summaryrefslogtreecommitdiff
path: root/arch/cris/arch-v10/drivers/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'arch/cris/arch-v10/drivers/Kconfig')
-rw-r--r--arch/cris/arch-v10/drivers/Kconfig561
1 files changed, 0 insertions, 561 deletions
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
deleted file mode 100644
index 8792af63c049..000000000000
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ /dev/null
@@ -1,561 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-if ETRAX_ARCH_V10
-
-config ETRAX_ETHERNET
- bool "Ethernet support"
- depends on ETRAX_ARCH_V10 && NETDEVICES
- select MII
- help
- This option enables the ETRAX 100LX built-in 10/100Mbit Ethernet
- controller.
-
-config ETRAX_SERIAL
- bool "Serial-port support"
- depends on ETRAX_ARCH_V10
- help
- Enables the ETRAX 100 serial driver for ser0 (ttyS0)
- You probably want this enabled.
-
-config ETRAX_SERIAL_FAST_TIMER
- bool "Use fast timers for serial DMA flush (experimental)"
- depends on ETRAX_SERIAL
- help
- Select this to have the serial DMAs flushed at a higher rate than
- normally, possible by using the fast timer API, the timeout is
- approx. 4 character times.
- If unsure, say N.
-
-config ETRAX_SERIAL_FLUSH_DMA_FAST
- bool "Fast serial port DMA flush"
- depends on ETRAX_SERIAL && !ETRAX_SERIAL_FAST_TIMER
- help
- Select this to have the serial DMAs flushed at a higher rate than
- normally possible through a fast timer interrupt (currently at
- 15360 Hz).
- If unsure, say N.
-
-config ETRAX_SERIAL_RX_TIMEOUT_TICKS
- int "Receive flush timeout (ticks) "
- depends on ETRAX_SERIAL && !ETRAX_SERIAL_FAST_TIMER && !ETRAX_SERIAL_FLUSH_DMA_FAST
- default "5"
- help
- Number of timer ticks between flush of receive fifo (1 tick = 10ms).
- Try 0-3 for low latency applications. Approx 5 for high load
- applications (e.g. PPP). Maybe this should be more adaptive some
- day...
-
-config ETRAX_SERIAL_PORT0
- bool "Serial port 0 enabled"
- depends on ETRAX_SERIAL
- help
- Enables the ETRAX 100 serial driver for ser0 (ttyS0)
- Normally you want this on, unless you use external DMA 1 that uses
- the same DMA channels.
-
-choice
- prompt "Ser0 DTR, RI, DSR and CD assignment"
- depends on ETRAX_SERIAL_PORT0
- default ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE
-
-config ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE
- bool "No_DTR_RI_DSR_CD"
-
-config ETRAX_SER0_DTR_RI_DSR_CD_ON_PA
- bool "DTR_RI_DSR_CD_on_PA"
-
-config ETRAX_SER0_DTR_RI_DSR_CD_ON_PB
- bool "DTR_RI_DSR_CD_on_PB"
- help
- Enables the status and control signals DTR, RI, DSR and CD on PB for
- ser0.
-
-config ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"
-
-endchoice
-
-config ETRAX_SER0_DTR_ON_PA_BIT
- int "Ser0 DTR on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER0_RI_ON_PA_BIT
- int "Ser0 RI on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER0_DSR_ON_PA_BIT
- int "Ser0 DSR on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER0_CD_ON_PA_BIT
- int "Ser0 CD on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER0_DTR_ON_PB_BIT
- int "Ser0 DTR on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the DTR signal for serial
- port 0.
-
-config ETRAX_SER0_RI_ON_PB_BIT
- int "Ser0 RI on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the RI signal for serial
- port 0.
-
-config ETRAX_SER0_DSR_ON_PB_BIT
- int "Ser0 DSR on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the DSR signal for serial
- port 0.
