diff options
Diffstat (limited to 'Documentation/devicetree')
262 files changed, 2283 insertions, 612 deletions
diff --git a/Documentation/devicetree/bindings/arm/actions.txt b/Documentation/devicetree/bindings/arm/actions.txt index ced764a8549e..d54f33c4e0da 100644 --- a/Documentation/devicetree/bindings/arm/actions.txt +++ b/Documentation/devicetree/bindings/arm/actions.txt @@ -21,10 +21,26 @@ Boards: Root node property compatible must contain, depending on board: + - Allo.com Sparky: "allo,sparky" - Cubietech CubieBoard6: "cubietech,cubieboard6" - LeMaker Guitar Base Board rev. B: "lemaker,guitar-bb-rev-b", "lemaker,guitar" +S700 SoC +======== + +Required root node properties: + +- compatible : must contain "actions,s700" + + +Boards: + +Root node property compatible must contain, depending on board: + + - Cubietech CubieBoard7: "cubietech,cubieboard7" + + S900 SoC ======== diff --git a/Documentation/devicetree/bindings/arm/arm-dsu-pmu.txt b/Documentation/devicetree/bindings/arm/arm-dsu-pmu.txt new file mode 100644 index 000000000000..6efabba530f1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm-dsu-pmu.txt @@ -0,0 +1,27 @@ +* ARM DynamIQ Shared Unit (DSU) Performance Monitor Unit (PMU) + +ARM DyanmIQ Shared Unit (DSU) integrates one or more CPU cores +with a shared L3 memory system, control logic and external interfaces to +form a multicore cluster. The PMU enables to gather various statistics on +the operations of the DSU. The PMU provides independent 32bit counters that +can count any of the supported events, along with a 64bit cycle counter. +The PMU is accessed via CPU system registers and has no MMIO component. + +** DSU PMU required properties: + +- compatible : should be one of : + + "arm,dsu-pmu" + +- interrupts : Exactly 1 SPI must be listed. + +- cpus : List of phandles for the CPUs connected to this DSU instance. + + +** Example: + +dsu-pmu-0 { + compatible = "arm,dsu-pmu"; + interrupts = <GIC_SPI 02 IRQ_TYPE_LEVEL_HIGH>; + cpus = <&cpu_0>, <&cpu_1>; +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 91cb8e4f2a4f..31220b54d85d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -90,38 +90,6 @@ System Timer (ST) required properties: Its subnodes can be: - watchdog: compatible should be "atmel,at91rm9200-wdt" -TC/TCLIB Timer required properties: -- compatible: Should be "atmel,<chip>-tcb". - <chip> can be "at91rm9200" or "at91sam9x5" -- reg: Should contain registers location and length -- interrupts: Should contain all interrupts for the TC block - Note that you can specify several interrupt cells if the TC - block has one interrupt per channel. -- clock-names: tuple listing input clock names. - Required elements: "t0_clk", "slow_clk" - Optional elements: "t1_clk", "t2_clk" -- clocks: phandles to input clocks. - -Examples: - -One interrupt per TC block: - tcb0: timer@fff7c000 { - compatible = "atmel,at91rm9200-tcb"; - reg = <0xfff7c000 0x100>; - interrupts = <18 4>; - clocks = <&tcb0_clk>; - clock-names = "t0_clk"; - }; - -One interrupt per TC channel in a TC block: - tcb1: timer@fffdc000 { - compatible = "atmel,at91rm9200-tcb"; - reg = <0xfffdc000 0x100>; - interrupts = <26 4 27 4 28 4>; - clocks = <&tcb1_clk>; - clock-names = "t0_clk"; - }; - RSTC Reset Controller required properties: - compatible: Should be "atmel,<chip>-rstc". <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt index ea3fb96ae465..de58f2463880 100644 --- a/Documentation/devicetree/bindings/arm/axentia.txt +++ b/Documentation/devicetree/bindings/arm/axentia.txt @@ -10,6 +10,15 @@ compatible = "axentia,linea", and following the rules from atmel-at91.txt for a sama5d31 SoC. +Nattis v2 board with Natte v2 power board +----------------------------------------- + +Required root node properties: +compatible = "axentia,nattis-2", "axentia,natte-2", "axentia,linea", + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; +and following the rules from above for the axentia,linea CPU module. + + TSE-850 v3 board ---------------- diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index 790e6b0b8306..c052caad36e8 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -17,21 +17,23 @@ Further, syscon nodes that map platform-specific registers used for general system control is required: - compatible: "brcm,bcm<chip_id>-sun-top-ctrl", "syscon" - - compatible: "brcm,bcm<chip_id>-hif-cpubiuctrl", "syscon" + - compatible: "brcm,bcm<chip_id>-cpu-biu-ctrl", + "brcm,brcmstb-cpu-biu-ctrl", + "syscon" - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon" -hif-cpubiuctrl node +cpu-biu-ctrl node ------------------- -SoCs with Broadcom Brahma15 ARM-based CPUs have a specific Bus Interface Unit -(BIU) block which controls and interfaces the CPU complex to the different -Memory Controller Ports (MCP), one per memory controller (MEMC). This BIU block -offers a feature called Write Pairing which consists in collapsing two adjacent -cache lines into a single (bursted) write transaction towards the memory -controller (MEMC) to maximize write bandwidth. +SoCs with Broadcom Brahma15 ARM-based and Brahma53 ARM64-based CPUs have a +specific Bus Interface Unit (BIU) block which controls and interfaces the CPU +complex to the different Memory Controller Ports (MCP), one per memory +controller (MEMC). This BIU block offers a feature called Write Pairing which +consists in collapsing two adjacent cache lines into a single (bursted) write +transaction towards the memory controller (MEMC) to maximize write bandwidth. Required properties: - - compatible: must be "brcm,bcm7445-hif-cpubiuctrl", "syscon" + - compatible: must be "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon" Optional properties: @@ -52,7 +54,7 @@ example: }; hif_cpubiuctrl: syscon@3e2400 { - compatible = "brcm,bcm7445-hif-cpubiuctrl", "syscon"; + compatible = "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon"; reg = <0x3e2400 0x5b4>; brcm,write-pairing; }; diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/arm/ccn.txt index 29801456c9ee..43b5a71a5a9d 100644 --- a/Documentation/devicetree/bindings/arm/ccn.txt +++ b/Documentation/devicetree/bindings/arm/ccn.txt @@ -15,7 +15,7 @@ Required properties: Example: - ccn@0x2000000000 { + ccn@2000000000 { compatible = "arm,ccn-504"; reg = <0x20 0x00000000 0 0x1000000>; interrupts = <0 181 4>; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index a0009b72e9be..f4a777039f03 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -169,6 +169,7 @@ described below. "arm,cortex-r5" "arm,cortex-r7" "brcm,brahma-b15" + "brcm,brahma-b53" "brcm,vulcan" "cavium,thunder" "cavium,thunder2" diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt index 51336e5fc761..35c3c3460d17 100644 --- a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt @@ -14,3 +14,22 @@ following property before the previous one: Example: compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3710"; + + +Power management +---------------- + +For power management (particularly DVFS and AVS), the North Bridge +Power Management component is needed: + +Required properties: +- compatible : should contain "marvell,armada-3700-nb-pm", "syscon"; +- reg : the register start and length for the North Bridge + Power Management + +Example: + +nb_pm: syscon@14000 { + compatible = "marvell,armada-3700-nb-pm", "syscon"; + reg = <0x14000 0x60>; +} diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt index 7aa3fa167668..6cc7840ff37a 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -20,4 +20,5 @@ ethsys: clock-controller@1b000000 { compatible = "mediatek,mt2701-ethsys", "syscon"; reg = <0 0x1b000000 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt index bb5727ae004a..ecb360ed0e33 100644 --- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt @@ -49,7 +49,7 @@ An interrupt consumer on an SoC using crossbar will use: interrupts = <GIC_SPI request_number interrupt_level> Example: - device_x@0x4a023000 { + device_x@4a023000 { /* Crossbar 8 used */ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; ... diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index ccaaec6014bd..6c49db7f8ad2 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -55,7 +55,7 @@ Note: child nodes can be added for auto probing from device tree. Example: adding device info in dtsi file -adc: adc@12D10000 { +adc: adc@12d10000 { compatible = "samsung,exynos-adc-v1"; reg = <0x12D10000 0x100>; interrupts = <0 106 0>; @@ -71,7 +71,7 @@ adc: adc@12D10000 { Example: adding device info in dtsi file for Exynos3250 with additional sclk -adc: adc@126C0000 { +adc: adc@126c0000 { compatible = "samsung,exynos3250-adc", "samsung,exynos-adc-v2; reg = <0x126C0000 0x100>; interrupts = <0 137 0>; @@ -87,7 +87,7 @@ adc: adc@126C0000 { Example: Adding child nodes in dts file -adc@12D10000 { +adc@12d10000 { /* NTC thermistor is a hwmon device */ ncp15wb473@0 { diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index e13459618581..469ac98ecf8f 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -72,7 +72,7 @@ Optional nodes: - compatible: only "samsung,secure-firmware" is currently supported - reg: address of non-secure SYSRAM used for communication with firmware - firmware@203F000 { + firmware@203f000 { compatible = "samsung,secure-firmware"; reg = <0x0203F000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 020d758fc0c5..5c3af7ef0761 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -104,12 +104,16 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7796" - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7795" + - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S) + compatible = "renesas,salvator-xs", "renesas,r8a7796" - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" - SK-RZG1E (YR8A77450S000BE) compatible = "renesas,sk-rzg1e", "renesas,r8a7745" - SK-RZG1M (YR8A77430S000BE) compatible = "renesas,sk-rzg1m", "renesas,r8a7743" + - V3MSK + compatible = "renesas,v3msk", "renesas,r8a77970" - Wheat compatible = "renesas,wheat", "renesas,r8a7792" diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt new file mode 100644 index 000000000000..05762b08a7bb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32.txt @@ -0,0 +1,9 @@ +STMicroelectronics STM32 Platforms Device Tree Bindings + +Each device tree must specify which STM32 SoC it uses, +using one of the following compatible strings: + + st,stm32f429 + st,stm32f469 + st,stm32f746 + st,stm32h743 diff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt index 33797acad846..f1cedc00dcab 100644 --- a/Documentation/devicetree/bindings/arm/technologic.txt +++ b/Documentation/devicetree/bindings/arm/technologic.txt @@ -1,6 +1,11 @@ Technologic Systems Platforms Device Tree Bindings -------------------------------------------------- +TS-4600 is a System-on-Module based on the Freescale i.MX28 System-on-Chip. +It can be mounted on a carrier board providing additional peripheral connectors. +Required root node properties: + - compatible = "technologic,imx28-ts4600", "fsl,imx28" + TS-4800 board Required root node properties: - compatible = "technologic,imx51-ts4800", "fsl,imx51"; @@ -10,3 +15,9 @@ It can be mounted on a carrier board providing additional peripheral connectors. Required root node properties: - compatible = "technologic,imx6dl-ts4900", "fsl,imx6dl" - compatible = "technologic,imx6q-ts4900", "fsl,imx6q" + +TS-7970 is a System-on-Module based on the Freescale i.MX6 System-on-Chip. +It can be mounted on a carrier board providing additional peripheral connectors. +Required root node properties: + - compatible = "technologic,imx6dl-ts7970", "fsl,imx6dl" + - compatible = "technologic,imx6q-ts7970", "fsl,imx6q" diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt index 866d93421eba..f9632bacbd04 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt @@ -8,7 +8,7 @@ Required properties: - interrupts : Should contain MC General interrupt. Example: - memory-controller@0x7000f000 { + memory-controller@7000f000 { compatible = "nvidia,tegra20-mc"; reg = <0x7000f000 0x024 0x7000f03c 0x3c4>; diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt index fb1790e39398..2957a9ae291f 100644 --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -19,6 +19,7 @@ Required standard properties: - compatible shall be one of the following generic types: + "ti,sysc" "ti,sysc-omap2" "ti,sysc-omap4" "ti,sysc-omap4-simple" @@ -26,6 +27,8 @@ Required standard properties: or one of the following derivative types for hardware needing special workarounds: + "ti,sysc-omap2-timer" + "ti,sysc-omap4-timer" "ti,sysc-omap3430-sr" "ti,sysc-omap3630-sr" "ti,sysc-omap4-sr" @@ -49,6 +52,26 @@ Required standard properties: Optional properties: +- ti,sysc-mask shall contain mask of supported register bits for the + SYSCONFIG register as documented in the Technical Reference + Manual (TRM) for the interconnect target module + +- ti,sysc-midle list of master idle modes supported by the interconnect + target module as documented in the TRM for SYSCONFIG + register MIDLEMODE bits + +- ti,sysc-sidle list of slave idle modes supported by the interconnect + target module as documented in the TRM for SYSCONFIG + register SIDLEMODE bits + +- ti,sysc-delay-us delay needed after OCP softreset before accssing + SYSCONFIG register again + +- ti,syss-mask optional mask of reset done status bits as described in the + TRM for SYSSTATUS registers, typically 1 with some devices + having separate reset done bits for children like OHCI and + EHCI + - clocks clock specifier for each name in the clock-names as specified in the binding documentation for ti-clkctrl, typically available for all interconnect targets on TI SoCs @@ -61,6 +84,9 @@ Optional properties: - ti,hwmods optional TI interconnect module name to use legacy hwmod platform data +- ti,no-reset-on-init interconnect target module should not be reset at init + +- ti,no-idle-on-init interconnect target module should not be idled at init Example: Single instance of MUSB controller on omap4 using interconnect ranges using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): @@ -74,6 +100,17 @@ using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): reg-names = "rev", "sysc", "syss"; clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>; clock-names = "fck"; + ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,syss-mask = <1>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x2b000 0x1000>; diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt index e3b13ea7d2ae..45e79172a646 100644 --- a/Documentation/devicetree/bindings/chosen.txt +++ b/Documentation/devicetree/bindings/chosen.txt @@ -120,3 +120,18 @@ e.g. While this property does not represent a real hardware, the address and the size are expressed in #address-cells and #size-cells, respectively, of the root node. + +linux,initrd-start and linux,initrd-end +--------------------------------------- + +These properties hold the physical start and end address of an initrd that's +loaded by the bootloader. Note that linux,initrd-start is inclusive, but +linux,initrd-end is exclusive. +e.g. + +/ { + chosen { + linux,initrd-start = <0x82000000>; + linux,initrd-end = <0x82800000>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index 924040769186..e2b377ed6f91 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -5,8 +5,11 @@ controllers within the SoC. Required Properties: -- compatible: should be "amlogic,gxbb-clkc" for GXBB SoC, - or "amlogic,gxl-clkc" for GXL and GXM SoC. +- compatible: should be: + "amlogic,gxbb-clkc" for GXBB SoC, + "amlogic,gxl-clkc" for GXL and GXM SoC, + "amlogic,axg-clkc" for AXG SoC. + - reg: physical base address of the clock controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt index fb40da303d25..aca94fe9416f 100644 --- a/Documentation/devicetree/bindings/clock/axi-clkgen.txt +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -17,7 +17,7 @@ Optional properties: - clock-output-names : From common clock binding. Example: - clock@0xff000000 { + clock@ff000000 { compatible = "adi,axi-clkgen"; #clock-cells = <0>; reg = <0xff000000 0x1000>; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt index 7a837d2182ac..4acfc8f641b6 100644 --- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt @@ -23,7 +23,7 @@ Example: clocks = <&clk_osc>; }; - aux: aux@0x7e215004 { + aux: aux@7e215004 { compatible = "brcm,bcm2835-aux"; #clock-cells = <1>; reg = <0x7e215000 0x8>; diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt index f1738b88c225..7441ed519f02 100644 --- a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -32,7 +32,7 @@ Example 1: Examples of clock controller nodes are listed below. #clock-cells = <1>; }; - cmu_dmc: clock-controller@105C0000 { + cmu_dmc: clock-controller@105c0000 { compatible = "samsung,exynos3250-cmu-dmc"; reg = <0x105C0000 0x2000>; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index bc61c952cb0b..17bb11365354 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -24,7 +24,7 @@ tree sources. Example 1: An example of a clock controller node is listed below. - clock: clock-controller@0x10030000 { + clock: clock-controller@10030000 { compatible = "samsung,exynos4210-clock"; reg = <0x10030000 0x20000>; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt index 536eacd1063f..aff266a12eeb 100644 --- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -22,7 +22,7 @@ tree sources. Example 1: An example of a clock controller node is listed below. - clock: clock-controller@0x10010000 { + clock: clock-controller@10010000 { compatible = "samsung,exynos5250-clock"; reg = <0x10010000 0x30000>; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt index 5496b2fac483..c79d31f7f66e 100644 --- a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt @@ -180,7 +180,7 @@ Example 2: UART controller node that consumes the clock generated by the peri clock controller. Refer to the standard clock bindings for information about 'clocks' and 'clock-names' property. - serial@12C00000 { + serial@12c00000 { compatible = "samsung,exynos4210-uart"; reg = <0x12C00000 0x100>; interrupts = <0 146 0>; diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt index 4527de3ea205..217beb27c30e 100644 --- a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -30,7 +30,7 @@ Example 1: An example of a clock controller node is listed below. #clock-cells = <0>; }; - clock: clock-controller@0x10010000 { + clock: clock-controller@10010000 { compatible = "samsung,exynos5410-clock"; reg = <0x10010000 0x30000>; #clock-cells = <1>; @@ -41,7 +41,7 @@ Example 2: UART controller node that consumes the clock generated by the clock controller. Refer to the standard clock bindings for information about 'clocks' and 'clock-names' property. - serial@12C20000 { + serial@12c20000 { compatible = "samsung,exynos4210-uart"; reg = <0x12C00000 0x100>; interrupts = <0 51 0>; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index d54f42cf0440..717a7b1531c7 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -23,7 +23,7 @@ tree sources. Example 1: An example of a clock controller node is listed below. - clock: clock-controller@0x10010000 { + clock: clock-controller@10010000 { compatible = "samsung,exynos5420-clock"; reg = <0x10010000 0x30000>; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt index c473dd38dd55..50d5897c9849 100644 --- a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -472,7 +472,7 @@ Example 2: Examples of clock controller nodes are listed below. Example 3: UART controller node that consumes the clock generated by the clock controller. - serial_0: serial@14C10000 { + serial_0: serial@14c10000 { compatible = "samsung,exynos5433-uart"; reg = <0x14C10000 0x100>; interrupts = <0 421 0>; diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt index 5f7005f73058..c7d227c31e95 100644 --- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt @@ -21,7 +21,7 @@ tree sources. Example: An example of a clock controller node is listed below. - clock: clock-controller@0x10010000 { + clock: clock-controller@10010000 { compatible = "samsung,exynos5440-clock"; reg = <0x160000 0x10000>; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt index 0035a7ecaf20..946da7cee54f 100644 --- a/Documentation/devicetree/bindings/clock/hi3660-clock.txt +++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt @@ -13,12 +13,18 @@ Required Properties: - "hisilicon,hi3660-pmuctrl" - "hisilicon,hi3660-sctrl" - "hisilicon,hi3660-iomcu" + - "hisilicon,hi3660-stub-clk" - reg: physical base address of the controller and length of memory mapped region. - #clock-cells: should be 1. +Optional Properties: + +- mboxes: Phandle to the mailbox for sending message to MCU. + (See: ../mailbox/hisilicon,hi3660-mailbox.txt for more info) + Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. diff --git a/Documentation/devicetree/bindings/clock/qcom,a53pll.txt b/Documentation/devicetree/bindings/clock/qcom,a53pll.txt new file mode 100644 index 000000000000..e3fa8118eaee --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,a53pll.txt @@ -0,0 +1,22 @@ +Qualcomm MSM8916 A53 PLL Binding +-------------------------------- +The A53 PLL on MSM8916 platforms is the main CPU PLL used used for frequencies +above 1GHz. + +Required properties : +- compatible : Shall contain only one of the following: + + "qcom,msm8916-a53pll" + +- reg : shall contain base register location and length + +- #clock-cells : must be set to <0> + +Example: + + a53pll: clock@b016000 { + compatible = "qcom,msm8916-a53pll"; + reg = <0xb016000 0x40>; + #clock-cells = <0>; + }; + diff --git a/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt b/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt new file mode 100644 index 000000000000..7474aba36607 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt @@ -0,0 +1,59 @@ +Qualcomm Technologies, Inc. SPMI PMIC clock divider (clkdiv) + +clkdiv configures the clock frequency of a set of outputs on the PMIC. +These clocks are typically wired through alternate functions on +gpio pins. + +======================= +Properties +======================= + +- compatible + Usage: required + Value type: <string> + Definition: must be "qcom,spmi-clkdiv". + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: base address of CLKDIV peripherals. + +- qcom,num-clkdivs + Usage: required + Value type: <u32> + Definition: number of CLKDIV peripherals. + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the xo clock. + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "xo". + +- #clock-cells: + Usage: required + Value type: <u32> + Definition: shall contain 1. + +======= +Example +======= + +pm8998_clk_divs: clock-controller@5b00 { + compatible = "qcom,spmi-clkdiv"; + reg = <0x5b00>; + #clock-cells = <1>; + qcom,num-clkdivs = <3>; + clocks = <&xo_board>; + clock-names = "xo"; + + assigned-clocks = <&pm8998_clk_divs 1>, + <&pm8998_clk_divs 2>, + <&pm8998_clk_divs 3>; + assigned-clock-rates = <9600000>, + <9600000>, + <9600000>; +}; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 6498e1fdbb33..97f46adac85f 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -78,6 +78,7 @@ second cell is the clock index for the specified type. 2 hwaccel index (n in CLKCGnHWACSR) 3 fman 0 for fm1, 1 for fm2 4 platform pll 0=pll, 1=pll/2, 2=pll/3, 3=pll/4 + 4=pll/5, 5=pll/6, 6=pll/7, 7=pll/8 5 coreclk must be 0 3. Example diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index a6c4ef343b44..f00191cad8cd 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -49,6 +49,7 @@ Optional child node properties: - silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth divider. - silabs,pll-master: boolean, multisynth can change pll frequency. +- silabs,pll-reset: boolean, clock output can reset its pll. - silabs,disable-state : clock output