diff options
Diffstat (limited to 'drivers/net/dsa/microchip/ksz_common.c')
-rw-r--r-- | drivers/net/dsa/microchip/ksz_common.c | 273 |
1 files changed, 265 insertions, 8 deletions
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c index 173ad8f04671..3fed406fb46a 100644 --- a/drivers/net/dsa/microchip/ksz_common.c +++ b/drivers/net/dsa/microchip/ksz_common.c @@ -16,6 +16,7 @@ #include <linux/etherdevice.h> #include <linux/if_bridge.h> #include <linux/if_vlan.h> +#include <linux/if_hsr.h> #include <linux/irq.h> #include <linux/irqdomain.h> #include <linux/of.h> @@ -318,6 +319,9 @@ static const struct ksz_dev_ops ksz9477_dev_ops = { .mdb_del = ksz9477_mdb_del, .change_mtu = ksz9477_change_mtu, .phylink_mac_link_up = ksz9477_phylink_mac_link_up, + .get_wol = ksz9477_get_wol, + .set_wol = ksz9477_set_wol, + .wol_pre_shutdown = ksz9477_wol_pre_shutdown, .config_cpu_port = ksz9477_config_cpu_port, .tc_cbs_set_cinc = ksz9477_tc_cbs_set_cinc, .enable_stp_addr = ksz9477_enable_stp_addr, @@ -364,6 +368,7 @@ static const struct ksz_dev_ops lan937x_dev_ops = { }; static const u16 ksz8795_regs[] = { + [REG_SW_MAC_ADDR] = 0x68, [REG_IND_CTRL_0] = 0x6E, [REG_IND_DATA_8] = 0x70, [REG_IND_DATA_CHECK] = 0x72, @@ -439,6 +444,7 @@ static const u8 ksz8795_shifts[] = { }; static const u16 ksz8863_regs[] = { + [REG_SW_MAC_ADDR] = 0x70, [REG_IND_CTRL_0] = 0x79, [REG_IND_DATA_8] = 0x7B, [REG_IND_DATA_CHECK] = 0x7B, @@ -492,6 +498,7 @@ static u8 ksz8863_shifts[] = { }; static const u16 ksz9477_regs[] = { + [REG_SW_MAC_ADDR] = 0x0302, [P_STP_CTRL] = 0x0B04, [S_START_CTRL] = 0x0300, [S_BROADCAST_CTRL] = 0x0332, @@ -1942,14 +1949,14 @@ static int ksz_irq_phy_setup(struct ksz_device *dev) ret = irq; goto out; } - ds->slave_mii_bus->irq[phy] = irq; + ds->user_mii_bus->irq[phy] = irq; } } return 0; out: while (phy--) if (BIT(phy) & ds->phys_mii_mask) - irq_dispose_mapping(ds->slave_mii_bus->irq[phy]); + irq_dispose_mapping(ds->user_mii_bus->irq[phy]); return ret; } @@ -1961,7 +1968,7 @@ static void ksz_irq_phy_free(struct ksz_device *dev) for (phy = 0; phy < KSZ_MAX_NUM_PORTS; phy++) if (BIT(phy) & ds->phys_mii_mask) - irq_dispose_mapping(ds->slave_mii_bus->irq[phy]); + irq_dispose_mapping(ds->user_mii_bus->irq[phy]); } static int ksz_mdio_register(struct ksz_device *dev) @@ -1984,12 +1991,12 @@ static int ksz_mdio_register(struct ksz_device *dev) bus->priv = dev; bus->read = ksz_sw_mdio_read; bus->write = ksz_sw_mdio_write; - bus->name = "ksz slave smi"; + bus->name = "ksz user smi"; snprintf(bus->id, MII_BUS_ID_SIZE, "SMI-%d", ds->index); bus->parent = ds->dev; bus->phy_mask = ~ds->phys_mii_mask; - ds->slave_mii_bus = bus; + ds->user_mii_bus = bus; if (dev->irq > 0) { ret = ksz_irq_phy_setup(dev); @@ -2341,7 +2348,7 @@ static void ksz_mib_read_work(struct work_struct *work) if (!p->read) { const struct dsa_port *dp = dsa_to_port(dev->ds, i); - if (!netif_carrier_ok(dp->slave)) + if (!netif_carrier_ok(dp->user)) mib->cnt_ptr = dev->info->reg_mib_cnt; } port_r_cnt(dev, i); @@ -2461,7 +2468,7 @@ static void ksz_get_ethtool_stats(struct dsa_switch *ds, int port, mutex_lock(&mib->cnt_mutex); /* Only read dropped counters if no link. */ - if (!netif_carrier_ok(dp->slave)) + if (!netif_carrier_ok(dp->user)) mib->cnt_ptr = dev->info->reg_mib_cnt; port_r_cnt(dev, port); memcpy(buf, mib->counters, dev->info->mib_cnt * sizeof(u64)); @@ -2571,7 +2578,7 @@ static int ksz_port_setup(struct dsa_switch *ds, int port) if (!dsa_is_user_port(ds, port)) return 0; - /* setup slave port */ + /* setup user port */ dev->dev_ops->port_setup(dev, port, false); /* port_stp_state_set() will be called after to enable the port so @@ -3539,6 +3546,224 @@ static int ksz_setup_tc(struct dsa_switch *ds, int port, } } +static void ksz_get_wol(struct dsa_switch *ds, int port, + struct ethtool_wolinfo *wol) +{ + struct ksz_device *dev = ds->priv; + + if (dev->dev_ops->get_wol) + dev->dev_ops->get_wol(dev, port, wol); +} + +static