diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
-rw-r--r-- | Documentation/kernel-parameters.txt | 38 |
1 files changed, 34 insertions, 4 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index e07c432c731f..5134d63a84a4 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -147,10 +147,14 @@ and is between 256 and 4096 characters. It is defined in the file default: 0 acpi_sleep= [HW,ACPI] Sleep options - Format: { s3_bios, s3_mode, s3_beep } + Format: { s3_bios, s3_mode, s3_beep, old_ordering } See Documentation/power/video.txt for s3_bios and s3_mode. s3_beep is for debugging; it makes the PC's speaker beep as soon as the kernel's real-mode entry point is called. + old_ordering causes the ACPI 1.0 ordering of the _PTS + control method, wrt putting devices into low power + states, to be enforced (the ACPI 2.0 ordering of _PTS is + used by default). acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode Format: { level | edge | high | low } @@ -599,6 +603,29 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/digiepca.txt. + disable_mtrr_cleanup [X86] + enable_mtrr_cleanup [X86] + The kernel tries to adjust MTRR layout from continuous + to discrete, to make X server driver able to add WB + entry later. This parameter enables/disables that. + + mtrr_chunk_size=nn[KMG] [X86] + used for mtrr cleanup. It is largest continous chunk + that could hold holes aka. UC entries. + + mtrr_gran_size=nn[KMG] [X86] + Used for mtrr cleanup. It is granularity of mtrr block. + Default is 1. + Large value could prevent small alignment from + using up MTRRs. + + mtrr_spare_reg_nr=n [X86] + Format: <integer> + Range: 0,7 : spare reg number + Default : 1 + Used for mtrr cleanup. It is spare mtrr entries number. + Set to 2 or more if your graphical card needs more. + disable_mtrr_trim [X86, Intel and AMD only] By default the kernel will trim any uncacheable memory out of your available memory pool based on @@ -722,9 +749,6 @@ and is between 256 and 4096 characters. It is defined in the file hd= [EIDE] (E)IDE hard drive subsystem geometry Format: <cyl>,<head>,<sect> - hd?= [HW] (E)IDE subsystem - hd?lun= See Documentation/ide/ide.txt. - highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact size of <nn>. This works even on boxes that have no highmem otherwise. This also works to reduce highmem @@ -1496,6 +1520,9 @@ and is between 256 and 4096 characters. It is defined in the file Use with caution as certain devices share address decoders between ROMs and other resources. + norom [X86-32,X86_64] Do not assign address space to + expansion ROMs that do not already have + BIOS assigned address ranges. irqmask=0xMMMM [X86-32] Set a bit mask of IRQs allowed to be assigned automatically to PCI devices. You can make the kernel exclude IRQs of your ISA cards @@ -1971,6 +1998,9 @@ and is between 256 and 4096 characters. It is defined in the file snd-ymfpci= [HW,ALSA] + softlockup_panic= + [KNL] Should the soft-lockup detector generate panics. + sonypi.*= [HW] Sony Programmable I/O Control Device driver See Documentation/sonypi.txt |