disable state, shall be 0 = clock output is driven LOW when disabled 1 = clock output is driven HIGH when disabled diff --git a/Documentation/devicetree/bindings/clock/sprd.txt b/Documentation/devicetree/bindings/clock/sprd.txt new file mode 100644 index 000000000000..e9d179e882d9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sprd.txt @@ -0,0 +1,63 @@ +Spreadtrum Clock Binding +------------------------ + +Required properties: +- compatible: should contain the following compatible strings: + - "sprd,sc9860-pmu-gate" + - "sprd,sc9860-pll" + - "sprd,sc9860-ap-clk" + - "sprd,sc9860-aon-prediv" + - "sprd,sc9860-apahb-gate" + - "sprd,sc9860-aon-gate" + - "sprd,sc9860-aonsecure-clk" + - "sprd,sc9860-agcp-gate" + - "sprd,sc9860-gpu-clk" + - "sprd,sc9860-vsp-clk" + - "sprd,sc9860-vsp-gate" + - "sprd,sc9860-cam-clk" + - "sprd,sc9860-cam-gate" + - "sprd,sc9860-disp-clk" + - "sprd,sc9860-disp-gate" + - "sprd,sc9860-apapb-gate" + +- #clock-cells: must be 1 + +- clocks : Should be the input parent clock(s) phandle for the clock, this + property here just simply shows which clock group the clocks' + parents are in, since each clk node would represent many clocks + which are defined in the driver. The detailed dependency + relationship (i.e. how many parents and which are the parents) + are implemented in driver code. + +Optional properties: + +- reg: Contain the registers base address and length. It must be configured + only if no 'sprd,syscon' under the node. + +- sprd,syscon: phandle to the syscon which is in the same address area with + the clock, and so we can get regmap for the clocks from the + syscon device. + +Example: + + pmu_gate: pmu-gate { + compatible = "sprd,sc9860-pmu-gate"; + sprd,syscon = <&pmu_regs>; + clocks = <&ext_26m>; + #clock-cells = <1>; + }; + + pll: pll { + compatible = "sprd,sc9860-pll"; + sprd,syscon = <&ana_regs>; + clocks = <&pmu_gate 0>; + #clock-cells = <1>; + }; + + ap_clk: clock-controller@20000000 { + compatible = "sprd,sc9860-ap-clk"; + reg = <0 0x20000000 0 0x400>; + clocks = <&ext_26m>, <&pll 0>, + <&pmu_gate 0>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/sun8i-de2.txt b/Documentation/devicetree/bindings/clock/sun8i-de2.txt index 631d27cd89d6..f2fa87c4765c 100644 --- a/Documentation/devicetree/bindings/clock/sun8i-de2.txt +++ b/Documentation/devicetree/bindings/clock/sun8i-de2.txt @@ -4,13 +4,14 @@ Allwinner Display Engine 2.0 Clock Control Binding Required properties : - compatible: must contain one of the following compatibles: - "allwinner,sun8i-a83t-de2-clk" + - "allwinner,sun8i-h3-de2-clk" - "allwinner,sun8i-v3s-de2-clk" - "allwinner,sun50i-h5-de2-clk" - reg: Must contain the registers base address and length - clocks: phandle to the clocks feeding the display engine subsystem. Three are needed: - - "mod": the display engine module clock + - "mod": the display engine module clock (on A83T it's the DE PLL) - "bus": the bus clock for the whole display engine subsystem - clock-names: Must contain the clock names described just above - resets: phandle to the reset control for the display engine subsystem. @@ -19,7 +20,7 @@ Required properties : Example: de2_clocks: clock@1000000 { - compatible = "allwinner,sun8i-a83t-de2-clk"; + compatible = "allwinner,sun8i-h3-de2-clk"; reg = <0x01000000 0x100000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt index 3e6a81e99804..c35cb6c4af4d 100644 --- a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt +++ b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt @@ -14,7 +14,7 @@ Required properties: Example: -pllctrl: pll-controller@0x02310000 { +pllctrl: pll-controller@02310000 { compatible = "ti,keystone-pllctrl", "syscon"; reg = <0x02310000 0x200>; }; diff --git a/Documentation/devicetree/bindings/clock/zx296702-clk.txt b/Documentation/devicetree/bindings/clock/zx296702-clk.txt index e85ecb510d56..5c91c9e4f1be 100644 --- a/Documentation/devicetree/bindings/clock/zx296702-clk.txt +++ b/Documentation/devicetree/bindings/clock/zx296702-clk.txt @@ -20,13 +20,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h for the full list of zx296702 clock IDs. -topclk: topcrm@0x09800000 { +topclk: topcrm@09800000 { compatible = "zte,zx296702-topcrm-clk"; reg = <0x09800000 0x1000>; #clock-cells = <1>; }; -uart0: serial@0x09405000 { +uart0: serial@09405000 { compatible = "zte,zx296702-uart"; reg = <0x09405000 0x1000>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/crypto/arm-cryptocell.txt b/Documentation/devicetree/bindings/crypto/arm-cryptocell.txt new file mode 100644 index 000000000000..cec8d5d74e26 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/arm-cryptocell.txt @@ -0,0 +1,22 @@ +Arm TrustZone CryptoCell cryptographic engine + +Required properties: +- compatible: Should be "arm,cryptocell-712-ree". +- reg: Base physical address of the engine and length of memory mapped region. +- interrupts: Interrupt number for the device. + +Optional properties: +- interrupt-parent: The phandle for the interrupt controller that services + interrupts for this device. +- clocks: Reference to the crypto engine clock. +- dma-coherent: Present if dma operations are coherent. + +Examples: + + arm_cc712: crypto@80000000 { + compatible = "arm,cryptocell-712-ree"; + interrupt-parent = <&intc>; + interrupts = < 0 30 4 >; + reg = < 0x80000000 0x10000 >; + + }; diff --git a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt index 7de1a9674c70..6b458bb2440d 100644 --- a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt @@ -75,7 +75,7 @@ Required properties: - clock-frequency: must be present in the i2c controller node. Example: -atecc508a@C0 { +atecc508a@c0 { compatible = "atmel,atecc508a"; reg = <0xC0>; }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index 7aef0eae58d4..76aec8a3724d 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -456,7 +456,7 @@ System ON/OFF key driver Definition: this is phandle to the register map node. EXAMPLE: - snvs-pwrkey@0x020cc000 { + snvs-pwrkey@020cc000 { compatible = "fsl,sec-v4.0-pwrkey"; regmap = <&snvs>; interrupts = <0 4 0x4> @@ -545,7 +545,7 @@ FULL EXAMPLE interrupts = <93 2>; }; - snvs-pwrkey@0x020cc000 { + snvs-pwrkey@020cc000 { compatible = "fsl,sec-v4.0-pwrkey"; regmap = <&sec_mon>; interrupts = <0 4 0x4>; diff --git a/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt b/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt index 4ca8dd4d7e66..a13fbdb4bd88 100644 --- a/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt +++ b/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt @@ -2,7 +2,9 @@ Exynos Pseudo Random Number Generator Required properties: -- compatible : Should be "samsung,exynos4-rng". +- compatible : One of: + - "samsung,exynos4-rng" for Exynos4210 and Exynos4412 + - "samsung,exynos5250-prng" for Exynos5250+ - reg : Specifies base physical address and size of the registers map. - clocks : Phandle to clock-controller plus clock-specifier pair. - clock-names : "secss" as a clock name. diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.txt b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.txt new file mode 100644 index 000000000000..970487fa40b8 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.txt @@ -0,0 +1,19 @@ +* STMicroelectronics STM32 CRYP + +Required properties: +- compatible: Should be "st,stm32f756-cryp". +- reg: The address and length of the peripheral registers space +- clocks: The input clock of the CRYP instance +- interrupts: The CRYP interrupt + +Optional properties: +- resets: The input reset of the CRYP instance + +Example: +crypto@50060000 { + compatible = "st,stm32f756-cryp"; + reg = <0x50060000 0x400>; + interrupts = <79>; + clocks = <&rcc 0 STM32F7_AHB2_CLOCK(CRYP)>; + resets = <&rcc STM32F7_AHB2_RESET(CRYP)>; +}; diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt index fd459f00aa5a..aeaebd425d1f 100644 --- a/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt @@ -20,7 +20,7 @@ Optional properties: Example : NoC Probe nodes in Device Tree are listed below. - nocp_mem0_0: nocp@10CA1000 { + nocp_mem0_0: nocp@10ca1000 { compatible = "samsung,exynos5420-nocp"; reg = <0x10CA1000 0x200>; }; diff --git a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt index 001dd63979a9..148191b0fc15 100644 --- a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt +++ b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt @@ -9,7 +9,7 @@ Required properties: - clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon"; Example: - dfi: dfi@0xff630000 { + dfi: dfi@ff630000 { compatible = "rockchip,rk3399-dfi"; reg = <0x00 0xff630000 0x00 0x4000>; rockchip,pmu = <&pmugrf>; diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt index 7f040edc16fe..bf4a18047309 100644 --- a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt @@ -48,6 +48,10 @@ Required properties: Documentation/devicetree/bindings/reset/reset.txt, the reset-names should be "hdmitx_apb", "hdmitx", "hdmitx_phy" +Optional properties: +- hdmi-supply: Optional phandle to an external 5V regulator to power the HDMI + logic, as described in the file ../regulator/regulator.txt + Required nodes: The connections to the HDMI ports are modeled using the OF graph diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt index 00f74bad1e95..057b81335775 100644 --- a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt @@ -64,6 +64,10 @@ Required properties: - reg-names: should contain the names of the previous memory regions - interrupts: should contain the VENC Vsync interrupt number +Optional properties: +- power-domains: Optional phandle to associated power domain as described in + the file ../power/power_domain.txt + Required nodes: The connections to the VPU output video ports are modeled using the OF graph diff --git a/Documentation/devicetree/bindings/display/atmel,lcdc.txt b/Documentation/devicetree/bindings/display/atmel,lcdc.txt index 1a21202778ee..acb5a0132127 100644 --- a/Documentation/devicetree/bindings/display/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/display/atmel,lcdc.txt @@ -27,7 +27,7 @@ Optional properties: Example: - fb0: fb@0x00500000 { + fb0: fb@00500000 { compatible = "atmel,at91sam9g45-lcdc"; reg = <0x00500000 0x1000>; interrupts = <23 3 0>; @@ -41,7 +41,7 @@ Example: Example for fixed framebuffer memory: - fb0: fb@0x00500000 { + fb0: fb@00500000 { compatible = "atmel,at91sam9263-lcdc"; reg = <0x00700000 0x1000 0x70000000 0x200000>; [...] diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index ca5204b3bc21..2fff8b406f4c 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -54,7 +54,7 @@ Video interfaces: Example: - dsi@11C80000 { + dsi@11c80000 { compatible = "samsung,exynos4210-mipi-dsi"; reg = <0x11C80000 0x10000>; interrupts = <0 79 0>; diff --git a/Documentation/devicetree/bindings/display/ilitek,ili9225.txt b/Documentation/devicetree/bindings/display/ilitek,ili9225.txt new file mode 100644 index 000000000000..a59feb52015b --- /dev/null +++ b/Documentation/devicetree/bindings/display/ilitek,ili9225.txt @@ -0,0 +1,25 @@ +Ilitek ILI9225 display panels + +This binding is for display panels using an Ilitek ILI9225 controller in SPI +mode. + +Required properties: +- compatible: "vot,v220hf01a-t", "ilitek,ili9225" +- rs-gpios: Register select signal +- reset-gpios: Reset pin + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in ../spi/spi-bus.txt must be specified. + +Optional properties: +- rotation: panel rotation in degrees counter clockwise (0,90,180,270) + +Example: + display@0{ + compatible = "vot,v220hf01a-t", "ilitek,ili9225"; + reg = <0>; + spi-max-frequency = <12000000>; + rs-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + rotation = <270>; + }; diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt new file mode 100644 index 000000000000..3d5ce6ad6ec7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt @@ -0,0 +1,49 @@ +Ilitek ILI9322 TFT panel driver with SPI control bus + +This is a driver for 320x240 TFT panels, accepting a variety of input +streams that get adapted and scaled to the panel. The panel output has +960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and +VCOMH outputs. + +Required properties: + - compatible: "dlink,dir-685-panel", "ilitek,ili9322" + (full system-specific compatible is always required to look up configuration) + - reg: address of the panel on the SPI bus + +Optional properties: + - vcc-supply: core voltage supply, see regulator/regulator.txt + - iovcc-supply: voltage supply for the interface input/output signals, + see regulator/regulator.txt + - vci-supply: voltage supply for analog parts, see regulator/regulator.txt + - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt + + The following optional properties only apply to RGB and YUV input modes and + can be omitted for BT.656 input modes: + + - pixelclk-active: see display/panel/display-timing.txt + - de-active: see display/panel/display-timing.txt + - hsync-active: see display/panel/display-timing.txt + - vsync-active: see display/panel/display-timing.txt + +The panel must obey the rules for a SPI slave device as specified in +spi/spi-bus.txt + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in +media/video-interfaces.txt. This node should describe panel's video bus. + +Example: + +panel: display@0 { + compatible = "dlink,dir-685-panel", "ilitek,ili9322"; + reg = <0>; + vcc-supply = <&vdisp>; + iovcc-supply = <&vdisp>; + vci-supply = <&vdisp>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa070mc01.txt b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa070mc01.txt new file mode 100644 index 000000000000..7d8f6eeef6d9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa070mc01.txt @@ -0,0 +1,7 @@ +Mitsubishi "AA070MC01 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "mitsubishi,aa070mc01-ca1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt index ec52c472c845..557fa765adcb 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-common.txt @@ -78,6 +78,16 @@ used for panels that implement compatible control signals. while active. Active high reset signals can be supported by inverting the GPIO specifier polarity flag. +Power +----- + +- power-supply: display panels require power to be supplied. While several + panels need more than one power supply with panel-specific constraints + governing the order and timings of the power supplies, in many cases a single + power supply is sufficient, either because the panel has a single power rail, + or because all its power rails can be driven by the same supply. In that case + the power-supply property specifies the supply powering the panel as a phandle + to a regulator. Backlight --------- diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt index b938269f841e..250850a2150b 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt @@ -32,6 +32,7 @@ Optional properties: - label: See panel-common.txt. - gpios: See panel-common.txt. - backlight: See panel-common.txt. +- power-supply: See panel-common.txt. - data-mirror: If set, reverse the bit order described in the data mappings below on all data lanes, transmitting bits for slots 6 to 0 instead of 0 to 6. diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt new file mode 100644 index 000000000000..d06644b555bd --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt @@ -0,0 +1,41 @@ +Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel +========================================================== + +The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel. + +These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt +with the following device-specific properties. + +Required properties: + +- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order. + +Example +------- + +panel { + compatible = "sgd,gktw70sdae4se", "panel-lvds"; + + width-mm = <153>; + height-mm = <86>; + + data-mapping = "jeida-18"; + + panel-timing { + clock-frequency = <32000000>; + hactive = <800>; + vactive = <480>; + hback-porch = <39>; + hfront-porch = <39>; + vback-porch = <29>; + vfront-porch = <13>; + hsync-len = <47>; + vsync-len = <2>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt index 1341bbf4aa3d..16d8ff088b7d 100644 --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt @@ -1,7 +1,7 @@ Simple display panel Required properties: -- power-supply: regulator to provide the supply voltage +- power-supply: See panel-common.txt Optional properties: - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing diff --git a/Documentation/devicetree/bindings/display/panel/tianma,tm070rvhg71.txt b/Documentation/devicetree/bindings/display/panel/tianma,tm070rvhg71.txt new file mode 100644 index 000000000000..b25261e63a6d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tianma,tm070rvhg71.txt @@ -0,0 +1,29 @@ +Tianma Micro-electronics TM070RVHG71 7.0" WXGA TFT LCD panel + +Required properties: +- compatible: should be "tianma,tm070rvhg71" +- power-supply: single regulator to provide the supply voltage +- backlight: phandle of the backlight device attached to the panel + +Required nodes: +- port: LVDS port mapping to connect this display + +This panel needs single power supply voltage. Its backlight is conntrolled +via PWM signal. + +Example: +-------- + +Example device-tree definition when connected to iMX6Q based board + + panel: panel-lvds0 { + compatible = "tianma,tm070rvhg71"; + backlight = <&backlight_lvds>; + power-supply = <®_lvds>; + + port { + panel_in_lvds0: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt index 4c0caaf246c9..89826116628c 100644 --- a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt +++ b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt @@ -1,7 +1,7 @@ Toshiba 8.9" WXGA (1280x768) TFT LCD panel Required properties: -- compatible: should be "toshiba,lt089ac29000.txt" +- compatible: should be "toshiba,lt089ac29000" - power-supply: as specified in the base binding This binding is compatible with the simple-panel binding, which is specified diff --git a/Documentation/devicetree/bindings/display/panel/toppoly,td028ttec1.txt b/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt index 7175dc3740ac..ed34253d9fb1 100644 --- a/Documentation/devicetree/bindings/display/panel/toppoly,td028ttec1.txt +++ b/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt @@ -2,7 +2,7 @@ Toppoly TD028TTEC1 Panel ======================== Required properties: -- compatible: "toppoly,td028ttec1" +- compatible: "tpo,td028ttec1" Optional properties: - label: a symbolic name for the panel @@ -14,7 +14,7 @@ Example ------- lcd-panel: td028ttec1@0 { - compatible = "toppoly,td028ttec1"; + compatible = "tpo,td028ttec1"; reg = <0>; spi-max-frequency = <100000>; spi-cpol; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index 4bbd1e9bf3be..cd48aba3bc8c 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -3,6 +3,8 @@ Required Properties: - compatible: must be one of the following. + - "renesas,du-r8a7743" for R8A7743 (RZ/G1M) compatible DU + - "renesas,du-r8a7745" for R8A7745 (RZ/G1E) compatible DU - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU @@ -27,10 +29,10 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[0123456] use one functional clock per channel and one clock per - LVDS encoder (if available). The functional clocks must be named "du.x" - with "x" being the channel numerical index. The LVDS clocks must be - named "lvds.x" with "x" being the LVDS encoder numerical index. + - All other DU instances use one functional clock per channel and one + clock per LVDS encoder (if available). The functional clocks must be + named "du.x" with "x" being the channel numerical index. The LVDS clocks + must be named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. When supplied they must be named "dclkin.x" with "x" being the input @@ -49,16 +51,18 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port 0 Port1 Port2 Port3 + Port0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7779 (H1) DPAD 0 DPAD 1 - - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - - R8A7791 (M2-W) DPAD LVDS 0 - - - R8A7792 (V2H) DPAD 0 DPAD 1 - - - R8A7793 (M2-N) DPAD LVDS 0 - - - R8A7794 (E2) DPAD 0 DPAD 1 - - - R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS - R8A7796 (M3-W) DPAD HDMI LVDS - + R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - + R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - + R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - + R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - + R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - + R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - + R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - + R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - + R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 + R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - Example: R8A7795 (R-Car H3) ES2.0 DU diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index 5d835d9c1ba8..eeda3597011e 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -7,6 +7,7 @@ buffer to an external LCD interface. Required properties: - compatible: value should be one of the following "rockchip,rk3036-vop"; + "rockchip,rk3126-vop"; "rockchip,rk3288-vop"; "rockchip,rk3368-vop"; "rockchip,rk3366-vop"; diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt index a9168ae6946c..d693b8dc9a62 100644 --- a/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt +++ b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt @@ -15,6 +15,10 @@ Required properties: "de_be1-lcd1" "de_be0-lcd0-hdmi" "de_be1-lcd1-hdmi" + "mixer0-lcd0" + "mixer0-lcd0-hdmi" + "mixer1-lcd1-hdmi" + "mixer1-lcd1-tve" Example: diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt new file mode 100644 index 000000000000..f0a5090a3326 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt @@ -0,0 +1,35 @@ +Sitronix ST7735R display panels + +This binding is for display panels using a Sitronix ST7735R controller in SPI +mode. + +Required properties: +- compatible: "jianda,jd-t18003-t01", "sitronix,st7735r" +- dc-gpios: Display data/command selection (D/CX) +- reset-gpios: Reset signal (RSTX) + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in ../spi/spi-bus.txt must be specified. + +Optional properties: +- rotation: panel rotation in degrees counter clockwise (0,90,180,270) +- backlight: phandle of the backlight device attached to the panel + +Example: + + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; + } + + ... + + display@0{ + compatible = "jianda,jd-t18003-t01", "sitronix,st7735r"; + reg = <0>; + spi-max-frequency = <32000000>; + dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>; + rotation = <270>; + backlight = &backlight; + }; diff --git a/Documentation/devicetree/bindings/display/st,stih4xx.txt b/Documentation/devicetree/bindings/display/st,stih4xx.txt index a352ed30cd70..6778b3e7ad5b 100644 --- a/Documentation/devicetree/bindings/display/st,stih4xx.txt +++ b/Documentation/devicetree/bindings/display/st,stih4xx.txt @@ -119,7 +119,7 @@ Example: / { ... - vtg_main_slave: sti-vtg-main-slave@fe85A800 { + vtg_main_slave: sti-vtg-main-slave@fe85a800 { compatible = "st,vtg"; reg = <0xfe85A800 0x300>; interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt index 74b5ac7b26d6..029252253ad4 100644 --- a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt +++ b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt @@ -10,7 +10,11 @@ - "lcd" for the clock feeding the output pixel clock & IP clock. - resets: reset to be used by the device (defined by use of RCC macro). Required nodes: - - Video port for RGB output. + - Video port for DPI RGB output: ltdc has one video port with up to 2 + endpoints: + - for external dpi rgb panel or bridge, using gpios. + - for internal dpi input of the MIPI DSI host