1 files changed, 41 insertions, 3 deletions

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index d27af65eb08a..89a4dc8ebf94 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2629,10 +2629,38 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
 {
 	u32			reg;
 	u32			timeout = 2000;
+	u32			saved_config = 0;
 
 	if (pm_runtime_suspended(dwc->dev))
 		return 0;
 
+	/*
+	 * When operating in USB 2.0 speeds (HS/FS), ensure that
+	 * GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
+	 * or stopping the controller. This resolves timeout issues that occur
+	 * during frequent role switches between host and device modes.
+	 *
+	 * Save and clear these settings, then restore them after completing the
+	 * controller start or stop sequence.
+	 *
+	 * This solution was discovered through experimentation as it is not
+	 * mentioned in the dwc3 programming guide. It has been tested on an
+	 * Exynos platforms.
+	 */
+	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+	if (reg & DWC3_GUSB2PHYCFG_SUSPHY) {
+		saved_config |= DWC3_GUSB2PHYCFG_SUSPHY;
+		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
+	}
+
+	if (reg & DWC3_GUSB2PHYCFG_ENBLSLPM) {
+		saved_config |= DWC3_GUSB2PHYCFG_ENBLSLPM;
+		reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
+	}
+
+	if (saved_config)
+		dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	if (is_on) {
 		if (DWC3_VER_IS_WITHIN(DWC3, ANY, 187A)) {
@@ -2660,6 +2688,12 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
 		reg &= DWC3_DSTS_DEVCTRLHLT;
 	} while (--timeout && !(!is_on ^ !reg));
 
+	if (saved_config) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+		reg |= saved_config;
+		dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+	}
+
 	if (!timeout)
 		return -ETIMEDOUT;
 
@@ -4467,14 +4501,18 @@ static irqreturn_t dwc3_process_event_buf(struct dwc3_event_buffer *evt)
 	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
 		    DWC3_GEVNTSIZ_SIZE(evt->length));
 
+	evt->flags &= ~DWC3_EVENT_PENDING;
+	/*
+	 * Add an explicit write memory barrier to make sure that the update of
+	 * clearing DWC3_EVENT_PENDING is observed in dwc3_check_event_buf()
+	 */
+	wmb();
+
 	if (dwc->imod_interval) {
 		dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), DWC3_GEVNTCOUNT_EHB);
 		dwc3_writel(dwc->regs, DWC3_DEV_IMOD(0), dwc->imod_interval);
 	}
 
-	/* Keep the clearing of DWC3_EVENT_PENDING at the end */
-	evt->flags &= ~DWC3_EVENT_PENDING;
-
 	return ret;
 }