diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-designware-core.h')
| -rw-r--r-- | drivers/i2c/busses/i2c-designware-core.h | 19 |
1 files changed, 13 insertions, 6 deletions
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 8e8854ec9882..347843b4f5dd 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -116,6 +116,7 @@ #define DW_IC_STATUS_RFNE BIT(3) #define DW_IC_STATUS_MASTER_ACTIVITY BIT(5) #define DW_IC_STATUS_SLAVE_ACTIVITY BIT(6) +#define DW_IC_STATUS_MASTER_HOLD_TX_FIFO_EMPTY BIT(7) #define DW_IC_SDA_HOLD_RX_SHIFT 16 #define DW_IC_SDA_HOLD_RX_MASK GENMASK(23, 16) @@ -142,10 +143,10 @@ #define DW_IC_SLAVE 1 /* - * Hardware abort codes from the DW_IC_TX_ABRT_SOURCE register + * Hardware abort codes from the DW_IC_TX_ABRT_SOURCE register. * - * Only expected abort codes are listed here - * refer to the datasheet for the full list + * Only expected abort codes are listed here, + * refer to the datasheet for the full list. */ #define ABRT_7B_ADDR_NOACK 0 #define ABRT_10ADDR1_NOACK 1 @@ -200,7 +201,7 @@ struct reset_control; * @rst: optional reset for the controller * @slave: represent an I2C slave device * @get_clk_rate_khz: callback to retrieve IP specific bus speed - * @cmd_err: run time hadware error code + * @cmd_err: run time hardware error code * @msgs: points to an array of messages currently being transferred * @msgs_num: the number of elements in msgs * @msg_write_idx: the element index of the current tx message in the msgs array @@ -236,11 +237,15 @@ struct reset_control; * @release_lock: function to release a hardware lock on the bus * @semaphore_idx: Index of table with semaphore type attached to the bus. It's * -1 if there is no semaphore. - * @shared_with_punit: true if this bus is shared with the SoCs PUNIT + * @shared_with_punit: true if this bus is shared with the SoC's PUNIT * @init: function to initialize the I2C hardware * @set_sda_hold_time: callback to retrieve IP specific SDA hold timing * @mode: operation mode - DW_IC_MASTER or DW_IC_SLAVE * @rinfo: I²C GPIO recovery information + * @bus_capacitance_pF: bus capacitance in picofarads + * @clk_freq_optimized: if this value is true, it means the hardware reduces + * its internal clock frequency by reducing the internal latency required + * to generate the high period and low period of SCL line. * * HCNT and LCNT parameters can be used if the platform knows more accurate * values than the one computed based only on the input clock frequency. @@ -298,6 +303,8 @@ struct dw_i2c_dev { int (*set_sda_hold_time)(struct dw_i2c_dev *dev); int mode; struct i2c_bus_recovery_info rinfo; + u32 bus_capacitance_pF; + bool clk_freq_optimized; }; #define ACCESS_INTR_MASK BIT(0) @@ -328,7 +335,7 @@ struct i2c_dw_semaphore_callbacks { int i2c_dw_init_regmap(struct dw_i2c_dev *dev); u32 i2c_dw_scl_hcnt(struct dw_i2c_dev *dev, unsigned int reg, u32 ic_clk, - u32 tSYMBOL, u32 tf, int cond, int offset); + u32 tSYMBOL, u32 tf, int offset); u32 i2c_dw_scl_lcnt(struct dw_i2c_dev *dev, unsigned int reg, u32 ic_clk, u32 tLOW, u32 tf, int offset); int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev); |