| Age | Commit message (Collapse) | Author |
|---|
|
commit 87ab9f6b7417349aa197a6c7098d4fdd4beebb74 upstream.
This reverts commit 39aead8373b3c20bb5965c024dfb51a94e526151.
Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev. It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-3-deller@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a06247c6804f1a7c86a2e5398a4c1f1db1471848 upstream.
With write operation on psi files replacing old trigger with a new one,
the lifetime of its waitqueue is totally arbitrary. Overwriting an
existing trigger causes its waitqueue to be freed and pending poll()
will stumble on trigger->event_wait which was destroyed.
Fix this by disallowing to redefine an existing psi trigger. If a write
operation is used on a file descriptor with an already existing psi
trigger, the operation will fail with EBUSY error.
Also bypass a check for psi_disabled in the psi_trigger_destroy as the
flag can be flipped after the trigger is created, leading to a memory
leak.
Fixes: 0e94682b73bf ("psi: introduce psi monitor")
Reported-by: syzbot+cdb5dd11c97cc532efad@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Analyzed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220111232309.1786347-1-surenb@google.com
[surenb: backported to 5.10 kernel]
CC: stable@vger.kernel.org # 5.10
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17a30422621c0e04cb6060d20d7edcefd7463347 upstream.
This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.
Fixes: 4edd396a1911 ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33950f9a36aca55c2b1e6062d9b29f3e97f91c40 upstream.
Exynos7 watchdog driver is clearly indicating that its dts node must
define syscon phandle property. That was probably forgotten, so add it.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 2b9366b66967 ("watchdog: s3c2410_wdt: Add support for Watchdog device on Exynos7")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-2-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 640f35b871d29cd685ce0ea0762636381beeb98a upstream.
This property was already mentioned in the old textual bindings
amlogic,meson-vpu.txt, but got dropped during conversion.
Adding it back similar to amlogic,gx-vdec.yaml.
Fixes: 6b9ebf1e0e67 ("dt-bindings: display: amlogic, meson-vpu: convert to yaml")
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219094155.177206-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22bf4047d26980807611b7e2030803db375afd87 upstream.
This is used in meson-gx and meson-g12. Add the property to the binding.
This fixes the dtschema warning:
hdmi-tx@c883a000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Fixes: 376bf52deef5 ("dt-bindings: display: amlogic, meson-dw-hdmi: convert to yaml")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211223122434.39378-2-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0ac702f3329cdc8a06dcaac73183d4b5a2b942d upstream.
Adjust the path of the ABI files for firewire.rst to prevent a
documentation build error. Prevents this problem:
Sphinx parallel build error:
docutils.utils.SystemMessage: Documentation/driver-api/firewire.rst:22: (SEVERE/4) Problems with "include" directive path:
InputError: [Errno 2] No such file or directory: '../Documentation/driver-api/ABI/stable/firewire-cdev'.
Fixes: 2f4830ef96d2 ("FireWire: add driver-api Introduction section")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/r/20220119033905.4779-1-rdunlap@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
randomization
commit 82ca67321f55a8d1da6ac3ed611da3c32818bb37 upstream.
The config RANDOMIZE_SLAB does not exist, the authors probably intended to
refer to the config RANDOMIZE_BASE, which provides kernel address-space
randomization. They probably just confused SLAB with BASE (these two
four-letter words coincidentally share three common letters), as they also
point out the config SLAB_FREELIST_RANDOM as further randomization within
the same sentence.
Fix the reference of the config for kernel address-space randomization to
the config that provides that.
Fixes: 6e88559470f5 ("Documentation: Add section about CPU vulnerabilities for Spectre")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211230171940.27558-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a11174952205d082f1658fab4314f0caf706e0a8 upstream.
The data node reference documentation was missing a package that must
contain the property values, instead property name and multiple values
being present in a single package. This is not aligned with the _DSD
spec.
Fix it by adding the package for the values.
Also add the missing "reg" properties to two numbered nodes.
Fixes: b10134a3643d ("ACPI: property: Document hierarchical data extension references")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c61d7b2ef141abf81140756b45860a2306f395a2 upstream.
