| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 9c284c41c0886f09e75c323a16278b6d353b0b4a upstream.
The existing code gives an incorrect pointer value.
The buffer pointer 'buf' was of type unsigned short *, and 'count' was a
number in bytes. A cast of buf should have been used.
However, instead of casting, just change the code to use u32 pointers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8185e51f358a: ("mmc: tmio-mmc: add support for 32bit data port")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49d31c2f389acfe83417083e1208422b4091cd9e upstream.
take_dentry_name_snapshot() takes a safe snapshot of dentry name;
if the name is a short one, it gets copied into caller-supplied
structure, otherwise an extra reference to external name is grabbed
(those are never modified). In either case the pointer to stable
string is stored into the same structure.
dentry must be held by the caller of take_dentry_name_snapshot(),
but may be freely dropped afterwards - the snapshot will stay
until destroyed by release_dentry_name_snapshot().
Intended use:
struct name_snapshot s;
take_dentry_name_snapshot(&s, dentry);
...
access s.name
...
release_dentry_name_snapshot(&s);
Replaces fsnotify_oldname_...(), gets used in fsnotify to obtain the name
to pass down with event.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 860f01e96981a68553f3ca49f574ff14fe955e72 upstream.
systemd by default starts watchdog on reboot and sets the timer to
ShutdownWatchdogSec=10min. Reboot handler in ipmi_watchdog than reduces
the timer to 120s which is not enough time to boot a Xen machine with
a lot of RAM. As a result the machine is rebooted the second time
during the long run of (XEN) Scrubbing Free RAM.....
Fix this by setting the timer to 120s only if it was previously
set to a low value.
Signed-off-by: Valentin Vidic <Valentin.Vidic@CARNet.hr>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f5af546e6acc30f075828cb58c7f09665033967 upstream.
This fixes a potential buffer overflow in isdn_net.c caused by an
unbounded strcpy.
[ ISDN seems to be effectively unmaintained, and the I4L driver in
particular is long deprecated, but in case somebody uses this..
- Linus ]
Signed-off-by: Jiten Thakkar <jitenmt@gmail.com>
Signed-off-by: Annie Cherkaev <annie.cherk@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 283d6860d64f5091565bf729b0a6d6af14ae6c27 upstream.
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
v2:
- In the stable tag also include versions which need backporting (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: a1b2278e4dfc ("drm/i915: skylake panel fitting using shared scalers")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 5fb9dadf336f3590c799e8cbde348215dccc2aa2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38bcb208f60924a031b9f809f7cd252ea4a94e5f upstream.
Bit 30 being set causes the upper half of BAR2 to stay in physical mode,
mapped over the end of VRAM, even when the rest of the BAR has been set
to virtual mode.
We inherited our initial value from RM, but I'm not aware of any reason
we need to keep it that way.
This fixes severe GPU hang/lockup issues revealed by Wayland on F26.
Shout-out to NVIDIA for the quick response with the potential cause!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a90e049cacd965dade4dae7263b4d3fd550e78b6 upstream.
GP102's cursors go from chan 17..20. Increase the array size to hold
their data properly.
Fixes: e50fcff15f ("drm/nouveau/disp/gp102: fix cursor/overlay immediate channel indices")
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b009e76797c82178d7a03ae0eaad5951d975277 upstream.
This was originally chosen to be an arbitrarily large number. However,
some user mode may actually try to set a 16Kx16K mode and run into other
issues.
Since 8Kx8K is the current texture limit for Mesa LLVM driver, we will
just use this limit for now.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcfffdd8f98ac305285dca568b5065ef86be6458 upstream.
The current code does not look correct, and the reason for it is
probably lost. Since this now generates a compiler warning,
fix it to what makes sense.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e96d559634b73a8158ee99a7abece2eacec2668 upstream.
Since thread_group worker and raid5d kthread are not in sync, if
worker writes stripe before raid5d then requests will be waiting
for issue_pendig.
Issue observed when building raid5 with ext4, in some build runs
jbd2 would get hung and requests were waiting in the HW engine
waiting to be issued.
Fix this by adding a call to async_tx_issue_pending_all in the
raid5_do_work.
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16d56e2fcc1fc15b981369653c3b41d7ff0b443d upstream.
After bio is submitted, we should not clone it as its bi_iter might be
invalid by driver. This is the case of behind_master_bio. In certain
situration, we could dispatch behind_master_bio immediately for the
first disk and then clone it for other disks.
https://bugzilla.kernel.org/show_bug.cgi?id=196383
Reported-and-tested-by: Markus <m4rkusxxl@web.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Fix: 841c1316c7da(md: raid1: improve write behind)
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 022e510fcbda79183fd2cdc01abb01b4be80d03f upstream.
bio_add_page() won't fail for resync bio, and the page index for each
bio is same, so remove it.
