summaryrefslogtreecommitdiff
path: root/arch/powerpc/boot/dts/akebono.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/powerpc/boot/dts/akebono.dts')
-rw-r--r--arch/powerpc/boot/dts/akebono.dts415
1 files changed, 415 insertions, 0 deletions
diff --git a/arch/powerpc/boot/dts/akebono.dts b/arch/powerpc/boot/dts/akebono.dts
new file mode 100644
index 000000000000..f92ecfed3d2f
--- /dev/null
+++ b/arch/powerpc/boot/dts/akebono.dts
@@ -0,0 +1,415 @@
+/*
+ * Device Tree Source for IBM Embedded PPC 476 Platform
+ *
+ * Copyright © 2013 Tony Breeds IBM Corporation
+ * Copyright © 2013 Alistair Popple IBM Corporation
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x01f00000 0x00100000; // spin table
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ model = "ibm,akebono";
+ compatible = "ibm,akebono", "ibm,476gtr";
+ dcr-parent = <&{/cpus/cpu@0}>;
+
+ aliases {
+ serial0 = &UART0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,476";
+ reg = <0>;
+ clock-frequency = <1600000000>; // 1.6 GHz
+ timebase-frequency = <100000000>; // 100Mhz
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "ok";
+ };
+ cpu@1 {
+ device_type = "cpu";
+ model = "PowerPC,476";
+ reg = <1>;
+ clock-frequency = <1600000000>; // 1.6 GHz
+ timebase-frequency = <100000000>; // 100Mhz
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "disabled";
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x01f00000>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x0>; // filled in by zImage
+ };
+
+ MPIC: interrupt-controller {
+ compatible = "chrp,open-pic";
+ interrupt-controller;
+ dcr-reg = <0xffc00000 0x00040000>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ single-cpu-affinity;
+ };
+
+ plb {
+ compatible = "ibm,plb6";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clock-frequency = <200000000>; // 200Mhz
+
+ HSTA0: hsta@310000e0000 {
+ compatible = "ibm,476gtr-hsta-msi", "ibm,hsta-msi";
+ reg = <0x310 0x000e0000 0x0 0xf0>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <108 0
+ 109 0
+ 110 0
+ 111 0
+ 112 0
+ 113 0
+ 114 0
+ 115 0
+ 116 0
+ 117 0
+ 118 0
+ 119 0
+ 120 0
+ 121 0
+ 122 0
+ 123 0>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-476gtr", "ibm,mcmal2";
+ dcr-reg = <0xc0000000 0x062>;
+ num-tx-chans = <1>;
+ num-rx-chans = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-parent = <&MPIC>;
+ interrupts = < /*TXEOB*/ 77 0x4
+ /*RXEOB*/ 78 0x4
+ /*SERR*/ 76 0x4
+ /*TXDE*/ 79 0x4
+ /*RXDE*/ 80 0x4>;
+ };
+
+ SATA0: sata@30000010000 {
+ compatible = "ibm,476gtr-ahci";
+ reg = <0x300 0x00010000 0x0 0x10000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <93 2>;
+ };
+
+ EHCI0: ehci@30010000000 {
+ compatible = "ibm,476gtr-ehci", "generic-ehci";
+ reg = <0x300 0x10000000 0x0 0x10000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <85 2>;
+ };
+
+ SD0: sd@30000000000 {
+ compatible = "ibm,476gtr-sdhci", "generic-sdhci";
+ reg = <0x300 0x00000000 0x0 0x10000>;
+ interrupts = <91 2>;
+ interrupt-parent = <&MPIC>;
+ };
+
+ OHCI0: ohci@30010010000 {
+ compatible = "ibm,476gtr-ohci", "generic-ohci";
+ reg = <0x300 0x10010000 0x0 0x10000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <89 1>;
+ };
+
+ OHCI1: ohci@30010020000 {
+ compatible = "ibm,476gtr-ohci", "generic-ohci";
+ reg = <0x300 0x10020000 0x0 0x10000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <88 1>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-4xx", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* Wish there was a nicer way of specifying a full
+ * 32-bit range
+ */
+ ranges = <0x00000000 0x0000033f 0x00000000 0x80000000
+ 0x80000000 0x0000033f 0x80000000 0x80000000>;
+ clock-frequency = <100000000>;
+
+ RGMII0: emac-rgmii-wol@50004 {
+ compatible = "ibm,rgmii-wol-476gtr", "ibm,rgmii-wol";
+ reg = <0x50004 0x00000008>;
+ has-mdio;
+ };
+
+ EMAC0: ethernet@30000 {
+ device_type = "network";
+ compatible = "ibm,emac-476gtr", "ibm,emac4sync";
+ interrupt-parent = <&EMAC0>;
+ interrupts = <0x0 0x1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0x0 &MPIC 81 0x4
+ /*Wake*/ 0x1 &MPIC 82 0x4>;
+ reg = <0x30000 0x78>;
+
+ /* local-mac-address will normally be added by
+ * the wrapper. If your device doesn't support
+ * passing data to the wrapper (in the form
+ * local-mac-addr=<hwaddr>) then you will need
+ * to set it manually here. */
+ //local-mac-address = [000000000000];
+
