Age | Commit message (Collapse) | Author |
|
commit 3d56c25e3bb0726a5c5e16fc2d9e38f8ed763085 upstream.
Ascend-to-parent logics in d_walk() depends on all encountered child
dentries not getting freed without an RCU delay. Unfortunately, in
quite a few cases it is not true, with hard-to-hit oopsable race as
the result.
Fortunately, the fix is simiple; right now the rule is "if it ever
been hashed, freeing must be delayed" and changing it to "if it
ever had a parent, freeing must be delayed" closes that hole and
covers all cases the old rule used to cover. Moreover, pipes and
sockets remain _not_ covered, so we do not introduce RCU delay in
the cases which are the reason for having that delay conditional
in the first place.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2:
- Adjust context
- Also set the flag in __d_materialise_dentry())]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9c77679cadb118c0aa99e6f88533d91765a131ba upstream.
For newer versions of Syslinux, we need ldlinux.c32 in addition to
isolinux.bin to reside on the boot disk, so if the latter is found,
copy it, too, to the isoimage tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8b78f260887df532da529f225c49195d18fef36b upstream.
One of the debian buildd servers had this crash in the syslog without
any other information:
Unaligned handler failed, ret = -2
clock_adjtime (pid 22578): Unaligned data reference (code 28)
CPU: 1 PID: 22578 Comm: clock_adjtime Tainted: G E 4.5.0-2-parisc64-smp #1 Debian 4.5.4-1
task: 000000007d9960f8 ti: 00000001bde7c000 task.ti: 00000001bde7c000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111100000001111 Tainted: G E
r00-03 000000ff0804f80f 00000001bde7c2b0 00000000402d2be8 00000001bde7c2b0
r04-07 00000000409e1fd0 00000000fa6f7fff 00000001bde7c148 00000000fa6f7fff
r08-11 0000000000000000 00000000ffffffff 00000000fac9bb7b 000000000002b4d4
r12-15 000000000015241c 000000000015242c 000000000000002d 00000000fac9bb7b
r16-19 0000000000028800 0000000000000001 0000000000000070 00000001bde7c218
r20-23 0000000000000000 00000001bde7c210 0000000000000002 0000000000000000
r24-27 0000000000000000 0000000000000000 00000001bde7c148 00000000409e1fd0
r28-31 0000000000000001 00000001bde7c320 00000001bde7c350 00000001bde7c218
sr00-03 0000000001200000 0000000001200000 0000000000000000 0000000001200000
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000402d2e84 00000000402d2e88
IIR: 0ca0d089 ISR: 0000000001200000 IOR: 00000000fa6f7fff
CPU: 1 CR30: 00000001bde7c000 CR31: ffffffffffffffff
ORIG_R28: 00000002369fe628
IAOQ[0]: compat_get_timex+0x2dc/0x3c0
IAOQ[1]: compat_get_timex+0x2e0/0x3c0
RP(r2): compat_get_timex+0x40/0x3c0
Backtrace:
[<00000000402d4608>] compat_SyS_clock_adjtime+0x40/0xc0
[<0000000040205024>] syscall_exit+0x0/0x14
This means the userspace program clock_adjtime called the clock_adjtime()
syscall and then crashed inside the compat_get_timex() function.
Syscalls should never crash programs, but instead return EFAULT.
The IIR register contains the executed instruction, which disassebles
into "ldw 0(sr3,r5),r9".
This load-word instruction is part of __get_user() which tried to read the word
at %r5/IOR (0xfa6f7fff). This means the unaligned handler jumped in. The
unaligned handler is able to emulate all ldw instructions, but it fails if it
fails to read the source e.g. because of page fault.
The following program reproduces the problem:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/mman.h>
int main(void) {
/* allocate 8k */
char *ptr = mmap(NULL, 2*4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0);
/* free second half (upper 4k) and make it invalid. */
munmap(ptr+4096, 4096);
/* syscall where first int is unaligned and clobbers into invalid memory region */
/* syscall should return EFAULT */
return syscall(__NR_clock_adjtime, 0, ptr+4095);
}
To fix this issue we simply need to check if the faulting instruction address
is in the exception fixup table when the unaligned handler failed. If it
is, call the fixup routine instead of crashing.
While looking at the unaligned handler I found another issue as well: The
target register should not be modified if the handler was unsuccessful.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d14bdb553f9196169f003058ae1cdabe514470e6 upstream.
MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to
any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS
time, and the next KVM_RUN oopses:
general protection fault: 0000 [#1] SMP
CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
[...]
Call Trace:
[<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm]
[<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
[<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
[<ffffffff812418a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71
Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
RIP [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40
RSP <ffff88005836bd50>
Testcase (beautified/reduced from syzkaller output):
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[8];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
memcpy(&dr,
"\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72"
"\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8"
"\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9"
"\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb",
48);
r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr);
r[6] = ioctl(r[4], KVM_RUN, 0);
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e2dfb4b880146bfd4b6aa8e138c0205407cebbaf upstream.
PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Fixes: 8130b9d7b9d8 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers")
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Simon Marchi <simon.marchi@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 62397da50bb20a6b812c949ef465d7e69fe54bb6 upstream.
A wmediumd that does not send this attribute causes a NULL pointer
dereference, as the attribute is accessed even if it does not exist.
The attribute was required but never checked ever since userspace frame
forwarding has been introduced. The issue gets more problematic once we
allow wmediumd registration from user namespaces.
Fixes: 7882513bacb1 ("mac80211_hwsim driver support userspace frame tx/rx")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f49cf3b8b4c841457244c461c66186a719e13bcc upstream.
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d1b12075ffa808dce33dd46b7ad035bebf8da215 upstream.
Calling pwm_config() with a period equal to zero always results in
error (-EINVAL) and pwm chip config method is never called.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1ff5fa3c6732f08e01ae12f12286d4728c9e4d86 upstream.
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0de4cbb3dddca35ecd06b95918f38439c9c6401f upstream.
[ 598.852037] ------------[ cut here ]------------
[ 598.856698] WARNING: at lib/dma-debug.c:887 check_unmap+0xf8/0x920()
[ 598.863079] cxgb3 0000:01:00.0: DMA-API: device driver frees DMA memory with different size [device address=0x0000000003310000] [map size=17 bytes] [unmap size=16 bytes]
[ 598.878265] Modules linked in: xprtrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_sa ib_mad kvm_amd kvm ipmi_devintf ipmi_ssif dcdbas pcspkr ipmi_si sg ipmi_msghandler acpi_power_meter amd64_edac_mod shpchp edac_core sp5100_tco k10temp edac_mce_amd i2c_piix4 acpi_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_common ata_generic iw_cxgb3 pata_acpi ib_core ib_addr mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm pata_atiixp drm ahci libahci serio_raw i2c_core cxgb3 libata bnx2 mdio dm_mirror dm_region_hash dm_log dm_mod
[ 598.946822] CPU: 3 PID: 11820 Comm: cmtime Not tainted 3.10.0-327.el7.x86_64.debug #1
[ 598.954681] Hardware name: Dell Inc. PowerEdge R415/0GXH08, BIOS 2.0.2 10/22/2012
[ 598.962193] ffff8808077479a8 000000000381a432 ffff880807747960 ffffffff81700918
[ 598.969663] ffff880807747998 ffffffff8108b6c0 ffff880807747a80 ffff8808063f55c0
[ 598.977132] ffffffff833ca850 0000000000000282 ffff88080b1bb800 ffff880807747a00
[ 598.984602] Call Trace:
[ 598.987062] [<ffffffff81700918>] dump_stack+0x19/0x1b
[ 598.992224] [<ffffffff8108b6c0>] warn_slowpath_common+0x70/0xb0
[ 598.998254] [<ffffffff8108b75c>] warn_slowpath_fmt+0x5c/0x80
[ 599.004033] [<ffffffff813903b8>] check_unmap+0xf8/0x920
[ 599.009369] [<ffffffff81025959>] ? sched_clock+0x9/0x10
[ 599.014702] [<ffffffff81390cee>] debug_dma_free_coherent+0x7e/0xa0
[ 599.021008] [<ffffffffa01ece2c>] cxio_destroy_cq+0xcc/0x160 [iw_cxgb3]
[ 599.027654] [<ffffffffa01e8da0>] iwch_destroy_cq+0xf0/0x140 [iw_cxgb3]
[ 599.034307] [<ffffffffa01c4bfe>] ib_destroy_cq+0x1e/0x30 [ib_core]
[ 599.040601] [<ffffffffa04ff2d2>] ib_uverbs_close+0x302/0x4d0 [ib_uverbs]
[ 599.047417] [<ffffffff812335a2>] __fput+0x102/0x310
[ 599.052401] [<ffffffff8123388e>] ____fput+0xe/0x10
[ 599.057297] [<ffffffff810bbde4>] task_work_run+0xb4/0xe0
[ 599.062719] [<ffffffff81092a84>] do_exit+0x304/0xc60
[ 599.067789] [<ffffffff81025905>] ? native_sched_clock+0x35/0x80
[ 599.073820] [<ffffffff81025959>] ? sched_clock+0x9/0x10
[ 599.079153] [<ffffffff8170a49c>] ? _raw_spin_unlock_irq+0x2c/0x50
[ 599.085358] [<ffffffff8109346c>] do_group_exit+0x4c/0xc0
[ 599.090779] [<ffffffff810a8661>] get_signal_to_deliver+0x2e1/0x960
[ 599.097071] [<ffffffff8101c497>] do_signal+0x57/0x6e0
[ 599.102229] [<ffffffff81714bd1>] ? sysret_signal+0x5/0x4e
[ 599.107738] [<ffffffff8101cb7f>] do_notify_resume+0x5f/0xb0
[ 599.113418] [<ffffffff81714e7d>] int_signal+0x12/0x17
[ 599.118576] ---[ end trace 1e4653102e7e7019 ]---
[ 599.123211] Mapped at:
[ 599.125577] [<ffffffff8138ed8b>] debug_dma_alloc_coherent+0x2b/0x80
[ 599.131968] [<ffffffffa01ec862>] cxio_create_cq+0xf2/0x1f0 [iw_cxgb3]
[ 599.139920] [<ffffffffa01e9c05>] iwch_create_cq+0x105/0x4e0 [iw_cxgb3]
[ 599.147895] [<ffffffffa0500584>] create_cq.constprop.14+0x184/0x2e0 [ib_uverbs]
[ 599.156649] [<ffffffffa05027fb>] ib_uverbs_create_cq+0x10b/0x140 [ib_uverbs]
Fixes: b955150ea784 ('RDMA/cxgb3: When a user QP is marked in error, also mark the CQs in error')
Signed-off-by: Honggang Li <honli@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f0f393877c71ad227d36705d61d1e4062bc29cf5 upstream.
