| Age | Commit message (Collapse) | Author |
|---|
|
Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Here we split the description of the external-bus@50000000 over
two description files. In the more generic db8500 description file
we only specify the external-bus. Normally this would be used to
communicate with a NOR-flash device. On the Snowball however, the
SMSC9115 Ethernet chip occupies it. In the Snowball board specific
description file is where we actually specify that it is in fact the
Ethernet device which lives here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Ensure each button is individually identifiable by using
their correct unique given device names.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Split off from the patch actually implementing the bindings]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enables the 3 UARTs found on a u8500 using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.
This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
db8500.dtsi can be used by all systems with a db8500 or
db9500 SoC, while snowball.dts is board specific.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This provides very basic Device Tree support for ST-Ericsson's
low-cost development platform, Snowball. If Device Tree for
ux500 is enabled and the correct board is configured within the
Device Tree blob, the correct *_init_machine() will be called.
This patch is based on some original work completed by:
Niklas Hernaeus <niklas.hernaeus@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