int ksz_set_wol(struct dsa_switch *ds, int port, + struct ethtool_wolinfo *wol) +{ + struct ksz_device *dev = ds->priv; + + if (dev->dev_ops->set_wol) + return dev->dev_ops->set_wol(dev, port, wol); + + return -EOPNOTSUPP; +} + +static int ksz_port_set_mac_address(struct dsa_switch *ds, int port, + const unsigned char *addr) +{ + struct dsa_port *dp = dsa_to_port(ds, port); + struct ethtool_wolinfo wol; + + if (dp->hsr_dev) { + dev_err(ds->dev, + "Cannot change MAC address on port %d with active HSR offload\n", + port); + return -EBUSY; + } + + ksz_get_wol(ds, dp->index, &wol); + if (wol.wolopts & WAKE_MAGIC) { + dev_err(ds->dev, + "Cannot change MAC address on port %d with active Wake on Magic Packet\n", + port); + return -EBUSY; + } + + return 0; +} + +/** + * ksz_is_port_mac_global_usable - Check if the MAC address on a given port + * can be used as a global address. + * @ds: Pointer to the DSA switch structure. + * @port: The port number on which the MAC address is to be checked. + * + * This function examines the MAC address set on the specified port and + * determines if it can be used as a global address for the switch. + * + * Return: true if the port's MAC address can be used as a global address, false + * otherwise. + */ +bool ksz_is_port_mac_global_usable(struct dsa_switch *ds, int port) +{ + struct net_device *user = dsa_to_port(ds, port)->user; + const unsigned char *addr = user->dev_addr; + struct ksz_switch_macaddr *switch_macaddr; + struct ksz_device *dev = ds->priv; + + ASSERT_RTNL(); + + switch_macaddr = dev->switch_macaddr; + if (switch_macaddr && !ether_addr_equal(switch_macaddr->addr, addr)) + return false; + + return true; +} + +/** + * ksz_switch_macaddr_get - Program the switch's MAC address register. + * @ds: DSA switch instance. + * @port: Port number. + * @extack: Netlink extended acknowledgment. + * + * This function programs the switch's MAC address register with the MAC address + * of the requesting user port. This single address is used by the switch for + * multiple features like HSR self-address filtering and WoL. Other user ports + * can share ownership of this address as long as their MAC address is the same. + * The MAC addresses of user ports must not change while they have ownership of + * the switch MAC address. + * + * Return: 0 on success, or other error codes on failure. + */ +int ksz_switch_macaddr_get(struct dsa_switch *ds, int port, + struct netlink_ext_ack *extack) +{ + struct net_device *user = dsa_to_port(ds, port)->user; + const unsigned char *addr = user->dev_addr; + struct ksz_switch_macaddr *switch_macaddr; + struct ksz_device *dev = ds->priv; + const u16 *regs = dev->info->regs; + int i, ret; + + /* Make sure concurrent MAC address changes are blocked */ + ASSERT_RTNL(); + + switch_macaddr = dev->switch_macaddr; + if (switch_macaddr) { + if (!ether_addr_equal(switch_macaddr->addr, addr)) { + NL_SET_ERR_MSG_FMT_MOD(extack, + "Switch already configured for MAC address %pM", + switch_macaddr->addr); + return -EBUSY; + } + + refcount_inc(&switch_macaddr->refcount); + return 0; + } + + switch_macaddr = kzalloc(sizeof(*switch_macaddr), GFP_KERNEL); + if (!switch_macaddr) + return -ENOMEM; + + ether_addr_copy(switch_macaddr->addr, addr); + refcount_set(&switch_macaddr->refcount, 1); + dev->switch_macaddr = switch_macaddr; + + /* Program the switch MAC address to hardware */ + for (i = 0; i < ETH_ALEN; i++) { + ret = ksz_write8(dev, regs[REG_SW_MAC_ADDR] + i, addr[i]); + if (ret) + goto macaddr_drop; + } + + return 0; + +macaddr_drop: + dev->switch_macaddr = NULL; + refcount_set(&switch_macaddr->refcount, 0); + kfree(switch_macaddr); + + return ret; +} + +void ksz_switch_macaddr_put(struct dsa_switch *ds) +{ + struct ksz_switch_macaddr *switch_macaddr; + struct ksz_device *dev = ds->priv; + const u16 *regs = dev->info->regs; + int i; + + /* Make sure