Commit ff1e22e7a638 ("xen/events: Mask a moving irq") open-coded
irq_move_irq() but left out checking if the IRQ is disabled. This broke
resuming from suspend since it tries to move a (disabled) irq without
holding the IRQ's desc->lock. Fix it by adding in a check for disabled
IRQs.
The resulting stacktrace was:
kernel BUG at /build/linux-UbQGH5/linux-4.4.0/kernel/irq/migration.c:31!
invalid opcode: 0000 [#1] SMP
Modules linked in: xenfs xen_privcmd ...
CPU: 0 PID: 9 Comm: migration/0 Not tainted 4.4.0-22-generic #39-Ubuntu
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125180 05/04/2016
task: ffff88003d75ee00 ti: ffff88003d7bc000 task.ti: ffff88003d7bc000
RIP: 0010:[<ffffffff810e26e2>] [<ffffffff810e26e2>] irq_move_masked_irq+0xd2/0xe0
RSP: 0018:ffff88003d7bfc50 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88003d40ba00 RCX: 0000000000000001
RDX: 0000000000000001 RSI: 0000000000000100 RDI: ffff88003d40bad8
RBP: ffff88003d7bfc68 R08: 0000000000000000 R09: ffff88003d000000
R10: 0000000000000000 R11: 000000000000023c R12: ffff88003d40bad0
R13: ffffffff81f3a4a0 R14: 0000000000000010 R15: 00000000ffffffff
FS: 0000000000000000(0000) GS:ffff88003da00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd4264de624 CR3: 0000000037922000 CR4: 00000000003406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff88003d40ba38 0000000000000024 0000000000000000 ffff88003d7bfca0
ffffffff814c8d92 00000010813ef89d 00000000805ea732 0000000000000009
0000000000000024 ffff88003cc39b80 ffff88003d7bfce0 ffffffff814c8f66
Call Trace:
[<ffffffff814c8d92>] eoi_pirq+0xb2/0xf0
[<ffffffff814c8f66>] __startup_pirq+0xe6/0x150
[<ffffffff814ca659>] xen_irq_resume+0x319/0x360
[<ffffffff814c7e75>] xen_suspend+0xb5/0x180
[<ffffffff81120155>] multi_cpu_stop+0xb5/0xe0
[<ffffffff811200a0>] ? cpu_stop_queue_work+0x80/0x80
[<ffffffff811203d0>] cpu_stopper_thread+0xb0/0x140
[<ffffffff810a94e6>] ? finish_task_switch+0x76/0x220
[<ffffffff810ca731>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20
[<ffffffff810a3935>] smpboot_thread_fn+0x105/0x160
[<ffffffff810a3830>] ? sort_range+0x30/0x30
[<ffffffff810a0588>] kthread+0xd8/0xf0
[<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0
[<ffffffff8182568f>] ret_from_fork+0x3f/0x70
[<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit bf959931ddb88c4e4366e96dd22e68fa0db9527c upstream.
The following program (simplified version of generated by syzkaller)
#include <pthread.h>
#include <unistd.h>
#include <sys/ptrace.h>
#include <stdio.h>
#include <signal.h>
void *thread_func(void *arg)
{
ptrace(PTRACE_TRACEME, 0,0,0);
return 0;
}
int main(void)
{
pthread_t thread;
if (fork())
return 0;
while (getppid() != 1)
;
pthread_create(&thread, NULL, thread_func, NULL);
pthread_join(thread, NULL);
return 0;
}
creates an unreapable zombie if /sbin/init doesn't use __WALL.
