diff options
Diffstat (limited to 'drivers/net/ethernet/intel/ixgbe/ixgbe_common.c')
| -rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 177 |
1 files changed, 132 insertions, 45 deletions
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 77d3039283f6..c38d50c1fcf7 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -100,6 +100,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) case IXGBE_DEV_ID_X550T1: case IXGBE_DEV_ID_X550EM_X_10G_T: case IXGBE_DEV_ID_X550EM_A_10G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T_L: supported = true; break; default: @@ -298,10 +300,12 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); IXGBE_WRITE_FLUSH(hw); - /* Setup flow control */ - ret_val = hw->mac.ops.setup_fc(hw); - if (ret_val) - return ret_val; + /* Setup flow control if method for doing so */ + if (hw->mac.ops.setup_fc) { + ret_val = hw->mac.ops.setup_fc(hw); + if (ret_val) + return ret_val; + } /* Cashe bit indicating need for crosstalk fix */ switch (hw->mac.type) { @@ -346,7 +350,7 @@ s32 ixgbe_start_hw_gen2(struct ixgbe_hw *hw) } IXGBE_WRITE_FLUSH(hw); -#ifndef CONFIG_SPARC +#ifndef CONFIG_ARCH_WANT_RELAX_ORDER /* Disable relaxed ordering */ for (i = 0; i < hw->mac.max_tx_queues; i++) { u32 regval; @@ -390,6 +394,9 @@ s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) status = hw->mac.ops.start_hw(hw); } + /* Initialize the LED link active for LED blink support */ + hw->mac.ops.init_led_link_act(hw); + return status; } @@ -773,6 +780,49 @@ s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) } /** + * ixgbe_init_led_link_act_generic - Store the LED index link/activity. + * @hw: pointer to hardware structure + * + * Store the index for the link active LED. This will be used to support + * blinking the LED. + **/ +s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw) +{ + struct ixgbe_mac_info *mac = &hw->mac; + u32 led_reg, led_mode; + u16 i; + + led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + /* Get LED link active from the LEDCTL register */ + for (i = 0; i < 4; i++) { + led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i); + + if ((led_mode & IXGBE_LED_MODE_MASK_BASE) == + IXGBE_LED_LINK_ACTIVE) { + mac->led_link_act = i; + return 0; + } + } + + /* If LEDCTL register does not have the LED link active set, then use + * known MAC defaults. + */ + switch (hw->mac.type) { + case ixgbe_mac_x550em_a: + mac->led_link_act = 0; + break; + case ixgbe_mac_X550EM_x: + mac->led_link_act = 1; + break; + default: + mac->led_link_act = 2; + } + + return 0; +} + +/** * ixgbe_led_on_generic - Turns on the software controllable LEDs. * @hw: pointer to hardware structure * @index: led number to turn on @@ -2127,7 +2177,7 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) } /* Negotiate the fc mode to use */ - ixgbe_fc_autoneg(hw); + hw->mac.ops.fc_autoneg(hw); /* Disable any previous flow control settings */ mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); @@ -2231,8 +2281,8 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) * Find the intersection between advertised settings and link partner's * advertised settings **/ -static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, - u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) +s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, + u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) { if ((!(adv_reg)) || (!(lp_reg))) return IXGBE_ERR_FC_NOT_NEGOTIATED; @@ -3334,6 +3384,13 @@ s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed, else *speed = IXGBE_LINK_SPEED_100_FULL; break; + case IXGBE_LINKS_SPEED_10_X550EM_A: + *speed = IXGBE_LINK_SPEED_UNKNOWN; + if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T || + hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) { + *speed = IXGBE_LINK_SPEED_10_FULL; + } + break; default: *speed = IXGBE_LINK_SPEED_UNKNOWN; } @@ -3530,7 +3587,7 @@ void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, * Calculates the checksum for some buffer on a specified length. The * checksum calculated is returned. **/ -static u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) +u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) { u32 i; u8 sum = 0; @@ -3545,43 +3602,29 @@ static u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) } /** - * ixgbe_host_interface_command - Issue command to manageability block + * ixgbe_hic_unlocked - Issue command to manageability block unlocked * @hw: pointer to the HW structure - * @buffer: contains the command to write and where the return status will - * be placed + * @buffer: command to write and where the return status will be placed * @length: length of buffer, must be multiple of 4 bytes * @timeout: time in ms to wait for command completion - * @return_data: read and return data from the buffer (true) or not (false) - * Needed because FW structures are big endian and decoding of - * these fields can