controller. + Note: These 2 endpoints cannot be activated simultaneously. * STMicroelectronics STM32 DSI controller specific extensions to Synopsys DesignWare MIPI DSI host controller diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index 50cc72ee1168..cd626ee1147a 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -93,6 +93,7 @@ Required properties: * allwinner,sun6i-a31s-tcon * allwinner,sun7i-a20-tcon * allwinner,sun8i-a33-tcon + * allwinner,sun8i-a83t-tcon-lcd * allwinner,sun8i-v3s-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP @@ -121,6 +122,14 @@ Required properties: On SoCs other than the A33 and V3s, there is one more clock required: - 'tcon-ch1': The clock driving the TCON channel 1 +On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you +need one more reset line: + - 'lvds': The reset line driving the LVDS logic + +And on the A23, A31, A31s and A33, you need one more clock line: + - 'lvds-alt': An alternative clock source, separate from the TCON channel 0 + clock, that can be used to drive the LVDS clock + DRC --- @@ -216,6 +225,7 @@ supported. Required properties: - compatible: value must be one of: + * allwinner,sun8i-a83t-de2-mixer-0 * allwinner,sun8i-v3s-de2-mixer - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the mixer @@ -245,6 +255,7 @@ Required properties: * allwinner,sun6i-a31s-display-engine * allwinner,sun7i-a20-display-engine * allwinner,sun8i-a33-display-engine + * allwinner,sun8i-a83t-display-engine * allwinner,sun8i-v3s-display-engine - allwinner,pipelines: list of phandle to the display engine diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 844e0103fb0d..593be44a53c9 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -206,21 +206,33 @@ of the following host1x client modules: - "nvidia,tegra132-sor": for Tegra132 - "nvidia,tegra210-sor": for Tegra210 - "nvidia,tegra210-sor1": for Tegra210 + - "nvidia,tegra186-sor": for Tegra186 + - "nvidia,tegra186-sor1": for Tegra186 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - sor: clock input for the SOR hardware - - source: source clock for the SOR clock + - out: SOR output clock - parent: input for the pixel clock - dp: reference clock for the SOR clock - safe: safe reference for the SOR clock during power up + + For Tegra186 and later: + - pad: SOR pad output clock (on Tegra186 and later) + + Obsolete: + - source: source clock for the SOR clock (obsolete, use "out" instead) + - resets: Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. - reset-names: Must include the following entries: - sor + Required properties on Tegra186 and later: + - nvidia,interface: index of the SOR interface + Optional properties: - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection diff --git a/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt index c30f9ec189ed..91279f1060fe 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt +++ b/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt @@ -47,6 +47,11 @@ Required properties: - clocks: handle to fclk - clock-names: "fck" +Optional properties: +- max-memory-bandwidth: Input memory (from main memory to dispc) bandwidth limit + in bytes per second + + HDMI ---- diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt index afcd5a86c6a4..ee867c4d1152 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt +++ b/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt @@ -28,6 +28,10 @@ Required properties: - ti,hwmods: "dss_dispc" - interrupts: the DISPC interrupt +Optional properties: +- max-memory-bandwidth: Input memory (from main memory to dispc) bandwidth limit + in bytes per second + RFBI ---- diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt index dc66e1447c31..cd02516a40b6 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt +++ b/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt @@ -37,6 +37,10 @@ Required properties: - clocks: handle to fclk - clock-names: "fck" +Optional properties: +- max-memory-bandwidth: Input memory (from main memory to dispc) bandwidth limit + in bytes per second + RFBI ---- diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt index bc624db8888d..0f85f6b3a5a8 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt +++ b/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt @@ -36,6 +36,10 @@ Required properties: - clocks: handle to fclk - clock-names: "fck" +Optional properties: +- max-memory-bandwidth: Input memory (from main memory to dispc) bandwidth limit + in bytes per second + RFBI ---- diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt index 118a486c47bb..20861218649f 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt +++ b/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt @@ -36,6 +36,10 @@ Required properties: - clocks: handle to fclk - clock-names: "fck" +Optional properties: +- max-memory-bandwidth: Input memory (from main memory to dispc) bandwidth limit + in bytes per second + RFBI ---- diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt index 55492c264d17..b3408cc57be6 100644 --- a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -73,7 +73,7 @@ Hypervisor OS configuration: max-read-transactions = <31>; channel-reset-timeout-cycles = <0x500>; - hidma_24: dma-controller@0x5c050000 { + hidma_24: dma-controller@5c050000 { compatible = "qcom,hidma-1.0"; reg = <0 0x5c050000 0x0 0x1000>, <0 0x5c0b0000 0x0 0x1000>; @@ -85,7 +85,7 @@ Hypervisor OS configuration: Guest OS configuration: - hidma_24: dma-controller@0x5c050000 { + hidma_24: dma-controller@5c050000 { compatible = "qcom,hidma-1.0"; reg = <0 0x5c050000 0x0 0x1000>, <0 0x5c0b0000 0x0 0x1000>; diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt index aa7dbd565ad0..99ab5c4d331e 100644 --- a/Documentation/devicetree/bindings/dma/ste-dma40.txt +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -15,7 +15,7 @@ Optional properties: Example: - dma: dma-controller@801C0000 { + dma: dma-controller@801c0000 { compatible = "stericsson,db8500-dma40", "stericsson,dma40"; reg = <0x801C0000 0x1000 0x40010000 0x800>; reg-names = "base", "lcpa"; diff --git a/Documentation/devicetree/bindings/dma/zxdma.txt b/Documentation/devicetree/bindings/dma/zxdma.txt index abec59f35fde..0ab80f69e566 100644 --- a/Documentation/devicetree/bindings/dma/zxdma.txt +++ b/Documentation/devicetree/bindings/dma/zxdma.txt @@ -13,7 +13,7 @@ Required properties: Example: Controller: - dma: dma-controller@0x09c00000{ + dma: dma-controller@09c00000{ compatible = "zte,zx296702-dma"; reg = <0x09c00000 0x1000>; clocks = <&topclk ZX296702_DMA_ACLK>; diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt new file mode 100644 index 000000000000..1812c848e369 --- /dev/null +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -0,0 +1,78 @@ +EEPROMs (I2C) + +Required properties: + + - compatible: Must be a "<manufacturer>,<model>" pair. The following <model> + values are supported (assuming "atmel" as manufacturer): + + "atmel,24c00", + "atmel,24c01", + "atmel,24cs01", + "atmel,24c02", + "atmel,24cs02", + "atmel,24mac402", + "atmel,24mac602", + "atmel,spd", + "atmel,24c04", + "atmel,24cs04", + "atmel,24c08", + "atmel,24cs08", + "atmel,24c16", + "atmel,24cs16", + "atmel,24c32", + "atmel,24cs32", + "atmel,24c64", + "atmel,24cs64", + "atmel,24c128", + "atmel,24c256", + "atmel,24c512", + "atmel,24c1024", + + If <manufacturer> is not "atmel", then a fallback must be used + with the same <model> and "atmel" as manufacturer. + + Example: + compatible = "microchip,24c128", "atmel,24c128"; + + Supported manufacturers are: + + "catalyst", + "microchip", + "ramtron", + "renesas", + "nxp", + "st", + + Some vendors use different model names for chips which are just + variants of the above. Known such exceptions are listed below: + + "renesas,r1ex24002" - the fallback is "atmel,24c02" + + - reg: The I2C address of the EEPROM. + +Optional properties: + + - pagesize: The length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: This parameterless property disables writes to the eeprom. + + - size: Total eeprom size in bytes. + + - no-read-rollover: This parameterless property indicates that the + multi-address eeprom does not automatically roll over + reads to the next slave address. Please consult the + manual of your device. + + - wp-gpios: GPIO to which the write-protect pin of the chip is connected. + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + wp-gpios = <&gpio1 3 0>; +}; diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt index 1d3447165c37..e823d90b802f 100644 --- a/Documentation/devicetree/bindings/eeprom/at25.txt +++ b/Documentation/devicetree/bindings/eeprom/at25.txt @@ -1,7 +1,12 @@ EEPROMs (SPI) compatible with Atmel at25. Required properties: -- compatible : "atmel,at25". +- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25". + Example "<vendor>,<type>" values: + "microchip,25lc040" + "st,m95m02" + "st,m95256" + - reg : chip select number - spi-max-frequency : max spi frequency to use - pagesize : size of the eeprom page @@ -13,7 +18,7 @@ Optional properties: - spi-cpol : SPI inverse clock polarity, as per spi-bus bindings. - read-only : this parameter-less property disables writes to the eeprom -Obsolete legacy properties are can be used in place of "size", "pagesize", +Obsolete legacy properties can be used in place of "size", "pagesize", "address-width", and "read-only": - at25,byte-len : total eeprom size in bytes - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h @@ -22,8 +27,8 @@ Obsolete legacy properties are can be used in place of "size", "pagesize", Additional compatible properties are also allowed. Example: - at25@0 { - compatible = "atmel,at25", "st,m95256"; + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; reg = <0> spi-max-frequency = <5000000>; spi-cpha; diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt deleted file mode 100644 index 27f2bc15298a..000000000000 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ /dev/null @@ -1,47 +0,0 @@ -EEPROMs (I2C) - -Required properties: - - - compatible : should be "<manufacturer>,<type>", like these: - - "atmel,24c00", "atmel,24c01", "atmel,24c02", "atmel,24c04", - "atmel,24c08", "atmel,24c16", "atmel,24c32", "atmel,24c64", - "atmel,24c128", "atmel,24c256", "atmel,24c512", "atmel,24c1024" - - "catalyst,24c32" - - "microchip,24c128" - - "ramtron,24c64" - - "renesas,r1ex24002" - - The following manufacturers values have been deprecated: - "at", "at24" - - If there is no specific driver for <manufacturer>, a generic - device with <type> and manufacturer "atmel" should be used. - Possible types are: - "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", - "24c128", "24c256", "24c512", "24c1024", "spd" - - - reg : the I2C address of the EEPROM - -Optional properties: - - - pagesize : the length of the pagesize for writing. Please consult the - manual of your device, that value varies a lot. A wrong value - may result in data loss! If not specified, a safety value of - '1' is used which will be very slow. - - - read-only: this parameterless property disables writes to the eeprom - - - size: total eeprom size in bytes - -Example: - -eeprom@52 { - compatible = "atmel,24c32"; - reg = <0x52>; - pagesize = <32>; -}; diff --git a/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt index 00611aceed3e..a25c87b650e5 100644 --- a/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt @@ -21,7 +21,7 @@ Documentation/devicetree/bindings/gpio/gpio.txt Example: - gpioa: gpio@FF140000 { + gpioa: gpio@ff140000 { compatible = "abilis,tb10x-gpio"; interrupt-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt index 826a7208ca93..146e554b3c67 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-altera.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -30,7 +30,7 @@ Optional properties: Example: -gpio_altr: gpio@0xff200000 { +gpio_altr: gpio@ff200000 { compatible = "altr,pio-1.0"; reg = <0xff200000 0x10>; interrupts = <0 45 4>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 7f57271df2bc..0d0158728f89 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -27,7 +27,7 @@ Required properties: ti,tca6424 ti,tca9539 ti,tca9554 - onsemi,pca9654 + onnn,pca9654 exar,xra1202 Optional properties: diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt index 854de130a971..78458adbf4b7 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt @@ -27,7 +27,7 @@ Optional properties: Example: -gpio1: stp@E100BB0 { +gpio1: stp@e100bb0 { compatible = "lantiq,gpio-stp-xway"; reg = <0xE100BB0 0x40>; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 802402f6cc5d..b5de08e3b1a2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -290,7 +290,7 @@ pins 50..69. Example 2: - gpio_pio_i: gpio-controller@14B0 { + gpio_pio_i: gpio-controller@14b0 { #gpio-cells = <2>; compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; reg = <0x1480 0x18>; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index c6814d7cc2b2..ad876548ab5d 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -17,6 +17,7 @@ Required properties: + rockchip,rk3066-mali + rockchip,rk3188-mali + rockchip,rk3228-mali + + rockchip,rk3328-mali + stericsson,db8500-mali - reg: Physical base address and length of the GPU registers diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt index 367c8203213b..3ac02988a1a5 100644 --- a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt @@ -22,8 +22,9 @@ Required properties for pwm-tacho node: - compatible : should be "aspeed,ast2400-pwm-tacho" for AST2400 and "aspeed,ast2500-pwm-tacho" for AST2500. -- clocks : a fixed clock providing input clock frequency(PWM - and Fan Tach clock) +- clocks : phandle to clock provider with the clock number in the second cell + +- resets : phandle to reset controller with the reset number in the second cell fan subnode format: =================== @@ -48,19 +49,14 @@ Required properties for each child node: Examples: -pwm_tacho_fixed_clk: fixedclk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24000000>; -}; - pwm_tacho: pwmtachocontroller@1e786000 { #address-cells = <1>; #size-cells = <1>; #cooling-cells = <2>; reg = <0x1E786000 0x1000>; compatible = "aspeed,ast2500-pwm-tacho"; - clocks = <&pwm_tacho_fixed_clk>; + clocks = <&syscon ASPEED_CLK_APB>; + resets = <&syscon ASPEED_RESET_PWM>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>; diff --git a/Documentation/devicetree/bindings/hwmon/jc42.txt b/Documentation/devicetree/bindings/hwmon/jc42.txt index 07a250498fbb..f569db58f64a 100644 --- a/Documentation/devicetree/bindings/hwmon/jc42.txt +++ b/Documentation/devicetree/bindings/hwmon/jc42.txt @@ -34,6 +34,10 @@ Required properties: - reg: I2C address +Optional properties: +- smbus-timeout-disable: When set, the smbus timeout function will be disabled. + This is not supported on all chips. + Example: temp-sensor@1a { diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index 248a155414c2..548a73cde796 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -54,7 +54,7 @@ Optional properties: Example: - i2c@12CA0000 { + i2c@12ca0000 { compatible = "acme,some-i2c-device"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt index 70c054a9a997..60fe90d69f4e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -11,7 +11,7 @@ Required properties: Examples: -lpi2c7: lpi2c7@40A50000 { +lpi2c7: lpi2c7@40a50000 { compatible = "fsl,imx8dv-lpi2c"; reg = <0x40A50000 0x10000>; interrupt-parent = <&intc>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt index 231e4cc4008c..d4a082acf92f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt @@ -18,7 +18,7 @@ Optional properties: Example / { - i2c4: i2c4@0x10054000 { + i2c4: i2c4@10054000 { compatible = "ingenic,jz4780-i2c"; reg = <0x10054000 0x1000>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt index ff7bf37deb43..e199695b1c96 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt @@ -5,6 +5,7 @@ The MediaTek's I2C controller is used to interface with I2C devices. Required properties: - compatible: value should be either of the following. "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701 + "mediatek,mt2712-i2c": for MediaTek MT2712 "mediatek,mt6577-i2c": for MediaTek MT6577 "mediatek,mt6589-i2c": for MediaTek MT6589 "mediatek,mt7622-i2c": for MediaTek MT7622 diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt index aa097045a10e..34d91501342e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -1,10 +1,19 @@ * NXP PCA954x I2C bus switch +The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. + Required Properties: - compatible: Must contain one of the following. - "nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544", - "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548" + "nxp,pca9540", + "nxp,pca9542", + "nxp,pca9543", + "nxp,pca9544", + "nxp,pca9545", + "nxp,pca9546", "nxp,pca9846", + "nxp,pca9547", "nxp,pca9847", + "nxp,pca9548", "nxp,pca9848", + "nxp,pca9849" - reg: The I2C address of the device. diff --git a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt new file mode 100644 index 000000000000..e9ebb8a20e0d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt @@ -0,0 +1,13 @@ +Device-Tree bindings for sigma delta modulator + +Required properties: +- compatible: should be "ads1201", "sd-modulator". "sd-modulator" can be use + as a generic SD modulator if modulator not specified in compatible list. +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers". + +Example node: + + ads1202: adc@0 { + compatible = "sd-modulator"; + #io-channel-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt new file mode 100644 index 000000000000..911492da48f3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt @@ -0,0 +1,128 @@ +STMicroelectronics STM32 DFSDM ADC device driver + + +STM32 DFSDM ADC is a sigma delta analog-to-digital converter dedicated to +interface external sigma delta modulators to STM32 micro controllers. +It is mainly targeted for: +- Sigma delta modulators (motor control, metering...) +- PDM microphones (audio digital microphone) + +It features up to 8 serial digital interfaces (SPI or Manchester) and +up to 4 filters on stm32h7. + +Each child node match with a filter instance. + +Contents of a STM32 DFSDM root node: +------------------------------------ +Required properties: +- compatible: Should be "st,stm32h7-dfsdm". +- reg: Offset and length of the DFSDM block register set. +- clocks: IP and serial interfaces clocking. Should be set according + to rcc clock ID and "clock-names". +- clock-names: Input clock name "dfsdm" must be defined, + "audio" is optional. If defined CLKOUT is based on the audio + clock, else "dfsdm" is used. +- #interrupt-cells = <1>; +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- spi-max-frequency: Requested only for SPI master mode. + SPI clock OUT frequency (Hz). This clock must be set according + to "clock" property. Frequency must be a multiple of the rcc + clock frequency. If not, SPI CLKOUT frequency will not be + accurate. + +Contents of a STM32 DFSDM child nodes: +-------------------------------------- + +Required properties: +- compatible: Must be: + "st,stm32-dfsdm-adc" for sigma delta ADCs + "st,stm32-dfsdm-dmic" for audio digital microphone. +- reg: Specifies the DFSDM filter instance used. +- interrupts: IRQ lines connected to each DFSDM filter instance. +- st,adc-channels: List of single-ended channels muxed for this ADC. + valid values: + "st,stm32h7-dfsdm" compatibility: 0 to 7. +- st,adc-channel-names: List of single-ended channel names. +- st,filter-order: SinC filter order from 0 to 5. + 0: FastSinC + [1-5]: order 1 to 5. + For audio purpose it is recommended to use order 3 to 5. +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers". + +Required properties for "st,stm32-dfsdm-adc" compatibility: +- io-channels: From common IIO binding. Used to pipe external sigma delta + modulator or internal ADC output to DFSDM channel. + This is not required for "st,stm32-dfsdm-pdm" compatibility as + PDM microphone is binded in Audio DT node. + +Required properties for "st,stm32-dfsdm-pdm" compatibility: +- #sound-dai-cells: Must be set to 0. +- dma: DMA controller phandle and DMA request line associated to the + filter instance (specified by the field "reg") +- dma-names: Must be "rx" + +Optional properties: +- st,adc-channel-types: Single-ended channel input type. + - "SPI_R": SPI with data on rising edge (default) + - "SPI_F": SPI with data on falling edge + - "MANCH_R": manchester codec, rising edge = logic 0 + - "MANCH_F": manchester codec, falling edge = logic 1 +- st,adc-channel-clk-src: Conversion clock source. + - "CLKIN": external SPI clock (CLKIN x) + - "CLKOUT": internal SPI clock (CLKOUT) (default) + - "CLKOUT_F": internal SPI clock divided by 2 (falling edge). + - "CLKOUT_R": internal SPI clock divided by 2 (rising edge). + +- st,adc-alt-channel: Must be defined if two sigma delta modulator are + connected on same SPI input. + If not set, channel n is connected to SPI input n. + If set, channel n is connected to SPI input n + 1. + +- st,filter0-sync: Set to 1 to synchronize with DFSDM filter instance 0. + Used for multi microphones synchronization. + +Example of a sigma delta adc connected on DFSDM SPI port 0 +and a pdm microphone connected on DFSDM SPI port 1: + + ads1202: simple_sd_adc@0 { + compatible = "ads1202"; + #io-channel-cells = <1>; + }; + + dfsdm: dfsdm@40017000 { + compatible = "st,stm32h7-dfsdm"; + reg = <0x40017000 0x400>; + clocks = <&rcc DFSDM1_CK>; + clock-names = "dfsdm"; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + dfsdm_adc0: filter@0 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <0>; + interrupts = <110>; + st,adc-channels = <0>; + st,adc-channel-names = "sd_adc0"; + st,adc-channel-types = "SPI_F"; + st,adc-channel-clk-src = "CLKOUT"; + io-channels = <&ads1202 0>; + st,filter-order = <3>; + }; + dfsdm_pdm1: filter@1 { + compatible = "st,stm32-dfsdm-dmic"; + reg = <1>; + interrupts = <111>; + dmas = <&dmamux1 102 0x400 0x00>; + dma-names = "rx"; + st,adc-channels = <1>; + st,adc-channel-names = "dmic1"; + st,adc-channel-types = "SPI_R"; + st,adc-channel-clk-src = "CLKOUT"; + st,filter-order = <5>; + }; + } diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt index 54e7e70bcea5..831dbee7a5c3 100644 --- a/Documentation/devicetree/bindings/iio/pressure/hp03.txt +++ b/Documentation/devicetree/bindings/iio/pressure/hp03.txt @@ -10,7 +10,7 @@ Required properties: Example: -hp03@0x77 { +hp03@77 { compatible = "hoperf,hp03"; reg = <0x77>; xclr-gpio = <&portc 0 0x0>; diff --git a/Documentation/devicetree/bindings/input/hid-over-i2c.txt b/Documentation/devicetree/bindings/input/hid-over-i2c.txt index 28e8bd8b7d64..4d3da9d91de4 100644 --- a/Documentation/devicetree/bindings/input/hid-over-i2c.txt +++ b/Documentation/devicetree/bindings/input/hid-over-i2c.txt @@ -31,7 +31,7 @@ device-specific compatible properties, which should be used in addition to the - vdd-supply: phandle of the regulator that provides the supply voltage. - post-power-on-delay-ms: time required by the device after enabling its regulators - before it is ready for communication. Must be used with 'vdd-supply'. + or powering it on, before it is ready for communication. Example: diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt index 5305e74e5742..4c5c0a82586d 100644 --- a/Documentation/devicetree/bindings/input/samsung-keypad.txt +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -45,7 +45,7 @@ Optional Properties specific to linux: Example: - keypad@100A0000 { + keypad@100a0000 { compatible = "samsung,s5pv210-keypad"; reg = <0x100A0000 0x100>; interrupts = <173>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt index ac5dff412e25..f127a2117072 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -66,7 +66,7 @@ Example: An example