More importantly the 'idx' of 'struct resync_pages' is initialized in
mempool allocator function, the current way is wrong since mempool is
only responsible for allocation, we can't use that for initialization.
Suggested-by: NeilBrown <neilb@suse.com>
Reported-by: NeilBrown <neilb@suse.com>
Reported-and-tested-by: Patrick <dto@gmx.net>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc86a41e96c5b6f07453c405e036d95acc673389 upstream.
If the dm-integrity superblock was corrupted in such a way that the
journal_sections field was zero, the integrity target would deadlock
because it would wait forever for free space in the journal.
Detect this situation and refuse to activate the device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 7eada909bfd7 ("dm: add integrity target")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9dd59727dbc21d33a9add4c5b308a5775cd5a6ef upstream.
When using a block size greater than 512 bytes, the dm-integrity target
allocates journal space inefficiently. It allocates one journal entry
for each 512-byte chunk of data, fills an entry for each block of data
and leaves the remaining entries unused.
This issue doesn't cause data corruption, but all the unused journal
entries degrade performance severely.
For example, with 4k blocks and an 8k bio, it would allocate 16 journal
entries but only use 2 entries. The remaining 14 entries were left
unused.
Fix this by adding the missing 'log2_sectors_per_block' shifts that are
required to have each journal entry map to a full block.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 7eada909bfd7 ("dm: add integrity target")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef42719814db06fdfa26cd7566de0b64de173320 upstream.
Commit f98a8bf9ee20 ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB
ioctl() to change HPT size", 2016-12-20) changed the behaviour of
the KVM_PPC_ALLOCATE_HTAB ioctl so that it now allocates a new HPT
and new revmap array if there was a previously-allocated HPT of a
different size from the size being requested. In this case, we need
to reset the rmap arrays of the memslots, because the rmap arrays
will contain references to HPTEs which are no longer valid. Worse,
these references are also references to slots in the new revmap
array (which parallels the HPT), and the new revmap array contains
random contents, since it doesn't get zeroed on allocation.
The effect of having these stale references to slots in the revmap
array that contain random contents is that subsequent calls to
functions such as kvmppc_add_revmap_chain will crash because they
will interpret the non-zero contents of the revmap array as HPTE
indexes and thus index outside of the revmap array. This leads to
host crashes such as the following.
[ 7072.862122] Unable to handle kernel paging request for data at address 0xd000000c250c00f8
[ 7072.862218] Faulting instruction address: 0xc0000000000e1c78
[ 7072.862233] Oops: Kernel access of bad area, sig: 11 [#1]
[ 7072.862286] SMP NR_CPUS=1024
[ 7072.862286] NUMA
[ 7072.862325] PowerNV
[ 7072.862378] Modules linked in: kvm_hv vhost_net vhost tap xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables rpcrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm iw_cxgb3 mlx5_ib ib_core ses enclosure scsi_transport_sas ipmi_powernv ipmi_devintf ipmi_msghandler powernv_op_panel i2c_opal nfsd auth_rpcgss oid_registry
[ 7072.863085] nfs_acl lockd grace sunrpc kvm_pr kvm xfs libcrc32c scsi_dh_alua dm_service_time radeon lpfc nvme_fc nvme_fabrics nvme_core scsi_transport_fc i2c_algo_bit tg3 drm_kms_helper ptp pps_core syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm dm_multipath i2c_core cxgb3 mlx5_core mdio [last unloaded: kvm_hv]
[ 7072.863381] CPU: 72 PID: 56929 Comm: qemu-system-ppc Not tainted 4.12.0-kvm+ #59
[ 7072.863457] task: c000000fe29e7600 task.stack: c000001e3ffec000
[ 7072.863520] NIP: c0000000000e1c78 LR: c0000000000e2e3c CTR: c0000000000e25f0
[ 7072.863596] REGS: c000001e3ffef560 TRAP: 0300 Not tainted (4.12.0-kvm+)