This is not a kernel bug, at least in a sense that everything works as
expected: debugger should reap a traced sub-thread before it can reap the
leader, but without __WALL/__WCLONE do_wait() ignores sub-threads.
Unfortunately, it seems that /sbin/init in most (all?) distributions
doesn't use it and we have to change the kernel to avoid the problem.
Note also that most init's use sys_waitid() which doesn't allow __WALL, so
the necessary user-space fix is not that trivial.
This patch just adds the "ptrace" check into eligible_child(). To some
degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is
mostly ignored when the tracee reports to debugger. Or WSTOPPED, the
tracer doesn't need to set this flag to wait for the stopped tracee.
This obviously means the user-visible change: __WCLONE and __WALL no
longer have any meaning for debugger. And I can only hope that this won't
break something, but at least strace/gdb won't suffer.
We could make a more conservative change. Say, we can take __WCLONE into
account, or !thread_group_leader(). But it would be nice to not
complicate these historical/confusing checks.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit affa80bd97f7ca282d1faa91667b3ee9e4c590e6 upstream.
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1740c29a46b30a2f157afc473156f157e599d4c2 upstream.
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a4128e ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4b9c7f9db9a003f5c342184dc4401c1b7f2efb39 upstream.
Commit 176e21ee2ec8 ("SUNRPC: Support for RPC over AF_LOCAL
transports") added a 5-character netid, but did not bump
RPCBIND_MAXNETIDLEN from 4 to 5.
Fixes: 176e21ee2ec8 ("SUNRPC: Support for RPC over AF_LOCAL ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1a967d6c9b39c226be1b45f13acd4d8a5ab3dc44 upstream.
Only server which map unknown users to guest will allow
access using a non-null NTLMv2_Response.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2:
- Adjust context, indentation
- Keep using cERROR()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 777f69b8d26bf35ade4a76b08f203c11e048365d upstream.
Only server which map unknown users to guest will allow
access using a non-null NTChallengeResponse.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2:
- Adjust context, indentation
- Keep using cERROR()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fa8f3a354bb775ec586e4475bcb07f7dece97e0c upstream.
Only server which map unknown users to guest will allow
access using a non-null LMChallengeResponse.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2:
- Adjust context, indentation
- Keep ses->flags assignment out of the new if-statement]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit cfda35d98298131bf38fbad3ce4cd5ecb3cf18db upstream.
See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client:
...
Set NullSession to FALSE
If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND
AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND
(AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1)
OR
AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0))
-- Special case: client requested anonymous authentication
Set NullSession to TRUE
...
Only server which map unknown users to guest will allow
access using a non-null NTChallengeResponse.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2: keep using cERROR()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ad67b437f187ea818b2860524d10f878fadfdd99 upstream.
b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
[bhelgaas: changelog]
Fixes: b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit da77b67195de1c65bef4908fa29967c4d0af2da2 upstream.
Commit b894157145e4 ("x86/PCI: Mark Broadwell-EP Home Agent & PCU as having
non-compliant BARs") marked Home Agent 0 & PCU has having non-compliant
BARs. Home Agent 1 also has non-compliant BARs.
Mark Home Agent 1 as having non-compliant BARs so the PCI core doesn't
touch them.
The problem with these devices is documented in the Xeon v4 specification
update:
BDF2 PCI BARs in the Home Agent Will Return Non-Zero Values
During Enumeration
Problem: During system initialization the Operating System may access
the standard PCI BARs (Base Address Registers). Due to
this erratum, accesses to the Home Agent BAR registers (Bus
1; Device 18; Function 0,4; Offsets (0x14-0x24) will return
non-zero values.
Implication: The operating system may issue a warning. Intel has not
observed any functional failures due to this erratum.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v4-spec-update.html
Fixes: b894157145e4 ("x86/PCI: Mark Broadwell-EP Home Agent & PCU as having non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2bb07e155bb3e0c722c806723f737cf8020961ef upstream.
Prevent using uninitialized or negative index when handling
steering entries.
Fixes: b12d93d63c32 ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1c447116d017a98c90f8f71c8c5a611e0aa42178 upstream.
Some eMMCs set the partition switch timeout too low.
Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable. Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.
Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.
The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 20878232c52329f92423d27a60e48b6a6389e0dd upstream.
Systems show a minimal load average of 0.00, 0.01, 0.05 even when they
have no load at all.
Uptime and /proc/loadavg on all systems with kernels released during the
last five years up until kernel version 4.6-rc5, show a 5- and 15-minute
minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on
idle systems, but the way the kernel calculates this value prevents it
from getting lower than the mentioned values.
