PHY device found on the internal MDIO bus. diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt index b9055335db3b..bda4b41af074 100644 --- a/Documentation/devicetree/bindings/net/fsl-fman.txt +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -320,8 +320,9 @@ For internal PHY device on internal mdio bus, a PHY node should be created. See the definition of the PHY node in booting-without-of.txt for an example of how to define a PHY (Internal PHY has no interrupt line). - For "fsl,fman-mdio" compatible internal mdio bus, the PHY is TBI PHY. -- For "fsl,fman-memac-mdio" compatible internal mdio bus, the PHY is PCS PHY, - PCS PHY addr must be '0'. +- For "fsl,fman-memac-mdio" compatible internal mdio bus, the PHY is PCS PHY. + The PCS PHY address should correspond to the value of the appropriate + MDEV_PORT. EXAMPLE diff --git a/Documentation/devicetree/bindings/net/marvell,dfx-server.yaml b/Documentation/devicetree/bindings/net/marvell,dfx-server.yaml new file mode 100644 index 000000000000..8a14c919e3f7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,dfx-server.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/marvell,dfx-server.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Prestera DFX server + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +select: + properties: + compatible: + contains: + const: marvell,dfx-server + required: + - compatible + +properties: + compatible: + items: + - const: marvell,dfx-server + - const: simple-bus + + reg: + maxItems: 1 + + ranges: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + +required: + - compatible + - reg + - ranges + +# The DFX server may expose clocks described as subnodes +additionalProperties: + type: object + +examples: + - | + + #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + bus@0 { + reg = <0 0>; + #address-cells = <2>; + #size-cells = <1>; + + dfx-bus@ac000000 { + compatible = "marvell,dfx-server", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>; + reg = <MBUS_ID(0x08, 0x00) 0 0x100000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,pp2.yaml b/Documentation/devicetree/bindings/net/marvell,pp2.yaml new file mode 100644 index 000000000000..4eadafc43d4f --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,pp2.yaml @@ -0,0 +1,305 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/marvell,pp2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell CN913X / Marvell Armada 375, 7K, 8K Ethernet Controller + +maintainers: + - Marcin Wojtas <mw@semihalf.com> + - Russell King <linux@armlinux.org> + +description: | + Marvell Armada 375 Ethernet Controller (PPv2.1) + Marvell Armada 7K/8K Ethernet Controller (PPv2.2) + Marvell CN913X Ethernet Controller (PPv2.3) + +properties: + compatible: + enum: + - marvell,armada-375-pp2 + - marvell,armada-7k-pp22 + + reg: + minItems: 3 + maxItems: 4 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + clocks: + minItems: 2 + items: + - description: main controller clock + - description: GOP clock + - description: MG clock + - description: MG Core clock + - description: AXI clock + + clock-names: + minItems: 2 + items: + - const: pp_clk + - const: gop_clk + - const: mg_clk + - const: mg_core_clk + - const: axi_clk + + dma-coherent: true + + marvell,system-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the system controller. + +patternProperties: + '^(ethernet-)?port@[0-2]$': + type: object + description: subnode for each ethernet port. + $ref: ethernet-controller.yaml# + unevaluatedProperties: false + + properties: + reg: + description: ID of the port from the MAC point of view. + maximum: 2 + + interrupts: + minItems: 1 + maxItems: 10 + description: interrupt(s) for the port + + interrupt-names: + minItems: 1 + items: + - const: hif0 + - const: hif1 + - const: hif2 + - const: hif3 + - const: hif4 + - const: hif5 + - const: hif6 + - const: hif7 + - const: hif8 + - const: link + + description: > + if more than a single interrupt for is given, must be the + name associated to the interrupts listed. Valid names are: + "hifX", with X in [0..8], and "link". The names "tx-cpu0", + "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported + for backward compatibility but shouldn't be used for new + additions. + + phys: + minItems: 1 + maxItems: 2 + description: > + Generic PHY, providing SerDes connectivity. For most modes, + one lane is sufficient, but some (e.g. RXAUI) may require two. + + phy-mode: + enum: + - gmii + - sgmii + - rgmii-id + - 1000base-x + - 2500base-x + - 5gbase-r + - rxaui + - 10gbase-r + + port-id: + $ref: /schemas/types.yaml#/definitions/uint32 + deprecated: true + description: > + ID of the port from the MAC point of view. + Legacy binding for backward compatibility. + + marvell,loopback: + $ref: /schemas/types.yaml#/definitions/flag + description: port is loopback mode. + + gop-port-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: > + only for marvell,armada-7k-pp22, ID of the port from the + GOP (Group Of Ports) point of view. This ID is used to index the + per-port registers in the second register area. + + required: + - reg + - interrupts + - phy-mode + - port-id + +required: + - compatible + - reg + - clocks + - clock-names + +allOf: + - if: + properties: + compatible: + const: marvell,armada-7k-pp22 + then: + properties: + reg: + items: + - description: Packet Processor registers + - description: Networking interfaces registers + - description: CM3 address space used for TX Flow Control + + clocks: + minItems: 5 + + clock-names: + minItems: 5 + + patternProperties: + '^(ethernet-)?port@[0-2]$': + required: + - gop-port-id + + required: + - marvell,system-controller + else: + properties: + reg: + items: + - description: Packet Processor registers + - description: LMS registers + - description: Register area per eth0 + - description: Register area per eth1 + + clocks: + maxItems: 2 + + clock-names: + maxItems: 2 + + patternProperties: + '^(ethernet-)?port@[0-1]$': + properties: + reg: + maximum: 1 + + gop-port-id: false + +additionalProperties: false + +examples: + - | + // For Armada 375 variant + #include <dt-bindings/interrupt-controller/mvebu-icu.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + ethernet@f0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,armada-375-pp2"; + reg = <0xf0000 0xa000>, + <0xc0000 0x3060>, + <0xc4000 0x100>, + <0xc5000 0x100>; + clocks = <&gateclk 3>, <&gateclk 19>; + clock-names = "pp_clk", "gop_clk"; + + ethernet-port@0 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + reg = <0>; + port-id = <0>; /* For backward compatibility. */ + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + ethernet-port@1 { + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + reg = <1>; + port-id = <1>; /* For backward compatibility. */ + phy = <&phy3>; + phy-mode = "gmii"; + }; + }; + + - | + // For Armada 7k/8k and Cn913x variants + #include <dt-bindings/interrupt-controller/mvebu-icu.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + ethernet@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>, <0x220000 0x800>; + clocks = <&cp0_clk 1 3>, <&cp0_clk 1 9>, + <&cp0_clk 1 5>, <&cp0_clk 1 6>, <&cp0_clk 1 18>; + clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk"; + marvell,system-controller = <&cp0_syscon0>; + + ethernet-port@0 { + interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; + phy-mode = "10gbase-r"; + phys = <&cp0_comphy4 0>; + reg = <0>; + port-id = <0>; /* For backward compatibility. */ + gop-port-id = <0>; + }; + + ethernet-port@1 { + interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; + phy-mode = "rgmii-id"; + reg = <1>; + port-id = <1>; /* For backward compatibility. */ + gop-port-id = <2>; + }; + + ethernet-port@2 { + interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; + phy-mode = "2500base-x"; + managed = "in-band-status"; + phys = <&cp0_comphy5 2>; + sfp = <&sfp_eth3>; + reg = <2>; + port-id = <2>; /* For backward compatibility. */ + gop-port-id = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt deleted file mode 100644 index e28938ddfdf5..000000000000 --- a/Documentation/devicetree/bindings/net/marvell,prestera.txt +++ /dev/null @@ -1,81 +0,0 @@ -Marvell Prestera Switch Chip bindings -------------------------------------- - -Required properties: -- compatible: must be "marvell,prestera" and one of the following - "marvell,prestera-98dx3236", - "marvell,prestera-98dx3336", - "marvell,prestera-98dx4251", -- reg: address and length of the register set for the device. -- interrupts: interrupt for the device - -Optional properties: -- dfx: phandle reference to the "DFX Server" node - -Example: - -switch { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>; - - packet-processor@0 { - compatible = "marvell,prestera-98dx3236", "marvell,prestera"; - reg = <0 0x4000000>; - interrupts = <33>, <34>, <35>; - dfx = <&dfx>; - }; -}; - -DFX Server bindings -------------------- - -Required properties: -- compatible: must be "marvell,dfx-server", "simple-bus" -- ranges: describes the address mapping of a memory-mapped bus. -- reg: address and length of the register set for the device. - -Example: - -dfx-server { - compatible = "marvell,dfx-server", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>; - reg = <MBUS_ID(0x08, 0x00) 0 0x100000>; -}; - -Marvell Prestera SwitchDev bindings ------------------------------------ -Optional properties: -- compatible: must be "marvell,prestera" -- base-mac-provider: describes handle to node which provides base mac address, - might be a static base mac address or nvme cell provider. - -Example: - -eeprom_mac_addr: eeprom-mac-addr { - compatible = "eeprom,mac-addr-cell"; - status = "okay"; - - nvmem = <&eeprom_at24>; -}; - -prestera { - compatible = "marvell,prestera"; - status = "okay"; - - base-mac-provider = <&eeprom_mac_addr>; -}; - -The current implementation of Prestera Switchdev PCI interface driver requires -that BAR2 is assigned to 0xf6000000 as base address from the PCI IO range: - -&cp0_pcie0 { - ranges = <0x81000000 0x0 0xfb000000 0x0 0xfb000000 0x0 0xf0000 - 0x82000000 0x0 0xf6000000 0x0 0xf6000000 0x0 0x2000000 - 0x82000000 0x0 0xf9000000 0x0 0xf9000000 0x0 0x100000>; - phys = <&cp0_comphy0 0>; - status = "okay"; -}; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.yaml b/Documentation/devicetree/bindings/net/marvell,prestera.yaml new file mode 100644 index 000000000000..5ea8b73663a5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,prestera.