[ 7072.863658] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE,TM[E]>
[ 7072.863667] CR: 44082882 XER: 20000000
[ 7072.863767] CFAR: c0000000000e2e38 DAR: d000000c250c00f8 DSISR: 42000000 SOFTE: 1
GPR00: c0000000000e2e3c c000001e3ffef7e0 c000000001407d00 d000000c250c00f0
GPR04: d00000006509fb70 d00000000b3d2048 0000000003ffdfb7 0000000000000000
GPR08: 00000001007fdfb7 00000000c000000f d0000000250c0000 000000000070f7bf
GPR12: 0000000000000008 c00000000fdad000 0000000010879478 00000000105a0d78
GPR16: 00007ffaf4080000 0000000000001190 0000000000000000 0000000000010000
GPR20: 4001ffffff000415 d00000006509fb70 0000000004091190 0000000ee1881190
GPR24: 0000000003ffdfb7 0000000003ffdfb7 00000000007fdfb7 c000000f5c958000
GPR28: d00000002d09fb70 0000000003ffdfb7 d00000006509fb70 d00000000b3d2048
[ 7072.864439] NIP [c0000000000e1c78] kvmppc_add_revmap_chain+0x88/0x130
[ 7072.864503] LR [c0000000000e2e3c] kvmppc_do_h_enter+0x84c/0x9e0
[ 7072.864566] Call Trace:
[ 7072.864594] [c000001e3ffef7e0] [c000001e3ffef830] 0xc000001e3ffef830 (unreliable)
[ 7072.864671] [c000001e3ffef830] [c0000000000e2e3c] kvmppc_do_h_enter+0x84c/0x9e0
[ 7072.864751] [c000001e3ffef920] [d00000000b38d878] kvmppc_map_vrma+0x168/0x200 [kvm_hv]
[ 7072.864831] [c000001e3ffef9e0] [d00000000b38a684] kvmppc_vcpu_run_hv+0x1284/0x1300 [kvm_hv]
[ 7072.864914] [c000001e3ffefb30] [d00000000f465664] kvmppc_vcpu_run+0x44/0x60 [kvm]
[ 7072.865008] [c000001e3ffefb60] [d00000000f461864] kvm_arch_vcpu_ioctl_run+0x114/0x290 [kvm]
[ 7072.865152] [c000001e3ffefbe0] [d00000000f453c98] kvm_vcpu_ioctl+0x598/0x7a0 [kvm]
[ 7072.865292] [c000001e3ffefd40] [c000000000389328] do_vfs_ioctl+0xd8/0x8c0
[ 7072.865410] [c000001e3ffefde0] [c000000000389be4] SyS_ioctl+0xd4/0x130
[ 7072.865526] [c000001e3ffefe30] [c00000000000b760] system_call+0x58/0x6c
[ 7072.865644] Instruction dump:
[ 7072.865715] e95b2110 793a0020 7b4926e4 7f8a4a14 409e0098 807c000c 786326e4 7c6a1a14
[ 7072.865857] 935e0008 7bbd0020 813c000c 913e000c <93a30008> 93bc000c 48000038 60000000
[ 7072.866001] ---[ end trace 627b6e4bf8080edc ]---
Note that to trigger this, it is necessary to use a recent upstream
QEMU (or other userspace that resizes the HPT at CAS time), specify
a maximum memory size substantially larger than the current memory
size, and boot a guest kernel that does not support HPT resizing.
This fixes the problem by resetting the rmap arrays when the old HPT
is freed.
Fixes: f98a8bf9ee20 ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB ioctl() to change HPT size")
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e47057151422a67ce08747176fa21cb3b526a2c9 upstream.
Commit 46a704f8409f ("KVM: PPC: Book3S HV: Preserve userspace HTM state
properly", 2017-06-15) added code to read transactional memory (TM)
registers but forgot to enable TM before doing so. The result is
that if userspace does have live values in the TM registers, a KVM_RUN
ioctl will cause a host kernel crash like this:
[ 181.328511] Unrecoverable TM Unavailable Exception f60 at d00000001e7d9980
[ 181.328605] Oops: Unrecoverable TM Unavailable Exception, sig: 6 [#1]
[ 181.328613] SMP NR_CPUS=2048
[ 181.328613] NUMA
[ 181.328618] PowerNV
[ 181.328646] Modules linked in: vhost_net vhost tap nfs_layout_nfsv41_files rpcsec_gss_krb5 nfsv4 dns_resolver nfs
+fscache xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat
+nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun ebtable_filter ebtables
+ip6table_filter ip6_tables iptable_filter bridge stp llc kvm_hv kvm nfsd ses enclosure scsi_transport_sas ghash_generic
+auth_rpcgss gf128mul xts sg ctr nfs_acl lockd vmx_crypto shpchp ipmi_powernv i2c_opal grace ipmi_devintf i2c_core
+powernv_rng sunrpc ipmi_msghandler ibmpowernv uio_pdrv_genirq uio leds_powernv powernv_op_panel ip_tables xfs sd_mod
+lpfc ipr bnx2x libata mdio ptp pps_core scsi_transport_fc libcrc32c dm_mirror dm_region_hash dm_log dm_mod
[ 181.329278] CPU: 40 PID: 9926 Comm: CPU 0/KVM Not tainted 4.12.0+ #1