Currently the documentation states that channels must be configured before
running the dmatest. This has not been true since commit 6b41030fdc79
("dmaengine: dmatest: Restore default for channel"). Fix accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20211118100952.27268-3-daniel.thompson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01f68f067dc39df9c9d95d759ee61517eb4b0fcf ]
Currently, the STM32 LP Timer counter driver registers into both IIO and
counter subsystems, which is redundant.
Remove the IIO counter ABI and IIO registration from the STM32 LP Timer
counter driver since it's been superseded by the Counter subsystem
as discussed in [1].
Keep only the counter subsystem related part.
Move a part of the ABI documentation into a driver comment.
This also removes a duplicate ABI warning
$ scripts/get_abi.pl validate
...
/sys/bus/iio/devices/iio:deviceX/in_count0_preset is defined 2 times:
./Documentation/ABI/testing/sysfs-bus-iio-timer-stm32:100
./Documentation/ABI/testing/sysfs-bus-iio-lptimer-stm32:0
[1] https://lkml.org/lkml/2021/1/19/347
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1611926542-2490-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49bcb1506f2e095262c01bda7fd1c0db524c91e2 ]
When converting the thermal-zones bindings to yaml the definition of the
contribution property changed. The intention is the same, an integer
value expressing a ratio of a sum on how much cooling is provided by the
device to the zone. But after the conversion the integer value is
limited to the range 0 to 100 and expressed as a percentage.
This is problematic for two reasons.
- This do not match how the binding is used. Out of the 18 files that
make use of the property only two (ste-dbx5x0.dtsi and
ste-hrefv60plus.dtsi) sets it at a value that satisfy the binding,
100. The remaining 16 files set the value higher and fail to validate.
- Expressing the value as a percentage instead of a ratio of the sum is
confusing as there is nothing to enforce the sum in the zone is not
greater then 100.
This patch restore the pre yaml conversion description and removes the
value limitation allowing the usage of the bindings to validate.
Fixes: 1202a442a31fd2e5 ("dt-bindings: thermal: Add yaml bindings for thermal zones")
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211109103045.1403686-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 08389d888287c3823f80b0216766b71e17f0aba5 upstream.
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9222ba68c3f4065f6364b99cc641b6b019ef2d42 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0ff29701ffad9a5d5a24344d8b09f3af7b96ffda upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33acc ("KVM: VMX: Emulate invalid guest state by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa72394667e5cea3547e4c41ddff7ca8c632d764 upstream.
Adds a new "alc285-hp-amp-init" model that can be used to apply the ALC285
HP speaker amplifier initialization fixup to devices that are not already
known by passing "hda_model=alc285-hp-amp-init" to the
snd-sof-intel-hda-common module or "model=alc285-hp-amp-init" to the
snd-hda-intel module, depending on which is being used.
Signed-off-by: Bradley Scott <bscott@teksavvy.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211213162246.506838-1-bscott@teksavvy.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c15b05baea71a5ff98235783e3e4ad227760876 ]
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 271225fd57c2f1e0b3f8826df51be6c634affefe ]
Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1cabe74f148f7b99d9f08274a62467f96c870f07 upstream.
gcc-plugin.sh has been removed in commit
1e860048c53e ("gcc-plugins: simplify GCC plugin-dev capability test").
Signed-off-by: Robert Karszniewicz <r.karszniewicz@phytec.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b6164342e981d751e69f5a165dd596ffcdfd6fe upstream.
This document was written a long time ago. Update it.
[1] Drop the version information
The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c53e
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.
We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.
[2] Drop the C compiler statements
Since commit 77342a02ff6e ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.
[3] Drop supported architectures
As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".
[4] Update the apt-get example
We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.
[5] Update the build target
Since commit ce2fd53a10c7 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.
[6] Update the steps for adding a new plugin
At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdfdc ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e58159a ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.
The sub-directory support was never used by anyone, and removed by
commit c17d6179ad5a ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").
Remove the useless $(src)/ prefix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96db48c9d777a73a33b1d516c5cfed7a417a5f40 upstream.
This binding was already documented in phy.txt, commit 252ae5330daa
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c109
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c109 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a631c0432dcccbcf45839016a07c015e335e9ae upstream.
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682f51 ("sched: Make migrate_disable/enable() independent of RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c95c07836fa4c1767ed11d8eca0769c652760e32 ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900aa ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c3645717 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f595d6a6cdc336834552069a2e0a4f6d4756ddf ]
fscrypt currently requires a 512-bit master key when AES-256-XTS is
used, since AES-256-XTS keys are 512-bit and fscrypt requires that the
master key be at least as long any key that will be derived from it.
