diff options
Diffstat (limited to 'drivers/ide/setup-pci.c')
| -rw-r--r-- | drivers/ide/setup-pci.c | 682 |
1 files changed, 0 insertions, 682 deletions
diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c deleted file mode 100644 index fdc8e813170c..000000000000 --- a/drivers/ide/setup-pci.c +++ /dev/null @@ -1,682 +0,0 @@ -/* - * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> - * Copyright (C) 1995-1998 Mark Lord - * Copyright (C) 2007-2009 Bartlomiej Zolnierkiewicz - * - * May be copied or modified under the terms of the GNU General Public License - */ - -#include <linux/types.h> -#include <linux/kernel.h> -#include <linux/export.h> -#include <linux/pci.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/ide.h> -#include <linux/dma-mapping.h> - -#include <asm/io.h> - -/** - * ide_setup_pci_baseregs - place a PCI IDE controller native - * @dev: PCI device of interface to switch native - * @name: Name of interface - * - * We attempt to place the PCI interface into PCI native mode. If - * we succeed the BARs are ok and the controller is in PCI mode. - * Returns 0 on success or an errno code. - * - * FIXME: if we program the interface and then fail to set the BARS - * we don't switch it back to legacy mode. Do we actually care ?? - */ - -static int ide_setup_pci_baseregs(struct pci_dev *dev, const char *name) -{ - u8 progif = 0; - - /* - * Place both IDE interfaces into PCI "native" mode: - */ - if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) || - (progif & 5) != 5) { - if ((progif & 0xa) != 0xa) { - printk(KERN_INFO "%s %s: device not capable of full " - "native PCI mode\n", name, pci_name(dev)); - return -EOPNOTSUPP; - } - printk(KERN_INFO "%s %s: placing both ports into native PCI " - "mode\n", name, pci_name(dev)); - (void) pci_write_config_byte(dev, PCI_CLASS_PROG, progif|5); - if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) || - (progif & 5) != 5) { - printk(KERN_ERR "%s %s: rewrite of PROGIF failed, " - "wanted 0x%04x, got 0x%04x\n", - name, pci_name(dev), progif | 5, progif); - return -EOPNOTSUPP; - } - } - return 0; -} - -#ifdef CONFIG_BLK_DEV_IDEDMA_PCI -static int ide_pci_clear_simplex(unsigned long dma_base, const char *name) -{ - u8 dma_stat = inb(dma_base + 2); - - outb(dma_stat & 0x60, dma_base + 2); - dma_stat = inb(dma_base + 2); - - return (dma_stat & 0x80) ? 1 : 0; -} - -/** - * ide_pci_dma_base - setup BMIBA - * @hwif: IDE interface - * @d: IDE port info - * - * Fetch the DMA Bus-Master-I/O-Base-Address (BMIBA) from PCI space. - */ - -unsigned long ide_pci_dma_base(ide_hwif_t *hwif, const struct ide_port_info *d) -{ - struct pci_dev *dev = to_pci_dev(hwif->dev); - unsigned long dma_base = 0; - - if (hwif->host_flags & IDE_HFLAG_MMIO) - return hwif->dma_base; - - if (hwif->mate && hwif->mate->dma_base) { - dma_base = hwif->mate->dma_base - (hwif->channel ? 0 : 8); - } else { - u8 baridx = (d->host_flags & IDE_HFLAG_CS5520) ? 2 : 4; - - dma_base = pci_resource_start(dev, baridx); - - if (dma_base == 0) { - printk(KERN_ERR "%s %s: DMA base is invalid\n", - d->name, pci_name(dev)); - return 0; - } - } - - if (hwif->channel) - dma_base += 8; - - return dma_base; -} -EXPORT_SYMBOL_GPL(ide_pci_dma_base); - -int ide_pci_check_simplex(ide_hwif_t *hwif, const struct ide_port_info *d) -{ - struct pci_dev *dev = to_pci_dev(hwif->dev); - u8 dma_stat; - - if (d->host_flags & (IDE_HFLAG_MMIO | IDE_HFLAG_CS5520)) - goto out; - - if (d->host_flags & IDE_HFLAG_CLEAR_SIMPLEX) { - if (ide_pci_clear_simplex(hwif->dma_base, d->name)) - printk(KERN_INFO "%s %s: simplex device: DMA forced\n", - d->name, pci_name(dev)); - goto