[ 181.329337] task: c000003fc6980000 task.stack: c000003fe4d80000
[ 181.329396] NIP: d00000001e7d9980 LR: d00000001e77381c CTR: d00000001e7d98f0
[ 181.329465] REGS: c000003fe4d837e0 TRAP: 0f60 Not tainted (4.12.0+)
[ 181.329523] MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE>
[ 181.329527] CR: 24022448 XER: 00000000
[ 181.329608] CFAR: d00000001e773818 SOFTE: 1
[ 181.329608] GPR00: d00000001e77381c c000003fe4d83a60 d00000001e7ef410 c000003fdcfe0000
[ 181.329608] GPR04: c000003fe4f00000 0000000000000000 0000000000000000 c000003fd7954800
[ 181.329608] GPR08: 0000000000000001 c000003fc6980000 0000000000000000 d00000001e7e2880
[ 181.329608] GPR12: d00000001e7d98f0 c000000007b19000 00000001295220e0 00007fffc0ce2090
[ 181.329608] GPR16: 0000010011886608 00007fff8c89f260 0000000000000001 00007fff8c080028
[ 181.329608] GPR20: 0000000000000000 00000100118500a6 0000010011850000 0000010011850000
[ 181.329608] GPR24: 00007fffc0ce1b48 0000010011850000 00000000d673b901 0000000000000000
[ 181.329608] GPR28: 0000000000000000 c000003fdcfe0000 c000003fdcfe0000 c000003fe4f00000
[ 181.330199] NIP [d00000001e7d9980] kvmppc_vcpu_run_hv+0x90/0x6b0 [kvm_hv]
[ 181.330264] LR [d00000001e77381c] kvmppc_vcpu_run+0x2c/0x40 [kvm]
[ 181.330322] Call Trace:
[ 181.330351] [c000003fe4d83a60] [d00000001e773478] kvmppc_set_one_reg+0x48/0x340 [kvm] (unreliable)
[ 181.330437] [c000003fe4d83b30] [d00000001e77381c] kvmppc_vcpu_run+0x2c/0x40 [kvm]
[ 181.330513] [c000003fe4d83b50] [d00000001e7700b4] kvm_arch_vcpu_ioctl_run+0x114/0x2a0 [kvm]
[ 181.330586] [c000003fe4d83bd0] [d00000001e7642f8] kvm_vcpu_ioctl+0x598/0x7a0 [kvm]
[ 181.330658] [c000003fe4d83d40] [c0000000003451b8] do_vfs_ioctl+0xc8/0x8b0
[ 181.330717] [c000003fe4d83de0] [c000000000345a64] SyS_ioctl+0xc4/0x120
[ 181.330776] [c000003fe4d83e30] [c00000000000b004] system_call+0x58/0x6c
[ 181.330833] Instruction dump:
[ 181.330869] e92d0260 e9290b50 e9290108 792807e3 41820058 e92d0260 e9290b50 e9290108
[ 181.330941] 792ae8a4 794a1f87 408204f4 e92d0260 <7d4022a6> f9490ff0 e92d0260 7d4122a6
[ 181.331013] ---[ end trace 6f6ddeb4bfe92a92 ]---
The fix is just to turn on the TM bit in the MSR before accessing the
registers.
Fixes: 46a704f8409f ("KVM: PPC: Book3S HV: Preserve userspace HTM state properly")
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41cdf7a45389e01991ee31e3301ed83cb3e3f7dc upstream.
When authencesn is used together with digest_null a crash will
occur on the decrypt path. This is because normally we perform
a special setup to preserve the ESN, but this is skipped if there
is no authentication. However, on the post-authentication path
it always expects the preservation to be in place, thus causing
a crash when digest_null is used.
This patch fixes this by also skipping the post-processing when
there is no authentication.
Fixes: 104880a6b470 ("crypto: authencesn - Convert to new AEAD...")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efc856edfd66acc5da34fec92d7feca6fd0f9add upstream.
SPU driver is dependent on generic MAILBOX API's to
communicate with underlying DMA engine driver.
So this patch removes BCM_PDC_MBOX "depends on" for SPU driver
in Kconfig and adds MAILBOX as dependent module.
Fixes: 9d12ba86f818 ("crypto: brcm - Add Broadcom SPU driver")
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7e6e5d8b221e57fed9fda6ec81153fda773c073 upstream.
In Broadcom SPU driver, due to missing break statement
in spu2_hash_xlate() while mapping SPU2 equivalent
SHA3-512 value, -EINVAL is chosen and hence leading to
failure of SHA3-512 algorithm. This patch fixes the same.
Fixes: 9d12ba86f818 ("crypto: brcm - Add Broadcom SPU driver")
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4b201d88b7c9b3c6acdd03f9adec0c9857548ce upstream.
Update the cpp include flags for compiling device tree dts files
to match the changes made to the kernel build process in
commit d5d332d3f7e8 ("devicetree: Move include prefixes from arch
to separate directory").