Likewise but not as obviously noticeable, a fully loaded system with no
processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95
(multiplied by number of cores).
Once the (old) load becomes 93 or higher, it mathematically can never
get lower than 93, even when the active (load) remains 0 forever.
This results in the strange 0.00, 0.01, 0.05 uptime values on idle
systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05.
It is not correct to add a 0.5 rounding (=1024/2048) here, since the
result from this function is fed back into the next iteration again,
so the result of that +0.5 rounding value then gets multiplied by
(2048-2037), and then rounded again, so there is a virtual "ghost"
load created, next to the old and active load terms.
By changing the way the internally kept value is rounded, that internal
value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon
increasing load, the internally kept load value is rounded up, when the
load is decreasing, the load value is rounded down.
The modified code was tested on nohz=off and nohz kernels. It was tested
on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was
tested on single, dual, and octal cores system. It was tested on virtual
hosts and bare hardware. No unwanted effects have been observed, and the
problems that the patch intended to fix were indeed gone.
Tested-by: Damien Wyart <damien.wyart@free.fr>
Signed-off-by: Vik Heyndrickx <vik.heyndrickx@veribox.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Doug Smythies <dsmythies@telus.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0f004f5a696a ("sched: Cure more NO_HZ load average woes")
Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit aac55d7573c5d46ed9a62818d5d3e69dd2060105 upstream.
With Linux page size of 64K and hardware only supporting 4K HPTE, if we
use subpage protection, we always fail for the subpage 0 as shown
below (using the selftest subpage_prot test):
520175565: (4520111850): Failed at 0x3fffad4b0000 (p=13,sp=0,w=0), want=fault, got=pass !
4520890210: (4520826495): Failed at 0x3fffad5b0000 (p=29,sp=0,w=0), want=fault, got=pass !
4521574251: (4521510536): Failed at 0x3fffad6b0000 (p=45,sp=0,w=0), want=fault, got=pass !
4522258324: (4522194609): Failed at 0x3fffad7b0000 (p=61,sp=0,w=0), want=fault, got=pass !
This is because hash preload wrongly inserts the HPTE entry for subpage
0 without looking at the subpage protection information.
Fix it by teaching should_hash_preload() not to preload if we have
subpage protection configured for that range.
It appears this has been broken since it was introduced in 2008.
Fixes: fa28237cfcc5 ("[POWERPC] Provide a way to protect 4k subpages when using 64k pages")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rework into should_hash_preload() to avoid build fails w/SLICES=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8bbc9b7b001eaab8abf7e9e24edf1bb285c8d825 upstream.
Currently we have a check in hash_preload() against the psize, which is
only included when CONFIG_PPC_MM_SLICES is enabled. We want to expand
this check in a subsequent patch, so factor it out to allow that. As a
bonus it removes the #ifdef in the C code.
Unfortunately we can't put this in the existing CONFIG_PPC_MM_SLICES
block because it would require a forward declaration.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 55e610cdd28c0ad3dce0652030c0296d549673f3 upstream.
This lock is already taken in ata_scsi_queuecmd() a few levels up the
call stack so attempting to take it here is an error. Moreover, it is
pointless in the first place since it only protects a single, atomic
assignment.
Enabling lock debugging gives the following output:
=============================================
[ INFO: possible recursive locking detected ]
4.4.0-rc5+ #189 Not tainted
---------------------------------------------
kworker/u2:3/37 is trying to acquire lock:
(&(&host->lock)->rlock){-.-...}, at: [<90283294>] sata_dwc_exec_command_by_tag.constprop.14+0x44/0x8c
but task is already holding lock:
(&(&host->lock)->rlock){-.-...}, at: [<902761ac>] ata_scsi_queuecmd+0x2c/0x330
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&host->lock)->rlock);
lock(&(&host->lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u2:3/37:
#0: ("events_unbound"){.+.+.+}, at: [<9003a0a4>] process_one_work+0x12c/0x430
#1: ((&entry->work)){+.+.+.}, at: [<9003a0a4>] process_one_work+0x12c/0x430
#2: (&bdev->bd_mutex){+.+.+.}, at: [<9011fd54>] __blkdev_get+0x50/0x380
#3: (&(&host->lock)->rlock){-.-...}, at: [<902761ac>] ata_scsi_queuecmd+0x2c/0x330
stack backtrace:
CPU: 0 PID: 37 Comm: kworker/u2:3 Not tainted 4.4.0-rc5+ #189
Workqueue: events_unbound async_run_entry_fn
Stack : 90b38e30 00000021 00000003 9b2a6040 00000000 9005f3f0 904fc8dc 00000025
906b96e4 00000000 90528648 9b3336c4 904fc8dc 9009bf18 00000002 00000004
00000000 00000000 9b3336c4 9b3336e4 904fc8dc 9003d074 00000000 90500000
9005e738 00000000 00000000 00000000 00000000 00000000 00000000 00000000
6e657665 755f7374 756f626e 0000646e 00000000 00000000 9b00ca00 9b025000
...
