3 files changed, 10 insertions, 41 deletions
diff --git a/arch/frv/include/asm/gdb-stub.h b/arch/frv/include/asm/gdb-stub.h
index 2da716407ff2..e6bedd0cd9a5 100644
--- a/arch/frv/include/asm/gdb-stub.h
+++ b/arch/frv/include/asm/gdb-stub.h
@@ -12,6 +12,7 @@
 #ifndef __ASM_GDB_STUB_H
 #define __ASM_GDB_STUB_H
 
+#undef GDBSTUB_DEBUG_IO
 #undef GDBSTUB_DEBUG_PROTOCOL
 
 #include <asm/ptrace.h>
@@ -108,6 +109,12 @@ extern void gdbstub_printk(const char *fmt, ...);
 extern void debug_to_serial(const char *p, int n);
 extern void console_set_baud(unsigned baud);
 
+#ifdef GDBSTUB_DEBUG_IO
+#define gdbstub_io(FMT,...) gdbstub_printk(FMT, ##__VA_ARGS__)
+#else
+#define gdbstub_io(FMT,...) ({ 0; })
+#endif
+
 #ifdef GDBSTUB_DEBUG_PROTOCOL
 #define gdbstub_proto(FMT,...) gdbstub_printk(FMT,##__VA_ARGS__)
 #else
diff --git a/arch/frv/include/asm/mem-layout.h b/arch/frv/include/asm/mem-layout.h
index 2947764fc0e0..ccae981876fa 100644
--- a/arch/frv/include/asm/mem-layout.h
+++ b/arch/frv/include/asm/mem-layout.h
@@ -35,8 +35,8 @@
  * the slab must be aligned such that load- and store-double instructions don't
  * fault if used
  */
-#define	ARCH_KMALLOC_MINALIGN		8
-#define	ARCH_SLAB_MINALIGN		8
+#define	ARCH_KMALLOC_MINALIGN		L1_CACHE_BYTES
+#define	ARCH_SLAB_MINALIGN		L1_CACHE_BYTES
 
 /*****************************************************************************/
 /*
diff --git a/arch/frv/include/asm/scatterlist.h b/arch/frv/include/asm/scatterlist.h
index 4bca8a28546c..1614bfd7e3a4 100644
--- a/arch/frv/include/asm/scatterlist.h
+++ b/arch/frv/include/asm/scatterlist.h
@@ -1,45 +1,7 @@
 #ifndef _ASM_SCATTERLIST_H
 #define _ASM_SCATTERLIST_H
 
-#include <asm/types.h>
-
-/*
- * Drivers must set either ->address or (preferred) page and ->offset
- * to indicate where data must be transferred to/from.
- *
- * Using page is recommended since it handles highmem data as well as
- * low mem. ->address is restricted to data which has a virtual mapping, and
- * it will go away in the future. Updating to page can be automated very
- * easily -- something like
- *
- * sg->address = some_ptr;
- *
- * can be rewritten as
- *
- * sg_set_buf(sg, some_ptr, length);
- *
- * and that's it. There's no excuse for not highmem enabling YOUR driver. /jens
- */
-struct scatterlist {
-#ifdef CONFIG_DEBUG_SG
-	unsigned long	sg_magic;
-#endif
-	unsigned long	page_link;
-	unsigned int	offset;		/* for highmem, page offset */
-
-	dma_addr_t	dma_address;
-	unsigned int	length;
-};
-
-/*
- * These macros should be used after a pci_map_sg call has been done
- * to get bus addresses of each of the SG entries and their lengths.
- * You should only work with the number of sg entries pci_map_sg
- * returns, or alternatively stop on the first sg_dma_len(sg) which
- * is 0.
- */
-#define sg_dma_address(sg)	((sg)->dma_address)
-#define sg_dma_len(sg)		((sg)->length)
+#include <asm-generic/scatterlist.h>
 
 #define ISA_DMA_THRESHOLD (0xffffffffUL)