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7dbcc0e433f0f61acb89ed9861ec996be4f2b38 upstream.
nfs4_retry_setlk() sets the task's state to TASK_INTERRUPTIBLE within the
same region protected by the wait_queue's lock after checking for a
notification from CB_NOTIFY_LOCK callback. However, after releasing that
lock, a wakeup for that task may race in before the call to
freezable_schedule_timeout_interruptible() and set TASK_WAKING, then
freezable_schedule_timeout_interruptible() will set the state back to
TASK_INTERRUPTIBLE before the task will sleep. The result is that the task
will sleep for the entire duration of the timeout.
Since we've already set TASK_INTERRUPTIBLE in the locked section, just use
freezable_schedule_timout() instead.
Fixes: a1d617d8f134 ("nfs: allow blocking locks to be awoken by lock callbacks")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 442ce0499c0535f8972b68fa1fda357357a5c953 upstream.
Prior to commit ca0daa277aca ("NFS: Cache aggressively when file is open
for writing"), NFS would revalidate, or invalidate, the file size when
taking a lock. Since that commit it only invalidates the file content.
If the file size is changed on the server while wait for the lock, the
client will have an incorrect understanding of the file size and could
corrupt data. This particularly happens when writing beyond the
(supposed) end of file and can be easily be demonstrated with
posix_fallocate().
If an application opens an empty file, waits for a write lock, and then
calls posix_fallocate(), glibc will determine that the underlying
filesystem doesn't support fallocate (assuming version 4.1 or earlier)
and will write out a '0' byte at the end of each 4K page in the region
being fallocated that is after the end of the file.
NFS will (usually) detect that these writes are beyond EOF and will
expand them to cover the whole page, and then will merge the pages.
Consequently, NFS will write out large blocks of zeroes beyond where it
thought EOF was. If EOF had moved, the pre-existing part of the file
will be over-written. Locking should have protected against this,
but it doesn't.
This patch restores the use of nfs_zap_caches() which invalidated the
cached attributes. When posix_fallocate() asks for the file size, the
request will go to the server and get a correct answer.
Fixes: ca0daa277aca ("NFS: Cache aggressively when file is open for writing")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26cb2be4c7c42644ccd147c786edb9006300ee56 upstream.
The register for the "new timing mode" also has bit fields for setting
output and sample timing phases. According to comments in Allwinner's
BSP kernel, the default values are good enough.
Keep the default values already in the hardware when setting new timing
mode, instead of overwriting the whole register.
Fixes: 9a37e53e451e ("mmc: sunxi: Enable the new timings for the A64 MMC
controllers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fd1bd443e80b12f0a01a45fb9a793206b41cb72 upstream.
As for commit 68baf692c435 ("powerpc/pseries: Fix of_node_put()
underflow during DLPAR remove"), the call to of_node_put() must be
removed from pSeries_reconfig_remove_node().
dlpar_detach_node() and pSeries_reconfig_remove_node() both call
of_detach_node(), and thus the node should not be released in both
cases.
Fixes: 0829f6d1f69e ("of: device_node kobject lifecycle fixes")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56188832a50f09998cb570ba3771a1d25c193c0e upstream.
Some machines can't power off the machine, so disable the lockup detectors to
avoid this watchdog BUG to show up every few seconds:
watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [systemd-shutdow:1]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56008c04ebc099940021b714da2d7779117cf6a7 upstream.
It's always bothered me that we only disable preemption in
copy_user_page around the call to flush_dcache_page_asm.
This patch extends this to after the copy.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
equivalent aliases
commit ae7a609c34b6fb12328c553b5f9aab26ae74a28e upstream.
Helge noticed that we flush the TLB page in flush_cache_page but not in
flush_cache_range or flush_cache_mm.
For a long time, we have had random segmentation faults building
packages on machines with PA8800/8900 processors. These machines only
support equivalent aliases. We don't see these faults on machines that
don't require strict coherency. So, it appears TLB speculation
sometimes leads to cache corruption on machines that require coherency.
This patch adds TLB flushes to flush_cache_range and flush_cache_mm when
coherency is required. We only flush the TLB in flush_cache_page when
coherency is required.
The patch also optimizes flush_cache_range. It turns out we always have
the right context to use flush_user_dcache_range_asm and
flush_user_icache_range_asm.
The patch has been tested for some time on rp3440, rp3410 and A500-44.
It's been boot tested on c8000. No random segmentation faults were
observed during testing.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba92b1142879731f80377770f4710e5f0a953aad upstream.
Mic mute led does not work on HP ProBook 440 G4.
We can use CXT_FIXUP_MUTE_LED_GPIO fixup to support it.
BugLink: https://bugs.launchpad.net/bugs/1705586
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74ec118152ea494a25ebb677cbc83a75c982ac5f upstream.