However, this is overly strict because AES-256-XTS doesn't actually have
a 512-bit security strength, but rather 256-bit. The fact that XTS
takes twice the expected key size is a quirk of the XTS mode. It is
sufficient to use 256 bits of entropy for AES-256-XTS, provided that it
is first properly expanded into a 512-bit key, which HKDF-SHA512 does.
Therefore, relax the check of the master key size to use the security
strength of the derived key rather than the size of the derived key
(except for v1 encryption policies, which don't use HKDF).
Besides making things more flexible for userspace, this is needed in
order for the use of a KDF which only takes a 256-bit key to be
introduced into the fscrypt key hierarchy. This will happen with
hardware-wrapped keys support, as all known hardware which supports that
feature uses an SP800-108 KDF using AES-256-CMAC, so the wrapped keys
are wrapped 256-bit AES keys. Moreover, there is interest in fscrypt
supporting the same type of AES-256-CMAC based KDF in software as an
alternative to HKDF-SHA512. There is no security problem with such
features, so fix the key length check to work properly with them.
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Link: https://lore.kernel.org/r/20210921030303.5598-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 40fdea0284bb20814399da0484a658a96c735d90 upstream.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
s5m8767,pmic-buck-default-dvs-idx property
commit a7fda04bc9b6ad9da8e19c9e6e3b1dab773d068a upstream.
The driver was always parsing "s5m8767,pmic-buck-default-dvs-idx", not
"s5m8767,pmic-buck234-default-dvs-idx".
Cc: <stable@vger.kernel.org>
Fixes: 26aec009f6b6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-3-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
disabled
commit b16bef60a9112b1e6daf3afd16484eb06e7ce792 upstream.
The driver and its bindings, before commit 04f9f068a619 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a619 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b2d70c0dbf2731a37d1c7bcc86ab2387954d5f56 ]
make dtbs_check:
arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dt.yaml: bridge@2c: reg:0:0: 45 was expected
According to the datasheet, the I2C address can be either 0x2c or 0x2d,
depending on the ADDR control input.
Fixes: e3896e6dddf0b821 ("dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/08f73c2aa0d4e580303357dfae107d084d962835.1632486753.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 778cb8e39f6ec252be50fc3850d66f3dcbd5dd5a ]
"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.
"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.
Fix the equation by substituting s/>=/<=/.
Suggested-by: Ryan J. Barnett <ryan.barnett@collins.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210610143945.3504781-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 55c21d57eafb7b379bb7b3e93baf9ca2695895b0 upstream.
Fix board compatible typo reported by dtbs_check.
Fixes: f4d1577e9bc6 ("dt-bindings: arm: Convert Tegra board/soc bindings to json-schema")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210912165120.188490-1-david@ixit.cz
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8d7e415d55610d503fdb8815344846b72d194a40 ]
Starting from the beginning of infiniband subsystem, the uverbs char
devices start from 192 as a minor number, see
commit bc38a6abdd5a ("[PATCH] IB uverbs: core implementation").
This patch updates the admin guide documentation to reflect it.
Fixes: 9d85025b0418 ("docs-rst: create an user's manual book")
Link: https://lore.kernel.org/r/bad03e6bcde45550c01e12908a6fe7dfa4770703.1627477347.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit baf8d6899b1e8906dc076ef26cc633e96a8bb0c3 ]
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d6953009 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d1f278da6b11585f05b2755adfc8851cbf14a1ec ]
When scsi_dispatch_cmd was moved to scsi_lib.c and made static, some
compilers (i.e., at least gcc 8.4.0) decided to compile this
inline. This is a problem for lkdtm.ko, which inserted a kprobe
on this function for the SCSI_DISPATCH_CMD crashpoint.
Move this crashpoint one function up the call chain to
scsi_queue_rq. Though this is also a static function, it should never be
inlined because it is assigned as a structure entry. Therefore,
kprobe_register should always be able to find it.
Fixes: 82042a2cdb55 ("scsi: move scsi_dispatch_cmd to scsi_lib.c")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Link: https://lore.kernel.org/r/20210819022940.561875-2-kevmitch@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c8094e394bceb4f1880f9d539bdd255c130826e ]
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
Fixes: 993dcfac64eb ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema")
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5e60f363b38fd40e4d8838b5d6f4d4ecee92c777 upstream.