of touchscreen node reg = <0x180a6000 0xc30>; }; - touchscreen: touchscreen@180A6000 { + touchscreen: touchscreen@180a6000 { compatible = "brcm,iproc-touchscreen"; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt index ca5a2c86480c..56d835242af2 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -15,7 +15,7 @@ Optional properties: Example: i2c@80110000 { - bu21013_tp@0x5c { + bu21013_tp@5c { compatible = "rohm,bu21013_tp"; reg = <0x5c>; touch-gpio = <&gpio2 20 0x4>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt index 6aa625e0cb8d..84752de12412 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -23,6 +23,8 @@ Optional properties: - touchscreen-inverted-y : See touchscreen.txt - touchscreen-swapped-x-y : See touchscreen.txt - silead,max-fingers : maximum number of fingers the touchscreen can detect +- silead,home-button : Boolean, set to true on devices which have a + capacitive home-button build into the touchscreen - vddio-supply : regulator phandle for controller VDDIO - avdd-supply : regulator phandle for controller AVDD diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 560d8a727b8f..2f3244648646 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -155,7 +155,7 @@ Example: <0x0 0xe112f000 0 0x02000>, <0x0 0xe1140000 0 0x10000>, <0x0 0xe1160000 0 0x10000>; - v2m0: v2m@0x8000 { + v2m0: v2m@8000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x80000 0 0x1000>; @@ -163,7 +163,7 @@ Example: .... - v2mN: v2m@0x9000 { + v2mN: v2m@9000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x90000 0 0x1000>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt index 80994adab392..42431f44697f 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt @@ -71,7 +71,7 @@ Example 2: * An interrupt generating device that is wired to a Meta external * trigger block. */ - uart1: uart@0x02004c00 { + uart1: uart@02004c00 { // Interrupt source '5' that is level-sensitive. // Note that there are only two cells as specified in the // interrupt parent's '#interrupt-cells' property. diff --git a/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt index a69118550344..5dc2a55ad811 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt @@ -51,7 +51,7 @@ Example 1: /* * TZ1090 PDC block */ - pdc: pdc@0x02006000 { + pdc: pdc@02006000 { // This is an interrupt controller node. interrupt-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt b/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt index 715a013ed4bd..2ab0ea39867b 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt @@ -39,7 +39,7 @@ Example: The following is an example from the SPEAr320 SoC dtsi file. -shirq: interrupt-controller@0xb3000000 { +shirq: interrupt-controller@b3000000 { compatible = "st,spear320-shirq"; reg = <0xb3000000 0x1000>; interrupts = <28 29 30 1>; diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 857df929a654..1fd5d69647ca 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -16,6 +16,9 @@ Required Properties: - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. - "renesas,ipmmu-r8a7795" for the R8A7795 (R-Car H3) IPMMU. + - "renesas,ipmmu-r8a7796" for the R8A7796 (R-Car M3-W) IPMMU. + - "renesas,ipmmu-r8a77970" for the R8A77970 (R-Car V3M) IPMMU. + - "renesas,ipmmu-r8a77995" for the R8A77995 (R-Car D3) IPMMU. - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. - reg: Base address and size of the IPMMU registers. diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt index 85f068805dd8..b1682c80b490 100644 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -56,7 +56,7 @@ Examples: iommus = <&sysmmu_gsc0>; }; - sysmmu_gsc0: sysmmu@13E80000 { + sysmmu_gsc0: sysmmu@13e80000 { compatible = "samsung,exynos-sysmmu"; reg = <0x13E80000 0x1000>; interrupt-parent = <&combiner>; diff --git a/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt b/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt index c2619797ce0c..49cfc8c337c4 100644 --- a/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt @@ -14,7 +14,7 @@ Optional properties: depends on the interrupt controller parent. Example: - mbox_tx: mailbox@0x100 { + mbox_tx: mailbox@100 { compatible = "altr,mailbox-1.0"; reg = <0x100 0x8>; interrupt-parent = < &gic_0 >; @@ -22,7 +22,7 @@ Example: #mbox-cells = <1>; }; - mbox_rx: mailbox@0x200 { + mbox_rx: mailbox@200 { compatible = "altr,mailbox-1.0"; reg = <0x200 0x8>; interrupt-parent = < &gic_0 >; @@ -40,7 +40,7 @@ support only one channel).The equivalent "mbox-names" property value can be used to give a name to the communication channel to be used by the client user. Example: - mclient0: mclient0@0x400 { + mclient0: mclient0@400 { compatible = "client-1.0"; reg = <0x400 0x10>; mbox-names = "mbox-tx", "mbox-rx"; diff --git a/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt index 0f3ee81d92c2..9bcdf2087625 100644 --- a/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt +++ b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt @@ -15,7 +15,7 @@ Optional properties: - brcm,use-bcm-hdr: present if a BCM header precedes each frame. Example: - pdc0: iproc-pdc0@0x612c0000 { + pdc0: iproc-pdc0@612c0000 { compatible = "brcm,iproc-pdc-mbox"; reg = <0 0x612c0000 0 0x445>; /* PDC FS0 regs */ interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt index 9b40c4925aa9..0ef372656a3e 100644 --- a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt @@ -124,7 +124,7 @@ dsp { }; /* AM33xx */ -mailbox: mailbox@480C8000 { +mailbox: mailbox@480c8000 { compatible = "ti,omap4-mailbox"; reg = <0x480C8000 0x200>; interrupts = <77>; diff --git a/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt b/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt index c3b55b3ede8a..ebf0e3710cee 100644 --- a/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt +++ b/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt @@ -20,9 +20,9 @@ Required properties: order referring to the transfer path. - interrupt-names: Contains interrupt names matching the rx transfer path for a given SoC. Receive interrupts shall be of the - format: "rx_<QID>_<PID>". + format: "rx_<QID>". For ti,k2g-message-manager, this shall contain: - "rx_005_002", "rx_057_002" + "rx_005", "rx_057" - interrupts: Contains the interrupt information corresponding to interrupt-names property. diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 0d4fdaedc6f1..bc963a6d305a 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -17,7 +17,7 @@ Optional properties: Example: -gsc_0: gsc@0x13e00000 { +gsc_0: gsc@13e00000 { compatible = "samsung,exynos5250-gsc"; reg = <0x13e00000 0x1000>; interrupts = <0 85 0>; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt index ed5a334b1e57..6b910036b57e 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -6,6 +6,8 @@ interface. Required Properties: - compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -16,6 +18,8 @@ Example: mt9m111@5d { compatible = "micron,mt9m111"; reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; remote = <&pxa_camera>; port { diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt index 540b36c4b1f2..8e36da0d8406 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -1,4 +1,4 @@ -* Omnivision OV5640 MIPI CSI-2 sensor +* Omnivision OV5640 MIPI CSI-2 / parallel sensor Required Properties: - compatible: should be "ovti,ov5640" @@ -18,7 +18,25 @@ The device node must contain one 'port' child node for its digital output video port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. -Example: +OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0) +- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) + +Endpoint node required properties for parallel connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- bus-width: shall be set to <8> for 8 bits parallel bus + or <10> for 10 bits parallel bus +- data-shift: shall be set to <2> for 8 bits parallel bus + (lines 9:2 are used) or <0> for 10 bits parallel bus +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. + +Examples: &i2c1 { ov5640: camera@3c { @@ -35,6 +53,7 @@ Example: reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; port { + /* MIPI CSI-2 bus endpoint */ ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_from_ov5640>; clock-lanes = <0>; @@ -43,3 +62,26 @@ Example: }; }; }; + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt new file mode 100644 index 000000000000..af781c3a5f0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt index 0b7b6a4d84ff..e80d5891b7ed 100644 --- a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -20,6 +20,13 @@ Mandatory properties is in hardware standby mode when the signal is in the low state. +Optional properties +------------------- + +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + + Endpoint node mandatory properties ---------------------------------- diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 46c15c54175d..2a615d84a682 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -68,7 +68,7 @@ vcodec_dec: vcodec@16000000 { "vdec_bus_clk_src"; }; - vcodec_enc: vcodec@0x18002000 { + vcodec_enc: vcodec@18002000 { compatible = "mediatek,mt8173-vcodec-enc"; reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt new file mode 100644 index 000000000000..470237ed6fe5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt @@ -0,0 +1,55 @@ +NVIDIA Tegra Video Decoder Engine + +Required properties: +- compatible : Must contain one of the following values: + - "nvidia,tegra20-vde" + - "nvidia,tegra30-vde" + - "nvidia,tegra114-vde" + - "nvidia,tegra124-vde" + - "nvidia,tegra132-vde" +- reg : Must contain an entry for each entry in reg-names. +- reg-names : Must include the following entries: + - sxe + - bsev + - mbe + - ppe + - mce + - tfe + - ppb + - vdma + - frameid +- iram : Must contain phandle to the mmio-sram device node that represents + IRAM region used by VDE. +- interrupts : Must contain an entry for each entry in interrupt-names. +- interrupt-names : Must include the following entries: + - sync-token + - bsev + - sxe +- clocks : Must include the following entries: + - vde +- resets : Must include the following entries: + - vde + +Example: + +video-codec@6001a000 { + compatible = "nvidia,tegra20-vde"; + reg = <0x6001a000 0x1000 /* Syntax Engine */ + 0x6001b000 0x1000 /* Video Bitstream Engine */ + 0x6001c000 0x100 /* Macroblock Engine */ + 0x6001c200 0x100 /* Post-processing Engine */ + 0x6001c400 0x100 /* Motion Compensation Engine */ + 0x6001c600 0x100 /* Transform Engine */ + 0x6001c800 0x100 /* Pixel prediction block */ + 0x6001ca00 0x100 /* Video DMA */ + 0x6001d800 0x300 /* Video frame controls */>; + reg-names = "sxe", "bsev", "mbe", "ppe", "mce", + "tfe", "ppb", "vdma", "frameid"; + iram = <&vde_pool>; /* IRAM region */ + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, /* Sync token interrupt */ + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, /* BSE-V interrupt */ + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */ + interrupt-names = "sync-token", "bsev", "sxe"; + clocks = <&tegra_car TEGRA20_CLK_VDE>; + resets = <&tegra_car 61>; +}; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 6e4ef8caf759..19357d0bbe65 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -44,7 +44,7 @@ Device node example vin0 = &vin0; }; - vin0: vin@0xe6ef0000 { + vin0: vin@e6ef0000 { compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; clocks = <&mstp8_clks R8A7790_CLK_VIN0>; reg = <0 0xe6ef0000 0 0x1000>; diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt index 6f3756da900f..e847291d4aff 100644 --- a/Documentation/devicetree/bindings/media/s5p-cec.txt +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -23,7 +23,7 @@ Optional: Example: -hdmicec: cec@100B0000 { +hdmicec: cec@100b0000 { compatible = "samsung,s5p-cec"; reg = <0x100B0000 0x200>; interrupts = <0 114 0>; diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt index e4e15d8d7521..48c599dacbdf 100644 --- a/Documentation/devicetree/bindings/media/samsung-fimc.txt +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -138,7 +138,7 @@ Example: }; /* MIPI CSI-2 bus IF sensor */ - s5c73m3: sensor@0x1a { + s5c73m3: sensor@1a { compatible = "samsung,s5c73m3"; reg = <0x1a>; vddio-supply = <...>; diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt index 2c85c4538a6d..21f31fdf5543 100644 --- a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt +++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt @@ -62,7 +62,7 @@ For more details see description of the SPI busses bindings Example: -i2c@138A000000 { +i2c@138a000000 { ... s5c73m3@3c { compatible = "samsung,s5c73m3"; diff --git a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt index 1ce4e46bcbb7..17a8e81ca0cc 100644 --- a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt +++ b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt @@ -8,7 +8,7 @@ Bindings, specific for the sh_mobile_ceu_camera.c driver: Example: -ceu0: ceu@0xfe910000 { +ceu0: ceu@fe910000 { compatible = "renesas,sh-mobile-ceu"; reg = <0xfe910000 0xa0>; interrupt-parent = <&intcs>; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 3994b0143dd1..258b8dfddf48 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -154,7 +154,7 @@ imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a 'port' node which may indicate that at any time only one of the following data pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. - ceu0: ceu@0xfe910000 { + ceu0: ceu@fe910000 { compatible = "renesas,sh-mobile-ceu"; reg = <0xfe910000 0xa0>; interrupts = <0x880>; @@ -193,9 +193,9 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - i2c0: i2c@0xfff20000 { + i2c0: i2c@fff20000 { ... - ov772x_1: camera@0x21 { + ov772x_1: camera@21 { compatible = "ovti,ov772x"; reg = <0x21>; vddio-supply = <®ulator1>; @@ -219,7 +219,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - imx074: camera@0x1a { + imx074: camera@1a { compatible = "sony,imx074"; reg = <0x1a>; vddio-supply = <®ulator1>; @@ -239,7 +239,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - csi2: csi2@0xffc90000 { + csi2: csi2@ffc90000 { compatible = "renesas,sh-mobile-csi2"; reg = <0xffc90000 0x1000>; interrupts = <0x17a0>; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt index 9dd86b3db937..439351ab2a79 100644 --- a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -66,6 +66,6 @@ Example: tpg1_out: endpoint { remote-endpoint = <&switch_in0>; }; - }: + }; }; }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt index 8dbe47013c2b..14968b048cd3 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt @@ -12,6 +12,8 @@ Required properties: - clock-names: Must include the following entries: - mc: the module's clock input - interrupts: The interrupt outputs from the controller. + +Required properties for Tegra30, Tegra114, Tegra124, Tegra132 and Tegra210: - #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines the SWGROUP of the master. diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt index 9592717f483f..190437a0c146 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt @@ -138,7 +138,7 @@ from the corresponding HW reg. Example for aemif, davinci nand and nor flash chip select shown below. -memory-controller@21000A00 { +memory-controller@21000a00 { compatible = "ti,davinci-aemif"; #address-cells = <2>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt index fd823d6091b2..621b41c79faa 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -23,6 +23,13 @@ Required properties: the value shall be "emif<n>" where <n> is the number of the EMIF instance with base 1. +Required only for "ti,emif-am3352" and "ti,emif-am4372": +- sram : Phandles for generic sram driver nodes, + first should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.txt + for more details. + Optional properties: - cs1-used : Have this property if CS1 of this EMIF instance has a memory part attached to it. If there is a memory @@ -44,9 +51,9 @@ Optional properties: - hw-caps-temp-alert : Have this property if the controller has capability for generating SDRAM temperature alerts -Example: +-Examples: -emif1: emif@0x4c000000 { +emif1: emif@4c000000 { compatible = "ti,emif-4d"; ti,hwmods = "emif2"; phy-type = <1>; @@ -56,3 +63,11 @@ emif1: emif@0x4c000000 { hw-caps-ll-interface; hw-caps-temp-alert; }; + +/* From am33xx.dtsi */ +emif: emif@4c000000 { + compatible = "ti,emif-am3352"; + reg = <0x4C000000 0x1000>; + sram = <&pm_sram_code + &pm_sram_data>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-tcb.txt b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt new file mode 100644 index 000000000000..c4a83e364cb6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt @@ -0,0 +1,56 @@ +* Device tree bindings for Atmel Timer Counter Blocks +- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon". + <chip> can be "at91rm9200" or "at91sam9x5" +- reg: Should contain registers location and length +- #address-cells: has to be 1 +- #size-cells: has to be 0 +- interrupts: Should contain all interrupts for the TC block + Note that you can specify several interrupt cells if the TC + block has one interrupt per channel. +- clock-names: tuple listing input clock names. + Required elements: "t0_clk", "slow_clk" + Optional elements: "t1_clk", "t2_clk" +- clocks: phandles to input clocks. + +The TCB can expose multiple subdevices: + * a timer + - compatible: Should be "atmel,tcb-timer" + - reg: Should contain the TCB channels to be used. If the + counter width is 16 bits (at91rm9200-tcb), two consecutive + channels are needed. Else, only one channel will be used. + +Examples: + +One interrupt per TC block: + tcb0: timer@fff7c000 { + compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfff7c000 0x100>; + interrupts = <18 4>; + clocks = <&tcb0_clk>, <&clk32k>; + clock-names = "t0_clk", "slow_clk"; + + timer@0 { + compatible = "atmel,tcb-timer"; + reg = <0>, <1>; + }; + + timer@2 { + compatible = "atmel,tcb-timer"; + reg = <2>; + }; + }; + +One interrupt per TC channel in a TC block: + tcb1: timer@fffdc000 { + compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfffdc000 0x100>; + interrupts = <26 4>, <27 4>, <28 4>; + clocks = <&tcb1_clk>, <&clk32k>; + clock-names = "t0_clk", "slow_clk"; + }; + + diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt index 136e0c2da44d..6245c9b1a68b 100644 --- a/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -41,7 +41,7 @@ Optional properties (all): Example for I2C: -i2c@12CA0000 { +i2c@12ca0000 { cros-ec@1e { reg = <0x1e>; compatible = "google,cros-ec-i2c"; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index ac235fe385fc..8261ea73278a 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -130,7 +130,7 @@ ecspi@70010000 { /* ECSPI1 */ #size-cells = <0>; led-control = <0x000 0x000 0x0e0 0x000>; - sysled { + sysled@3 { reg = <3>; label = "system:red:live"; linux,default-trigger = "heartbeat"; diff --git a/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt index 20963c76b4bc..71a1f5963936 100644 --- a/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt +++ b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt @@ -13,7 +13,7 @@ Required properties: Example: -devctrl: device-state-control@0x02620000 { +devctrl: device-state-control@02620000 { compatible = "ti,keystone-devctrl", "syscon"; reg = <0x02620000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt index 6c9f176f3571..05b47232ed9e 100644 --- a/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt +++ b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt @@ -9,7 +9,7 @@ Required properties: - reg : Location and size of bounce buffer Example: - smc@0x3404c000 { + smc@3404c000 { compatible = "brcm,bcm11351-smc", "brcm,kona-smc"; reg = <0x3404c000 0x400>; //1 KiB in SRAM }; diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt new file mode 100644 index 000000000000..892ba4384abc --- /dev/null +++ b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt @@ -0,0 +1,12 @@ +NVIDIA Tegra186 MISC register block + +The MISC register block found on Tegra186 SoCs contains registers that can be +used to identify a given chip and various strapping options. + +Required properties: +- compatible: Must be: + - Tegra186: "nvidia,tegra186-misc" +- reg: Should contain 2 entries: The first entry gives the physical address + and length of the register region which contains revision and debug + features. The second entry specifies the physical address and length + of the register region indicating the strapping options. diff --git a/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt index aaba2483b4ff..7f5dd83f5bd9 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt @@ -12,7 +12,7 @@ Refer to clocks/clock-bindings.txt for generic clock consumer properties. Example: -sdio2: sdio@0x3f1a0000 { +sdio2: sdio@3f1a0000 { compatible = "brcm,kona-sdhci"; reg = <0x3f1a0000 0x10000>; clocks = <&sdio3_clk>; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index 954561d09a8e..fa90d253dc7e 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -24,7 +24,7 @@ Optional properties: Example: -sdhci0: sdhci@0x18041000 { +sdhci0: sdhci@18041000 { compatible = "brcm,sdhci-iproc-cygnus"; reg = <0x18041000 0x100>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index fb11ae8b3b72..467cd7b147ce 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -67,10 +67,10 @@ logic applies to the "wp-inverted" property. CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of dedicated pins can be specified, using *-inverted properties. GPIO polarity can -also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity +also be specified using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. This means, the two properties are "superimposed," for example leaving the -OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted +GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted property property results in a double-inversion and actually means the "normal" line polarity is in effect. diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index 72d2a734ab85..9b8017670870 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -12,6 +12,8 @@ Required properties: "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 + "mediatek,mt7623-mmc", "mediatek,mt2701-mmc": for MT7623 SoC + - reg: physical base address of the controller and length - interrupts: Should contain MSDC interrupt number - clocks: Should contain phandle for the clock feeding the MMC controller diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 3a4ac401e6f9..19f5508a7569 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -55,7 +55,7 @@ Examples: [hwmod populated DMA resources] - mmc1: mmc@0x4809c000 { + mmc1: mmc@4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; @@ -67,7 +67,7 @@ Examples: [generic DMA request binding] - mmc1: mmc@0x4809c000 { + mmc1: mmc@4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 3c6762430fd9..d8685cb83325 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,6 +26,7 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index c34aa6f8a424..63d4d626fbd5 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -12,7 +12,7 @@ Required properties: - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" - interrupts : Should contain the interrupt for the device - clocks : The clocks needed by the QuadSPI controller - - clock-names : the name of the clocks + - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi". Optional properties: - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B. diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt index 131d3a74d0bd..c8567b40fe13 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt @@ -82,15 +82,15 @@ gpmc: gpmc@6e000000 { label = "bootloader-nor"; reg = <0 0x40000>; }; - partition@0x40000 { + partition@40000 { label = "params-nor"; reg = <0x40000 0x40000>; }; - partition@0x80000 { + partition@80000 { label = "kernel-nor"; reg = <0x80000 0x200000>; }; - partition@0x280000 { + partition@280000 { label = "filesystem-nor"; reg = <0x240000 0x7d80000>; }; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 376fa2f50e6b..956bb046e599 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -13,7 +13,6 @@ Required properties: at25df321a at25df641 at26df081a - en25s64 mr25h128 mr25h256 mr25h10 @@ -33,7 +32,6 @@ Required properties: s25fl008k s25fl064k sst25vf040b - sst25wf040b m25p40 m25p80 m25p16 diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt index d0a37252eb22..6d60bc3063f5 100644 --- a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt @@ -23,7 +23,7 @@ Optional subnodes: Example: - mlc: flash@200A8000 { + mlc: flash@200a8000 { compatible = "nxp,lpc3220-mlc"; reg = <0x200A8000 0x11000>; interrupts = <11 0>; diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt index dbf9e054c11c..1c88526dedfc 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -12,8 +12,10 @@ tree nodes. The first part of NFC is NAND Controller Interface (NFI) HW. Required NFI properties: -- compatible: Should be one of "mediatek,mt2701-nfc", - "mediatek,mt2712-nfc". +- compatible: Should be one of + "mediatek,mt2701-nfc", + "mediatek,mt2712-nfc", + "mediatek,mt7622-nfc". - reg: Base physical address and size of NFI. - interrupts: Interrupts of NFI. - clocks: NFI required clocks. @@ -131,7 +133,7 @@ Example: read-only; reg = <0x00000000 0x00400000>; }; - android@0x00400000 { + android@00400000 { label = "android"; reg = <0x00400000 0x12c00000>; }; @@ -142,7 +144,10 @@ Example: ============== Required BCH properties: -- compatible: Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc". +- compatible: Should be one of + "mediatek,mt2701-ecc", + "mediatek,mt2712-ecc", + "mediatek,mt7622-ecc". - reg: Base physical address and size of ECC. - interrupts: Interrupts of ECC. - clocks: ECC required clocks. diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt index a706297998e9..0e21df94a53f 100644 --- a/Documentation/devicetree/bindings/net/altera_tse.txt +++ b/Documentation/devicetree/bindings/net/altera_tse.txt @@ -52,7 +52,7 @@ Optional properties: Example: - tse_sub_0_eth_tse_0: ethernet@0x1,00000000 { + tse_sub_0_eth_tse_0: ethernet@1,00000000 { compatible = "altr,tse-msgdma-1.0"; reg = <0x00000001 0x00000000 0x00000400>, <0x00000001 0x00000460 0x00000020>, @@ -90,7 +90,7 @@ Example: }; }; - tse_sub_1_eth_tse_0: ethernet@0x1,00001000 { + tse_sub_1_eth_tse_0: ethernet@1,00001000 { compatible = "altr,tse-msgdma-1.0"; reg = <0x00000001 0x00001000 0x00000400>, <0x00000001 0x00001460 0x00000020>, diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index 9a734d808aa7..b7336b9d6a3c 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -2,7 +2,10 @@ Required properties: -- compatible: should be "brcm,bcm7445-switch-v4.0" or "brcm,bcm7278-switch-v4.0" +- compatible: should be one of + "brcm,bcm7445-switch-v4.0" + "brcm,bcm7278-switch-v4.0" + "brcm,bcm7278-switch-v4.8" - reg: addresses and length of the register sets for the device, must be 6 pairs of register addresses and lengths - interrupts: interrupts for the devices, must be two interrupts diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index 56d6cc336e1c..bfc0c433654f 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -18,6 +18,12 @@ Optional properties: - xceiver-supply: Regulator that powers the CAN transceiver +- big-endian: This means the registers of FlexCAN controller are big endian. + This is optional property.i.e. if this property is not present in + device tree node then controller is assumed to be little endian. + if this property is present then controller is assumed to be big + endian. + Example: can@1c000 { diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 7cc15c96ea95..4cb4925a28ab 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -61,7 +61,7 @@ file. Examples: - mac: ethernet@4A100000 { + mac: ethernet@4a100000 { compatible = "ti,cpsw"; reg = <0x4A100000 0x1000>; interrupts = <55 0x4>; @@ -91,7 +91,7 @@ Examples: }; (or) - mac: ethernet@4A100000 { + mac: ethernet@4a100000 { compatible = "ti,cpsw"; ti,hwmods = "cpgmac0"; cpdma_channels = <8>; diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 621156ca4ffd..e6527de80f10 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -21,7 +21,7 @@ file. Examples: - mdio: davinci_mdio@4A101000 { + mdio: davinci_mdio@4a101000 { compatible = "ti,davinci_mdio"; reg = <0x4A101000 0x1000>; bus_freq = <1000000>; @@ -29,7 +29,7 @@ Examples: (or) - mdio: davinci_mdio@4A101000 { + mdio: davinci_mdio@4a101000 { compatible = "ti,davinci_mdio"; ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index f0dc94409107..2d41fb96ce0a 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -59,7 +59,7 @@ ethernet@83fec000 { reg = <0x83fec000 0x4000>; interrupts = <87>; phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ local-mac-address = [00 04 9F 01 1B B9]; phy-supply = <®_fec_supply>; }; @@ -71,7 +71,7 @@ ethernet@83fec000 { reg = <0x83fec000 0x4000>; interrupts = <87>; phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ local-mac-address = [00 04 9F 01 1B B9]; phy-supply = <®_fec_supply>; phy-handle = <ðphy>; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index db74f0dc290c..594982c6b9f9 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -136,7 +136,7 @@ Clock Properties: Example: - ptp_clock@24E00 { + ptp_clock@24e00 { compatible = "fsl,etsec-ptp"; reg = <0x24E00 0xB0>; interrupts = <12 0x8 13 0x8>; diff --git a/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt index dea5124cdc52..d24172cc6d32 100644 --- a/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt +++ b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt @@ -1,7 +1,7 @@ * ADF7242 IEEE 802.15.4 * Required properties: - - compatible: should be "adi,adf7242" + - compatible: should be "adi,adf7242", "adi,adf7241" - spi-max-frequency: maximal bus speed (12.5 MHz) - reg: the chipselect index - interrupts: the interrupt generated by the device via pin IRQ1. diff --git a/Documentation/devicetree/bindings/net/mdio.txt b/Documentation/devicetree/bindings/net/mdio.txt index 96a53f89aa6e..e3e1603f256c 100644 --- a/Documentation/devicetree/bindings/net/mdio.txt +++ b/Documentation/devicetree/bindings/net/mdio.txt @@ -18,7 +18,7 @@ Example : This example shows these optional properties, plus other properties required for the TI Davinci MDIO driver. - davinci_mdio: ethernet@0x5c030000 { + davinci_mdio: ethernet@5c030000 { compatible = "ti,davinci_mdio"; reg = <0x5c030000 0x1000>; #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 214eaa9a6683..53c13ee384a4 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -28,7 +28,7 @@ Required properties: - mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup which is required for those SoCs equipped with SGMII such as MT7622 SoC. - mediatek,pctl: phandle to the syscon node that handles the ports slew rate - and driver current + and driver current: only for MT2701 and MT7623 SoC Optional properties: - interrupt-parent: Should be the phandle for the interrupt controller diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 77d0b2a61ffa..d2169a56f5e3 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -53,6 +53,14 @@ Optional Properties: to ensure the integrated PHY is used. The absence of this property indicates the muxers should be configured so that the external PHY is used. +- reset-gpios: The GPIO phandle and specifier for the PHY reset signal. + +- reset-assert-us: Delay after the reset was asserted in microseconds. + If this property is missing the delay will be skipped. + +- reset-deassert-us: Delay after the reset was deasserted in microseconds. + If this property is missing the delay will be skipped. + Example: ethernet-phy@0 { @@ -60,4 +68,8 @@ ethernet-phy@0 { interrupt-parent = <&PIC>; interrupts = <35 IRQ_TYPE_EDGE_RISING>; reg = <0>; + + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <2000>; }; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt index 60e970ce10ee..f1c441bedf68 100644 --- a/Documentation/devicetree/bindings/net/sff,sfp.txt +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -3,7 +3,9 @@ Transceiver Required properties: -- compatible : must be "sff,sfp" +- compatible : must be one of + "sff,sfp" for SFP modules + "sff,sff" for soldered down SFF modules Optional Properties: @@ -11,7 +13,8 @@ Optional Properties: interface - mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) - module presence input gpio signal, active (module absent) high + module presence input gpio signal, active (module absent) high. Must + not be present for SFF modules - los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal Indication input gpio signal, active (signal lost) high @@ -24,10 +27,11 @@ Optional Properties: - rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate + Must not be present for SFF modules - rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: - high Tx rate + high Tx rate. Must not be present for SFF modules Example #1: Direct serdes to SFP connection diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index b30d04b54ee9..17d6819669c8 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -28,7 +28,7 @@ Required properties: Example: -gmii_to_sgmii_converter: phy@0x100000240 { +gmii_to_sgmii_converter: phy@100000240 { compatible = "altr,gmii-to-sgmii-2.0"; reg = <0x00000001 0x00000240 0x00000008>, <0x00000001 0x00000200 0x00000040>; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt new file mode 100644 index 000000000000..270ea4efff13 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt @@ -0,0 +1,48 @@ +* Socionext AVE ethernet controller + +This describes the devicetree bindings for AVE ethernet controller +implemented on Socionext UniPhier SoCs. + +Required properties: + - compatible: Should be + - "socionext,uniphier-pro4-ave4" : for Pro4 SoC + - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC + - "socionext,uniphier-ld11-ave4" : for LD11 SoC + - "socionext,uniphier-ld20-ave4" : for LD20 SoC + - reg: Address where registers are mapped and size of region. + - interrupts: Should contain the MAC interrupt. + - phy-mode: See ethernet.txt in the same directory. Allow to choose + "rgmii", "rmii", or "mii" according to the PHY. + - phy-handle: Should point to the external phy device. + See ethernet.txt file in the same directory. + - clocks: A phandle to the clock for the MAC. + +Optional properties: + - resets: A phandle to the reset control for the MAC. + - local-mac-address: See ethernet.txt in the same directory. + +Required subnode: + - mdio: A container for child nodes representing phy nodes. + See phy.txt in the same directory. + +Example: + + ether: ethernet@65000000 { + compatible = "socionext,uniphier-ld20-ave4"; + reg = <0x65000000 0x8500>; + interrupts = <0 66 4>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + clocks = <&sys_clk 6>; + resets = <&sys_rst 6>; + local-mac-address = [00 00 00 00 00 00]; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethphy@1 { + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt new file mode 100644 index 000000000000..0cff94fb0433 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt @@ -0,0 +1,53 @@ +* Socionext NetSec Ethernet Controller IP + +Required properties: +- compatible: Should be "socionext,synquacer-netsec" +- reg: Address and length of the control register area, followed by the + address and length of the EEPROM holding the MAC address and + microengine firmware +- interrupts: Should contain ethernet controller interrupt +- clocks: phandle to the PHY reference clock +- clock-names: Should be "phy_ref_clk" +- phy-mode: See ethernet.txt file in the same directory +- phy-handle: See ethernet.txt in the same directory. + +- mdio device tree subnode: When the Netsec has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + - compatible: Refer to phy.txt + - reg: phy id used to communicate to phy. + +Optional properties: (See ethernet.txt file in the same directory) +- dma-coherent: Boolean property, must only be present if memory + accesses performed by the device are cache coherent. +- local-mac-address: See ethernet.txt in the same directory. +- mac-address: See ethernet.txt in the same directory. +- max-speed: See ethernet.txt in the same directory. +- max-frame-size: See ethernet.txt in the same directory. + +Example: + eth0: ethernet@522d0000 { + compatible = "socionext,synquacer-netsec"; + reg = <0 0x522d0000 0x0 0x10000>, <0 0x10000000 0x0 0x10000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_netsec>; + clock-names = "phy_ref_clk"; + phy-mode = "rgmii"; + max-speed = <1000>; + max-frame-size = <9000>; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,wilink-st.txt b/Documentation/devicetree/bindings/net/ti-bluetooth.txt index 1649c1f66b07..6d03ff8c7068 100644 --- a/Documentation/devicetree/bindings/net/ti,wilink-st.txt +++ b/Documentation/devicetree/bindings/net/ti-bluetooth.txt @@ -1,10 +1,18 @@ -TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices +Texas Instruments Bluetooth Chips +--------------------------------- + +This documents the binding structure and common properties for serial +attached TI Bluetooth devices. The following chips are included in this +binding: + +* TI CC256x Bluetooth devices +* TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices TI WiLink devices have a UART interface for providing Bluetooth, FM radio, and GPS over what's called "shared transport". The shared transport is standard BT HCI protocol with additional channels for the other functions. -These devices also have a separate WiFi interface as described in +TI WiLink devices also have a separate WiFi interface as described in wireless/ti,wlcore.txt. This bindings follows the UART slave device binding in @@ -12,6 +20,7 @@ This bindings follows the UART slave device binding in Required properties: - compatible: should be one of the following: + "ti,cc2560" "ti,wl1271-st" "ti,wl1273-st" "ti,wl1281-st" @@ -32,6 +41,9 @@ Optional properties: See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entry: "ext_clock" (External clock provided to the TI combo chip). + - nvmem-cells: phandle to nvmem data cell that contains a 6 byte BD address + with the most significant byte first (big-endian). + - nvmem-cell-names: "bd-address" (required when nvmem-cells is specified) Example: @@ -43,5 +55,7 @@ Example: enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; clocks = <&clk32k_wl18xx>; clock-names = "ext_clock"; + nvmem-cells = <&bd_address>; + nvmem-cell-names = "bd-address"; }; }; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt new file mode 100644 index 000000000000..0c17a0ec9b7b --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -0,0 +1,32 @@ +* MediaTek mt76xx devices + +This node provides properties for configuring the MediaTek mt76xx wireless +device. The node is expected to be specified as a child node of the PCI +controller to which the wireless chip is connected. + +Optional properties: + +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory +- ieee80211-freq-limit: See ieee80211.txt +- mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data + +Optional nodes: +- led: Properties for a connected LED + Optional properties: + - led-sources: See Documentation/devicetree/bindings/leds/common.txt + +&pcie { + pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + mediatek,mtd-eeprom = <&factory 0x8000>; + + led { + led-sources = <2>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 74d7f0af209c..3d2a031217da 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -41,6 +41,9 @@ Optional properties: - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into MSI address register. +- qcom,ath10k-calibration-variant: string to search for in the board-2.bin + variant list with the same bus and device + specific ids - qcom,ath10k-calibration-data : calibration data + board specific data as an array, the length can vary between hw versions. diff --git a/Documentation/devicetree/bindings/nios2/nios2.txt b/Documentation/devicetree/bindings/nios2/nios2.txt index d6d0a94cb3bb..b95e831bcba3 100644 --- a/Documentation/devicetree/bindings/nios2/nios2.txt +++ b/Documentation/devicetree/bindings/nios2/nios2.txt @@ -36,7 +36,7 @@ Optional properties: Example: -cpu@0x0 { +cpu@0 { device_type = "cpu"; compatible = "altr,nios2-1.0"; reg = <0>; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 9d733af26be7..4e4f30288c8b 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -45,6 +45,11 @@ Devices supporting OPPs must set their "operating-points-v2" property with phandle to a OPP table in their DT node. The OPP core will use this phandle to find the operating points for the device. +This can contain more than one phandle for power domain providers that provide +multiple power domains. That is, one phandle for each power domain. If only one +phandle is available, then the same OPP table will be used for all power domains +provided by the power domain provider. + If required, this can be extended for SoC vendor specific bindings. Such bindings should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt and should have a compatible description like: "operating-points-v2-<vendor>". @@ -154,6 +159,14 @@ Optional properties: - status: Marks the node enabled/disabled. +- required-opp: This contains phandle to an OPP node in another device's OPP + table. It may contain an array of phandles, where each phandle points to an + OPP of a different device. It should not contain multiple phandles to the OPP + nodes in the same OPP table. This specifies the minimum required OPP of the + device(s), whose OPP's phandle is present in this property, for the + functioning of the current device at the current OPP (where this property is + present). + Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. / { diff --git a/Documentation/devicetree/bindings/opp/ti-omap5-opp-supply.txt b/Documentation/devicetree/bindings/opp/ti-omap5-opp-supply.txt new file mode 100644 index 000000000000..832346e489a3 --- /dev/null +++ b/Documentation/devicetree/bindings/opp/ti-omap5-opp-supply.txt @@ -0,0 +1,63 @@ +Texas Instruments OMAP compatible OPP supply description + +OMAP5, DRA7, and AM57 family of SoCs have Class0 AVS eFuse registers which +contain data that can be used to adjust voltages programmed for some of their +supplies for more efficient operation. This binding provides the information +needed to read these values and use them to program the main regulator during +an OPP transitions. + +Also, some supplies may have an associated vbb-supply which is an Adaptive Body +Bias regulator which much be transitioned in a specific sequence with regards +to the vdd-supply and clk when making an OPP transition. By supplying two +regulators to the device that will undergo OPP transitions we can make use +of the multi regulator binding that is part of the OPP core described here [1] +to describe both regulators needed by the platform. + +[1] Documentation/devicetree/bindings/opp/opp.txt + +Required Properties for Device Node: +- vdd-supply: phandle to regulator controlling VDD supply +- vbb-supply: phandle to regulator controlling Body Bias supply + (Usually Adaptive Body Bias regulator) + +Required Properties for opp-supply node: +- compatible: Should be one of: + "ti,omap-opp-supply" - basic OPP supply controlling VDD and VBB + "ti,omap5-opp-supply" - OMAP5+ optimized voltages in efuse(class0)VDD + along with VBB + "ti,omap5-core-opp-supply" - OMAP5+ optimized voltages in efuse(class0) VDD + but no VBB. +- reg: Address and length of the efuse register set for the device (mandatory + only for "ti,omap5-opp-supply") +- ti,efuse-settings: An array of u32 tuple items providing information about + optimized efuse configuration. Each item consists of the following: + volt: voltage in uV - reference voltage (OPP voltage) + efuse_offseet: efuse offset from reg where the optimized voltage is stored. +- ti,absolute-max-voltage-uv: absolute maximum voltage for the OPP supply. + +Example: + +/* Device Node (CPU) */ +cpus { + cpu0: cpu@0 { + device_type = "cpu"; + + ... + + vdd-supply = <&vcc>; + vbb-supply = <&abb_mpu>; + }; +}; + +/* OMAP OPP Supply with Class0 registers */ +opp_supply_mpu: opp_supply@4a003b20 { + compatible = "ti,omap5-opp-supply"; + reg = <0x4a003b20 0x8>; + ti,efuse-settings = < + /* uV offset */ + 1060000 0x0 + 1160000 0x4 + 1210000 0x8 + >; + ti,absolute-max-voltage-uv = <1500000>; +}; diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt index 495880193adc..a1dc9366a8fc 100644 --- a/Documentation/devicetree/bindings/pci/altera-pcie.txt +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -25,7 +25,7 @@ Optional properties: - bus-range: PCI bus numbers covered Example - pcie_0: pcie@0xc00000000 { + pcie_0: pcie@c00000000 { compatible = "altr,pcie-root-port-1.0"; reg = <0xc0000000 0x20000000>, <0xff220000 0x00004000>; diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt index 4e4aee4439ea..979dc7b6cfe8 100644 --- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -4,7 +4,10 @@ This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "axis,artpec6-pcie", "snps,dw-pcie" +- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode; + "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode; + "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode; + "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode; - reg: base addresses and lengths of the PCIe controller (DBI), the PHY controller, and configuration address space. - reg-names: Must include the following entries: diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 7b1e48bf172b..cb33421184a0 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -41,6 +41,7 @@ Optional properties: Additional required properties for imx6sx-pcie: - clock names: Must include the following additional entries: - "pcie_inbound_axi" +- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain Additional required properties for imx7d-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain @@ -52,7 +53,7 @@ Additional required properties for imx7d-pcie: Example: - pcie@0x01000000 { + pcie@01000000 { compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; reg = <0x01ffc000 0x04000>, <0x01f00000 0x80000>; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index bdb7ab39d2d7..7bf9df047a1e 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -21,7 +21,7 @@ Optional properties: - dma-coherent: Present if DMA operations are coherent. Hip05 Example (note that Hip06 is the same except compatible): - pcie@0xb0080000 { + pcie@b0080000 { compatible = "hisilicon,hip05-pcie", "snps,dw-pcie"; reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>; reg-names = "rc_dbi", "config"; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt index 34a11bfbfb60..651d957d1051 100644 --- a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -6,9 +6,6 @@ and thus inherits all the common properties defined in designware-pcie.txt. Required properties: - compatible: "samsung,exynos5440-pcie" - reg: base addresses and lengths of the PCIe controller, - the PHY controller, additional register for the PHY controller. - (Registers for the PHY controller are DEPRECATED. - Use the PHY framework.) - reg-names : First name should be set to "elbi". And use the "config" instead of getting the configuration address space from "ranges". @@ -23,49 +20,8 @@ For other common properties, refer to Example: -SoC-specific DT Entry: +SoC-specific DT Entry (with using PHY framework): - pcie@290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000 - 0x270000 0x1000 - 0x271000 