1 files changed, 42 insertions, 12 deletions

diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h
index 497f2b3a5a62..f9bd6e8ab138 100644
--- a/include/linux/iio/common/st_sensors.h
+++ b/include/linux/iio/common/st_sensors.h
@@ -105,6 +105,11 @@ struct st_sensor_fullscale {
 	struct st_sensor_fullscale_avl fs_avl[ST_SENSORS_FULLSCALE_AVL_MAX];
 };
 
+struct st_sensor_sim {
+	u8 addr;
+	u8 value;
+};
+
 /**
  * struct st_sensor_bdu - ST sensor device block data update
  * @addr: address of the register.
@@ -126,28 +131,39 @@ struct st_sensor_das {
 };
 
 /**
+ * struct st_sensor_int_drdy - ST sensor device drdy line parameters
+ * @addr: address of INT drdy register.
+ * @mask: mask to enable drdy line.
+ * @addr_od: address to enable/disable Open Drain on the INT line.
+ * @mask_od: mask to enable/disable Open Drain on the INT line.
+ */
+struct st_sensor_int_drdy {
+	u8 addr;
+	u8 mask;
+	u8 addr_od;
+	u8 mask_od;
+};
+
+/**
  * struct st_sensor_data_ready_irq - ST sensor device data-ready interrupt
- * @addr: address of the register.
- * @mask_int1: mask to enable/disable IRQ on INT1 pin.
- * @mask_int2: mask to enable/disable IRQ on INT2 pin.
+ * struct int1 - data-ready configuration register for INT1 pin.
+ * struct int2 - data-ready configuration register for INT2 pin.
  * @addr_ihl: address to enable/disable active low on the INT lines.
  * @mask_ihl: mask to enable/disable active low on the INT lines.
- * @addr_od: address to enable/disable Open Drain on the INT lines.
- * @mask_od: mask to enable/disable Open Drain on the INT lines.
- * @addr_stat_drdy: address to read status of DRDY (data ready) interrupt
+ * struct stat_drdy - status register of DRDY (data ready) interrupt.
  * struct ig1 - represents the Interrupt Generator 1 of sensors.
  * @en_addr: address of the enable ig1 register.
  * @en_mask: mask to write the on/off value for enable.
  */
 struct st_sensor_data_ready_irq {
-	u8 addr;
-	u8 mask_int1;
-	u8 mask_int2;
+	struct st_sensor_int_drdy int1;
+	struct st_sensor_int_drdy int2;
 	u8 addr_ihl;
 	u8 mask_ihl;
-	u8 addr_od;
-	u8 mask_od;
-	u8 addr_stat_drdy;
+	struct {
+		u8 addr;
+		u8 mask;
+	} stat_drdy;
 	struct {
 		u8 en_addr;
 		u8 en_mask;
@@ -197,6 +213,7 @@ struct st_sensor_transfer_function {
  * @bdu: Block data update register.
  * @das: Data Alignment Selection register.
  * @drdy_irq: Data ready register of the sensor.
+ * @sim: SPI serial interface mode register of the sensor.
  * @multi_read_bit: Use or not particular bit for [I2C/SPI] multi-read.
  * @bootime: samples to discard when sensor passing from power-down to power-up.
  */
@@ -213,6 +230,7 @@ struct st_sensor_settings {
 	struct st_sensor_bdu bdu;
 	struct st_sensor_das das;
 	struct st_sensor_data_ready_irq drdy_irq;
+	struct st_sensor_sim sim;
 	bool multi_read_bit;
 	unsigned int bootime;
 };
@@ -325,4 +343,16 @@ ssize_t st_sensors_sysfs_sampling_frequency_avail(struct device *dev,
 ssize_t st_sensors_sysfs_scale_avail(struct device *dev,
 				struct device_attribute *attr, char *buf);
 
+#ifdef CONFIG_OF
+void st_sensors_of_name_probe(struct device *dev,
+			      const struct of_device_id *match,
+			      char *name, int len);
+#else
+static inline void st_sensors_of_name_probe(struct device *dev,
+					    const struct of_device_id *match,
+					    char *name, int len)
+{
+}
+#endif
+
 #endif /* ST_SENSORS_H */