Call Trace:
[<90009d6c>] show_stack+0x88/0xa4
[<90057744>] __lock_acquire+0x1ce8/0x2154
[<900583e4>] lock_acquire+0x64/0x8c
[<9045ff10>] _raw_spin_lock_irqsave+0x54/0x78
[<90283294>] sata_dwc_exec_command_by_tag.constprop.14+0x44/0x8c
[<90283484>] sata_dwc_qc_issue+0x1a8/0x24c
[<9026b39c>] ata_qc_issue+0x1f0/0x410
[<90273c6c>] ata_scsi_translate+0xb4/0x200
[<90276234>] ata_scsi_queuecmd+0xb4/0x330
[<9025800c>] scsi_dispatch_cmd+0xd0/0x128
[<90259934>] scsi_request_fn+0x58c/0x638
[<901a3e50>] __blk_run_queue+0x40/0x5c
[<901a83d4>] blk_queue_bio+0x27c/0x28c
[<901a5914>] generic_make_request+0xf0/0x188
[<901a5a54>] submit_bio+0xa8/0x194
[<9011adcc>] submit_bh_wbc.isra.23+0x15c/0x17c
[<9011c908>] block_read_full_page+0x3e4/0x428
[<9009e2e0>] do_read_cache_page+0xac/0x210
[<9009fd90>] read_cache_page+0x18/0x24
[<901bbd18>] read_dev_sector+0x38/0xb0
[<901bd174>] msdos_partition+0xb4/0x5c0
[<901bcb8c>] check_partition+0x140/0x274
[<901bba60>] rescan_partitions+0xa0/0x2b0
[<9011ff68>] __blkdev_get+0x264/0x380
[<901201ac>] blkdev_get+0x128/0x36c
[<901b9378>] add_disk+0x3c0/0x4bc
[<90268268>] sd_probe_async+0x100/0x224
[<90043a44>] async_run_entry_fn+0x50/0x124
[<9003a11c>] process_one_work+0x1a4/0x430
[<9003a4f4>] worker_thread+0x14c/0x4fc
[<900408f4>] kthread+0xd0/0xe8
[<90004338>] ret_from_kernel_thread+0x14/0x1c
Fixes: 62936009f35a ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex")
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c87bf431448b404a6ef5fbabd74c0e3e42157a7f upstream.
Enabling CONFIG_GCOV_PROFILE_ALL produces us a lot of warnings like
lib/lz4/lz4hc_compress.c: In function 'lz4_compresshcctx':
lib/lz4/lz4hc_compress.c:514:1: warning: the frame size of 1504 bytes is larger than 1024 bytes [-Wframe-larger-than=]
After some investigation, I found that this behavior started with gcc-4.9,
and opened https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69702.
A suggested workaround for it is to use the -fno-tree-loop-im
flag that turns off one of the optimization stages in gcc, so the
code runs a little slower but does not use excessive amounts
of stack.
We could make this conditional on the gcc version, but I could not
find an easy way to do this in Kbuild and the benefit would be
fairly small, given that most of the gcc version in production are
affected now.
I'm marking this for 'stable' backports because it addresses a bug
with code generation in gcc that exists in all kernel versions
with the affected gcc releases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 128639395b2ceacc6a56a0141d0261012bfe04d3 upstream.
Update the recent changes to set_pte() that were added in 46011e6ea392
to handle R10000_LLSC_WAR, and format the assembly to match other areas
of the MIPS tree using the same WAR.
This also incorporates a patch recently sent in my Markos Chandras,
"Remove local LL/SC preprocessor variants", so that patch doesn't need
to be applied if this one is accepted.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Fixes: 46011e6ea392 ("MIPS: Make set_pte() SMP safe.)
Cc: David Daney <david.daney@cavium.com>
Cc: Linux/MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/11103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[bwh: Backported to 3.2:
- Use {LL,SC}_INSN not __{LL,SC}
- Use literal arch=r4000 instead of MIPS_ISA_ARCH_LEVEL since R6 is not
supported]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f18ebc211e259d4f591e39e74b2aa2de226c9a1d upstream.
The problem with ornamental, do-nothing gotos is that they lead to
"forgot to set the error code" bugs. We should be returning -EINVAL
here but we don't. It leads to an uninitalized variable in
counter_show():
drivers/acpi/sysfs.c:603 counter_show()
error: uninitialized symbol 'status'.
Fixes: 1c8fce27e275 (ACPI: introduce drivers/acpi/sysfs.c)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 74d2a91aec97ab832790c9398d320413ad185321 upstream.