0x40>; - interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - num-lanes = <4>; - }; - - pcie@2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000 - 0x272000 0x1000 - 0x271040 0x40>; - interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; - num-lanes = <4>; - }; - -With using PHY framework: pcie_phy0: pcie-phy@270000 { ... reg = <0x270000 0x1000>, <0x271000 0x40>; @@ -74,13 +30,21 @@ With using PHY framework: }; pcie@290000 { - ... + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; reg = <0x290000 0x1000>, <0x40000000 0x1000>; reg-names = "elbi", "config"; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; phys = <&pcie_phy0>; ranges = <0x81000000 0 0 0x60001000 0 0x00010000 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; - ... + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; }; Board-specific DT Entry: diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index cbc7847dbf6c..c1ce5a0a652e 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -45,7 +45,7 @@ Optional properties: - usb3_vbus-supply : regulator phandle for controller usb3 vbus Example: - usbphy: phy@0x01c13400 { + usbphy: phy@01c13400 { #phy-cells = <1>; compatible = "allwinner,sun4i-a10-usb-phy"; /* phy base regs, phy1 pmu reg, phy2 pmu reg */ diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index cd13e6157088..57dfda8a7a1d 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -120,7 +120,7 @@ usb3phy@4a084400 { "refclk"; }; -sata_phy: phy@4A096000 { +sata_phy: phy@4a096000 { compatible = "ti,phy-pipe3-sata"; reg = <0x4A096000 0x80>, /* phy_rx */ <0x4A096400 0x64>, /* phy_tx */ diff --git a/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt b/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt index 2c11866221c2..c591b9cb5ba0 100644 --- a/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt +++ b/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt @@ -49,7 +49,7 @@ explained in Documentation/devicetree/bindings/gpio/gpio.txt. Example ------- -iomux: iomux@FF10601c { +iomux: iomux@ff10601c { compatible = "abilis,tb10x-iomux"; reg = <0xFF10601c 0x4>; pctl_gpio_a: pctl-gpio-a { @@ -59,7 +59,7 @@ iomux: iomux@FF10601c { abilis,function = "uart0"; }; }; -uart@FF100000 { +uart@ff100000 { compatible = "snps,dw-apb-uart"; reg = <0xFF100000 0x100>; clock-frequency = <166666666>; @@ -69,7 +69,7 @@ uart@FF100000 { pinctrl-names = "default"; pinctrl-0 = <&pctl_uart0>; }; -gpioa: gpio@FF140000 { +gpioa: gpio@ff140000 { compatible = "abilis,tb10x-gpio"; reg = <0xFF140000 0x1000>; gpio-controller; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt index 3600d5c6c4d7..3914529a3214 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt @@ -25,7 +25,7 @@ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt For example: - pinmux: pinmux@0x0301d0c8 { + pinmux: pinmux@0301d0c8 { compatible = "brcm,cygnus-pinmux"; reg = <0x0301d0c8 0x1b0>; diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt index 0326154c7925..a72dc3178179 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -152,7 +152,7 @@ resetn Example: -------- -pinctrl@18101C00 { +pinctrl@18101c00 { compatible = "img,pistachio-system-pinctrl"; reg = <0x18101C00 0x400>; diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt index 8e5216bcd748..4658f105fa09 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt @@ -163,7 +163,7 @@ Valid values for xRX300 pin names: io42-io43,io48-io61. Example: - gpio: pinmux@E100B10 { + gpio: pinmux@e100b10 { compatible = "lantiq,danube-pinctrl"; pinctrl-names = "default"; pinctrl-0 = <&state_default>; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 2392557ede27..2c12f9789116 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -9,6 +9,8 @@ Required properties for the root node: "amlogic,meson-gxbb-aobus-pinctrl" "amlogic,meson-gxl-periphs-pinctrl" "amlogic,meson-gxl-aobus-pinctrl" + "amlogic,meson-axg-periphs-pinctrl" + "amlogic,meson-axg-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-atlas7.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-atlas7.txt index eecf028ff485..bf9b07016c87 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-atlas7.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-atlas7.txt @@ -96,14 +96,14 @@ For example, pinctrl might have subnodes like the following: For a specific board, if it wants to use sd1, it can add the following to its board-specific .dts file. -sd1: sd@0x12340000 { +sd1: sd@12340000 { pinctrl-names = "default"; pinctrl-0 = <&sd1_pmx0>; } or -sd1: sd@0x12340000 { +sd1: sd@12340000 { pinctrl-names = "default"; pinctrl-0 = <&sd1_pmx1>; } diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 231fa1db7c5e..afa8a18ea11a 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -81,7 +81,7 @@ Examples: reg = <0 0x10005000 0 0x1000>; }; - syscfg_pctl_b: syscfg_pctl_b@1020C020 { + syscfg_pctl_b: syscfg_pctl_b@1020c020 { compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon"; reg = <0 0x1020C020 0 0x1000>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt index 5f55be59d914..f8420520e14b 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -41,7 +41,7 @@ For example, pinctrl might have subnodes like the following: For a specific board, if it wants to use uart2 without hardware flow control, it can add the following to its board-specific .dts file. -uart2: uart@0xb0070000 { +uart2: uart@b0070000 { pinctrl-names = "default"; pinctrl-0 = <&uart2_noflow_pins_a>; } diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 4864e3a74de3..a01a3b8a2363 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -136,7 +136,7 @@ Example for rk3188: #size-cells = <1>; ranges; - gpio0: gpio0@0x2000a000 { + gpio0: gpio0@2000a000 { compatible = "rockchip,rk3188-gpio-bank0"; reg = <0x2000a000 0x100>; interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; @@ -149,7 +149,7 @@ Example for rk3188: #interrupt-cells = <2>; }; - gpio1: gpio1@0x2003c000 { + gpio1: gpio1@2003c000 { compatible = "rockchip,gpio-bank"; reg = <0x2003c000 0x100>; interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/power/actions,owl-sps.txt b/Documentation/devicetree/bindings/power/actions,owl-sps.txt index 007b9a7ae723..78edd63641e8 100644 --- a/Documentation/devicetree/bindings/power/actions,owl-sps.txt +++ b/Documentation/devicetree/bindings/power/actions,owl-sps.txt @@ -2,10 +2,12 @@ Actions Semi Owl Smart Power System (SPS) Required properties: - compatible : "actions,s500-sps" for S500 + "actions,s700-sps" for S700 - reg : Offset and length of the register set for the device. - #power-domain-cells : Must be 1. See macros in: include/dt-bindings/power/owl-s500-powergate.h for S500 + include/dt-bindings/power/owl-s700-powergate.h for S700 Example: diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt index e371b262d709..b31d6bbeee16 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt @@ -9,6 +9,7 @@ Required properties: - fsl,imx6q-gpc - fsl,imx6qp-gpc - fsl,imx6sl-gpc + - fsl,imx6sx-gpc - reg: should be register base and length as documented in the datasheet - interrupts: Should contain one interrupt specifier for the GPC interrupt @@ -29,6 +30,8 @@ Required properties: PU_DOMAIN 1 The following additional DOMAIN_INDEX value is valid for i.MX6SL: DISPLAY_DOMAIN 2 + The following additional DOMAIN_INDEX value is valid for i.MX6SX: + PCI_DOMAIN 3 - #power-domain-cells: Should be 0 diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt index 02f45c65fd87..9acce75b29ab 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt @@ -44,10 +44,10 @@ Example: #address-cells = <1>; #size-cells = <0>; - pgc_pcie_phy: power-domain@3 { + pgc_pcie_phy: power-domain@1 { #power-domain-cells = <0>; - reg = <IMX7_POWER_DOMAIN_PCIE_PHY>; + reg = <1>; power-supply = <®_1p0d>; }; }; diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 14bd9e945ff6..f3355313c020 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -40,6 +40,12 @@ Optional properties: domain's idle states. In the absence of this property, the domain would be considered as capable of being powered-on or powered-off. +- operating-points-v2 : Phandles to the OPP tables of power domains provided by + a power domain provider. If the provider provides a single power domain only + or all the power domains provided by the provider have identical OPP tables, + then this shall contain a single phandle. Refer to ../opp/opp.txt for more + information. + Example: power: power-controller@12340000 { @@ -120,4 +126,63 @@ The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". +Optional properties: +- required-opp: This contains phandle to an OPP node in another device's OPP + table. It may contain an array of phandles, where each phandle points to an + OPP of a different device. It should not contain multiple phandles to the OPP + nodes in the same OPP table. This specifies the minimum required OPP of the + device(s), whose OPP's phandle is present in this property, for the + functioning of the current device at the current OPP (where this property is + present). + +Example: +- OPP table for domain provider that provides two domains. + + domain0_opp_table: opp-table0 { + compatible = "operating-points-v2"; + + domain0_opp_0: opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain0_opp_1: opp-1100000000 { + opp-hz = /bits/ 64 <1100000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + domain1_opp_table: opp-table1 { + compatible = "operating-points-v2"; + + domain1_opp_0: opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain1_opp_1: opp-1300000000 { + opp-hz = /bits/ 64 <1300000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + power: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + operating-points-v2 = <&domain0_opp_table>, <&domain1_opp_table>; + }; + + leaky-device0@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 0>; + required-opp = <&domain0_opp_0>; + }; + + leaky-device1@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 1>; + required-opp = <&domain1_opp_1>; + }; + [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt deleted file mode 100644 index 1b81fcd9fb72..000000000000 --- a/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt +++ /dev/null @@ -1,23 +0,0 @@ -i.mx6 Poweroff Driver - -SNVS_LPCR in SNVS module can power off the whole system by pull -PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. -If you don't want to use PMIC_ON_REQ as power on/off control, -please set status='disabled' to disable this driver. - -Required Properties: --compatible: "fsl,sec-v4.0-poweroff" --reg: Specifies the physical address of the SNVS_LPCR register - -Example: - snvs@20cc000 { - compatible = "fsl,sec-v4.0-mon", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x020cc000 0x4000>; - ..... - snvs_poweroff: snvs-poweroff@38 { - compatible = "fsl,sec-v4.0-poweroff"; - reg = <0x38 0x4>; - }; - } diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index 6858e1a804ad..615c1cb6889f 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -15,6 +15,7 @@ Required properties: * "ti,bq27520g2" - BQ27520-g2 * "ti,bq27520g3" - BQ27520-g3 * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27521" - BQ27521 * "ti,bq27530" - BQ27530 * "ti,bq27531" - BQ27531 * "ti,bq27541" - BQ27541 diff --git a/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt b/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt index 641bc13983e1..ed6a414b2e10 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt @@ -223,37 +223,37 @@ lac-portals { reg = <0x9000 0x1000>; }; - lportal10: lac-portal@A000 { + lportal10: lac-portal@a000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x20E>; reg = <0xA000 0x1000>; }; - lportal11: lac-portal@B000 { + lportal11: lac-portal@b000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x20F>; reg = <0xB000 0x1000>; }; - lportal12: lac-portal@C000 { + lportal12: lac-portal@c000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x210>; reg = <0xC000 0x1000>; }; - lportal13: lac-portal@D000 { + lportal13: lac-portal@d000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x211>; reg = <0xD000 0x1000>; }; - lportal14: lac-portal@E000 { + lportal14: lac-portal@e000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x212>; reg = <0xE000 0x1000>; }; - lportal15: lac-portal@F000 { + lportal15: lac-portal@f000 { compatible = "fsl,interlaken-lac-portal-v1.0"; fsl,liodn = <0x213>; reg = <0xF000 0x1000>; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 378f6dc8b8bd..6b8719fc9b81 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -42,8 +42,15 @@ Optional properties: - regulator-state-[mem/disk] node has following common properties: - regulator-on-in-suspend: regulator should be on in suspend state. - regulator-off-in-suspend: regulator should be off in suspend state. - - regulator-suspend-microvolt: regulator should be set to this voltage - in suspend. + - regulator-suspend-min-microvolt: minimum voltage may be set in + suspend state. + - regulator-suspend-max-microvolt: maximum voltage may be set in + suspend state. + - regulator-suspend-microvolt: the default voltage which regulator + should be set in suspend, this can be adjusted among + <regulator-suspend-min-microvolt, regulator-suspend-max-microvolt> + - regulator-changeable-in-suspend: whether the default voltage and + the regulator on/off in suspend can be changed in runtime. - regulator-mode: operating mode in the given suspend state. The set of possible operating modes depends on the capabilities of every hardware so the valid modes are documented on each regulator @@ -107,7 +114,7 @@ regulators (twl_reg1 and twl_reg2), ... }; - mmc: mmc@0x0 { + mmc: mmc@0 { ... ... vmmc-supply = <&twl_reg1>; diff --git a/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt new file mode 100644 index 000000000000..63dc07877cd6 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt @@ -0,0 +1,43 @@ +Spreadtrum SC2731 Voltage regulators + +The SC2731 integrates low-voltage and low quiescent current DCDC/LDO. +14 LDO and 3 DCDCs are designed for external use. All DCDCs/LDOs have +their own bypass (power-down) control signals. External tantalum or MLCC +ceramic capacitors are recommended to use with these LDOs. + +Required properties: + - compatible: should be "sprd,sc27xx-regulator". + +List of regulators provided by this controller. It is named according to +its regulator type, BUCK_<name> and LDO_<name>. The definition for each +of these nodes is defined using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + BUCK_CPU0, BUCK_CPU1, BUCK_RF +LDO: + LDO_CAMA0, LDO_CAMA1, LDO_CAMMOT, LDO_VLDO, LDO_EMMCCORE, LDO_SDCORE, + LDO_SDIO, LDO_WIFIPA, LDO_USB33, LDO_CAMD0, LDO_CAMD1, LDO_CON, + LDO_CAMIO, LDO_SRAM + +Example: + regulators { + compatible = "sprd,sc27xx-regulator"; + + vddarm0: BUCK_CPU0 { + regulator-name = "vddarm0"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1996875>; + regulator-ramp-delay = <25000>; + regulator-always-on; + }; + + vddcama0: LDO_CAMA0 { + regulator-name = "vddcama0"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + regulator-enable-ramp-delay = <100>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt index 3944ee3e731e..5ddb8500a929 100644 --- a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt +++ b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt @@ -10,7 +10,7 @@ Required properties: - clocks: Must contain an entry for peripheral clock. Example: - vrefbuf: regulator@58003C00 { + vrefbuf: regulator@58003c00 { compatible = "st,stm32-vrefbuf"; reg = <0x58003C00 0x8>; clocks = <&rcc VREF_CK>; diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt index e746b631793a..28ef6c295c76 100644 --- a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt +++ b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt @@ -5,7 +5,8 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "amlogic,meson8b-reset" or "amlogic,meson-gxbb-reset" +- compatible: Should be "amlogic,meson8b-reset", "amlogic,meson-gxbb-reset" or + "amlogic,meson-axg-reset". - reg: should contain the register address base - #reset-cells: 1, see below diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt index 26542690b578..627b29531a32 100644 --- a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt @@ -1,11 +1,19 @@ -BCM2835 Random number generator +BCM2835/6368 Random number generator Required properties: -- compatible : should be "brcm,bcm2835-rng" or "brcm,bcm-nsp-rng" or - "brcm,bcm5301x-rng" +- compatible : should be one of + "brcm,bcm2835-rng" + "brcm,bcm-nsp-rng" + "brcm,bcm5301x-rng" or + "brcm,bcm6368-rng" - reg : Specifies base physical address and size of the registers. +Optional properties: + +- clocks : phandle to clock-controller plus clock-specifier pair +- clock-names : "ipsec" as a clock name + Example: rng { @@ -17,3 +25,11 @@ rng@18033000 { compatible = "brcm,bcm-nsp-rng"; reg = <0x18033000 0x14>; }; + +random: rng@10004180 { + compatible = "brcm,bcm6368-rng"; + reg = <0x10004180 0x14>; + + clocks = <&periph_clk 18>; + clock-names = "ipsec"; +}; diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt b/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt deleted file mode 100644 index 4b5ac600bfbd..000000000000 --- a/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt +++ /dev/null @@ -1,17 +0,0 @@ -BCM6368 Random number generator - -Required properties: - -- compatible : should be "brcm,bcm6368-rng" -- reg : Specifies base physical address and size of the registers -- clocks : phandle to clock-controller plus clock-specifier pair -- clock-names : "ipsec" as a clock name - -Example: - random: rng@10004180 { - compatible = "brcm,bcm6368-rng"; - reg = <0x10004180 0x14>; - - clocks = <&periph_clk 18>; - clock-names = "ipsec"; - }; diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt index 8adbab268ca3..4f8d8fde0c1c 100644 --- a/Documentation/devicetree/bindings/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt @@ -12,7 +12,7 @@ Optional properties: Example: -uart@0x4000c400 { +uart@4000c400 { compatible = "energymicro,efm32-uart"; reg = <0x4000c400 0x400>; interrupts = <15>; diff --git a/Documentation/devicetree/bindings/serial/lantiq_asc.txt b/Documentation/devicetree/bindings/serial/lantiq_asc.txt index 5b78591aaa46..3acbd309ab9d 100644 --- a/Documentation/devicetree/bindings/serial/lantiq_asc.txt +++ b/Documentation/devicetree/bindings/serial/lantiq_asc.txt @@ -8,7 +8,7 @@ Required properties: Example: -asc1: serial@E100C00 { +asc1: serial@e100c00 { compatible = "lantiq,asc"; reg = <0xE100C00 0x400>; interrupt-parent = <&icu0>; diff --git a/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt index f311472990a7..75996b6111bb 100644 --- a/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt +++ b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt @@ -14,7 +14,7 @@ Required properties: Example: - ps20: ps2@0x01c2a000 { + ps20: ps2@01c2a000 { compatible = "allwinner,sun4i-a10-ps2"; reg = <0x01c2a000 0x400>; interrupts = <0 62 4>; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index 40056f7990f8..76bf45b893fa 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -12,11 +12,13 @@ power/power_domain.txt. It provides the power domains defined in - include/dt-bindings/power/mt8173-power.h - include/dt-bindings/power/mt6797-power.h - include/dt-bindings/power/mt2701-power.h +- include/dt-bindings/power/mt2712-power.h - include/dt-bindings/power/mt7622-power.h Required properties: - compatible: Should be one of: - "mediatek,mt2701-scpsys" + - "mediatek,mt2712-scpsys" - "mediatek,mt6797-scpsys" - "mediatek,mt7622-scpsys" - "mediatek,mt8173-scpsys" @@ -27,6 +29,7 @@ Required properties: These are clocks which hardware needs to be enabled before enabling certain power domains. Required clocks for MT2701: "mm", "mfg", "ethif" + Required clocks for MT2712: "mm", "mfg", "venc", "jpgdec", "audio", "vdec" Required clocks for MT6797: "mm", "mfg", "vdec" Required clocks for MT7622: "hif_sel" Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt index af9ca37221ce..a35af2dafdad 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -17,9 +17,15 @@ processor ID) and a string identifier. Value type: <prop-encoded-array> Definition: one entry specifying the smp2p notification interrupt -- qcom,ipc: +- mboxes: Usage: required Value type: <prop-encoded-array> + Definition: reference to the associated doorbell in APCS, as described + in mailbox/mailbox.txt + +- qcom,ipc: + Usage: required, unless mboxes is specified + Value type: <prop-encoded-array> Definition: three entries specifying the outgoing ipc bit used for signaling the remote end of the smp2p edge: - phandle to a syscon node representing the apcs registers diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt index 64c66a5644e7..77cd42cc5f54 100644 --- a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -220,7 +220,7 @@ qmss: qmss@2a40000 { #address-cells = <1>; #size-cells = <1>; ranges; - pdsp0@0x2a10000 { + pdsp0@2a10000 { reg = <0x2a10000 0x1000>, <0x2a0f000 0x100>, <0x2a0c000 0x3c8>, diff --git a/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt b/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt index 5875ca459ed1..4248b662deff 100644 --- a/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt +++ b/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt @@ -21,7 +21,7 @@ please check: Example: - i2s: i2s@0x77600000 { + i2s: i2s@77600000 { compatible = "adi,axi-i2s-1.00.a"; reg = <0x77600000 0x1000>; clocks = <&clk 15>, <&audio_clock>; diff --git a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt index 4eb7997674a0..7b664e7cb4ae 100644 --- a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt +++ b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt @@ -20,7 +20,7 @@ please check: Example: - spdif: spdif@0x77400000 { + spdif: spdif@77400000 { compatible = "adi,axi-spdif-tx-1.00.a"; reg = <0x77600000 0x1000>; clocks = <&clk 15>, <&audio_clock>; diff --git a/Documentation/devicetree/bindings/sound/ak4613.txt b/Documentation/devicetree/bindings/sound/ak4613.txt index 1783f9ef0930..49a2e74fd9cb 100644 --- a/Documentation/devicetree/bindings/sound/ak4613.txt +++ b/Documentation/devicetree/bindings/sound/ak4613.txt @@ -20,7 +20,7 @@ Optional properties: Example: &i2c { - ak4613: ak4613@0x10 { + ak4613: ak4613@10 { compatible = "asahi-kasei,ak4613"; reg = <0x10>; }; diff --git a/Documentation/devicetree/bindings/sound/ak4642.txt b/Documentation/devicetree/bindings/sound/ak4642.txt index 340784db6808..58e48ee97175 100644 --- a/Documentation/devicetree/bindings/sound/ak4642.txt +++ b/Documentation/devicetree/bindings/sound/ak4642.txt @@ -17,7 +17,7 @@ Optional properties: Example 1: &i2c { - ak4648: ak4648@0x12 { + ak4648: ak4648@12 { compatible = "asahi-kasei,ak4642"; reg = <0x12>; }; diff --git a/Documentation/devicetree/bindings/sound/da7218.txt b/Documentation/devicetree/bindings/sound/da7218.txt index 5ca5a709b6aa..3ab9dfef38d1 100644 --- a/Documentation/devicetree/bindings/sound/da7218.txt +++ b/Documentation/devicetree/bindings/sound/da7218.txt @@ -73,7 +73,7 @@ Example: compatible = "dlg,da7218"; reg = <0x1a>; interrupt-parent = <&gpio6>; - interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; wakeup-source; VDD-supply = <®_audio>; diff --git a/Documentation/devicetree/bindings/sound/da7219.txt b/Documentation/devicetree/bindings/sound/da7219.txt index cf61681826b6..5b54d2d045c3 100644 --- a/Documentation/devicetree/bindings/sound/da7219.txt +++ b/Documentation/devicetree/bindings/sound/da7219.txt @@ -77,7 +77,7 @@ Example: reg = <0x1a>; interrupt-parent = <&gpio6>; - interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; VDD-supply = <®_audio>; VDDMIC-supply = <®_audio>; diff --git a/Documentation/devicetree/bindings/sound/dmic.txt b/Documentation/devicetree/bindings/sound/dmic.txt index 54c8ef6498a8..f7bf65611453 