Add codec IDs for several recently released, pending, and historical
NVIDIA GPU audio controllers to the patch table, to allow the correct
patch functions to be selected for them.
Signed-off-by: Daniel Dadap <ddadap@nvidia.com>
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 610e1ae9b533be82b3aa118b907e0a703256913d upstream.
The commit b56fa687e02b ("ALSA: fm801: detect FM-only card earlier")
rearranged initialization calls, i.e. it makes snd_fm801_chip_init() to
be called before we register interrupt handler and set PCI bus
mastering.
Somehow it prevents FM801-AU to work properly. Thus, partially revert
initialization order changed by commit mentioned above.
Fixes: b56fa687e02b ("ALSA: fm801: detect FM-only card earlier")
Reported-by: Émeric MASCHINO <emeric.maschino@gmail.com>
Tested-by: Émeric MASCHINO <emeric.maschino@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9bcf66c72d726322441ec82962994e69157613e4 upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__jfs_set_acl() into jfs_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b49d9458aa351605b43a7e34598caef
CC: jfs-discussion@lists.sourceforge.net
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 0e4097c3354e2f5a5ad8affd9dc7f7f7d00bb6b9 upstream.
Recent kernels trigger this warning:
BUG: using smp_processor_id() in preemptible [00000000] code: 99-trinity/181
caller is debug_smp_processor_id+0x17/0x19
CPU: 0 PID: 181 Comm: 99-trinity Not tainted 4.12.0-01059-g2a42eb9 #1
Call Trace:
dump_stack+0x82/0xb8
check_preemption_disabled()
debug_smp_processor_id()
vtime_delta()
task_cputime()
thread_group_cputime()
thread_group_cputime_adjusted()
wait_consider_task()
do_wait()
SYSC_wait4()
do_syscall_64()
entry_SYSCALL64_slow_path()
As Frederic pointed out:
| Although those sched_clock_cpu() things seem to only matter when the
| sched_clock() is unstable. And that stability is a condition for nohz_full
| to work anyway. So probably sched_clock() alone would be enough.
This patch fixes it by replacing sched_clock_cpu() with sched_clock() to
avoid calling smp_processor_id() in a preemptible context.
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1499586028-7402-1-git-send-email-wanpeng.li@hotmail.com
[ Prettified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ff86bf0c65f1 ("alarmtimer: Rate limit periodic intervals") sets a
minimum bound on the alarm timer interval. This minimum bound shouldn't
be applied if the interval is 0. Otherwise, one-shot timers will be
converted into periodic ones.
This patch is specific to 4.11.y and 4.12.y. Older -stable trees have a
slightly different patch, and 4.13-rc2 isn't impacted due to a later
refactoring.
Fixes: ff86bf0c65f1 ("alarmtimer: Rate limit periodic intervals")
Reported-by: Ben Fennema <fennema@google.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dea1d0f5f1284e3defee4b8484d9fc230686cd42 upstream.
The move of the unpark functions to the control thread moved the BUG_ON()
there as well. While it made some sense in the idle thread of the upcoming
CPU, it's bogus to crash the control thread on the already online CPU,
especially as the function has a return value and the callsite is prepared
to handle an error return.
Replace it with a WARN_ON_ONCE() and return a proper error code.
Fixes: 9cd4f1a4e7a8 ("smp/hotplug: Move unparking of percpu threads to the control CPU")
Rightfully-ranted-at-by: Linux Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cd4f1a4e7a858849e889a081a99adff83e08e4c upstream.
Vikram reported the following backtrace:
BUG: scheduling while atomic: swapper/7/0/0x00000002
CPU: 7 PID: 0 Comm: swapper/7 Not tainted 4.9.32-perf+ #680
schedule
schedule_hrtimeout_range_clock
schedule_hrtimeout
wait_task_inactive
__kthread_bind_mask
__kthread_bind
__kthread_unpark
kthread_unpark
cpuhp_online_idle
cpu_startup_entry
secondary_start_kernel
He analyzed correctly that a parked cpu hotplug thread of an offlined CPU
was still on the runqueue when the CPU came back online and tried to unpark
it. This causes the thread which invoked kthread_unpark() to call
wait_task_inactive() and subsequently schedule() with preemption disabled.
His proposed workaround was to "make sure" that a parked thread has
scheduled out when the CPU goes offline, so the situation cannot happen.
But that's still wrong because the root cause is not the fact that the
percpu thread is still on the runqueue and neither that preemption is
disabled, which could be simply solved by enabling preemption before
calling kthread_unpark().
The real issue is that the calling thread is the idle task of the upcoming
CPU, which is not supposed to call anything which might sleep. The moron,
who wrote that code, missed completely that kthread_unpark() might end up
in schedule().