Add even more ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[johan: rebase and replace commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f0d09463c59c2d764a6c6d492cbe6d2c77f27153 upstream.
More ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[properly sort them - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6798df4c5fe0a7e6d2065cf79649a794e5ba7114 upstream.
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 309124e2648d668a0c23539c5078815660a4a850 upstream.
According to full-history-linux commit d3794f4fa7c3edc3 ("[PATCH] M68k
update (part 25)"), port operations are allowed on m68k if CONFIG_ISA is
defined.
However, commit 153dcc54df826d2f ("[PATCH] mem driver: fix conditional
on isa i/o support") accidentally changed an "||" into an "&&",
disabling it completely on m68k. This logic was retained when
introducing the DEVPORT symbol in commit 4f911d64e04a44c4 ("Make
/dev/port conditional on config symbol").
Drop the bogus dependency on !M68K to fix this.
Fixes: 153dcc54df826d2f ("[PATCH] mem driver: fix conditional on isa i/o support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c9eb13a9105e2e418f72e46a2b6da3f49e696902 upstream.
If the orphaned inode list contains inode #5, ext4_iget() returns a
bad inode (since the bootloader inode should never be referenced
directly). Because of the bad inode, we end up processing the inode
repeatedly and this hangs the machine.
This can be reproduced via:
mke2fs -t ext4 /tmp/foo.img 100
debugfs -w -R "ssv last_orphan 5" /tmp/foo.img
mount -o loop /tmp/foo.img /mnt
(But don't do this if you are using an unpatched kernel if you care
about the system staying functional. :-)
This bug was found by the port of American Fuzzy Lop into the kernel
to find file system problems[1]. (Since it *only* happens if inode #5
shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not
surprising that AFL needed two hours before it found it.)
[1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf
Reported by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fc4bf75ea300a5e62a2419f89dd0e22189dd7ab7 upstream.
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4c63c2454eff996c5e27991221106eb511f7db38 upstream.
32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can
be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr
fail.
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d1497977fecb9acce05988d6322ad415ef93bb39 upstream.
sg_dma_len() macro can be used only on scattelists which are mapped, so
all calls to it before dma_map_sg() are invalid. Replace them by proper
check for direct sg segment length read.
Fixes: a49e490c7a8a ("crypto: s5p-sss - add S5PV210 advanced crypto engine support")
Fixes: 9e4a1100a445 ("crypto: s5p-sss - Handle unaligned buffers")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.2: unaligned DMA is unsupported so there is a different
set of calls to replace]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c20e128030caf0537d5e906753eac1c28fefdb75 upstream.
The alpha pci_mmap_resource() is used for both IORESOURCE_MEM and
IORESOURCE_IO resources, but iomem_is_exclusive() is only applicable for
IORESOURCE_MEM.
Call iomem_is_exclusive() only for IORESOURCE_MEM resources, and do it
earlier to match the generic version of pci_mmap_resource().
Fixes: 10a0ef39fbd1 ("PCI/alpha: pci sysfs resources")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ca620723d4ff9ea7ed484eab46264c3af871b9ae upstream.
iomem_is_exclusive() requires a CPU physical address, but on some arches we
supplied a PCI bus address instead.
On most arches, pci_resource_to_user(res) returns "res->start", which is a
CPU physical address. But on microblaze, mips, powerpc, and sparc, it
returns the PCI bus address corresponding to "res->start".
The result is that pci_mmap_resource() may fail when it shouldn't (if the
bus address happens to match an existing resource), or it may succeed when
it should fail (if the resource is exclusive but the bus address doesn't
match it).
Call iomem_is_exclusive() with "res->start", which is always a CPU physical
address, not the result of pci_resource_to_user().
Fixes: e8de1481fd71 ("resource: allow MMIO exclusivity for device drivers")
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 79152e8d085fd64484afd473ef6830b45518acba upstream.
The tcrypt testing module on Exynos5422-based Odroid XU3/4 board failed on
testing 8 kB size blocks:
$ sudo modprobe tcrypt sec=1 mode=500
testing speed of async ecb(aes) (ecb-aes-s5p) encryption
test 0 (128 bit key, 16 byte blocks): 21971 operations in 1 seconds (351536 bytes)
test 1 (128 bit key, 64 byte blocks): 21731 operations in 1 seconds (1390784 bytes)
test 2 (128 bit key, 256 byte blocks): 21932 operations in 1 seconds (5614592 bytes)
test 3 (128 bit key, 1024 byte blocks): 21685 operations in 1 seconds (22205440 bytes)
test 4 (128 bit key, 8192 byte blocks):
This was caused by a race issue of missed BRDMA_DONE ("Block cipher
Receiving DMA") interrupt. Device starts processing the data in DMA mode
immediately after setting length of DMA block: receiving (FCBRDMAL) or
transmitting (FCBTDMAL). The driver sets these lengths from interrupt
handler through s5p_set_dma_indata() function (or xxx_setdata()).