100644 --- a/Documentation/devicetree/bindings/sound/dmic.txt +++ b/Documentation/devicetree/bindings/sound/dmic.txt @@ -7,10 +7,12 @@ Required properties: Optional properties: - dmicen-gpios: GPIO specifier for dmic to control start and stop + - num-channels: Number of microphones on this DAI Example node: dmic_codec: dmic@0 { compatible = "dmic-codec"; dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + num-channels = <1>; }; diff --git a/Documentation/devicetree/bindings/sound/img,i2s-out.txt b/Documentation/devicetree/bindings/sound/img,i2s-out.txt index 0159415b3338..6b0ee9b7e11b 100644 --- a/Documentation/devicetree/bindings/sound/img,i2s-out.txt +++ b/Documentation/devicetree/bindings/sound/img,i2s-out.txt @@ -35,7 +35,7 @@ Optional Properties: Example: -i2s_out: i2s-out@18100A00 { +i2s_out: i2s-out@18100a00 { compatible = "img,i2s-out"; reg = <0x18100A00 0x200>; interrupts = <GIC_SHARED 13 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/img,parallel-out.txt b/Documentation/devicetree/bindings/sound/img,parallel-out.txt index a3015d2a06e0..37a3f94cc126 100644 --- a/Documentation/devicetree/bindings/sound/img,parallel-out.txt +++ b/Documentation/devicetree/bindings/sound/img,parallel-out.txt @@ -29,7 +29,7 @@ Optional Properties: Example: -parallel_out: parallel-out@18100C00 { +parallel_out: parallel-out@18100c00 { compatible = "img,parallel-out"; reg = <0x18100C00 0x100>; interrupts = <GIC_SHARED 19 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-in.txt b/Documentation/devicetree/bindings/sound/img,spdif-in.txt index aab9a81f7e13..f7ea8c87bf34 100644 --- a/Documentation/devicetree/bindings/sound/img,spdif-in.txt +++ b/Documentation/devicetree/bindings/sound/img,spdif-in.txt @@ -29,7 +29,7 @@ Optional Properties: Example: -spdif_in: spdif-in@18100E00 { +spdif_in: spdif-in@18100e00 { compatible = "img,spdif-in"; reg = <0x18100E00 0x100>; interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-out.txt b/Documentation/devicetree/bindings/sound/img,spdif-out.txt index 470a5191e101..413ed8b01870 100644 --- a/Documentation/devicetree/bindings/sound/img,spdif-out.txt +++ b/Documentation/devicetree/bindings/sound/img,spdif-out.txt @@ -29,7 +29,7 @@ Optional Properties: Example: -spdif_out: spdif-out@18100D00 { +spdif_out: spdif-out@18100d00 { compatible = "img,spdif-out"; reg = <0x18100D00 0x100>; interrupts = <GIC_SHARED 21 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/max98371.txt b/Documentation/devicetree/bindings/sound/max98371.txt index 6c285235e64b..8b2b2704b574 100644 --- a/Documentation/devicetree/bindings/sound/max98371.txt +++ b/Documentation/devicetree/bindings/sound/max98371.txt @@ -10,7 +10,7 @@ Required properties: Example: &i2c { - max98371: max98371@0x31 { + max98371: max98371@31 { compatible = "maxim,max98371"; reg = <0x31>; }; diff --git a/Documentation/devicetree/bindings/sound/max98373.txt b/Documentation/devicetree/bindings/sound/max98373.txt new file mode 100644 index 000000000000..456cb1c59353 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98373.txt @@ -0,0 +1,40 @@ +Maxim Integrated MAX98373 Speaker Amplifier + +This device supports I2C. + +Required properties: + + - compatible : "maxim,max98373" + + - reg : the I2C address of the device. + +Optional properties: + + - maxim,vmon-slot-no : slot number used to send voltage information + or in inteleave mode this will be used as + interleave slot. + slot range : 0 ~ 15, Default : 0 + + - maxim,imon-slot-no : slot number used to send current information + slot range : 0 ~ 15, Default : 0 + + - maxim,spkfb-slot-no : slot number used to send speaker feedback information + slot range : 0 ~ 15, Default : 0 + + - maxim,interleave-mode : For cases where a single combined channel + for the I/V sense data is not sufficient, the device can also be configured + to share a single data output channel on alternating frames. + In this configuration, the current and voltage data will be frame interleaved + on a single output channel. + Boolean, define to enable the interleave mode, Default : false + +Example: + +codec: max98373@31 { + compatible = "maxim,max98373"; + reg = <0x31>; + maxim,vmon-slot-no = <0>; + maxim,imon-slot-no = <1>; + maxim,spkfb-slot-no = <2>; + maxim,interleave-mode; +}; diff --git a/Documentation/devicetree/bindings/sound/max9867.txt b/Documentation/devicetree/bindings/sound/max9867.txt index 394cd4eb17ec..b8bd914ee697 100644 --- a/Documentation/devicetree/bindings/sound/max9867.txt +++ b/Documentation/devicetree/bindings/sound/max9867.txt @@ -10,7 +10,7 @@ Required properties: Example: &i2c { - max9867: max9867@0x18 { + max9867: max9867@18 { compatible = "maxim,max9867"; reg = <0x18>; }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt index 77a57f84bed4..6df87b97f7cb 100644 --- a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -2,153 +2,143 @@ Mediatek AFE PCM controller for mt2701 Required properties: - compatible = "mediatek,mt2701-audio"; -- reg: register location and size - interrupts: should contain AFE and ASYS interrupts - interrupt-names: should be "afe" and "asys" - power-domains: should define the power domain +- clocks: Must contain an entry for each entry in clock-names + See ../clocks/clock-bindings.txt for details - clock-names: should have these clock names: "infra_sys_audio_clk", "top_audio_mux1_sel", "top_audio_mux2_sel", - "top_audio_mux1_div", - "top_audio_mux2_div", - "top_audio_48k_timing", - "top_audio_44k_timing", - "top_audpll_mux_sel", - "top_apll_sel", - "top_aud1_pll_98M", - "top_aud2_pll_90M", - "top_hadds2_pll_98M", - "top_hadds2_pll_294M", - "top_audpll", - "top_audpll_d4", - "top_audpll_d8", - "top_audpll_d16", - "top_audpll_d24", - "top_audintbus_sel", - "clk_26m", - "top_syspll1_d4", - "top_aud_k1_src_sel", - "top_aud_k2_src_sel", - "top_aud_k3_src_sel", - "top_aud_k4_src_sel", - "top_aud_k5_src_sel", - "top_aud_k6_src_sel", - "top_aud_k1_src_div", - "top_aud_k2_src_div", - "top_aud_k3_src_div", - "top_aud_k4_src_div", - "top_aud_k5_src_div", - "top_aud_k6_src_div", - "top_aud_i2s1_mclk", - "top_aud_i2s2_mclk", - "top_aud_i2s3_mclk", - "top_aud_i2s4_mclk", - "top_aud_i2s5_mclk", - "top_aud_i2s6_mclk", - "top_asm_m_sel", - "top_asm_h_sel", - "top_univpll2_d4", - "top_univpll2_d2", - "top_syspll_d5"; + "top_audio_a1sys_hp", + "top_audio_a2sys_hp", + "i2s0_src_sel", + "i2s1_src_sel", + "i2s2_src_sel", + "i2s3_src_sel", + "i2s0_src_div", + "i2s1_src_div", + "i2s2_src_div", + "i2s3_src_div", + "i2s0_mclk_en", + "i2s1_mclk_en", + "i2s2_mclk_en", + "i2s3_mclk_en", + "i2so0_hop_ck", + "i2so1_hop_ck", + "i2so2_hop_ck", + "i2so3_hop_ck", + "i2si0_hop_ck", + "i2si1_hop_ck", + "i2si2_hop_ck", + "i2si3_hop_ck", + "asrc0_out_ck", + "asrc1_out_ck", + "asrc2_out_ck", + "asrc3_out_ck", + "audio_afe_pd", + "audio_afe_conn_pd", + "audio_a1sys_pd", + "audio_a2sys_pd", + "audio_mrgif_pd"; +- assigned-clocks: list of input clocks and dividers for the audio system. + See ../clocks/clock-bindings.txt for details. +- assigned-clocks-parents: parent of input clocks of assigned clocks. +- assigned-clock-rates: list of clock frequencies of assigned clocks. + +Must be a subnode of MediaTek audsys device tree node. +See ../arm/mediatek/mediatek,audsys.txt for details about the parent node. Example: - afe: mt2701-afe-pcm@11220000 { - compatible = "mediatek,mt2701-audio"; - reg = <0 0x11220000 0 0x2000>, - <0 0x112A0000 0 0x20000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "afe", "asys"; - power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; - clocks = <&infracfg CLK_INFRA_AUDIO>, - <&topckgen CLK_TOP_AUD_MUX1_SEL>, - <&topckgen CLK_TOP_AUD_MUX2_SEL>, - <&topckgen CLK_TOP_AUD_MUX1_DIV>, - <&topckgen CLK_TOP_AUD_MUX2_DIV>, - <&topckgen CLK_TOP_AUD_48K_TIMING>, - <&topckgen CLK_TOP_AUD_44K_TIMING>, - <&topckgen CLK_TOP_AUDPLL_MUX_SEL>, - <&topckgen CLK_TOP_APLL_SEL>, - <&topckgen CLK_TOP_AUD1PLL_98M>, - <&topckgen CLK_TOP_AUD2PLL_90M>, - <&topckgen CLK_TOP_HADDS2PLL_98M>, - <&topckgen CLK_TOP_HADDS2PLL_294M>, - <&topckgen CLK_TOP_AUDPLL>, - <&topckgen CLK_TOP_AUDPLL_D4>, - <&topckgen CLK_TOP_AUDPLL_D8>, - <&topckgen CLK_TOP_AUDPLL_D16>, - <&topckgen CLK_TOP_AUDPLL_D24>, - <&topckgen CLK_TOP_AUDINTBUS_SEL>, - <&clk26m>, - <&topckgen CLK_TOP_SYSPLL1_D4>, - <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K5_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K6_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K5_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K6_SRC_DIV>, - <&topckgen CLK_TOP_AUD_I2S1_MCLK>, - <&topckgen CLK_TOP_AUD_I2S2_MCLK>, - <&topckgen CLK_TOP_AUD_I2S3_MCLK>, - <&topckgen CLK_TOP_AUD_I2S4_MCLK>, - <&topckgen CLK_TOP_AUD_I2S5_MCLK>, - <&topckgen CLK_TOP_AUD_I2S6_MCLK>, - <&topckgen CLK_TOP_ASM_M_SEL>, - <&topckgen CLK_TOP_ASM_H_SEL>, - <&topckgen CLK_TOP_UNIVPLL2_D4>, - <&topckgen CLK_TOP_UNIVPLL2_D2>, - <&topckgen CLK_TOP_SYSPLL_D5>; + audsys: audio-subsystem@11220000 { + compatible = "mediatek,mt2701-audsys", "syscon", "simple-mfd"; + ... + + afe: audio-controller { + compatible = "mediatek,mt2701-audio"; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "afe", "asys"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; + + clocks = <&infracfg CLK_INFRA_AUDIO>, + <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_48K_TIMING>, + <&topckgen CLK_TOP_AUD_44K_TIMING>, + <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, + <&topckgen CLK_TOP_AUD_I2S1_MCLK>, + <&topckgen CLK_TOP_AUD_I2S2_MCLK>, + <&topckgen CLK_TOP_AUD_I2S3_MCLK>, + <&topckgen CLK_TOP_AUD_I2S4_MCLK>, + <&audsys CLK_AUD_I2SO1>, + <&audsys CLK_AUD_I2SO2>, + <&audsys CLK_AUD_I2SO3>, + <&audsys CLK_AUD_I2SO4>, + <&audsys CLK_AUD_I2SIN1>, + <&audsys CLK_AUD_I2SIN2>, + <&audsys CLK_AUD_I2SIN3>, + <&audsys CLK_AUD_I2SIN4>, + <&audsys CLK_AUD_ASRCO1>, + <&audsys CLK_AUD_ASRCO2>, + <&audsys CLK_AUD_ASRCO3>, + <&audsys CLK_AUD_ASRCO4>, + <&audsys CLK_AUD_AFE>, + <&audsys CLK_AUD_AFE_CONN>, + <&audsys CLK_AUD_A1SYS>, + <&audsys CLK_AUD_A2SYS>, + <&audsys CLK_AUD_AFE_MRGIF>; + + clock-names = "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_a1sys_hp", + "top_audio_a2sys_hp", + "i2s0_src_sel", + "i2s1_src_sel", + "i2s2_src_sel", + "i2s3_src_sel", + "i2s0_src_div", + "i2s1_src_div", + "i2s2_src_div", + "i2s3_src_div", + "i2s0_mclk_en", + "i2s1_mclk_en", + "i2s2_mclk_en", + "i2s3_mclk_en", + "i2so0_hop_ck", + "i2so1_hop_ck", + "i2so2_hop_ck", + "i2so3_hop_ck", + "i2si0_hop_ck", + "i2si1_hop_ck", + "i2si2_hop_ck", + "i2si3_hop_ck", + "asrc0_out_ck", + "asrc1_out_ck", + "asrc2_out_ck", + "asrc3_out_ck", + "audio_afe_pd", + "audio_afe_conn_pd", + "audio_a1sys_pd", + "audio_a2sys_pd", + "audio_mrgif_pd"; - clock-names = "infra_sys_audio_clk", - "top_audio_mux1_sel", - "top_audio_mux2_sel", - "top_audio_mux1_div", - "top_audio_mux2_div", - "top_audio_48k_timing", - "top_audio_44k_timing", - "top_audpll_mux_sel", - "top_apll_sel", - "top_aud1_pll_98M", - "top_aud2_pll_90M", - "top_hadds2_pll_98M", - "top_hadds2_pll_294M", - "top_audpll", - "top_audpll_d4", - "top_audpll_d8", - "top_audpll_d16", - "top_audpll_d24", - "top_audintbus_sel", - "clk_26m", - "top_syspll1_d4", - "top_aud_k1_src_sel", - "top_aud_k2_src_sel", - "top_aud_k3_src_sel", - "top_aud_k4_src_sel", - "top_aud_k5_src_sel", - "top_aud_k6_src_sel", - "top_aud_k1_src_div", - "top_aud_k2_src_div", - "top_aud_k3_src_div", - "top_aud_k4_src_div", - "top_aud_k5_src_div", - "top_aud_k6_src_div", - "top_aud_i2s1_mclk", - "top_aud_i2s2_mclk", - "top_aud_i2s3_mclk", - "top_aud_i2s4_mclk", - "top_aud_i2s5_mclk", - "top_aud_i2s6_mclk", - "top_asm_m_sel", - "top_asm_h_sel", - "top_univpll2_d4", - "top_univpll2_d2", - "top_syspll_d5"; + assigned-clocks = <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_MUX1_DIV>, + <&topckgen CLK_TOP_AUD_MUX2_DIV>; + assigned-clock-parents = <&topckgen CLK_TOP_AUD1PLL_98M>, + <&topckgen CLK_TOP_AUD2PLL_90M>; + assigned-clock-rates = <0>, <0>, <49152000>, <45158400>; + }; }; diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt index 2f5e973285a6..d16d96839bcb 100644 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ b/Documentation/devicetree/bindings/sound/nau8825.txt @@ -69,7 +69,7 @@ Optional properties: - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,crosstalk-bypass: make crosstalk function bypass if set. + - nuvoton,crosstalk-enable: make crosstalk function enable if set. - clocks: list of phandle and clock specifier pairs according to common clock bindings for the clocks described in clock-names @@ -98,7 +98,7 @@ Example: nuvoton,short-key-debounce = <2>; nuvoton,jack-insert-debounce = <7>; nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-bypass; + nuvoton,crosstalk-enable; clock-names = "mclk"; clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>; diff --git a/Documentation/devicetree/bindings/sound/pcm186x.txt b/Documentation/devicetree/bindings/sound/pcm186x.txt new file mode 100644 index 000000000000..1087f4855980 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm186x.txt @@ -0,0 +1,42 @@ +Texas Instruments PCM186x Universal Audio ADC + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "ti,pcm1862", + "ti,pcm1863", + "ti,pcm1864", + "ti,pcm1865" + + - reg : The I2C address of the device for I2C, the chip select + number for SPI. + + - avdd-supply: Analog core power supply (3.3v) + - dvdd-supply: Digital core power supply + - iovdd-supply: Digital IO power supply + See regulator/regulator.txt for more information + +CODEC input pins: + * VINL1 + * VINR1 + * VINL2 + * VINR2 + * VINL3 + * VINR3 + * VINL4 + * VINR4 + +The pins can be used in referring sound node's audio-routing property. + +Example: + + pcm186x: audio-codec@4a { + compatible = "ti,pcm1865"; + reg = <0x4a>; + + avdd-supply = <®_3v3_analog>; + dvdd-supply = <®_3v3>; + iovdd-supply = <®_1v8>; + }; diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt index 0d0ab51105b0..0cf0f819b823 100644 --- a/Documentation/devicetree/bindings/sound/renesas,fsi.txt +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -20,7 +20,7 @@ Required properties: Example: -sh_fsi2: sh_fsi2@0xec230000 { +sh_fsi2: sh_fsi2@ec230000 { compatible = "renesas,sh_fsi2"; reg = <0xec230000 0x400>; interrupts = <0 146 0x4>; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 085bec364caf..5bed9a595772 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -4,7 +4,7 @@ Renesas R-Car sound * Modules ============================================= -Renesas R-Car sound is constructed from below modules +Renesas R-Car and RZ/G sound is constructed from below modules (for Gen2 or later) SCU : Sampling Rate Converter Unit @@ -197,12 +197,17 @@ Ex) [MEM] -> [SRC2] -> [CTU03] -+ sound { + #address-cells = <1>; + #size-cells = <0>; + compatible = "simple-scu-audio-card"; ... - simple-audio-card,cpu-0 { + simple-audio-card,cpu@0 { + reg = <0>; sound-dai = <&rcar_sound 0>; }; - simple-audio-card,cpu-1 { + simple-audio-card,cpu@1 { + reg = <1>; sound-dai = <&rcar_sound 1>; }; simple-audio-card,codec { @@ -334,9 +339,11 @@ Required properties: - compatible : "renesas,rcar_sound-<soctype>", fallbacks "renesas,rcar_sound-gen1" if generation1, and - "renesas,rcar_sound-gen2" if generation2 + "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) "renesas,rcar_sound-gen3" if generation3 Examples with soctypes are: + - "renesas,rcar_sound-r8a7743" (RZ/G1M) + - "renesas,rcar_sound-r8a7745" (RZ/G1E) - "renesas,rcar_sound-r8a7778" (R-Car M1A) - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt index 0a1dc4e1815c..ec20c1271e92 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt @@ -33,7 +33,7 @@ Required properties on RK3288: Example for the rk3188 SPDIF controller: -spdif: spdif@0x1011e000 { +spdif: spdif@1011e000 { compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif"; reg = <0x1011e000 0x2000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 166f2290233b..17c13e74667d 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -140,6 +140,7 @@ sound { simple-audio-card,name = "Cubox Audio"; simple-audio-card,dai-link@0 { /* I2S - HDMI */ + reg = <0>; format = "i2s"; cpu { sound-dai = <&audio1 0>; @@ -150,6 +151,7 @@ sound { }; simple-audio-card,dai-link@1 { /* S/PDIF - HDMI */ + reg = <1>; cpu { sound-dai = <&audio1 1>; }; @@ -159,6 +161,7 @@ sound { }; simple-audio-card,dai-link@2 { /* S/PDIF - S/PDIF */ + reg = <2>; cpu { sound-dai = <&audio1 1>; }; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 40068ec0e9a5..4d51f3f5ea98 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -51,7 +51,7 @@ Optional properties: Example: - sti_uni_player1: sti-uni-player@0x8D81000 { + sti_uni_player1: sti-uni-player@8d81000 { compatible = "st,stih407-uni-player-hdmi"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -63,7 +63,7 @@ Example: st,tdm-mode = <1>; }; - sti_uni_player2: sti-uni-player@0x8D82000 { + sti_uni_player2: sti-uni-player@8d82000 { compatible = "st,stih407-uni-player-pcm-out"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -74,7 +74,7 @@ Example: dma-names = "tx"; }; - sti_uni_player3: sti-uni-player@0x8D85000 { + sti_uni_player3: sti-uni-player@8d85000 { compatible = "st,stih407-uni-player-spdif"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -85,7 +85,7 @@ Example: dma-names = "tx"; }; - sti_uni_reader1: sti-uni-reader@0x8D84000 { + sti_uni_reader1: sti-uni-reader@8d84000 { compatible = "st,stih407-uni-reader-hdmi"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; diff --git a/Documentation/devicetree/bindings/sound/st,stm32-adfsdm.txt b/Documentation/devicetree/bindings/sound/st,stm32-adfsdm.txt new file mode 100644 index 000000000000..864f5b00b031 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,stm32-adfsdm.txt @@ -0,0 +1,63 @@ +STMicroelectronics Audio Digital Filter Sigma Delta modulators(DFSDM) + +The DFSDM allows PDM microphones capture through SPI interface. The Audio +interface is seems as a sub block of the DFSDM device. +For details on DFSDM bindings refer to ../iio/adc/st,stm32-dfsdm-adc.txt + +Required properties: + - compatible: "st,stm32h7-dfsdm-dai". + + - #sound-dai-cells : Must be equal to 0 + + - io-channels : phandle to iio dfsdm instance node. + +Example of a sound card using audio DFSDM node. + + sound_card { + compatible = "audio-graph-card"; + + dais = <&cpu_port>; + }; + + dfsdm: dfsdm@40017000 { + compatible = "st,stm32h7-dfsdm"; + reg = <0x40017000 0x400>; + clocks = <&rcc DFSDM1_CK>; + clock-names = "dfsdm"; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + dfsdm_adc0: filter@0 { + compatible = "st,stm32-dfsdm-dmic"; + reg = <0>; + interrupts = <110>; + dmas = <&dmamux1 101 0x400 0x00>; + dma-names = "rx"; + st,adc-channels = <1>; + st,adc-channel-names = "dmic0"; + st,adc-channel-types = "SPI_R"; + st,adc-channel-clk-src = "CLKOUT"; + st,filter-order = <5>; + + dfsdm_dai0: dfsdm-dai { + compatible = "st,stm32h7-dfsdm-dai"; + #sound-dai-cells = <0>; + io-channels = <&dfsdm_adc0 0>; + cpu_port: port { + dfsdm_endpoint: endpoint { + remote-endpoint = <&dmic0_endpoint>; + }; + }; + }; + }; + + dmic0: dmic@0 { + compatible = "dmic-codec"; + #sound-dai-cells = <0>; + port { + dmic0_endpoint: endpoint { + remote-endpoint = <&dfsdm_endpoint>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index 1f9cd7095337..b1acc1a256ba 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -20,11 +20,6 @@ Required properties: Optional properties: - resets: Reference to a reset controller asserting the SAI - - st,sync: specify synchronization mode. - By default SAI sub-block is in asynchronous mode. - This property sets SAI sub-block as slave of another SAI sub-block. - Must contain the phandle and index of the sai sub-block providing - the synchronization. SAI subnodes: Two subnodes corresponding to SAI sub-block instances A et B can be defined. @@ -44,6 +39,13 @@ SAI subnodes required properties: - pinctrl-names: should contain only value "default" - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt +SAI subnodes Optional properties: + - st,sync: specify synchronization mode. + By default SAI sub-block is in asynchronous mode. + This property sets SAI sub-block as slave of another SAI sub-block. + Must contain the phandle and index of the sai sub-block providing + the synchronization. + The device node should contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in Documentation/devicetree/bindings/ graph.txt. diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index 05d7135a8d2f..b9d50d6cdef3 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -8,6 +8,7 @@ Required properties: - compatible: should be one of the following: - "allwinner,sun4i-a10-i2s" - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" - reg: physical base address of the controller and length of memory mapped region. @@ -23,6 +24,7 @@ Required properties: Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" - resets: phandle to the reset line for this codec diff --git a/Documentation/devicetree/bindings/sound/tas5720.txt b/Documentation/devicetree/bindings/sound/tas5720.txt index 40d94f82beb3..7481653fe8e3 100644 --- a/Documentation/devicetree/bindings/sound/tas5720.txt +++ b/Documentation/devicetree/bindings/sound/tas5720.txt @@ -6,10 +6,12 @@ audio playback. For more product information please see the links below: http://www.ti.com/product/TAS5720L http://www.ti.com/product/TAS5720M +http://www.ti.com/product/TAS5722L Required properties: -- compatible : "ti,tas5720" +- compatible : "ti,tas5720", + "ti,tas5722" - reg : I2C slave address - dvdd-supply : phandle to a 3.3-V supply for the digital circuitry - pvdd-supply : phandle to a supply used for the Class-D amp and the analog diff --git a/Documentation/devicetree/bindings/sound/tfa9879.txt b/Documentation/devicetree/bindings/sound/tfa9879.txt index 23ba522d9e2b..1620e6848436 100644 --- a/Documentation/devicetree/bindings/sound/tfa9879.txt +++ b/Documentation/devicetree/bindings/sound/tfa9879.txt @@ -6,18 +6,18 @@ Required properties: - reg : the I2C address of the device +- #sound-dai-cells : must be 0. + Example: &i2c1 { - clock-frequency = <100000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; - status = "okay"; - codec: tfa9879@6c { + amp: amp@6c { #sound-dai-cells = <0>; compatible = "nxp,tfa9879"; reg = <0x6c>; - }; + }; }; diff --git a/Documentation/devicetree/bindings/sound/ti,tas6424.txt b/Documentation/devicetree/bindings/sound/ti,tas6424.txt new file mode 100644 index 000000000000..1c4ada0eef4e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,tas6424.txt @@ -0,0 +1,20 @@ +Texas Instruments TAS6424 Quad-Channel Audio amplifier + +The TAS6424 serial control bus communicates through I2C protocols. + +Required properties: + - compatible: "ti,tas6424" - TAS6424 + - reg: I2C slave address + - sound-dai-cells: must be equal to 0 + +Example: + +tas6424: tas6424@6a { + compatible = "ti,tas6424"; + reg = <0x6a>; + + #sound-dai-cells = <0>; +}; + +For more product information please see the link below: +http://www.ti.com/product/TAS6424-Q1 diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 6fbba562eaa7..5b3c33bb99e5 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -22,7 +22,7 @@ Required properties: Optional properties: -- gpio-reset - gpio pin number used for codec reset +- reset-gpios - GPIO specification for the active low RESET input. - ai31xx-micbias-vg - MicBias Voltage setting 1 or MICBIAS_2_0V - MICBIAS output is powered to 2.0V 2 or MICBIAS_2_5V - MICBIAS output is powered to 2.5V @@ -30,6 +30,10 @@ Optional properties: If this node is not mentioned or if the value is unknown, then micbias is set to 2.0V. +Deprecated properties: + +- gpio-reset - gpio pin number used for codec reset + CODEC output pins: * HPL * HPR @@ -48,6 +52,7 @@ CODEC input pins: The pins