Documentation was not changed when renaming the script in commit
80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to
gen_initramfs.sh"). Fixing this.
Basically does:
$ sed -i -e s/gen_initramfs_list.sh/gen_initramfs.sh/g $(git grep -l gen_initramfs_list.sh)
Fixes: 80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to gen_initramfs.sh")
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e71e2ace5721a8b921dca18b045069e7bb411277 upstream.
Patch series "userfaultfd: do not untag user pointers", v5.
If a user program uses userfaultfd on ranges of heap memory, it may end
up passing a tagged pointer to the kernel in the range.start field of
the UFFDIO_REGISTER ioctl. This can happen when using an MTE-capable
allocator, or on Android if using the Tagged Pointers feature for MTE
readiness [1].
When a fault subsequently occurs, the tag is stripped from the fault
address returned to the application in the fault.address field of struct
uffd_msg. However, from the application's perspective, the tagged
address *is* the memory address, so if the application is unaware of
memory tags, it may get confused by receiving an address that is, from
its point of view, outside of the bounds of the allocation. We observed
this behavior in the kselftest for userfaultfd [2] but other
applications could have the same problem.
Address this by not untagging pointers passed to the userfaultfd ioctls.
Instead, let the system call fail. Also change the kselftest to use
mmap so that it doesn't encounter this problem.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
This patch (of 2):
Do not untag pointers passed to the userfaultfd ioctls. Instead, let
the system call fail. This will provide an early indication of problems
with tag-unaware userspace code instead of letting the code get confused
later, and is consistent with how we decided to handle brk/mmap/mremap
in commit dcde237319e6 ("mm: Avoid creating virtual address aliases in
brk()/mmap()/mremap()"), as well as being consistent with the existing
tagged address ABI documentation relating to how ioctl arguments are
handled.
The code change is a revert of commit 7d0325749a6c ("userfaultfd: untag
user pointers") plus some fixups to some additional calls to
validate_range that have appeared since then.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
Link: https://lkml.kernel.org/r/20210714195437.118982-1-pcc@google.com
Link: https://lkml.kernel.org/r/20210714195437.118982-2-pcc@google.com
Link: https://linux-review.googlesource.com/id/I761aa9f0344454c482b83fcfcce547db0a25501b
Fixes: 63f0c6037965 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mitch Phillips <mitchp@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William McVicker <willmcvicker@google.com>
Cc: <stable@vger.kernel.org> [5.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e3bac71c5053c99d438771fc9fa5082ae5d90aa upstream.
Currently the histogram logic allows the user to write "cpu" in as an
event field, and it will record the CPU that the event happened on.
The problem with this is that there's a lot of events that have "cpu"
as a real field, and using "cpu" as the CPU it ran on, makes it
impossible to run histograms on the "cpu" field of events.
For example, if I want to have a histogram on the count of the
workqueue_queue_work event on its cpu field, running:
># echo 'hist:keys=cpu' > events/workqueue/workqueue_queue_work/trigger
Gives a misleading and wrong result.
Change the command to "common_cpu" as no event should have "common_*"
fields as that's a reserved name for fields used by all events. And
this makes sense here as common_cpu would be a field used by all events.
Now we can even do:
># echo 'hist:keys=common_cpu,cpu if cpu < 100' > events/workqueue/workqueue_queue_work/trigger
># cat events/workqueue/workqueue_queue_work/hist
# event histogram
#
# trigger info: hist:keys=common_cpu,cpu:vals=hitcount:sort=hitcount:size=2048 if cpu < 100 [active]
#
{ common_cpu: 0, cpu: 2 } hitcount: 1
{ common_cpu: 0, cpu: 4 } hitcount: 1
{ common_cpu: 7, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 1 } hitcount: 1
{ common_cpu: 0, cpu: 6 } hitcount: 2
{ common_cpu: 0, cpu: 5 } hitcount: 2
{ common_cpu: 1, cpu: 1 } hitcount: 4
{ common_cpu: 6, cpu: 6 } hitcount: 4
{ common_cpu: 5, cpu: 5 } hitcount: 14
{ common_cpu: 4, cpu: 4 } hitcount: 26
{ common_cpu: 0, cpu: 0 } hitcount: 39
{ common_cpu: 2, cpu: 2 } hitcount: 184
Now for backward compatibility, I added a trick. If "cpu" is used, and
the field is not found, it will fall back to "common_cpu" and work as
it did before. This way, it will still work for old programs that use
"cpu" to get the actual CPU, but if the event has a "cpu" as a field, it
will get that event's "cpu" field, which is probably what it wants
anyway.