be 8 bit or 16 bit based on command. Decoding - * is not easily understood without making a table of commands. - * So we will leave this up to the caller to read back the data - * in these cases. * - * Communicates with the manageability block. On success return 0 - * else return IXGBE_ERR_HOST_INTERFACE_COMMAND. + * Communicates with the manageability block. On success return 0 + * else returns semaphore error when encountering an error acquiring + * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. + * + * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held + * by the caller. **/ -s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, - u32 length, u32 timeout, - bool return_data) +s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length, + u32 timeout) { - u32 hdr_size = sizeof(struct ixgbe_hic_hdr); - u32 hicr, i, bi, fwsts; - u16 buf_len, dword_len; - union { - struct ixgbe_hic_hdr hdr; - u32 u32arr[1]; - } *bp = buffer; - s32 status; + u32 hicr, i, fwsts; + u16 dword_len; if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length); return IXGBE_ERR_HOST_INTERFACE_COMMAND; } - /* Take management host interface semaphore */ - status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); - if (status) - return status; /* Set bit 9 of FWSTS clearing FW reset indication */ fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS); @@ -3591,15 +3634,13 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, hicr = IXGBE_READ_REG(hw, IXGBE_HICR); if (!(hicr & IXGBE_HICR_EN)) { hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n"); - status = IXGBE_ERR_HOST_INTERFACE_COMMAND; - goto rel_out; + return IXGBE_ERR_HOST_INTERFACE_COMMAND; } /* Calculate length in DWORDs. We must be DWORD aligned */ if (length % sizeof(u32)) { hw_dbg(hw, "Buffer length failure, not aligned to dword"); - status = IXGBE_ERR_INVALID_ARGUMENT; - goto rel_out; + return IXGBE_ERR_INVALID_ARGUMENT; } dword_len = length >> 2; @@ -3609,7 +3650,7 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, */ for (i = 0; i < dword_len; i++) IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG, - i, cpu_to_le32(bp->u32arr[i])); + i, cpu_to_le32(buffer[i])); /* Setting this bit tells the ARC that a new command is pending. */ IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C); @@ -3623,11 +3664,54 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, /* Check command successful completion. */ if ((timeout && i == timeout) || - !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) { - hw_dbg(hw, "Command has failed with no status valid.\n"); - status = IXGBE_ERR_HOST_INTERFACE_COMMAND; - goto rel_out; + !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) + return IXGBE_ERR_HOST_INTERFACE_COMMAND; + + return 0; +} + +/** + * ixgbe_host_interface_command - Issue command to manageability block + * @hw: pointer to the HW structure + * @buffer: contains the command to write and where the return status will + * be placed + * @length: length of buffer, must be multiple of 4 bytes + * @timeout: time in ms to wait for command completion + * @return_data: read and return data from the buffer (true) or not (false) + * Needed because FW structures are big endian and decoding of + * these fields can be 8 bit or 16 bit based on command. Decoding + * is not easily understood without making a table of commands. + * So we will leave this up to the caller to read back the data + * in these cases. + * + * Communicates with the manageability block. On success return 0 + * else return IXGBE_ERR_HOST_INTERFACE_COMMAND. + **/ +s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, + u32 length, u32 timeout, + bool return_data) +{ + u32 hdr_size = sizeof(struct ixgbe_hic_hdr); + union { + struct ixgbe_hic_hdr hdr; + u32 u32arr[1]; + } *bp = buffer; + u16 buf_len, dword_len; + s32 status; + u32 bi; + + if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { + hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length); + return IXGBE_ERR_HOST_INTERFACE_COMMAND; } + /* Take management host interface semaphore */ + status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); + if (status) + return status; + + status = ixgbe_hic_unlocked(hw, buffer, length, timeout); + if (status) + goto rel_out; if (!return_data) goto rel_out; @@ -3674,6 +3758,8 @@ rel_out: * @min: driver version minor number * @build: driver version build number * @sub: driver version sub build number + * @len: length of driver_ver string + * @driver_ver: driver string * * Sends driver version number to firmware through the manageability * block. On success return 0 @@ -3681,7 +3767,8 @@ rel_out: * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. **/ s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min, - u8 build, u8 sub) + u8 build, u8 sub, __always_unused u16 len, + __always_unused const char *driver_ver) { struct ixgbe_hic_drv_info fw_cmd; int i; |