The solution is simpler than expected. The thread which controls the
hotplug operation is waiting for the CPU to call complete() on the hotplug
state completion. So the idle task of the upcoming CPU can set its state to
CPUHP_AP_ONLINE_IDLE and invoke complete(). This in turn wakes the control
task on a different CPU, which then can safely do the unpark and kick the
now unparked hotplug thread of the upcoming CPU to complete the bringup to
the final target state.
Control CPU AP
bringup_cpu();
__cpu_up() ------------>
bringup_ap();
bringup_wait_for_ap()
wait_for_completion();
cpuhp_online_idle();
<------------ complete();
unpark(AP->stopper);
unpark(AP->hotplugthread);
while(1)
do_idle();
kick(AP->hotplugthread);
wait_for_completion(); hotplug_thread()
run_online_callbacks();
complete();
Fixes: 8df3e07e7f21 ("cpu/hotplug: Let upcoming cpu bring itself fully up")
Reported-by: Vikram Mulukutla <markivx@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707042218020.2131@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c75b185274b7766fe69c2e73607c1ed780b284b upstream.
There are still cases on these platforms where an attempt is made to
configure the CDCLK while the power domain is off, like when coming back
from a suspend. So the workaround below is still needed.
This effectively reverts commit 63ff30442519 ("drm/i915: Nuke the
VLV/CHV PFI programming power domain workaround").
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101517
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170628210605.4994-1-krisman@collabora.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 886015a0ad43c7fc034b23ea4614ba39162f9ddd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04941829b0049d2446c7042ab9686dd057d809a6 upstream.
OA buffer initialization involves access to HW registers to set
the OA base, head and tail. Ensure device is awake while setting
these. With this, all oa.ops are covered under RPM and forcewake
wakelock.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498585181-23048-1-git-send-email-sagar.a.kamble@intel.com
Fixes: d79651522e89c ("drm/i915: Enable i915 perf stream for Haswell OA unit")
(cherry picked from commit 987f8c444aa2c33d98e7030d0c5f0a5325cc84ea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7581d5ca2bb269cfc2ce2d0cb489aac513167f6b upstream.
Commit fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer
flushes") adds a dependency to ifbdev->vma when flushing the framebufer,
but the checks are only against the existence of the ifbdev->fb and not
against ifbdev->vma. This leaves a window of opportunity where we may
try to operate on the fbdev prior to it being probed (thanks to
asynchronous booting).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101534
Fixes: fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer flushes")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622160211.783-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit 15727ed0d944ce1dec8b9e1082dd3df29a0fdf44)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db9108e054700c96322b0f0028546aa4e643cf0b upstream.
Hit the kmemleak when executing instance_rmdir, it forgot releasing
mem of tracing_cpumask. With this fix, the warn does not appear any
more.
unreferenced object 0xffff93a8dfaa7c18 (size 8):
comm "mkdir", pid 1436, jiffies 4294763622 (age 9134.308s)
hex dump (first 8 bytes):
ff ff ff ff ff ff ff ff ........
backtrace:
[<ffffffff88b6567a>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8861ea41>] __kmalloc_node+0xf1/0x280
[<ffffffff88b505d3>] alloc_cpumask_var_node+0x23/0x30
[<ffffffff88b5060e>] alloc_cpumask_var+0xe/0x10
[<ffffffff88571ab0>] instance_mkdir+0x90/0x240
[<ffffffff886e5100>] tracefs_syscall_mkdir+0x40/0x70
[<ffffffff886565c9>] vfs_mkdir+0x109/0x1b0
[<ffffffff8865b1d0>] SyS_mkdir+0xd0/0x100
[<ffffffff88403857>] do_syscall_64+0x67/0x150
[<ffffffff88b710e7>] return_from_SYSCALL_64+0x0/0x6a
[<ffffffffffffffff>] 0xffffffffffffffff
Link: http://lkml.kernel.org/r/1500546969-12594-1-git-send-email-chuhu@redhat.com
Fixes: ccfe9e42e451 ("tracing: Make tracing_cpumask available for all instances")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
present
commit 975e83cfb8dc16e7a2fdc58188c77c0c605876c2 upstream.
If the genpd->attach_dev or genpd->power_on fails, genpd_dev_pm_attach
may return -EPROBE_DEFER initially. However genpd_alloc_dev_data sets
the PM domain for the device unconditionally.
When subsequent attempts are made to call genpd_dev_pm_attach, it may
return -EEXISTS checking dev->pm_domain without re-attempting to call
attach_dev or power_on.
platform_drv_probe then attempts to call drv->probe as the return value
-EEXIST != -EPROBE_DEFER, which may end up in a situation where the
device is accessed without it's power domain switched on.
Fixes: f104e1e5ef57 (PM / Domains: Re-order initialization of generic_pm_domain_data)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 799ee2970485dc206c3bf347d6e6827c04d5e4f9 upstream.