-
-config ETRAX_SER0_CD_ON_PB_BIT
- int "Ser0 CD on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT0
- default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the CD signal for serial
- port 0.
-
-config ETRAX_SERIAL_PORT1
- bool "Serial port 1 enabled"
- depends on ETRAX_SERIAL
- help
- Enables the ETRAX 100 serial driver for ser1 (ttyS1).
-
-choice
- prompt "Ser1 DTR, RI, DSR and CD assignment"
- depends on ETRAX_SERIAL_PORT1
- default ETRAX_SER1_DTR_RI_DSR_CD_ON_NONE
-
-config ETRAX_SER1_DTR_RI_DSR_CD_ON_NONE
- bool "No_DTR_RI_DSR_CD"
-
-config ETRAX_SER1_DTR_RI_DSR_CD_ON_PA
- bool "DTR_RI_DSR_CD_on_PA"
-
-config ETRAX_SER1_DTR_RI_DSR_CD_ON_PB
- bool "DTR_RI_DSR_CD_on_PB"
- help
- Enables the status and control signals DTR, RI, DSR and CD on PB for
- ser1.
-
-config ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"
-
-endchoice
-
-config ETRAX_SER1_DTR_ON_PA_BIT
- int "Ser1 DTR on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER1_RI_ON_PA_BIT
- int "Ser1 RI on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER1_DSR_ON_PA_BIT
- int "Ser1 DSR on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER1_CD_ON_PA_BIT
- int "Ser1 CD on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER1_DTR_ON_PB_BIT
- int "Ser1 DTR on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the DTR signal for serial
- port 1.
-
-config ETRAX_SER1_RI_ON_PB_BIT
- int "Ser1 RI on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the RI signal for serial
- port 1.
-
-config ETRAX_SER1_DSR_ON_PB_BIT
- int "Ser1 DSR on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the DSR signal for serial
- port 1.
-
-config ETRAX_SER1_CD_ON_PB_BIT
- int "Ser1 CD on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT1
- default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PB port to carry the CD signal for serial
- port 1.
-
-comment "Make sure you do not have the same PB bits more than once!"
- depends on ETRAX_SERIAL && ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && ETRAX_SER1_DTR_RI_DSR_CD_ON_PB
-
-config ETRAX_SERIAL_PORT2
- bool "Serial port 2 enabled"
- depends on ETRAX_SERIAL
- help
- Enables the ETRAX 100 serial driver for ser2 (ttyS2).
-
-choice
- prompt "Ser2 DTR, RI, DSR and CD assignment"
- depends on ETRAX_SERIAL_PORT2
- default ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE
-
-config ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE
- bool "No_DTR_RI_DSR_CD"
-
-config ETRAX_SER2_DTR_RI_DSR_CD_ON_PA
- bool "DTR_RI_DSR_CD_on_PA"
- help
- Enables the status and control signals DTR, RI, DSR and CD on PA for
- ser2.
-
-config ETRAX_SER2_DTR_RI_DSR_CD_ON_PB
- bool "DTR_RI_DSR_CD_on_PB"
-
-config ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"
-
-endchoice
-
-config ETRAX_SER2_DTR_ON_PA_BIT
- int "Ser2 DTR on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PA port to carry the DTR signal for serial
- port 2.
-
-config ETRAX_SER2_RI_ON_PA_BIT
- int "Ser2 RI on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PA port to carry the RI signal for serial
- port 2.
-
-config ETRAX_SER2_DSR_ON_PA_BIT
- int "Ser2 DSR on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PA port to carry the DTR signal for serial
- port 2.
-
-config ETRAX_SER2_CD_ON_PA_BIT
- int "Ser2 CD on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- help
- Specify the pin of the PA port to carry the CD signal for serial
- port 2.