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <4096>;
+ tx-fifo-size = <2048>;
+ rx-fifo-size-gige = <16384>;
+ phy-mode = "rgmii";
+ phy-map = <0x00000000>;
+ rgmii-wol-device = <&RGMII0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ UART0: serial@10000 {
+ device_type = "serial";
+ compatible = "ns16750", "ns16550";
+ reg = <0x10000 0x00000008>;
+ virtual-reg = <0xe8010000>;
+ clock-frequency = <1851851>;
+ current-speed = <38400>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <39 2>;
+ };
+
+ IIC0: i2c@00000000 {
+ compatible = "ibm,iic-476gtr", "ibm,iic";
+ reg = <0x0 0x00000020>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <37 2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ rtc@68 {
+ compatible = "stm,m41t80", "m41st85";
+ reg = <0x68>;
+ };
+ };
+
+ IIC1: i2c@00000100 {
+ compatible = "ibm,iic-476gtr", "ibm,iic";
+ reg = <0x100 0x00000020>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <38 2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ avr@58 {
+ compatible = "ibm,akebono-avr";
+ reg = <0x58>;
+ };
+ };
+
+ FPGA0: fpga@ebc00000 {
+ compatible = "ibm,akebono-fpga";
+ reg = <0xebc00000 0x8>;
+ };
+ };
+
+ PCIE0: pciex@10100000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+ primary;
+ port = <0x0>; /* port number */
+ reg = <0x00000101 0x00000000 0x0 0x10000000 /* Config space access */
+ 0x00000100 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
+ dcr-reg = <0xc0 0x20>;
+
+// pci_space < pci_addr > < cpu_addr > < size >
+ ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000
+ 0x01000000 0x0 0x0 0x00000140 0x0 0x0 0x00010000>;
+
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
+
+ /* This drives busses 0 to 0xf */
+ bus-range = <0x0 0xf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &MPIC 45 0x2 /* int A */
+ 0x0 0x0 0x0 0x2 &MPIC 46 0x2 /* int B */
+ 0x0 0x0 0x0 0x3 &MPIC 47 0x2 /* int C */
+ 0x0 0x0 0x0 0x4 &MPIC 48 0x2 /* int D */>;
+ };
+
+ PCIE1: pciex@20100000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+ primary;
+ port = <0x1>; /* port number */
+ reg = <0x00000201 0x00000000 0x0 0x10000000 /* Config space access */
+ 0x00000200 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
+ dcr-reg = <0x100 0x20>;
+
+// pci_space < pci_addr > < cpu_addr > < size >
+ ranges = <0x02000000 0x00000000 0x80000000 0x00000210 0x80000000 0x0 0x80000000
+ 0x01000000 0x0 0x0 0x00000240 0x0 0x0 0x00010000>;
+
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
+
+ /* This drives busses 0 to 0xf */
+ bus-range = <0x0 0xf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &MPIC 53 0x2 /* int A */
+ 0x0 0x0 0x0 0x2 &MPIC 54 0x2 /* int B */
+ 0x0 0x0 0x0 0x3 &MPIC 55 0x2 /* int C */
+ 0x0 0x0 0x0 0x4 &MPIC 56 0x2 /* int D */>;
+ };
+
+ PCIE2: pciex@18100000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+ primary;
+ port = <0x2>; /* port number */
+ reg = <0x00000181 0x00000000 0x0 0x10000000 /* Config space access */
+ 0x00000180 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
+ dcr-reg = <0xe0 0x20>;
+
+// pci_space < pci_addr > < cpu_addr > < size >
+ ranges = <0x02000000 0x00000000 0x80000000 0x00000190 0x80000000 0x0 0x80000000
+ 0x01000000 0x0 0x0 0x000001c0 0x0 0x0 0x00010000>;
+
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
+
+ /* This drives busses 0 to 0xf */
+ bus-range = <0x0 0xf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &MPIC 61 0x2 /* int A */
+ 0x0 0x0 0x0 0x2 &MPIC 62 0x2 /* int B */
+ 0x0 0x0 0x0 0x3 &MPIC 63 0x2 /* int C */
+ 0x0 0x0 0x0 0x4 &MPIC 64 0x2 /* int D */>;
+ };
+
+ PCIE3: pciex@28100000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+ primary;
+ port = <0x3>; /* port number */
+ reg = <0x00000281 0x00000000 0x0 0x10000000 /* Config space access */
+ 0x00000280 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
+ dcr-reg = <0x120 0x20>;
+
+// pci_space < pci_addr > < cpu_addr > < size >
+ ranges = <0x02000000 0x00000000 0x80000000 0x00000290 0x80000000 0x0 0x80000000
+ 0x01000000 0x0 0x0 0x000002c0 0x0 0x0 0x00010000>;
+
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
+
+ /* This drives busses 0 to 0xf */
+ bus-range = <0x0 0xf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &MPIC 69 0x2 /* int A */
+ 0x0 0x0 0x0 0x2 &MPIC 70 0x2 /* int B */
+ 0x0 0x0 0x0 0x3 &MPIC 71 0x2 /* int C */
+ 0x0 0x0 0x0 0x4 &MPIC 72 0x2 /* int D */>;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &UART0;
+ };
+};