I updated the tracefs/README to include documentation about both the
common_timestamp and the common_cpu. This way, if that text is present in
the README, then an application can know that common_cpu is supported over
just plain "cpu".
Link: https://lkml.kernel.org/r/20210721110053.26b4f641@oasis.local.home
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 8b7622bf94a44 ("tracing: Add cpu field for hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 213ad73d06073b197a02476db3a4998e219ddb06 ]
Multiple complaints have been raised from the TFO users on the internet
stating that the TFO blackhole logic is too aggressive and gets falsely
triggered too often.
(e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/)
Considering that most middleboxes no longer drop TFO packets, we decide
to disable the blackhole logic by setting
/proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default.
Fixes: cf1ef3f0719b4 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92e669017ff1616ba7d8ba3c65f5193bc2a7acbe ]
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain, so fix the binding example accordingly.
In relation with fix c5a283802573 ("ARM: dts: at91: Configure I2C SCL
gpio as open drain").
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 19e5cef058a0 ("dt-bindings: i2c: at91: document optional bus recovery properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c16dc40aab84bab9cf54c2b61a458bb86b180c3 ]
Otherwise whole section after tab will be invisible in compiled
html format document.
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes: 89272ca1102e ("docs: filesystems: convert f2fs.txt to ReST")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed78f56e1271f108e8af61baeba383dcd77adbec ]
In case performance stats for an nvdimm are not available, reading the
'perf_stats' sysfs file returns an -ENOENT error. A better approach is
to make the 'perf_stats' file entirely invisible to indicate that
performance stats for an nvdimm are unavailable.
So this patch updates 'papr_nd_attribute_group' to add a 'is_visible'
callback implemented as newly introduced 'papr_nd_attribute_visible()'
that returns an appropriate mode in case performance stats aren't
supported in a given nvdimm.
Also the initialization of 'papr_scm_priv.stat_buffer_len' is moved
from papr_scm_nvdimm_init() to papr_scm_probe() so that it value is
available when 'papr_nd_attribute_visible()' is called during nvdimm
initialization.
Even though 'perf_stats' attribute is available since v5.9, there are
no known user-space tools/scripts that are dependent on presence of its
sysfs file. Hence I dont expect any user-space breakage with this
patch.
Fixes: 2d02bf835e57 ("powerpc/papr_scm: Fetch nvdimm performance stats from PHYP")
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210513092349.285021-1-vaibhav@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb5c47ced46797409f4791d0380db3116d93134c ]
Patch series "mm/debug_vm_pgtable: Some minor updates", v3.
This series contains some cleanups and new test suggestions from Catalin
from an earlier discussion.
https://lore.kernel.org/linux-mm/20201123142237.GF17833@gaia/
This patch (of 2):
This adds validation tests for dirtiness after write protect conversion
for each page table level. There are two new separate test types involved
here.
The first test ensures that a given page table entry does not become dirty
after pxx_wrprotect(). This is important for platforms like arm64 which
transfers and drops the hardware dirty bit (!PTE_RDONLY) to the software
dirty bit while making it an write protected one. This test ensures that
no fresh page table entry could be created with hardware dirty bit set.
The second test ensures that a given page table entry always preserve the
dirty information across pxx_wrprotect().
This adds two previously missing PUD level basic tests and while here
fixes pxx_wrprotect() related typos in the documentation file.
Link: https://lkml.kernel.org/r/1611137241-26220-1-git-send-email-anshuman.khandual@arm.com
Link: https://lkml.kernel.org/r/1611137241-26220-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Steven Price <steven.price@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db3a34e17433de2390eb80d436970edcebd0ca3e ]
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 148c847c9e5a54b99850617bf9c143af9a344f92 ]
pwmX_enable supports three possible values:
0: Fan control disabled. Duty cycle is fixed to 0%
1: Fan control enabled, pwm mode. Duty cycle is determined by
values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
Duty cycle is adjusted such that fan speed matches
the values in Target Count registers
The current code does not do this; instead, it mixes pwm control
configuration with fan speed monitoring configuration. Worse, it
reports that pwm control would be disabled (pwmX_enable==0) when
it is in fact enabled in pwm mode. Part of the problem may be that
the chip sets the "TACH input enable" bit on its own whenever the
mode bit is set to RPM mode, but that doesn't mean that "TACH input
enable" accurately reflects the pwm mode.