The parallel panel driver should continue to work without having an
endpoint linking to an panel in DT for backwards compatibility.
With the recent switch to drm_of_find_panel_or_bridge, an absent
panel results in a failure with -ENODEV error return code. To restore
the old behaviour, ignore the -ENODEV return code.
Reported-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Fixes: ebc944613567 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbb3be170ac2891526ad07b18af7db226879a8e7 upstream.
Fix warnings of the form...
WARNING: CPU: 10 PID: 4983 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/class/dax/dax12.0'
Call Trace:
dump_stack+0x63/0x86
__warn+0xcb/0xf0
warn_slowpath_fmt+0x5a/0x80
? kernfs_path_from_node+0x4f/0x60
sysfs_warn_dup+0x62/0x80
sysfs_do_create_link_sd.isra.2+0x97/0xb0
sysfs_create_link+0x25/0x40
device_add+0x266/0x630
devm_create_dax_dev+0x2cf/0x340 [dax]
dax_pmem_probe+0x1f5/0x26e [dax_pmem]
nvdimm_bus_probe+0x71/0x120
...by reusing the namespace id for the device-dax instance name.
Now that we have decided that there will never by more than one
device-dax instance per libnvdimm-namespace parent device [1], we can
directly reuse the namepace ids. There are some possible follow-on
cleanups, but those are saved for a later patch to simplify the -stable
backport.
[1]: https://lists.01.org/pipermail/linux-nvdimm/2016-December/008266.html
Fixes: 98a29c39dc68 ("libnvdimm, namespace: allow creation of multiple pmem...")
Cc: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6883cd7f68245e43e91e5ee583b7550abf14523f upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__reiserfs_set_acl() into reiserfs_set_acl(). That way the function will
not be called when inheriting ACLs which is what we want as it prevents
SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes: 073931017b49d9458aa351605b43a7e34598caef
CC: reiserfs-devel@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d50daa2af2618dab6d21634e65a5fbcf4ae437d6 upstream.
Include the OF-based modalias in the uevent sent when registering SPMI
devices, so that user space has a chance to autoload the kernel module
for the device.
Tested-by: Rob Clark <robdclark@gmail.com>
Reported-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e34e1f23d780978da65968327cbba6d7013a73f upstream.
The busy percent calculated for the Knights Landing (KNL) platform
is 1024 times smaller than the correct busy value. This causes
performance to get stuck at the lowest ratio.
The scaling algorithm used for KNL is performance-based, but it still
looks at the CPU load to set the scaled busy factor to 0 when the
load is less than 1 percent. In this case, since the computed load
is 1024x smaller than it should be, the scaled busy factor will
always be 0, irrespective of CPU business.
This needs a fix similar to the turbostat one in commit b2b34dfe4d9a
(tools/power turbostat: KNL workaround for %Busy and Avg_MHz).
For this reason, add one more callback to processor-specific
callbacks to specify an MPERF multiplier represented by a number of
bit positions to shift the value of that register to the left to
copmensate for its rate difference with respect to the TSC. This
shift value is used during CPU busy calculations.
Fixes: ffb810563c (intel_pstate: Avoid getting stuck in high P-states when idle)
Reported-and-tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6463a4571ceefc43908df4b016d8d5d8b8e85357 upstream.
This problem shows up in 4.11 when netvsc driver is removed and reloaded.
The problem is that the channel is closed during module removal and the
tasklet for processing responses is disabled. When module is reloaded
the channel is reopened but the tasklet is marked as disabled.
The fix is to re-enable tasklet at the end of close which gets it back
to the initial state.
The issue is less urgent in 4.12 since network driver now uses NAPI
and not the tasklet; and other VMBUS devices are rarely unloaded/reloaded.
Fixes: dad72a1d2844 ("vmbus: remove hv_event_tasklet_disable/enable")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e700d2c59e5853c9126642976b4f5768f64c9b3 upstream.
nfit_init() calls nfit_mce_register() on module load. When the module
load fails the nfit mce decoder is not unregistered. The module's
memory is freed leaving the decoder chain referencing junk. This will
cause panics as future registrations will reference the free'd memory.
Unregister the nfit mce decoder on module init failure.
[v2]: register and then unregister mce handler to avoid losing mce events
[v3]: also cleanup nfit workqueue
Fixes: 6839a6d96f4e ("nfit: do an ARS scrub on hitting a latent media error")
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: "Lee, Chun-Yi" <joeyli.kernel@gmail.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: lszubowi@redhat.com
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 112166f88cf83dd11486cf1818672d42b540865b upstream.
The reason to disable interrupts seems to be to avoid switching to a
different processor while handling per cpu data using individual loads and
stores. If we use per cpu RMV primitives we will not have to disable
interrupts.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705171055130.5898@east.gentwo.org
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