concurrent MAC address changes are blocked */ + ASSERT_RTNL(); + + switch_macaddr = dev->switch_macaddr; + if (!refcount_dec_and_test(&switch_macaddr->refcount)) + return; + + for (i = 0; i < ETH_ALEN; i++) + ksz_write8(dev, regs[REG_SW_MAC_ADDR] + i, 0); + + dev->switch_macaddr = NULL; + kfree(switch_macaddr); +} + +static int ksz_hsr_join(struct dsa_switch *ds, int port, struct net_device *hsr, + struct netlink_ext_ack *extack) +{ + struct ksz_device *dev = ds->priv; + enum hsr_version ver; + int ret; + + ret = hsr_get_version(hsr, &ver); + if (ret) + return ret; + + if (dev->chip_id != KSZ9477_CHIP_ID) { + NL_SET_ERR_MSG_MOD(extack, "Chip does not support HSR offload"); + return -EOPNOTSUPP; + } + + /* KSZ9477 can support HW offloading of only 1 HSR device */ + if (dev->hsr_dev && hsr != dev->hsr_dev) { + NL_SET_ERR_MSG_MOD(extack, "Offload supported for a single HSR"); + return -EOPNOTSUPP; + } + + /* KSZ9477 only supports HSR v0 and v1 */ + if (!(ver == HSR_V0 || ver == HSR_V1)) { + NL_SET_ERR_MSG_MOD(extack, "Only HSR v0 and v1 supported"); + return -EOPNOTSUPP; + } + + /* Self MAC address filtering, to avoid frames traversing + * the HSR ring more than once. + */ + ret = ksz_switch_macaddr_get(ds, port, extack); + if (ret) + return ret; + + ksz9477_hsr_join(ds, port, hsr); + dev->hsr_dev = hsr; + dev->hsr_ports |= BIT(port); + + return 0; +} + +static int ksz_hsr_leave(struct dsa_switch *ds, int port, + struct net_device *hsr) +{ + struct ksz_device *dev = ds->priv; + + WARN_ON(dev->chip_id != KSZ9477_CHIP_ID); + + ksz9477_hsr_leave(ds, port, hsr); + dev->hsr_ports &= ~BIT(port); + if (!dev->hsr_ports) + dev->hsr_dev = NULL; + + ksz_switch_macaddr_put(ds); + + return 0; +} + static const struct dsa_switch_ops ksz_switch_ops = { .get_tag_protocol = ksz_get_tag_protocol, .connect_tag_protocol = ksz_connect_tag_protocol, @@ -3558,6 +3783,9 @@ static const struct dsa_switch_ops ksz_switch_ops = { .get_sset_count = ksz_sset_count, .port_bridge_join = ksz_port_bridge_join, .port_bridge_leave = ksz_port_bridge_leave, + .port_hsr_join = ksz_hsr_join, + .port_hsr_leave = ksz_hsr_leave, + .port_set_mac_address = ksz_port_set_mac_address, .port_stp_state_set = ksz_port_stp_state_set, .port_teardown = ksz_port_teardown, .port_pre_bridge_flags = ksz_port_pre_bridge_flags, @@ -3577,6 +3805,8 @@ static const struct dsa_switch_ops ksz_switch_ops = { .get_pause_stats = ksz_get_pause_stats, .port_change_mtu = ksz_change_mtu, .port_max_mtu = ksz_max_mtu, + .get_wol = ksz_get_wol, + .set_wol = ksz_set_wol, .get_ts_info = ksz_get_ts_info, .port_hwtstamp_get = ksz_hwtstamp_get, .port_hwtstamp_set = ksz_hwtstamp_set, @@ -3616,6 +3846,30 @@ struct ksz_device *ksz_switch_alloc(struct device *base, void *priv) } EXPORT_SYMBOL(ksz_switch_alloc); +/** + * ksz_switch_shutdown - Shutdown routine for the switch device. + * @dev: The switch device structure. + * + * This function is responsible for initiating a shutdown sequence for the + * switch device. It invokes the reset operation defined in the device + * operations, if available, to reset the switch. Subsequently, it calls the + * DSA framework's shutdown function to ensure a proper shutdown of the DSA + * switch. + */ +void ksz_switch_shutdown(struct ksz_device *dev) +{ + bool wol_enabled = false; + + if (dev->dev_ops->wol_pre_shutdown) + dev->dev_ops->wol_pre_shutdown(dev, &wol_enabled); + + if (dev->dev_ops->reset && !wol_enabled) + dev->dev_ops->reset(dev); + + dsa_switch_shutdown(dev->ds); +} +EXPORT_SYMBOL(ksz_switch_shutdown); + static void ksz_parse_rgmii_delay(struct ksz_device *dev, int port_num, struct device_node *port_dn) { @@ -4009,6 +4263,9 @@ int ksz_switch_register(struct ksz_device *dev) dev_err(dev->dev, "inconsistent synclko settings\n"); return -EINVAL; } + + dev->wakeup_source = of_property_read_bool(dev->dev->of_node, + "wakeup-source"); } ret = dsa_register_switch(dev->ds); |