Fix it up and only handle pwm control with the pwmX_enable attributes.
In the documentation, clarify that disabling pwm control (pwmX_enable=0)
sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN
is set together with RPM_MODE.
While at it, only update the configuration register if the configuration
has changed, and only update the cached configuration if updating the
chip configuration was successful.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 897f6339893b741a5d68ae8e2475df65946041c2 ]
The MAX31790 has two sets of registers for pwm duty cycles, one to request
a duty cycle and one to read the actual current duty cycle. Both do not
have to be the same.
When reporting the pwm duty cycle to the user, the actual pwm duty cycle
from pwm duty cycle registers needs to be reported. When setting it, the
pwm target duty cycle needs to be written. Since we don't know the actual
pwm duty cycle after a target pwm duty cycle has been written, set the
valid flag to false to indicate that actual pwm duty cycle should be read
from the chip instead of using cached values.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@ceesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67a7e53d5b21f3a84efc03a4e62db7caf97841ef ]
Dependent slice segment flag for PPS control is misnamed. It should have
"enabled" at the end. It only tells if this flag is present in slice
header or not and not the actual value.
Fix this by renaming the PPS flag and introduce another flag for slice
control which tells actual value.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9acc89d31f0c94c8e573ed61f3e4340bbd526d0c upstream.
EVM_ALLOW_METADATA_WRITES is an EVM initialization flag that can be set to
temporarily disable metadata verification until all xattrs/attrs necessary
to verify an EVM portable signature are copied to the file. This flag is
cleared when EVM is initialized with an HMAC key, to avoid that the HMAC is
calculated on unverified xattrs/attrs.
Currently EVM unnecessarily denies setting this flag if EVM is initialized
with a public key, which is not a concern as it cannot be used to trust
xattrs/attrs updates. This patch removes this limitation.
Fixes: ae1ba1676b88e ("EVM: Allow userland to permit modification of EVM-protected metadata")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org # 4.16.x
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8669dbab2ae56085c128894b181c2aa50f97e368 upstream.
Patch series "Actually fix freelist pointer vs redzoning", v4.
This fixes redzoning vs the freelist pointer (both for middle-position
and very small caches). Both are "theoretical" fixes, in that I see no
evidence of such small-sized caches actually be used in the kernel, but
that's no reason to let the bugs continue to exist, especially since
people doing local development keep tripping over it. :)
This patch (of 3):
Instead of repeating "Redzone" and "Poison", clarify which sides of
those zones got tripped. Additionally fix column alignment in the
trailer.
Before:
BUG test (Tainted: G B ): Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
After:
BUG test (Tainted: G B ): Right Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
The earlier commits that slowly resulted in the "Before" reporting were:
d86bd1bece6f ("mm/slub: support left redzone")
ffc79d288000 ("slub: use print_hex_dump")
2492268472e7 ("SLUB: change error reporting format to follow lockdep loosely")
Link: https://lkml.kernel.org/r/20210608183955.280836-1-keescook@chromium.org
Link: https://lkml.kernel.org/r/20210608183955.280836-2-keescook@chromium.org
Link: https://lore.kernel.org/lkml/cfdb11d7-fb8e-e578-c939-f7f5fb69a6bd@suse.cz/
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Marco Elver <elver@google.com>
Cc: "Lin, Zhenpeng" <zplin@psu.edu>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d031d99b02eaf7363c33f5b27b38086cc8104082 upstream.
There is a fair amount of warnings when running 'make dtbs_check' with
amlogic,gx-sound-card.yaml.
Ex:
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:1: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:2: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0: [66, 0, 0] is too long
The reason is that the sound-dai phandle provided has cells, and in such
case the schema should use 'phandle-array' instead of 'phandle'.
Fixes: fd00366b8e41 ("ASoC: meson: gx: add sound card dt-binding documentation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210524093448.357140-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