However the interrupt handler was first dealing with receive buffer
(dma-unmap old, dma-map new, set receive block length which starts the
operation), then with transmit buffer and finally was clearing pending
interrupts (FCINTPEND). Because of the time window between setting
receive buffer length and clearing pending interrupts, the operation on
receive buffer could end already and driver would miss new interrupt.
User manual for Exynos5422 confirms in example code that setting DMA
block lengths should be the last operation.
The tcrypt hang could be also observed in following blocked-task dmesg:
INFO: task modprobe:258 blocked for more than 120 seconds.
Not tainted 4.6.0-rc4-next-20160419-00005-g9eac8b7b7753-dirty #42
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c06b09d8 0 258 256 0x00000000
[<c06b09d8>] (__schedule) from [<c06b0f24>] (schedule+0x40/0xac)
[<c06b0f24>] (schedule) from [<c06b49f8>] (schedule_timeout+0x124/0x178)
[<c06b49f8>] (schedule_timeout) from [<c06b17fc>] (wait_for_common+0xb8/0x144)
[<c06b17fc>] (wait_for_common) from [<bf0013b8>] (test_acipher_speed+0x49c/0x740 [tcrypt])
[<bf0013b8>] (test_acipher_speed [tcrypt]) from [<bf003e8c>] (do_test+0x2240/0x30ec [tcrypt])
[<bf003e8c>] (do_test [tcrypt]) from [<bf008048>] (tcrypt_mod_init+0x48/0xa4 [tcrypt])
[<bf008048>] (tcrypt_mod_init [tcrypt]) from [<c010177c>] (do_one_initcall+0x3c/0x16c)
[<c010177c>] (do_one_initcall) from [<c0191ff0>] (do_init_module+0x5c/0x1ac)
[<c0191ff0>] (do_init_module) from [<c0185610>] (load_module+0x1a30/0x1d08)
[<c0185610>] (load_module) from [<c0185ab0>] (SyS_finit_module+0x8c/0x98)
[<c0185ab0>] (SyS_finit_module) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Fixes: a49e490c7a8a ("crypto: s5p-sss - add S5PV210 advanced crypto engine support")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7b9bc799a445aea95f64f15e0083cb19b5789abe upstream.
BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop. However, the polarity of the led pin is reversed. It should be
red for wifi off and blue for wifi on, but it is the opposite. This bug was
reported in the following bug report:
http://pad.lv/972604
Fixes: 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin configuration for compaq c700 laptop")
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 267c85860308d36bc163c5573308cd024f659d7c upstream.
Setting the flag 'cache_bypass' will bypass the cache not the hardware.
Fix this comment here.
Fixes: 0eef6b0415f5 ("regmap: Fix doc comment")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
|
|
commit 79e48650320e6fba48369fccf13fd045315b19b8 upstream.
Stack object "dte_facilities" is allocated in x25_rx_call_request(),
which is supposed to be initialized in x25_negotiate_facilities.
However, 5 fields (8 bytes in total) are not initialized. This
object is then copied to userland via copy_to_user, thus infoleak
occurs.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5f8e44741f9f216e33736ea4ec65ca9ac03036e6 upstream.
The stack object “map” has a total size of 32 bytes. Its last 4
bytes are padding generated by compiler. These padding bytes are
not initialized and sent out via “nla_put”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b8670c09f37bdf2847cc44f36511a53afc6161fd upstream.
The stack object “info” has a total size of 12 bytes. Its last byte
is padding which is not initialized and leaked via “put_cmsg”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 31b0b385f69d8d5491a4bca288e25e63f1d945d0 upstream.
The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.
Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.
This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.
Fixes: 5b3501faa874 ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 99d825822eade8d827a1817357cbf3f889a552d6 upstream.
Payloads of NM entries are not supposed to contain NUL. When we run
into such, only the part prior to the first NUL goes into the
concatenation (i.e. the directory entry name being encoded by a bunch
of NM entries). We do stop when the amount collected so far + the
claimed amount in the current NM entry exceed 254. So far, so good,
but what we return as the total length is the sum of *claimed*
sizes, not the actual amount collected. And that can grow pretty
large - not unlimited, since you'd need to put CE entries in
between to be able to get more than the maximum that could be
contained in one isofs directory entry / continuation chunk and
we are stop once we'd encountered 32 CEs, but you can get about 8Kb
easily. And that's what will be passed to readdir callback as the
name length. 8Kb __copy_to_user() from a buffer allocated by
__get_free_page()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f0b22d1bb2a37a665a969e95785c75a4f49d1499 upstream.
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit 3bb457af4fa8
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
This bug was found by strace test suite.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|