-
-config ETRAX_SER2_DTR_ON_PB_BIT
- int "Ser2 DTR on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "4" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER2_RI_ON_PB_BIT
- int "Ser2 RI on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "5" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER2_DSR_ON_PB_BIT
- int "Ser2 DSR on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "6" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SER2_CD_ON_PB_BIT
- int "Ser2 CD on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT2
- default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
- default "7" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-
-config ETRAX_SERIAL_PORT3
- bool "Serial port 3 enabled"
- depends on ETRAX_SERIAL
- help
- Enables the ETRAX 100 serial driver for ser3 (ttyS3).
-
-choice
- prompt "Ser3 DTR, RI, DSR and CD assignment"
- depends on ETRAX_SERIAL_PORT3
- default ETRAX_SER3_DTR_RI_DSR_CD_ON_NONE
-
-config ETRAX_SER3_DTR_RI_DSR_CD_ON_NONE
- bool "No_DTR_RI_DSR_CD"
-
-config ETRAX_SER3_DTR_RI_DSR_CD_ON_PA
- bool "DTR_RI_DSR_CD_on_PA"
-
-config ETRAX_SER3_DTR_RI_DSR_CD_ON_PB
- bool "DTR_RI_DSR_CD_on_PB"
-
-config ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"
-
-endchoice
-
-config ETRAX_SER3_DTR_ON_PA_BIT
- int "Ser3 DTR on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_RI_ON_PA_BIT
- int "Ser3 RI on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_DSR_ON_PA_BIT
- int "Ser3 DSR on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_CD_ON_PA_BIT
- int "Ser3 CD on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_DTR_ON_PB_BIT
- int "Ser3 DTR on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_RI_ON_PB_BIT
- int "Ser3 RI on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_DSR_ON_PB_BIT
- int "Ser3 DSR on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_SER3_CD_ON_PB_BIT
- int "Ser3 CD on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
- depends on ETRAX_SERIAL_PORT3
- default "-1"
-
-config ETRAX_RS485
- bool "RS-485 support"
- depends on ETRAX_SERIAL
- help
- Enables support for RS-485 serial communication. For a primer on
- RS-485, see <http://en.wikipedia.org/wiki/Rs485>
-
-config ETRAX_RS485_ON_PA
- bool "RS-485 mode on PA"
- depends on ETRAX_RS485
- help
- Control Driver Output Enable on RS485 transceiver using a pin on PA
- port:
- Axis 2400/2401 uses PA 3.
-
-config ETRAX_RS485_ON_PA_BIT
- int "RS-485 mode on PA bit"
- depends on ETRAX_RS485_ON_PA
- default "3"
- help
- Control Driver Output Enable on RS485 transceiver using a this bit
- on PA port.
-
-config ETRAX_RS485_DISABLE_RECEIVER
- bool "Disable serial receiver"
- depends on ETRAX_RS485
- help
- It's necessary to disable the serial receiver to avoid serial
- loopback. Not all products are able to do this in software only.
- Axis 2400/2401 must disable receiver.
-
-config ETRAX_USB_HOST
- bool "USB host"
- select USB
- help
- This option enables the host functionality of the ETRAX 100LX
- built-in USB controller. In host mode the controller is designed
- for CTRL and BULK traffic only, INTR traffic may work as well
- however (depending on the requirements of timeliness).
-
-config ETRAX_PTABLE_SECTOR
- int "Byte-offset of partition table sector"
- depends on ETRAX_AXISFLASHMAP
- default "65536"
- help
- Byte-offset of the partition table in the first flash chip.
- The default value is 64kB and should not be changed unless
- you know exactly what you are doing. The only valid reason
- for changing this is when the flash block size is bigger
- than 64kB (e.g. when using two parallel 16 bit flashes).
-
-config ETRAX_I2C
- bool "I2C support"
- depends on ETRAX_ARCH_V10
- help
- Enables an I2C driver on ETRAX100.