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/marvell,prestera.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Prestera switch family + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - marvell,prestera-98dx3236 + - marvell,prestera-98dx3336 + - marvell,prestera-98dx4251 + - const: marvell,prestera + - enum: + - pci11ab,c804 + - pci11ab,c80c + - pci11ab,cc1e + + reg: + maxItems: 1 + + interrupts: + maxItems: 3 + + dfx: + description: Reference to the DFX Server bus node. + $ref: /schemas/types.yaml#/definitions/phandle + + nvmem-cells: true + + nvmem-cell-names: true + +if: + properties: + compatible: + contains: + const: marvell,prestera + +# Memory mapped AlleyCat3 family +then: + properties: + nvmem-cells: false + nvmem-cell-names: false + required: + - interrupts + +# PCI Aldrin family +else: + properties: + interrupts: false + dfx: false + +required: + - compatible + - reg + +# Ports can also be described +additionalProperties: + type: object + +examples: + - | + packet-processor@0 { + compatible = "marvell,prestera-98dx3236", "marvell,prestera"; + reg = <0 0x4000000>; + interrupts = <33>, <34>, <35>; + dfx = <&dfx>; + }; + + - | + pcie@0 { + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x0 0x0 0x0>; + reg = <0x0 0x0 0x0 0x0 0x0 0x0>; + device_type = "pci"; + + switch@0,0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + compatible = "pci11ab,c80c"; + nvmem-cells = <&mac_address 0>; + nvmem-cell-names = "mac-address"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt deleted file mode 100644 index ce15c173f43f..000000000000 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ /dev/null @@ -1,141 +0,0 @@ -* Marvell Armada 375 Ethernet Controller (PPv2.1) - Marvell Armada 7K/8K Ethernet Controller (PPv2.2) - Marvell CN913X Ethernet Controller (PPv2.3) - -Required properties: - -- compatible: should be one of: - "marvell,armada-375-pp2" - "marvell,armada-7k-pp2" -- reg: addresses and length of the register sets for the device. - For "marvell,armada-375-pp2", must contain the following register - sets: - - common controller registers - - LMS registers - - one register area per Ethernet port - For "marvell,armada-7k-pp2" used by 7K/8K and CN913X, must contain the following register - sets: - - packet processor registers - - networking interfaces registers - - CM3 address space used for TX Flow Control - -- clocks: pointers to the reference clocks for this device, consequently: - - main controller clock (for both armada-375-pp2 and armada-7k-pp2) - - GOP clock (for both armada-375-pp2 and armada-7k-pp2) - - MG clock (only for armada-7k-pp2) - - MG Core clock (only for armada-7k-pp2) - - AXI clock (only for armada-7k-pp2) -- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk", - "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2). - -The ethernet ports are represented by subnodes. At least one port is -required. - -Required properties (port): - -- interrupts: interrupt(s) for the port -- port-id: ID of the port from the MAC point of view -- gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the - GOP (Group Of Ports) point of view. This ID is used to index the - per-port registers in the second register area. -- phy-mode: See ethernet.txt file in the same directory - -Optional properties (port): - -- marvell,loopback: port is loopback mode -- phy: a phandle to a phy node defining the PHY address (as the reg - property, a single integer). -- interrupt-names: if more than a single interrupt for is given, must be the - name associated to the interrupts listed. Valid names are: - "hifX", with X in [0..8], and "link". The names "tx-cpu0", - "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported - for backward compatibility but shouldn't be used for new - additions. -- marvell,system-controller: a phandle to the system controller. - -Example for marvell,armada-375-pp2: - -ethernet@f0000 { - compatible = "marvell,armada-375-pp2"; - reg = <0xf0000 0xa000>, - <0xc0000 0x3060>, - <0xc4000 0x100>, - <0xc5000 0x100>; - clocks = <&gateclk 3>, <&gateclk 19>; - clock-names = "pp_clk", "gop_clk"; - - eth0: eth0@c4000 { - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; - port-id = <0>; - phy = <&phy0>; - phy-mode = "gmii"; - }; - - eth1: eth1@c5000 { - interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; - port-id = <1>; - phy = <&phy3>; - phy-mode = "gmii"; - }; -}; - -Example for marvell,armada-7k-pp2: - -cpm_ethernet: ethernet@0 { - compatible = "marvell,armada-7k-pp22"; - reg = <0x0 0x100000>, <0x129000 0xb000>, <0x220000 0x800>; - clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, - <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>; - clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk"; - - eth0: eth0 { - interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", - "hif5", "hif6", "hif7", "hif8", "link"; - port-id = <0>; - gop-port-id = <0>; - }; - - eth1: eth1 { - interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", - "hif5", "hif6", "hif7", "hif8", "link"; - port-id = <1>; - gop-port-id = <2>; - }; - - eth2: eth2 { - interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", - "hif5", "hif6", "hif7", "hif8", "link"; - port-id = <2>; - gop-port-id = <3>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml b/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml index cf91fecd8909..3715c5f8f0e0 100644 --- a/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml +++ b/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml @@ -39,7 +39,9 @@ properties: - usb424,9e08 # SMSC LAN89530 USB Ethernet Device - usb424,ec00 # SMSC9512/9514 USB Hub & Ethernet Device - reg: true + reg: + maxItems: 1 + local-mac-address: true mac-address: true diff --git a/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml b/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml index b2558421268a..6924aff0b2c5 100644 --- a/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml +++ b/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml @@ -14,7 +14,9 @@ properties: oneOf: - const: nxp,nxp-nci-i2c - items: - - const: nxp,pn547 + - enum: + - nxp,nq310 + - nxp,pn547 - const: nxp,nxp-nci-i2c enable-gpios: diff --git a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml index 0270b0ca166b..04df496af7e6 100644 --- a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +++ b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml @@ -7,7 +7,9 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: NXP i.MX8 DWMAC glue layer maintainers: - - Joakim Zhang <qiangqing.zhang@nxp.com> + - Clark Wang <xiaoning.wang@nxp.com> + - Shawn Guo <shawnguo@kernel.org> + - NXP Linux Team <linux-imx@nxp.com> # We need a select here so we don't match all nodes with 'snps,dwmac' select: diff --git a/Documentation/devicetree/bindings/net/pcs/fsl,lynx-pcs.yaml b/Documentation/devicetree/bindings/net/pcs/fsl,lynx-pcs.yaml new file mode 100644 index 000000000000..fbedf696c555 --- /dev/null +++ b/Documentation/devicetree/bindings/net/pcs/fsl,lynx-pcs.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/pcs/fsl,lynx-pcs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP Lynx PCS + +maintainers: + - Ioana Ciornei <ioana.ciornei@nxp.com> + +description: | + NXP Lynx 10G and 28G SerDes have Ethernet PCS devices which can be used as + protocol controllers. They are accessible over the Ethernet interface's MDIO + bus. + +properties: + compatible: + const: fsl,lynx-pcs + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + qsgmii_pcs1: ethernet-pcs@1 { + compatible = "fsl,lynx-pcs"; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.yaml b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml index 1ebf9e8c8a1d..89f94b31b546 100644 --- a/Documentation/devicetree/bindings/net/qca,ar71xx.yaml +++ b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml @@ -123,7 +123,6 @@ examples: switch_port0: port@0 { reg = <0x0>; - label = "cpu"; ethernet = <ð1>; phy-mode = "gmii"; diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index dd4bb2e74880..4aeda379726f 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -49,6 +49,7 @@ properties: - qcom,sc7280-ipa - qcom,sdm845-ipa - qcom,sdx55-ipa + - qcom,sm6350-ipa - qcom,sm8350-ipa reg: @@ -124,19 +125,31 @@ properties: - const: ipa-clock-enabled-valid - const: ipa-clock-enabled + qcom,gsi-loader: + enum: + - self + - modem + - skip + description: + Indicates how GSI firmware should be loaded. If the AP loads + and validates GSI firmware, this property has value "self". + If the modem does this, this property has value "modem". + Otherwise, "skip" means GSI firmware loading is not required. + modem-init: + deprecated: true type: boolean description: - If present, it indicates that the modem is responsible for - performing early IPA initialization, including loading and - validating firwmare used by the GSI. + This is the older (deprecated) way of indicating how GSI firmware + should be loaded. If present, the modem loads GSI firmware; if + absent, the AP loads GSI firmware. memory-region: maxItems: 1 description: If present, a phandle for a reserved memory area that holds the firmware passed to Trust Zone for authentication. Required - when Trust Zone (not the modem) performs early initialization. + when the AP (not the modem) performs early initialization. firmware-name: $ref: /schemas/types.yaml#/definitions/string @@ -155,22 +168,36 @@ required: - interconnects - qcom,smem-states -# Either modem-init is present, or memory-region must be present. -oneOf: - - required: - - modem-init - - required: - - memory-region - -# If memory-region is present, firmware-name may optionally be present. -# But if modem-init is present, firmware-name must not be present. -if: - required: - - modem-init -then: - not: - required: - - firmware-name +allOf: + # If qcom,gsi-loader is present, modem-init must not be present + - if: + required: + - qcom,gsi-loader + then: + properties: + modem-init: false + + # If qcom,gsi-loader is "self", the AP loads GSI firmware, and + # memory-region must be specified + if: + properties: + qcom,gsi-loader: + contains: + const: self + then: + required: + - memory-region + else: + # If qcom,gsi-loader is not present, we use deprecated behavior. + # If modem-init is not present, the AP loads GSI firmware, and + # memory-region must be specified. + if: + not: + required: + - modem-init + then: + required: + - memory-region additionalProperties: false @@ -201,14 +228,17 @@ examples: }; ipa@1e40000 { - compatible = "qcom,sdm845-ipa"; + compatible = "qcom,sc7180-ipa"; - modem-init; + qcom,gsi-loader = "self"; + memory-region = <&ipa_fw_mem>; + firmware-name = "qcom/sc7180-trogdor/modem/modem.mdt"; - iommus = <&apps_smmu 0x720 0x3>; + iommus = <&apps_smmu 0x440 0x0>, + <&apps_smmu 0x442 0x0>; reg = <0x1e40000 0x7000>, - <0x1e47000 0x2000>, - <0x1e04000 0x2c000>; + <0x1e47000 0x2000>, + <0x1e04000 0x2c000>; reg-names = "ipa-reg", "ipa-shared", "gsi"; @@ -226,9 +256,9 @@ examples: clock-names = "core"; interconnects = - <&rsc_hlos MASTER_IPA &rsc_hlos SLAVE_EBI1>, - <&rsc_hlos MASTER_IPA &rsc_hlos SLAVE_IMEM>, - <&rsc_hlos MASTER_APPSS_PROC &rsc_hlos SLAVE_IPA_CFG>; + <&aggre2_noc MASTER_IPA 0 &mc_virt SLAVE_EBI1 0>, + <&aggre2_noc MASTER_IPA 0 &system_noc SLAVE_IMEM 0>, + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>; interconnect-names = "memory", "imem", "config"; diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml index ad8b2b41c140..7631ecc8fd01 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml @@ -9,14 +9,18 @@ title: Qualcomm IPQ40xx MDIO Controller maintainers: - Robert Marko <robert.marko@sartura.hr> -allOf: - - $ref: "mdio.yaml#" - properties: compatible: - enum: - - qcom,ipq4019-mdio - - qcom,ipq5018-mdio + oneOf: + - enum: + - qcom,ipq4019-mdio + - qcom,ipq5018-mdio + + - items: + - enum: + - qcom,ipq6018-mdio + - qcom,ipq8074-mdio + - const: qcom,ipq4019-mdio "#address-cells": const: 1 @@ -33,10 +37,12 @@ properties: address range is only required by the platform IPQ50xx. clocks: - maxItems: 1 - description: | - MDIO clock source frequency fixed to 100MHZ, this clock should be specified - by the platform IPQ807x, IPQ60xx and IPQ50xx. + items: + - description: MDIO clock source frequency fixed to 100MHZ + + clock-names: + items: + - const: gcc_mdio_ahb_clk required: - compatible @@ -44,6 +50,26 @@ required: - "#address-cells" - "#size-cells" +allOf: + - $ref: "mdio.yaml#" + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq5018-mdio + - qcom,ipq6018-mdio + - qcom,ipq8074-mdio + then: + required: + - clocks + - clock-names + else: + properties: + clocks: false + clock-names: false + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml index e329ef06e10f..143b5667abad 100644 --- a/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml +++ b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml @@ -20,6 +20,7 @@ properties: enum: - realtek,rtl8723bs-bt - realtek,rtl8723cs-bt + - realtek,rtl8723ds-bt - realtek,rtl8822cs-bt device-wake-gpios: diff --git a/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml b/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml new file mode 100644 index 000000000000..e933a1e48d67 --- /dev/null +++ b/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml @@ -0,0 +1,262 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/renesas,r8a779f0-ether-switch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Ethernet Switch + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +properties: + compatible: + const: renesas,r8a779f0-ether-switch + + reg: + maxItems: 2 + + reg-names: + items: + - const: base + - const: secure_base + + interrupts: + maxItems: 47 + + interrupt-names: + items: + - const: mfwd_error + - const: race_error + - const: coma_error + - const: gwca0_error + - const: gwca1_error + - const: etha0_error + - const: etha1_error + - const: etha2_error + - const: gptp0_status + - const: gptp1_status + - const: mfwd_status + - const: race_status + - const: coma_status + - const: gwca0_status + - const: gwca1_status + - const: etha0_status + - const: etha1_status + - const: etha2_status + - const: rmac0_status + - const: rmac1_status + - const: rmac2_status + - const: gwca0_rxtx0 + - const: gwca0_rxtx1 + - const: gwca0_rxtx2 + - const: gwca0_rxtx3 + - const: gwca0_rxtx4 + - const: gwca0_rxtx5 + - const: gwca0_rxtx6 + - const: gwca0_rxtx7 + - const: gwca1_rxtx0 + - const: gwca1_rxtx1 + - const: gwca1_rxtx2 + - const: gwca1_rxtx3 + - const: gwca1_rxtx4 + - const: gwca1_rxtx5 + - const: gwca1_rxtx6 + - const: gwca1_rxtx7 + - const: gwca0_rxts0 + - const: gwca0_rxts1 + - const: gwca1_rxts0 + - const: gwca1_rxts1 + - const: rmac0_mdio + - const: rmac1_mdio + - const: rmac2_mdio + - const: rmac0_phy + - const: rmac1_phy + - const: rmac2_phy + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + iommus: + maxItems: 16 + + power-domains: + maxItems: 1 + + ethernet-ports: + type: object + additionalProperties: false + + properties: + '#address-cells': + description: Port number of ETHA (TSNA). + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + "^port@[0-9a-f]+$": + type: object + $ref: /schemas/net/ethernet-controller.yaml# + unevaluatedProperties: false + + properties: + reg: + maxItems: 1 + description: + Port number of ETHA (TSNA). + + phys: + maxItems: 1 + description: + Phandle of an Ethernet SERDES. + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + required: + - reg + - phy-handle + - phy-mode + - phys + - mdio + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - resets + - power-domains + - ethernet-ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779f0-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a779f0-sysc.h> + + ethernet@e6880000 { + compatible = "renesas,r8a779f0-ether-switch"; + reg = <0xe6880000 0x20000>, <0xe68c0000 0x20000>; + reg-names = "base", "secure_base"; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 289 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 291 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mfwd_error", "race_error", + "coma_error", "gwca0_error", + "gwca1_error", "etha0_error", + "etha1_error", "etha2_error", + "gptp0_status", "gptp1_status", + "mfwd_status", "race_status", + "coma_status", "gwca0_status", + "gwca1_status", "etha0_status", + "etha1_status", "etha2_status", + "rmac0_status", "rmac1_status", + "rmac2_status", + "gwca0_rxtx0", "gwca0_rxtx1", + "gwca0_rxtx2", "gwca0_rxtx3", + "gwca0_rxtx4", "gwca0_rxtx5", + "gwca0_rxtx6", "gwca0_rxtx7", + "gwca1_rxtx0", "gwca1_rxtx1", + "gwca1_rxtx2", "gwca1_rxtx3", + "gwca1_rxtx4", "gwca1_rxtx5", + "gwca1_rxtx6", "gwca1_rxtx7", + "gwca0_rxts0", "gwca0_rxts1", + "gwca1_rxts0", "gwca1_rxts1", + "rmac0_mdio", "rmac1_mdio", + "rmac2_mdio", + "rmac0_phy", "rmac1_phy", + "rmac2_phy"; + clocks = <&cpg CPG_MOD 1505>; + power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>; + resets = <&cpg 1505>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phy-handle = <ð_phy0>; + phy-mode = "sgmii"; + phys = <ð_serdes 0>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + port@1 { + reg = <1>; + phy-handle = <ð_phy1>; + phy-mode = "sgmii"; + phys = <ð_serdes 1>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + port@2 { + reg = <2>; + phy-handle = <ð_phy2>; + phy-mode = "sgmii"; + phys = <ð_serdes 2>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.yaml b/Documentation/devicetree/bindings/net/sff,sfp.yaml index 06c66ab81c01..231c4d75e4b1 100644 --- a/Documentation/devicetree/bindings/net/sff,sfp.yaml +++ b/Documentation/devicetree/bindings/net/sff,sfp.yaml @@ -22,7 +22,8 @@ properties: phandle of an I2C bus controller for the SFP two wire serial maximum-power-milliwatt: - maxItems: 1 + minimum: 1000 + default: 1000 description: Maximum module power consumption Specifies the maximum power consumption allowable by a module in the slot, in milli-Watts. Presently, modules can diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml index 13b984076af5..e88a86623fce 100644 --- a/Documentation/devicetree/bindings/net/snps,dwmac.yaml +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -167,56 +167,238 @@ properties: snps,mtl-rx-config: $ref: /schemas/types.yaml#/definitions/phandle description: - Multiple RX Queues parameters. Phandle to a node that can - contain the following properties - * snps,rx-queues-to-use, number of RX queues to be used in the - driver - * Choose one of these RX scheduling algorithms - * snps,rx-sched-sp, Strict priority - * snps,rx-sched-wsp, Weighted Strict priority - * For each RX queue - * Choose one of these modes - * snps,dcb-algorithm, Queue to be enabled as DCB - * snps,avb-algorithm, Queue to be enabled as AVB - * snps,map-to-dma-channel, Channel to map - * Specifiy specific packet routing - * snps,route-avcp, AV Untagged Control packets - * snps,route-ptp, PTP Packets - * snps,route-dcbcp, DCB Control Packets - * snps,route-up, Untagged Packets - * snps,route-multi-broad, Multicast & Broadcast Packets - * snps,priority, bitmask of the tagged frames priorities assigned to - the queue + Multiple RX Queues parameters. Phandle to a node that + implements the 'rx-queues-config' object described in + this binding. + + rx-queues-config: + type: object + properties: + snps,rx-queues-to-use: + $ref: /schemas/types.yaml#/definitions/uint32 + description: number of RX queues to be used in the driver + snps,rx-sched-sp: + type: boolean + description: Strict priority + snps,rx-sched-wsp: + type: boolean + description: Weighted Strict priority + allOf: + - if: + required: + - snps,rx-sched-sp + then: + properties: + snps,rx-sched-wsp: false + - if: + required: + - snps,rx-sched-wsp + then: + properties: + snps,rx-sched-sp: false + patternProperties: + "^queue[0-9]$": + description: Each subnode represents a queue. + type: object + properties: + snps,dcb-algorithm: + type: boolean + description: Queue to be enabled as DCB + snps,avb-algorithm: + type: boolean + description: Queue to be enabled as AVB + snps,map-to-dma-channel: + $ref: /schemas/types.yaml#/definitions/uint32 + description: DMA channel id to map + snps,route-avcp: + type: boolean + description: AV Untagged Control packets + snps,route-ptp: + type: boolean + description: PTP Packets + snps,route-dcbcp: + type: boolean + description: DCB Control Packets + snps,route-up: + type: boolean + description: Untagged Packets + snps,route-multi-broad: + type: boolean + description: Multicast & Broadcast Packets + snps,priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Bitmask of the tagged frames priorities assigned to the queue + allOf: + - if: + required: + - snps,dcb-algorithm + then: + properties: + snps,avb-algorithm: false + - if: + required: + - snps,avb-algorithm + then: + properties: + snps,dcb-algorithm: false + - if: + required: + - snps,route-avcp + then: + properties: + snps,route-ptp: false + snps,route-dcbcp: false + snps,route-up: false + snps,route-multi-broad: false + - if: + required: + - snps,route-ptp + then: + properties: + snps,route-avcp: false + snps,route-dcbcp: false + snps,route-up: false + snps,route-multi-broad: false + - if: + required: + - snps,route-dcbcp + then: + properties: + snps,route-avcp: false + snps,route-ptp: false + snps,route-up: false + snps,route-multi-broad: false + - if: + required: + - snps,route-up + then: + properties: + snps,route-avcp: false + snps,route-ptp: false + snps,route-dcbcp: false + snps,route-multi-broad: false + - if: + required: + - snps,route-multi-broad + then: + properties: + snps,route-avcp: false + snps,route-ptp: false + snps,route-dcbcp: false + snps,route-up: false + additionalProperties: false + additionalProperties: false snps,mtl-tx-config: $ref: /schemas/types.yaml#/definitions/phandle description: - Multiple TX Queues parameters. Phandle to a node that can - contain the following properties - * snps,tx-queues-to-use, number of TX queues to be used in the - driver - * Choose one of these TX scheduling algorithms - * snps,tx-sched-wrr, Weighted Round Robin - * snps,tx-sched-wfq, Weighted Fair Queuing - * snps,tx-sched-dwrr, Deficit Weighted Round Robin - * snps,tx-sched-sp, Strict priority - * For each TX queue - * snps,weight, TX queue weight (if using a DCB weight - algorithm) - * Choose one of these modes - * snps,dcb-algorithm, TX queue will be working in DCB - * snps,avb-algorithm, TX queue will be working in AVB - [Attention] Queue 0 is reserved for legacy traffic - and so no AVB is available in this queue. - * Configure Credit Base Shaper (if AVB Mode selected) - * snps,send_slope, enable Low Power Interface - * snps,idle_slope, unlock on WoL - * snps,high_credit, max write outstanding req. limit - * snps,low_credit, max read outstanding req. limit - * snps,priority, bitmask of the priorities assigned to the queue. - When a PFC frame is received with priorities matching the bitmask, - the queue is blocked from transmitting for the pause time specified - in the PFC frame. + Multiple TX Queues parameters. Phandle to a node that + implements the 'tx-queues-config' object described in + this binding. + + tx-queues-config: + type: object + properties: + snps,tx-queues-to-use: + $ref: /schemas/types.yaml#/definitions/uint32 + description: number of TX queues to be used in the driver + snps,tx-sched-wrr: + type: boolean + description: Weighted Round Robin + snps,tx-sched-wfq: + type: boolean + description: Weighted Fair Queuing + snps,tx-sched-dwrr: + type: boolean + description: Deficit Weighted Round Robin + snps,tx-sched-sp: + type: boolean + description: Strict priority + allOf: + - if: + required: + - snps,tx-sched-wrr + then: + properties: + snps,tx-sched-wfq: false + snps,tx-sched-dwrr: false + snps,tx-sched-sp: false + - if: + required: + - snps,tx-sched-wfq + then: + properties: + snps,tx-sched-wrr: false + snps,tx-sched-dwrr: false + snps,tx-sched-sp: false + - if: + required: + - snps,tx-sched-dwrr + then: + properties: + snps,tx-sched-wrr: false + snps,tx-sched-wfq: false + snps,tx-sched-sp: false + - if: + required: + - snps,tx-sched-sp + then: + properties: + snps,tx-sched-wrr: false + snps,tx-sched-wfq: false + snps,tx-sched-dwrr: false + patternProperties: + "^queue[0-9]$": + description: Each subnode represents a queue. + type: object + properties: + snps,weight: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TX queue weight (if using a DCB weight algorithm) + snps,dcb-algorithm: + type: boolean + description: TX queue will be working in DCB + snps,avb-algorithm: + type: boolean + description: + TX queue will be working in AVB. + Queue 0 is reserved for legacy traffic and so no AVB is + available in this queue. + snps,send_slope: + $ref: /schemas/types.yaml#/definitions/uint32 + description: enable Low Power Interface + snps,idle_slope: + $ref: /schemas/types.yaml#/definitions/uint32 + description: unlock on WoL + snps,high_credit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: max write outstanding req. limit + snps,low_credit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: max read outstanding req. limit + snps,priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Bitmask of the tagged frames priorities assigned to the queue. + When a PFC frame is received with priorities matching the bitmask, + the queue is blocked from transmitting for the pause time specified + in the PFC frame. + allOf: + - if: + required: + - snps,dcb-algorithm + then: + properties: + snps,avb-algorithm: false + - if: + required: + - snps,avb-algorithm + then: + properties: + snps,dcb-algorithm: false + snps,weight: false + additionalProperties: false + additionalProperties: false snps,reset-gpio: deprecated: true @@ -463,41 +645,6 @@ additionalProperties: true examples: - | - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <0xf>; - snps,rd_osr_lmt = <0xf>; - snps,blen = <256 128 64 32 0 0 0>; - }; - - mtl_rx_setup: rx-queues-config { - snps,rx-queues-to-use = <1>; - snps,rx-sched-sp; - queue0 { - snps,dcb-algorithm; - snps,map-to-dma-channel = <0x0>; - snps,priority = <0x0>; - }; - }; - - mtl_tx_setup: tx-queues-config { - snps,tx-queues-to-use = <2>; - snps,tx-sched-wrr; - queue0 { - snps,weight = <0x10>; - snps,dcb-algorithm; - snps,priority = <0x0>; - }; - - queue1 { - snps,avb-algorithm; - snps,send_slope = <0x1000>; - snps,idle_slope = <0x1000>; - snps,high_credit = <0x3E800>; - snps,low_credit = <0xFFC18000>; - snps,priority = <0x1>; - }; - }; - gmac0: ethernet@e0800000 { compatible = "snps,dwxgmac-2.10", "snps,dwxgmac"; reg = <0xe0800000 0x8000>; @@ -516,6 +663,42 @@ examples: snps,axi-config = <&stmmac_axi_setup>; snps,mtl-rx-config = <&mtl_rx_setup>; snps,mtl-tx-config = <&mtl_tx_setup>; + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <256 128 64 32 0 0 0>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <2>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + + queue1 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3E800>; + snps,low_credit = <0xFFC18000>; + snps,priority = <0x1>; + }; + }; + mdio0 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/socionext,synquacer-netsec.yaml b/Documentation/devicetree/bindings/net/socionext,synquacer-netsec.yaml new file mode 100644 index 000000000000..a65e6aa215a7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,synquacer-netsec.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/socionext,synquacer-netsec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext NetSec Ethernet Controller IP + +maintainers: + - Jassi Brar <jaswinder.singh@linaro.org> + - Ilias Apalodimas <ilias.apalodimas@linaro.org> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + const: socionext,synquacer-netsec + + reg: + items: + - description: control register area + - description: EEPROM holding the MAC address and microengine firmware + + clocks: + maxItems: 1 + + clock-names: + const: phy_ref_clk + + dma-coherent: true + + interrupts: + maxItems: 1 + + mdio: + $ref: mdio.yaml# + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - mdio + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + ethernet@522d0000 { + compatible = "socionext,synquacer-netsec"; + reg = <0x522d0000 0x10000>, <0x10000000 0x10000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_netsec>; + clock-names = "phy_ref_clk"; + phy-mode = "rgmii"; + max-speed = <1000>; + max-frame-size = <9000>; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt deleted file mode 100644 index a3c1dffaa4bb..000000000000 --- a/Documentation/devicetree/bindings/net/socionext-netsec.txt +++ /dev/null @@ -1,56 +0,0 @@ -* Socionext NetSec Ethernet Controller IP - -Required properties: -- compatible: Should be "socionext,synquacer-netsec" -- reg: Address and length of the control register area, followed by the - address and length of the EEPROM holding the MAC address and - microengine firmware -- interrupts: Should contain ethernet controller interrupt -- clocks: phandle to the PHY reference clock -- clock-names: Should be "phy_ref_clk" -- phy-mode: See ethernet.txt file in the same directory -- phy-handle: See ethernet.txt in the same directory. - -- mdio device tree subnode: When the Netsec has a phy connected to its local - mdio, there must be device tree subnode with the following - required properties: - - - #address-cells: Must be <1>. - - #size-cells: Must be <0>. - - For each phy on the mdio bus, there must be a node with the following - fields: - - compatible: Refer to phy.txt - - reg: phy id used to communicate to phy. - -Optional properties: (See ethernet.txt file in the same directory) -- dma-coherent: Boolean property, must only be present if memory - accesses performed by the device are cache coherent. -- max-speed: See ethernet.txt in the same directory. -- max-frame-size: See ethernet.txt in the same directory. - -The MAC address will be determined using the optional properties -defined in ethernet.txt. The 'phy-mode' property is required, but may -be set to the empty string if the PHY configuration is programmed by -the firmware or set by hardware straps, and needs to be preserved. - -Example: - eth0: ethernet@522d0000 { - compatible = "socionext,synquacer-netsec"; - reg = <0 0x522d0000 0x0 0x10000>, <0 0x10000000 0x0 0x10000>; - interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_netsec>; - clock-names = "phy_ref_clk"; - phy-mode = "rgmii"; - max-speed = <1000>; - max-frame-size = <9000>; - phy-handle = <&phy1>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - phy1: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; - }; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 1aa4c6006cd0..80e505a2fda1 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -68,6 +68,8 @@ Optional properties: - mdio : Child node for MDIO bus. Must be defined if PHY access is required through the core's MDIO interface (i.e. always, unless the PHY is accessed through a different bus). + Non-standard MDIO bus frequency is supported via + "clock-frequency", see mdio.yaml. - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X modes, where "pcs-handle" should be used to point |