out; - } - - /* - * If the device claims "simplex" DMA, this means that only one of - * the two interfaces can be trusted with DMA at any point in time - * (so we should enable DMA only on one of the two interfaces). - * - * FIXME: At this point we haven't probed the drives so we can't make - * the appropriate decision. Really we should defer this problem until - * we tune the drive then try to grab DMA ownership if we want to be - * the DMA end. This has to be become dynamic to handle hot-plug. - */ - dma_stat = hwif->dma_ops->dma_sff_read_status(hwif); - if ((dma_stat & 0x80) && hwif->mate && hwif->mate->dma_base) { - printk(KERN_INFO "%s %s: simplex device: DMA disabled\n", - d->name, pci_name(dev)); - return -1; - } -out: - return 0; -} -EXPORT_SYMBOL_GPL(ide_pci_check_simplex); - -/* - * Set up BM-DMA capability (PnP BIOS should have done this) - */ -int ide_pci_set_master(struct pci_dev *dev, const char *name) -{ - u16 pcicmd; - - pci_read_config_word(dev, PCI_COMMAND, &pcicmd); - - if ((pcicmd & PCI_COMMAND_MASTER) == 0) { - pci_set_master(dev); - - if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) || - (pcicmd & PCI_COMMAND_MASTER) == 0) { - printk(KERN_ERR "%s %s: error updating PCICMD\n", - name, pci_name(dev)); - return -EIO; - } - } - - return 0; -} -EXPORT_SYMBOL_GPL(ide_pci_set_master); -#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ - -void ide_setup_pci_noise(struct pci_dev *dev, const struct ide_port_info *d) -{ - printk(KERN_INFO "%s %s: IDE controller (0x%04x:0x%04x rev 0x%02x)\n", - d->name, pci_name(dev), - dev->vendor, dev->device, dev->revision); -} -EXPORT_SYMBOL_GPL(ide_setup_pci_noise); - - -/** - * ide_pci_enable - do PCI enables - * @dev: PCI device - * @bars: PCI BARs mask - * @d: IDE port info - * - * Enable the IDE PCI device. We attempt to enable the device in full - * but if that fails then we only need IO space. The PCI code should - * have setup the proper resources for us already for controllers in - * legacy mode. - * - * Returns zero on success or an error code - */ - -static int ide_pci_enable(struct pci_dev *dev, int bars, - const struct ide_port_info *d) -{ - int ret; - - if (pci_enable_device(dev)) { - ret = pci_enable_device_io(dev); - if (ret < 0) { - printk(KERN_WARNING "%s %s: couldn't enable device\n", - d->name, pci_name(dev)); - goto out; - } - printk(KERN_WARNING "%s %s: BIOS configuration fixed\n", - d->name, pci_name(dev)); - } - - /* - * assume all devices can do 32-bit DMA for now, we can add - * a DMA mask field to the struct ide_port_info if we need it - * (or let lower level driver set the DMA mask) - */ - ret = dma_set_mask(&dev->dev, DMA_BIT_MASK(32)); - if (ret < 0) { - printk(KERN_ERR "%s %s: can't set DMA mask\n", - d->name, pci_name(dev)); - goto out; - } - - ret = pci_request_selected_regions(dev, bars, d->name); - if (ret < 0) - printk(KERN_ERR "%s %s: can't reserve resources\n", - d->name, pci_name(dev)); -out: - return ret; -} - -/** - * ide_pci_configure - configure an unconfigured device - * @dev: PCI device - * @d: IDE port info - * - * Enable and configure the PCI device we have been passed. - * Returns zero on success or an error code. - */ - -static int ide_pci_configure(struct pci_dev *dev, const struct ide_port_info *d) -{ - u16 pcicmd = 0; - /* - * PnP BIOS was *supposed* to have setup this device, but we - * can do it ourselves, so long as the BIOS has assigned an IRQ - * (or possibly the device is using a "legacy header" for IRQs). - * Maybe the user deliberately *disabled* the device, - * but we'll eventually ignore it again if no drives respond. - */ - if (ide_setup_pci_baseregs(dev, d->name) || - pci_write_config_word(dev, PCI_COMMAND, pcicmd | PCI_COMMAND_IO)) { - printk(KERN_INFO "%s %s: device disabled (BIOS)\n", - d->name, pci_name(dev)); - return -ENODEV; - } - if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd)) { - printk(KERN_ERR "%s %s: error accessing PCI regs\n", - d->name, pci_name(dev)); - return -EIO; - } - if (!