- EXAMPLE usage:
- i2c_arg = I2C_WRITEARG(STA013_WRITE_ADDR, reg, val);
- ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_WRITEREG), i2c_arg);
- i2c_arg = I2C_READARG(STA013_READ_ADDR, reg);
- val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg);
-
-# this is true for most products since PB-I2C seems to be somewhat
-# flawed..
-config ETRAX_I2C_USES_PB_NOT_PB_I2C
- bool "I2C uses PB not PB-I2C"
- depends on ETRAX_I2C
- help
- Select whether to use the special I2C mode in the PB I/O register or
- not. This option needs to be selected in order to use some drivers
- that access the I2C I/O pins directly instead of going through the
- I2C driver, like the DS1302 realtime-clock driver. If you are
- uncertain, choose Y here.
-
-config ETRAX_I2C_DATA_PORT
- int "I2C SDA bit number"
- depends on ETRAX_I2C_USES_PB_NOT_PB_I2C
- default "0"
- help
- Selects the pin on Port B where the data pin is connected
-
-config ETRAX_I2C_CLK_PORT
- int "I2C SCL bit number"
- depends on ETRAX_I2C_USES_PB_NOT_PB_I2C
- default "1"
- help
- Select the pin on Port B where the clock pin is connected
-
-config ETRAX_I2C_EEPROM
- bool "I2C EEPROM (non-volatile RAM) support"
- depends on ETRAX_I2C
- help
- Enables I2C EEPROM (non-volatile RAM) on PB0 and PB1 using the I2C
- driver. Select size option: Probed, 2k, 8k, 16k.
- (Probing works for 2k and 8k but not that well for 16k)
-
-choice
- prompt "EEPROM size"
- depends on ETRAX_I2C_EEPROM
- default ETRAX_I2C_EEPROM_PROBE
-
-config ETRAX_I2C_EEPROM_PROBE
- bool "Probed"
- help
- Specifies size or auto probe of the EEPROM size.
- Options: Probed, 2k, 8k, 16k.
- (Probing works for 2k and 8k but not that well for 16k)
-
-config ETRAX_I2C_EEPROM_2KB
- bool "2kB"
- help
- Use a 2kB EEPROM.
-
-config ETRAX_I2C_EEPROM_8KB
- bool "8kB"
- help
- Use a 8kB EEPROM.
-
-config ETRAX_I2C_EEPROM_16KB
- bool "16kB"
- help
- Use a 16kB EEPROM.
-
-endchoice
-
-config ETRAX_GPIO
- bool "GPIO support"
- depends on ETRAX_ARCH_V10
- ---help---
- Enables the ETRAX general port device (major 120, minors 0 and 1).
- You can use this driver to access the general port bits. It supports
- these ioctl's:
- #include <linux/etraxgpio.h>
- fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
- ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
- ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
- val = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READBITS), NULL);
- Remember that you need to setup the port directions appropriately in
- the General configuration.
-
-config ETRAX_PA_CHANGEABLE_DIR
- hex "PA user changeable dir mask"
- depends on ETRAX_GPIO
- default "00"
- help
- This is a bitmask with information of what bits in PA that a user
- can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 00 here.
-
-config ETRAX_PA_CHANGEABLE_BITS
- hex "PA user changeable bits mask"
- depends on ETRAX_GPIO
- default "FF"
- help
- This is a bitmask with information of what bits in PA that a user
- can change the value on using ioctl's.
- Bit set = changeable.
- You probably want 00 here.
-
-config ETRAX_PB_CHANGEABLE_DIR
- hex "PB user changeable dir mask"
- depends on ETRAX_GPIO
- default "00"
- help
- This is a bitmask with information of what bits in PB that a user
- can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 00 here.
-
-config ETRAX_PB_CHANGEABLE_BITS
- hex "PB user changeable bits mask"
- depends on ETRAX_GPIO
- default "FF"
- help
- This is a bitmask with information of what bits in PB that a user
- can change the value on using ioctl's.
- Bit set = changeable.
- You probably want 00 here.
-
-endif