can be used in referring sound node's audio-routing property. Example: +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/sound/tlv320aic31xx-micbias.h> tlv320aic31xx: tlv320aic31xx@18 { @@ -56,6 +61,8 @@ tlv320aic31xx: tlv320aic31xx@18 { ai31xx-micbias-vg = <MICBIAS_OFF>; + reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + HPVDD-supply = <®ulator>; SPRVDD-supply = <®ulator>; SPLVDD-supply = <®ulator>; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index ba5b45c483f5..9796c4639262 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -17,7 +17,7 @@ Required properties: Optional properties: -- gpio-reset - gpio pin number used for codec reset +- reset-gpios - GPIO specification for the active low RESET input. - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality - Not supported on tlv320aic3104 - ai3x-micbias-vg - MicBias Voltage required. @@ -34,6 +34,10 @@ Optional properties: - AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the device as covered in Documentation/devicetree/bindings/regulator/regulator.txt +Deprecated properties: + +- gpio-reset - gpio pin number used for codec reset + CODEC output pins: * LLOUT * RLOUT @@ -61,10 +65,14 @@ The pins can be used in referring sound node's audio-routing property. Example: +#include <dt-bindings/gpio/gpio.h> + tlv320aic3x: tlv320aic3x@1b { compatible = "ti,tlv320aic3x"; reg = <0x1b>; + reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + AVDD-supply = <®ulator>; IOVDD-supply = <®ulator>; DRVDD-supply = <®ulator>; diff --git a/Documentation/devicetree/bindings/sound/tscs42xx.txt b/Documentation/devicetree/bindings/sound/tscs42xx.txt new file mode 100644 index 000000000000..2ac2f0996697 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tscs42xx.txt @@ -0,0 +1,16 @@ +TSCS42XX Audio CODEC + +Required Properties: + + - compatible : "tempo,tscs42A1" for analog mic + "tempo,tscs42A2" for digital mic + + - reg : <0x71> for analog mic + <0x69> for digital mic + +Example: + +wookie: codec@69 { + compatible = "tempo,tscs42A2"; + reg = <0x69>; +}; diff --git a/Documentation/devicetree/bindings/sound/uniphier,evea.txt b/Documentation/devicetree/bindings/sound/uniphier,evea.txt new file mode 100644 index 000000000000..3f31b235f18b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/uniphier,evea.txt @@ -0,0 +1,26 @@ +Socionext EVEA - UniPhier SoC internal codec driver + +Required properties: +- compatible : should be "socionext,uniphier-evea". +- reg : offset and length of the register set for the device. +- clock-names : should include following entries: + "evea", "exiv" +- clocks : a list of phandle, should contain an entry for each + entries in clock-names. +- reset-names : should include following entries: + "evea", "exiv", "adamv" +- resets : a list of phandle, should contain reset entries of + reset-names. +- #sound-dai-cells: should be 1. + +Example: + + codec { + compatible = "socionext,uniphier-evea"; + reg = <0x57900000 0x1000>; + clock-names = "evea", "exiv"; + clocks = <&sys_clk 41>, <&sys_clk 42>; + reset-names = "evea", "exiv", "adamv"; + resets = <&sys_rst 41>, <&sys_rst 42>, <&adamv_rst 0>; + #sound-dai-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt index 2c1e6a43930b..e0fa61a1be0c 100644 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -19,7 +19,7 @@ Recommended properties : Example: -spi1: spi@0x4000c400 { /* USART1 */ +spi1: spi@4000c400 { /* USART1 */ #address-cells = <1>; #size-cells = <0>; compatible = "energymicro,efm32-spi"; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 5bf13960f7f4..e3c48b20b1a6 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -12,24 +12,30 @@ Required properties: - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" See the clock consumer binding, Documentation/devicetree/bindings/clock/clock-bindings.txt -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "tx" and "rx" if present. -Obsolete properties: -- fsl,spi-num-chipselects : Contains the number of the chipselect +Recommended properties: +- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip +select lines can be used, they appear to always generate a pulse between each +word of a transfer. Most use cases will require GPIO based chip selects to +generate a valid transaction. Optional properties: +- num-cs : Number of total chip selects, see spi-bus.txt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names, if present, should include "tx" and "rx". - fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register controlling the SPI_READY handling. Note that to enable the DRCTL consideration, the SPI_READY mode-flag needs to be set too. Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bdd83959019c..80710f0f0448 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -36,7 +36,21 @@ Required properties: Optional properties: - clocks : Must contain a reference to the functional clock. -- num-cs : Total number of chip-selects (default is 1) +- num-cs : Total number of chip selects (default is 1). + Up to 3 native chip selects are supported: + 0: MSIOF_SYNC + 1: MSIOF_SS1 + 2: MSIOF_SS2 + Hardware limitations related to chip selects: + - Native chip selects are always deasserted in + between transfers that are part of the same + message. Use cs-gpios to work around this. + - All slaves using native chip selects must use the + same spi-cs-high configuration. Use cs-gpios to + work around this. + - When using GPIO chip selects, at least one native + chip select must be left unused, as it will be + driven anyway. - dmas : Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index 1925277bfc1e..9f5b4c7c0c08 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -68,7 +68,7 @@ SPI_SOMI/SIMO+-----------------+ +----------- Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus. -spi0:spi@20BF0000 { +spi0:spi@20bf0000 { #address-cells = <1>; #size-cells = <0>; compatible = "ti,dm6446-spi"; diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt index 6069b95a883d..ce3230c8e28d 100644 --- a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt +++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt @@ -16,7 +16,7 @@ Optional properties: Example: -spi: spi@E100800 { +spi: spi@e100800 { compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; reg = <0xE100800 0x100>; interrupt-parent = <&icu0>; diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index 825c39cae74a..b7f5e86fed22 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -27,7 +27,9 @@ The Meson SPICC is generic SPI controller for general purpose Full-Duplex communications with dedicated 16 words RX/TX PIO FIFOs. Required properties: - - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs. + - compatible: should be: + "amlogic,meson-gx-spicc" on Amlogic GX and compatible SoCs. + "amlogic,meson-axg-spicc" on Amlogic AXG and compatible SoCs - reg: physical base address and length of the controller registers - interrupts: The interrupt specifier - clock-names: Must contain "core" diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt index c7b7856bd528..7bf61efc66c8 100644 --- a/Documentation/devicetree/bindings/spi/spi-xilinx.txt +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -2,7 +2,7 @@ Xilinx SPI controller Device Tree Bindings ------------------------------------------------- Required properties: -- compatible : Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b" +- compatible : Should be "xlnx,xps-spi-2.00.a", "xlnx,xps-spi-2.00.b" or "xlnx,axi-quad-spi-1.00.a" - reg : Physical base address and size of SPI registers map. - interrupts : Property with a value describing the interrupt number. diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt index 24aacf8948c5..e0d013a2e66d 100644 --- a/Documentation/devicetree/bindings/thermal/armada-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -2,22 +2,35 @@ Required properties: -- compatible: Should be set to one of the following: - marvell,armada370-thermal - marvell,armada375-thermal - marvell,armada380-thermal - marvell,armadaxp-thermal +- compatible: Should be set to one of the following: + * marvell,armada370-thermal + * marvell,armada375-thermal + * marvell,armada380-thermal + * marvell,armadaxp-thermal + * marvell,armada-ap806-thermal + * marvell,armada-cp110-thermal -- reg: Device's register space. - Two entries are expected, see the examples below. - The first one is required for the sensor register; - the second one is required for the control register - to be used for sensor initialization (a.k.a. calibration). +- reg: Device's register space. + Two entries are expected, see the examples below. The first one points + to the status register (4B). The second one points to the control + registers (8B). + Note: The compatibles marvell,armada370-thermal, + marvell,armada380-thermal, and marvell,armadaxp-thermal must point to + "control MSB/control 1", with size of 4 (deprecated binding), or point + to "control LSB/control 0" with size of 8 (current binding). All other + compatibles must point to "control LSB/control 0" with size of 8. -Example: +Examples: + /* Legacy bindings */ thermal@d0018300 { compatible = "marvell,armada370-thermal"; - reg = <0xd0018300 0x4 + reg = <0xd0018300 0x4 0xd0018304 0x4>; }; + + ap_thermal: thermal@6f8084 { + compatible = "marvell,armada-ap806-thermal"; + reg = <0x6f808C 0x4>, + <0x6f8084 0x8>; + }; diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 9b4c7b017495..1b596fd38dc4 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -70,7 +70,7 @@ Following properties are mandatory (depending on SoC): Example 1): - tmu@100C0000 { + tmu@100c0000 { compatible = "samsung,exynos4412-tmu"; interrupt-parent = <&combiner>; reg = <0x100C0000 0x100>; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index a8e52c8ccfcc..349e635f2d87 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -6,6 +6,7 @@ Required properties: "renesas,rcar-thermal" (without thermal-zone) as fallback. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) + - "renesas,thermal-r8a7743" (RZ/G1M) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - "renesas,thermal-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 88b6ea1ad290..1719d47a5e2f 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -239,7 +239,7 @@ cpus { * A simple fan controller which supports 10 speeds of operation * (represented as 0-9). */ - fan0: fan@0x48 { + fan0: fan@48 { ... cooling-min-level = <0>; cooling-max-level = <9>; @@ -252,7 +252,7 @@ ocp { /* * A simple IC with a single bandgap temperature sensor. */ - bandgap0: bandgap@0x0000ED00 { + bandgap0: bandgap@0000ed00 { ... #thermal-sensor-cells = <0>; }; @@ -330,7 +330,7 @@ ocp { /* * A simple IC with several bandgap temperature sensors. */ - bandgap0: bandgap@0x0000ED00 { + bandgap0: bandgap@0000ed00 { ... #thermal-sensor-cells = <1>; }; @@ -447,7 +447,7 @@ one thermal zone. /* * A simple IC with a single temperature sensor. */ - adc: sensor@0x49 { + adc: sensor@49 { ... #thermal-sensor-cells = <0>; }; @@ -458,7 +458,7 @@ ocp { /* * A simple IC with a single bandgap temperature sensor. */ - bandgap0: bandgap@0x0000ED00 { + bandgap0: bandgap@0000ed00 { ... #thermal-sensor-cells = <0>; }; @@ -516,7 +516,7 @@ with many sensors and many cooling devices. /* * An IC with several temperature sensor. */ - adc_dummy: sensor@0x50 { + adc_dummy: sensor@50 { ... #thermal-sensor-cells = <1>; /* sensor internal ID */ }; diff --git a/Documentation/devicetree/bindings/timer/actions,owl-timer.txt b/Documentation/devicetree/bindings/timer/actions,owl-timer.txt index e3c28da80cb2..977054f87563 100644 --- a/Documentation/devicetree/bindings/timer/actions,owl-timer.txt +++ b/Documentation/devicetree/bindings/timer/actions,owl-timer.txt @@ -2,6 +2,7 @@ Actions Semi Owl Timer Required properties: - compatible : "actions,s500-timer" for S500 + "actions,s700-timer" for S700 "actions,s900-timer" for S900 - reg : Offset and length of the register set for the device. - interrupts : Should contain the interrupts. diff --git a/Documentation/devicetree/bindings/timer/renesas,tpu.txt b/Documentation/devicetree/bindings/timer/renesas,tpu.txt index f8b25897fb31..1d46f9de4feb 100644 --- a/Documentation/devicetree/bindings/timer/renesas,tpu.txt +++ b/Documentation/devicetree/bindings/timer/renesas,tpu.txt @@ -1,4 +1,4 @@ -* Renesas H8/300 Timer Pluse Unit +* Renesas H8/300 Timer Pulse Unit The TPU is a 16bit timer/counter with configurable clock inputs and programmable compare match. diff --git a/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt index 167d5dab9f64..8f78640ad64c 100644 --- a/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt +++ b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt @@ -51,7 +51,7 @@ Example 2: In this example, the timer interrupts are connected to two separate interrupt controllers. Hence, an interrupt-map is created to map the interrupts to the respective interrupt controllers. - mct@101C0000 { + mct@101c0000 { compatible = "samsung,exynos4210-mct"; reg = <0x101C0000 0x800>; interrupt-parent = <&mct_map>; diff --git a/Documentation/devicetree/bindings/timer/spreadtrum,sprd-timer.txt b/Documentation/devicetree/bindings/timer/spreadtrum,sprd-timer.txt new file mode 100644 index 000000000000..6d97e7d0f6e8 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/spreadtrum,sprd-timer.txt @@ -0,0 +1,20 @@ +Spreadtrum timers + +The Spreadtrum SC9860 platform provides 3 general-purpose timers. +These timers can support 32bit or 64bit counter, as well as supporting +period mode or one-shot mode, and they are can be wakeup source +during deep sleep. + +Required properties: +- compatible: should be "sprd,sc9860-timer" for SC9860 platform. +- reg: The register address of the timer device. +- interrupts: Should contain the interrupt for the timer device. +- clocks: The phandle to the source clock (usually a 32.768 KHz fixed clock). + +Example: + timer@40050000 { + compatible = "sprd,sc9860-timer"; + reg = <0 0x40050000 0 0x20>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ext_32k>; + }; diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 5f3143f97098..2e3740f98c41 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -63,6 +63,7 @@ fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) +infineon,tlv493d-a1b6 Infineon TLV493D-A1B6 I2C 3D Magnetic Sensor isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM isil,isl12022 Intersil ISL12022 Real-time Clock @@ -151,6 +152,7 @@ national,lm85 Temperature sensor with integrated fan control national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface nuvoton,npct501 i2c trusted platform module (TPM) nuvoton,npct601 i2c trusted platform module (TPM2) +nuvoton,w83773g Nuvoton Temperature Sensor nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf2127 Real-time clock diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt index 1f69ee1a61ea..21d9a93db2e9 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt @@ -32,7 +32,7 @@ Optional properties: Example: - ufsphy1: ufsphy@0xfc597000 { + ufsphy1: ufsphy@fc597000 { compatible = "qcom,ufs-phy-qmp-20nm"; reg = <0xfc597000 0x800>; reg-names = "phy_mem"; @@ -53,7 +53,7 @@ Example: <&clock_gcc clk_gcc_ufs_rx_cfg_clk>; }; - ufshc@0xfc598000 { + ufshc@fc598000 { ... phys = <&ufsphy1>; phy-names = "ufsphy"; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index a99ed5565b26..c39dfef76a18 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -46,7 +46,7 @@ Note: If above properties are not defined it can be assumed that the supply regulators or clocks are always on. Example: - ufshc@0xfc598000 { + ufshc@fc598000 { compatible = "jedec,ufs-1.1"; reg = <0xfc598000 0x800>; interrupts = <0 28 0>; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index 7a33f22c815a..7a198a30408a 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -95,6 +95,7 @@ usb: usb@47400000 { reg = <0x47401300 0x100>; reg-names = "phy"; ti,ctrl_mod = <&ctrl_mod>; + #phy-cells = <0>; }; usb0: usb@47401000 { @@ -141,6 +142,7 @@ usb: usb@47400000 { reg = <0x47401b00 0x100>; reg-names = "phy"; ti,ctrl_mod = <&ctrl_mod>; + #phy-cells = <0>; }; usb1: usb@47401800 { diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt index 9feea6c3e4d9..065c91d955ad 100644 --- a/Documentation/devicetree/bindings/usb/ehci-st.txt +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -22,7 +22,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt Example: - ehci1: usb@0xfe203e00 { + ehci1: usb@fe203e00 { compatible = "st,st-ehci-300x"; reg = <0xfe203e00 0x100>; interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt index d893ec9131c3..44c998c16f85 100644 --- a/Documentation/devicetree/bindings/usb/ohci-st.txt +++ b/Documentation/devicetree/bindings/usb/ohci-st.txt @@ -20,7 +20,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt Example: - ohci0: usb@0xfe1ffc00 { + ohci0: usb@fe1ffc00 { compatible = "st,st-ohci-300x"; reg = <0xfe1ffc00 0x100>; interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt index 50a31536e975..2c3f6a467fda 100644 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -1,7 +1,9 @@ Rockchip SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC +- compatible: should be one of the following: + - "rockchip,rk3399-dwc3": for rk3399 SoC + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC - clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names - clock-names: Should contain the following: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 0994bdd82cd3..2fd0d54c6a15 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -15,6 +15,7 @@ adi Analog Devices, Inc. advantech Advantech Corporation aeroflexgaisler Aeroflex Gaisler AB al Annapurna Labs +allo Allo.com allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. @@ -154,6 +155,7 @@ i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. ifi Ingenieurburo Fur Ic-Technologie (I/F/I) +ilitek ILI Technology Corporation (ILITEK) img Imagination Technologies Ltd. infineon Infineon Technologies inforce Inforce Computing @@ -172,6 +174,7 @@ itead ITEAD Intelligent Systems Co.Ltd iwave iWave Systems Technologies Pvt. Ltd. jdi Japan Display Inc. jedec JEDEC Solid State Technology Association +jianda Jiandangjing Technology Co., Ltd. karo Ka-Ro electronics GmbH keithkoep Keith & Koep GmbH keymile Keymile GmbH @@ -305,6 +308,7 @@ seagate Seagate Technology PLC semtech Semtech Corporation sensirion Sensirion AG sff Small Form Factor Committee +sgd Solomon Goldentek Display Corporation sgx SGX Sensortech sharp Sharp Corporation shimafuji Shimafuji Electric, Inc. @@ -347,6 +351,7 @@ tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems +tempo Tempo Semiconductor terasic Terasic Inc. thine THine Electronics, Inc. ti Texas Instruments @@ -379,6 +384,7 @@ virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation vocore VoCore Studio voipac Voipac Technologies s.r.o. +vot Vision Optical Technology Co., Ltd. wd Western Digital Corp. wetek WeTek Electronics, limited. wexler Wexler diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt b/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt deleted file mode 100644 index bc4b865d178b..000000000000 --- a/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt +++ /dev/null @@ -1,17 +0,0 @@ -Cortina Systems Gemini SoC Watchdog - -Required properties: -- compatible : must be "cortina,gemini-watchdog" -- reg : shall contain base register location and length -- interrupts : shall contain the interrupt for the watchdog - -Optional properties: -- timeout-sec : the default watchdog timeout in seconds. - -Example: - -watchdog@41000000 { - compatible = "cortina,gemini-watchdog"; - reg = <0x41000000 0x1000>; - interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt index bc4b865d178b..9ecdb502e605 100644 --- a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt +++ b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt @@ -1,7 +1,12 @@ -Cortina Systems Gemini SoC Watchdog +Faraday Technology FTWDT010 watchdog + +This is an IP part from Faraday Technology found in the Gemini +SoCs and others. Required properties: -- compatible : must be "cortina,gemini-watchdog" +- compatible : must be one of + "faraday,ftwdt010" + "cortina,gemini-watchdog", "faraday,ftwdt010" - reg : shall contain base register location and length - interrupts : shall contain the interrupt for the watchdog @@ -11,7 +16,7 @@ Optional properties: Example: watchdog@41000000 { - compatible = "cortina,gemini-watchdog"; + compatible = "faraday,ftwdt010"; reg = <0x41000000 0x1000>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt index e27763ef0049..cb44918f01a8 100644 --- a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt @@ -1,12 +1,12 @@ -Ingenic Watchdog Timer (WDT) Controller for JZ4740 +Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780 Required properties: -compatible: "ingenic,jz4740-watchdog" +compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog" reg: Register address and length for watchdog registers Example: -watchdog: jz4740-watchdog@0x10002000 { +watchdog: jz4740-watchdog@10002000 { compatible = "ingenic,jz4740-watchdog"; reg = <0x10002000 0x100>; }; diff --git a/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt index 556d06c17c92..4b76bec62af9 100644 --- a/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt @@ -10,7 +10,7 @@ Optional properties: Example: - watchdog@4003C000 { + watchdog@4003c000 { compatible = "nxp,pnx4008-wdt"; reg = <0x4003C000 0x1000>; timeout-sec = <10>; diff --git a/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt new file mode 100644 index 000000000000..05653054bd5b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt @@ -0,0 +1,17 @@ +Realtek RTD1295 Watchdog +======================== + +Required properties: + +- compatible : Should be "realtek,rtd1295-watchdog" +- reg : Specifies the physical base address and size of registers +- clocks : Specifies one clock input + + +Example: + + watchdog@98007680 { + compatible = "realtek,rtd1295-watchdog"; + reg = <0x98007680 0x100>; + clocks = <&osc27M>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index bf6d1ca58af7..74b2f03c1515 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -4,10 +4,11 @@ Required properties: - compatible : Should be "renesas,<soctype>-wdt", and "renesas,rcar-gen3-wdt" or "renesas,rza-wdt" as fallback. Examples with soctypes are: + - "renesas,r7s72100-wdt" (RZ/A1) - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r8a77970-wdt" (R-Car V3M) - "renesas,r8a77995-wdt" (R-Car D3) - - "renesas,r7s72100-wdt" (RZ/A1) When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the generic diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 1f6e101e299a..46dcb48e75b4 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -25,7 +25,7 @@ Optional properties: Example: -watchdog@101D0000 { +watchdog@101d0000 { compatible = "samsung,exynos5250-wdt"; reg = <0x101D0000 0x100>; interrupts = <0 42 0>; diff --git a/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt new file mode 100644 index 000000000000..aeaf3e0caf47 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt @@ -0,0 +1,19 @@ +Spreadtrum SoCs Watchdog timer + +Required properties: +- compatible : Should be "sprd,sp9860-wdt". +- reg : Specifies base physical address and size of the registers. +- interrupts : Exactly one interrupt specifier. +- timeout-sec : Contain the default watchdog timeout in seconds. +- clock-names : Contain the input clock names. +- clocks : Phandles to input clocks. + +Example: + watchdog: watchdog@40310000 { + compatible = "sprd,sp9860-wdt"; + reg = <0 0x40310000 0 0x1000>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + timeout-sec = <12>; + clock-names = "enable", "rtc_enable"; + clocks = <&clk_aon_apb_gates1 8>, <&clk_aon_apb_rtc_gates 9>; + }; |