(pcicmd & PCI_COMMAND_IO)) { - printk(KERN_ERR "%s %s: unable to enable IDE controller\n", - d->name, pci_name(dev)); - return -ENXIO; - } - return 0; -} - -/** - * ide_pci_check_iomem - check a register is I/O - * @dev: PCI device - * @d: IDE port info - * @bar: BAR number - * - * Checks if a BAR is configured and points to MMIO space. If so, - * return an error code. Otherwise return 0 - */ - -static int ide_pci_check_iomem(struct pci_dev *dev, const struct ide_port_info *d, - int bar) -{ - ulong flags = pci_resource_flags(dev, bar); - - /* Unconfigured ? */ - if (!flags || pci_resource_len(dev, bar) == 0) - return 0; - - /* I/O space */ - if (flags & IORESOURCE_IO) - return 0; - - /* Bad */ - return -EINVAL; -} - -/** - * ide_hw_configure - configure a struct ide_hw instance - * @dev: PCI device holding interface - * @d: IDE port info - * @port: port number - * @hw: struct ide_hw instance corresponding to this port - * - * Perform the initial set up for the hardware interface structure. This - * is done per interface port rather than per PCI device. There may be - * more than one port per device. - * - * Returns zero on success or an error code. - */ - -static int ide_hw_configure(struct pci_dev *dev, const struct ide_port_info *d, - unsigned int port, struct ide_hw *hw) -{ - unsigned long ctl = 0, base = 0; - - if ((d->host_flags & IDE_HFLAG_ISA_PORTS) == 0) { - if (ide_pci_check_iomem(dev, d, 2 * port) || - ide_pci_check_iomem(dev, d, 2 * port + 1)) { - printk(KERN_ERR "%s %s: I/O baseregs (BIOS) are " - "reported as MEM for port %d!\n", - d->name, pci_name(dev), port); - return -EINVAL; - } - - ctl = pci_resource_start(dev, 2*port+1); - base = pci_resource_start(dev, 2*port); - } else { - /* Use default values */ - ctl = port ? 0x374 : 0x3f4; - base = port ? 0x170 : 0x1f0; - } - - if (!base || !ctl) { - printk(KERN_ERR "%s %s: bad PCI BARs for port %d, skipping\n", - d->name, pci_name(dev), port); - return -EINVAL; - } - - memset(hw, 0, sizeof(*hw)); - hw->dev = &dev->dev; - ide_std_init_ports(hw, base, ctl | 2); - - return 0; -} - -#ifdef CONFIG_BLK_DEV_IDEDMA_PCI -/** - * ide_hwif_setup_dma - configure DMA interface - * @hwif: IDE interface - * @d: IDE port info - * - * Set up the DMA base for the interface. Enable the master bits as - * necessary and attempt to bring the device DMA into a ready to use - * state - */ - -int ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d) -{ - struct pci_dev *dev = to_pci_dev(hwif->dev); - - if ((d->host_flags & IDE_HFLAG_NO_AUTODMA) == 0 || - ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && - (dev->class & 0x80))) { - unsigned long base = ide_pci_dma_base(hwif, d); - - if (base == 0) - return -1; - - hwif->dma_base = base; - - if (hwif->dma_ops == NULL) - hwif->dma_ops = &sff_dma_ops; - - if (ide_pci_check_simplex(hwif, d) < 0) - return -1; - - if (ide_pci_set_master(dev, d->name) < 0) - return -1; - - if (hwif->host_flags & IDE_HFLAG_MMIO) - printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name); - else - printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n", - hwif->name, base, base + 7); - - hwif->extra_base = base + (hwif->channel ? 