diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt')
-rw-r--r-- | Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt | 121 |
1 files changed, 0 insertions, 121 deletions
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt deleted file mode 100644 index 42d8814f903a..000000000000 --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt +++ /dev/null @@ -1,121 +0,0 @@ -MT8173 xHCI - -The device node for Mediatek SOC USB3.0 host controller - -There are two scenarios: the first one only supports xHCI driver; -the second one supports dual-role mode, and the host is based on xHCI -driver. Take account of backward compatibility, we divide bindings -into two parts. - -1st: only supports xHCI driver ------------------------------------------------------------------------- - -Required properties: - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in - addition, one of: - - "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control - - interrupts : interrupt used by the controller - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain - "sys_ck": controller clock used by normal mode, - the following ones are optional: - "ref_ck": reference clock used by low power mode etc, - "mcu_ck": mcu_bus clock for register access, - "dma_ck": dma_bus clock for data transfer by DMA, - "xhci_ck": controller clock - - - phys : see usb-hcd.yaml in the current directory - -Optional properties: - - wakeup-source : enable USB remote wakeup; - - mediatek,syscon-wakeup : phandle to syscon used to access the register - of the USB wakeup glue layer between xHCI and SPM; it depends on - "wakeup-source", and has two arguments: - - the first one : register base address of the glue layer in syscon; - - the second one : hardware version of the glue layer - - 1 : used by mt8173 etc - - 2 : used by mt2712 etc - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, - bit1 for u3port1, ... etc; - - vbus-supply : reference to the VBUS regulator; - - usb3-lpm-capable : supports USB3.0 LPM - - pinctrl-names : a pinctrl state named "default" must be defined - - pinctrl-0 : pin control group - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - - imod-interval-ns: default interrupt moderation interval is 5000ns - -additionally the properties from usb-hcd.yaml (in the current directory) are -supported. - -Example: -usb30: usb@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>, - <0 0x11280700 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, - <&pericfg CLK_PERI_USB0>, - <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck"; - phys = <&phy_port0 PHY_TYPE_USB3>, - <&phy_port1 PHY_TYPE_USB2>; - vusb33-supply = <&mt6397_vusb_reg>; - vbus-supply = <&usb_p1_vbus>; - usb3-lpm-capable; - mediatek,syscon-wakeup = <&pericfg 0x400 1>; - wakeup-source; - imod-interval-ns = <10000>; -}; - -2nd: dual-role mode with xHCI driver ------------------------------------------------------------------------- - -In the case, xhci is added as subnode to mtu3. An example and the DT binding -details of mtu3 can be found in: -Documentation/devicetree/bindings/usb/mediatek,mtu3.txt - -Required properties: - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in - addition, one of: - - "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for xHCI MAC - - interrupts : interrupt used by the host controller - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain "sys_ck", and the following ones are optional: - "ref_ck", "mcu_ck" and "dma_ck", "xhci_ck" - -Optional properties: - - vbus-supply : reference to the VBUS regulator; - - usb3-lpm-capable : supports USB3.0 LPM - -Example: -usb30: usb@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>; - reg-names = "mac"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - usb3-lpm-capable; -}; |