8 : 16); - - if (ide_allocate_dma_engine(hwif)) - return -1; - } - - return 0; -} -#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ - -/** - * ide_setup_pci_controller - set up IDE PCI - * @dev: PCI device - * @bars: PCI BARs mask - * @d: IDE port info - * @noisy: verbose flag - * - * Set up the PCI and controller side of the IDE interface. This brings - * up the PCI side of the device, checks that the device is enabled - * and enables it if need be - */ - -static int ide_setup_pci_controller(struct pci_dev *dev, int bars, - const struct ide_port_info *d, int noisy) -{ - int ret; - u16 pcicmd; - - if (noisy) - ide_setup_pci_noise(dev, d); - - ret = ide_pci_enable(dev, bars, d); - if (ret < 0) - goto out; - - ret = pci_read_config_word(dev, PCI_COMMAND, &pcicmd); - if (ret < 0) { - printk(KERN_ERR "%s %s: error accessing PCI regs\n", - d->name, pci_name(dev)); - goto out_free_bars; - } - if (!(pcicmd & PCI_COMMAND_IO)) { /* is device disabled? */ - ret = ide_pci_configure(dev, d); - if (ret < 0) - goto out_free_bars; - printk(KERN_INFO "%s %s: device enabled (Linux)\n", - d->name, pci_name(dev)); - } - - goto out; - -out_free_bars: - pci_release_selected_regions(dev, bars); -out: - return ret; -} - -/** - * ide_pci_setup_ports - configure ports/devices on PCI IDE - * @dev: PCI device - * @d: IDE port info - * @hw: struct ide_hw instances corresponding to this PCI IDE device - * @hws: struct ide_hw pointers table to update - * - * Scan the interfaces attached to this device and do any - * necessary per port setup. Attach the devices and ask the - * generic DMA layer to do its work for us. - * - * Normally called automaticall from do_ide_pci_setup_device, - * but is also used directly as a helper function by some controllers - * where the chipset setup is not the default PCI IDE one. - */ - -void ide_pci_setup_ports(struct pci_dev *dev, const struct ide_port_info *d, - struct ide_hw *hw, struct ide_hw **hws) -{ - int channels = (d->host_flags & IDE_HFLAG_SINGLE) ? 1 : 2, port; - u8 tmp; - - /* - * Set up the IDE ports - */ - - for (port = 0; port < channels; ++port) { - const struct ide_pci_enablebit *e = &d->enablebits[port]; - - if (e->reg && (pci_read_config_byte(dev, e->reg, &tmp) || - (tmp & e->mask) != e->val)) { - printk(KERN_INFO "%s %s: IDE port disabled\n", - d->name, pci_name(dev)); - continue; /* port not enabled */ - } - - if (ide_hw_configure(dev, d, port, hw + port)) - continue; - - *(hws + port) = hw + port; - } -} -EXPORT_SYMBOL_GPL(ide_pci_setup_ports); - -/* - * ide_setup_pci_device() looks at the primary/secondary interfaces - * on a PCI IDE device and, if they are enabled, prepares the IDE driver - * for use with them. This generic code works for most PCI chipsets. - * - * One thing that is not standardized is the location of the - * primary/secondary interface "enable/disable" bits. For chipsets that - * we "know" about, this information is in the struct ide_port_info; - * for all other chipsets, we just assume both interfaces are enabled. - */ -static int do_ide_setup_pci_device(struct pci_dev *dev, - const struct ide_port_info *d, - u8 noisy) -{ - int pciirq, ret; - - /* - * Can we trust the reported IRQ? - */ - pciirq = dev->irq; - - /* - * This allows offboard ide-pci cards the enable a BIOS, - * verify interrupt settings of split-mirror pci-config - * space, place chipset into init-mode, and/or preserve - * an interrupt if the card is not native ide support. - */ - ret = d->init_chipset ? d->init_chipset(dev) : 0; - if (ret < 0) - goto out; - - if (ide_pci_is_in_compatibility_mode(dev)) { - if (noisy) - printk(KERN_INFO "%s %s: not 100%% native mode: will " - "probe irqs later\n", d->name, pci_name(dev)); - pciirq = 0; - } else if (!pciirq && noisy) { - printk(KERN_WARNING "%s %s: bad irq (%d): will probe later\n", - d->name, pci_name(dev), pciirq); - } else if (noisy) { - printk(KERN_INFO "%s %s: 100%% native mode on irq %d\n", - d->name, pci_name(dev), pciirq); - } - - ret = pciirq; -out: - return ret; -} - -int ide_pci_init_two(struct pci_dev *dev1, struct pci_dev *dev2, - const struct ide_port_info *d, void *priv) -{ - struct pci_dev *pdev[] = { dev1, dev2 }; - struct ide_host *host; - int ret, i, n_ports = dev2 ? 4 : 2, bars; - struct ide_hw hw[4], *hws[] = { NULL, NULL, NULL, NULL }; - - if (d->host_flags & IDE_HFLAG_SINGLE) - bars = (1 << 2) - 1; - else - bars = (1 << 4) - 1; - - if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0) { - if (d->host_flags & IDE_HFLAG_CS5520) - bars |= (1 << 2); - else - bars |= (1 << 4); - } - - for (i = 0; i < n_ports / 2; i++) { - ret = ide_setup_pci_controller(pdev[i], bars, d, !i); - if (ret < 0) { - if (i == 1) - pci_release_selected_regions(pdev[0], bars); - goto out; - } - - ide_pci_setup_ports(pdev[i], d, &hw[i*2], &hws[i*2]); - } - - host = ide_host_alloc(d, hws, n_ports); - if (host == NULL) { - ret = -ENOMEM; - goto out_free_bars; - } - - host->dev[0] = &dev1->dev; - if (dev2) - host->dev[1] = &dev2->dev; - - host->host_priv = priv; - host->irq_flags = IRQF_SHARED; - - pci_set_drvdata(pdev[0], host); - if (dev2) - pci_set_drvdata(pdev[1], host); - - for (i = 0; i < n_ports / 2; i++) { - ret = do_ide_setup_pci_device(pdev[i], d, !i); - - /* - * FIXME: Mom, mom, they stole me the helper function to undo - * do_ide_setup_pci_device() on the first device! - */ - if (ret < 0) - goto out_free_bars; - - /* fixup IRQ */ - if (ide_pci_is_in_compatibility_mode(pdev[i])) { - hw[i*2].irq = pci_get_legacy_ide_irq(pdev[i], 0); - hw[i*2 + 1].irq = pci_get_legacy_ide_irq(pdev[i], 1); - } else - hw[i*2 + 1].irq = hw[i*2].irq = ret; - } - - ret = ide_host_register(host, d, hws); - if (ret) - ide_host_free(host); - else - goto out; - -out_free_bars: - i = n_ports / 2; - while (i--) - pci_release_selected_regions(pdev[i], bars); -out: - return ret; -} -EXPORT_SYMBOL_GPL(ide_pci_init_two); - -int ide_pci_init_one(struct pci_dev *dev, const struct ide_port_info *d, - void *priv) -{ - return ide_pci_init_two(dev, NULL, d, priv); -} -EXPORT_SYMBOL_GPL(ide_pci_init_one); - -void ide_pci_remove(struct pci_dev *dev) -{ - struct ide_host *host = pci_get_drvdata(dev); - struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL; - int bars; - - if (host->host_flags & IDE_HFLAG_SINGLE) - bars = (1 << 2) - 1; - else - bars = (1 << 4) - 1; - - if ((host->host_flags & IDE_HFLAG_NO_DMA) == 0) { - if (host->host_flags & IDE_HFLAG_CS5520) - bars |= (1 << 2); - else - bars |= (1 << 4); - } - - ide_host_remove(host); - - if (dev2) - pci_release_selected_regions(dev2, bars); - pci_release_selected_regions(dev, bars); - - if (dev2) - pci_disable_device(dev2); - pci_disable_device(dev); -} -EXPORT_SYMBOL_GPL(ide_pci_remove); - -#ifdef CONFIG_PM -int ide_pci_suspend(struct pci_dev *dev, pm_message_t state) -{ - pci_save_state(dev); - pci_disable_device(dev); - pci_set_power_state(dev, pci_choose_state(dev, state)); - - return 0; -} -EXPORT_SYMBOL_GPL(ide_pci_suspend); - -int ide_pci_resume(struct pci_dev *dev) -{ - struct ide_host *host = pci_get_drvdata(dev); - int rc; - - pci_set_power_state(dev, PCI_D0); - - rc = pci_enable_device(dev); - if (rc) - return rc; - - pci_restore_state(dev); - pci_set_master(dev); - - if (host->init_chipset) - host->init_chipset(dev); - - return 0; -} -EXPORT_SYMBOL_GPL(ide_pci_resume); -#endif |