| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.18, 2nd round:
- Fix one sparse warning on imx-weim driver.
- Fix vqmmc regulator to get UHS-I mode work on imx6ull-colibri board.
- Add missing 32.768 kHz PMIC clock for imx8mn-ddr4-evk board to fix
bd718xx-clk probe error.
* tag 'imx-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
ARM: dts: imx6ull-colibri: fix vqmmc regulator
bus: imx-weim: make symbol 'weim_of_notifier' static
Link: https://lore.kernel.org/r/20220426013427.GB14615@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit 1a67653de0dd, which caused a boot regression.
The behavior of the "drive-push-pull" in the kernel does not
match what the binding document describes. Revert Rob's patch
to make the DT match the kernel again, rather than the binding.
Link: https://lore.kernel.org/lkml/YlVAy95eF%2F9b1nmu@orome/
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede574 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd09736d ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/fixes
* 'v5.18/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO pin labeling for CON1
arm64: dts: remove cpu compatible "arm,armv8" for s4
arm64: dts: meson: remove CPU opps below 1GHz for SM1 boards
arm64: dts: meson: remove CPU opps below 1GHz for G12B boards
Link: https://lore.kernel.org/r/1132bd6e-cd29-6e58-1fae-38e074545b25@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.18:
- Increase DOMAIN_MAX_CLKS in imx8m-blk-ctrl driver to fix an ISI hang
on i.MX8MN.
- Fix spi-tx-bus-width on imx8mq-tqma8mq board.
- Fix an SGTL5000 detection issue by moving MCLK pinctrl into SGTL5000
codec node.
- Fix spi2 pin configuration on imx8mm-venice board.
- Fix SCU clock controller's compatible property for i.MX8QM.
- Fix SAI device compatible for i.MX8MN.
- A couple of fixes from Rob to address issues in boolean properties
and touchscreen property sizes.
- Fix OTG controller over-current configuration for imx8mm-venice-gw
boards.
- Fix NULL but dereferenced coccicheck error in imx-weim driver.
* tag 'imx-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
ARM: dts: imx: Fix boolean properties with values
ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode
arm64: dts: imx8mn: Fix SAI nodes
arm64: dts: imx8mq-tqma8mq: change the spi-nor tx
ARM: dts: imx6qdl-apalis: Fix sgtl5000 detection issue
soc: imx: imx8m-blk-ctrl: Fix IMX8MN_DISPBLK_PD_ISI hang
arm64: dts: imx8qm: Correct SCU clock controller's compatible property
arm64: dts: imx8mm-venice: fix spi2 pin configuration
bus: imx-weim: fix NULL but dereferenced coccicheck error
Link: https://lore.kernel.org/r/20220411024301.GH129381@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.
(Thanks to Neil Armstrong for the heads up on the position of the missing pins)
Fixes: 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Signed-off-by: Guillaume Giraudon <ggiraudon@prism19.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com
|
|
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.
The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).
Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The most specific compatible string element should be "fsl,imx8mn-sai"
on i.MX8M Nano, fix it from current "fsl,imx8mm-sai" (two Ms, likely
due to copy-paste error from i.MX8M Mini).
Fixes: 9e9860069725f ("arm64: dts: imx8mn: Add SAI nodes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This fixes the qspi read command by importing the changes from commit
04aa946d57b2 ("arm64: dts: imx8: change the spi-nor tx").
Fixes: b186b8b6e770 ("arm64: dts: freescale: add initial device tree for TQMa8Mx with i.MX8M")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk". Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .
Fixes: f2180be18a63 ("arm64: dts: imx: add imx8qm common dts file")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Amlogic s4 device is already applied, but cpu compatible 'arm,armv8'
is only valid for software models, so we remove it.
Fixes: ac4dfd0d1d35 ("arm64: dts: add support for S4 based Amlogic AQ222")
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220408070901.26446-1-xianwei.zhao@amlogic.com
|
|
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3m92Sj26/v1mLG@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3moe6Hz8ELM0iS@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3nShkFzNJaI3/Z@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Due to what looks like a copy-paste error, the ECSPI2_MISO pad is not
muxed for SPI mode and causes reads from a slave-device connected to the
SPI header to always return zero.
Configure the ECSPI2_MISO pad for SPI mode on the gw71xx, gw72xx and
gw73xx families of boards that got this wrong.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org # 5.12
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com
|
|
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e92709b ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd BergmannL
"The introduction of vmap-stack on 32-bit arm caused a regression on a
few omap3/omap4 machines that pass a stack variable into a firmware
interface.
The early pre-ACPI AMD Seattle machines have been broken for a while,
Ard Biesheuvel has a series to bring them back for now.
A few machines with multiple DMA channels used on a device have the
channels in the wrong order according to the binding, which causes a
harmless warning. Reversing the order is easier than fixing the tools
to suppress the warning"
* tag 'soc-fixes-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: ls1046a: Update i2c node dma properties
arm64: dts: ls1043a: Update i2c dma properties
ARM: dts: spear1340: Update serial node properties
ARM: dts: spear13xx: Update SPI dma properties
ARM: OMAP2+: Fix regression for smc calls for vmap stack
dt: amd-seattle: add a description of the CPUs and caches
dt: amd-seattle: disable IPMI controller and some GPIO blocks on B0
dt: amd-seattle: add description of the SATA/CCP SMMUs
dt: amd-seattle: add a description of the PCIe SMMU
dt: amd-seattle: fix PCIe legacy interrupt routing
dt: amd-seattle: upgrade AMD Seattle XGBE to new SMMU binding
dt: amd-seattle: remove Overdrive revision A0 support
dt: amd-seattle: remove Husky platform
|
|
Reorder dmas and dma-names properties for i2c controller node to make it
compliant with bindings.
Fixes: 8126d88162a5 ("arm64: dts: add QorIQ LS1046A SoC support")
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: soc@kernel.org
Link: https://lore.kernel.org/r/20220326042313.97862-5-singh.kuldeep87k@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Reorder dmas and dma-names properties for i2c controller node to make it
compliant with bindings.
Fixes: 6d453cd22357 ("arm64: dts: add Freescale LS1043a SoC support")
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: soc@kernel.org
Link: https://lore.kernel.org/r/20220326042313.97862-4-singh.kuldeep87k@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace cleanups from Eric Biederman:
"This set of changes removes tracehook.h, moves modification of all of
the ptrace fields inside of siglock to remove races, adds a missing
permission check to ptrace.c
The removal of tracehook.h is quite significant as it has been a major
source of confusion in recent years. Much of that confusion was around
task_work and TIF_NOTIFY_SIGNAL (which I have now decoupled making the
semantics clearer).
For people who don't know tracehook.h is a vestiage of an attempt to
implement uprobes like functionality that was never fully merged, and
was later superseeded by uprobes when uprobes was merged. For many
years now we have been removing what tracehook functionaly a little
bit at a time. To the point where anything left in tracehook.h was
some weird strange thing that was difficult to understand"
* tag 'ptrace-cleanups-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Remove duplicated include in ptrace.c
ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
ptrace: Return the signal to continue with from ptrace_stop
ptrace: Move setting/clearing ptrace_message into ptrace_stop
tracehook: Remove tracehook.h
resume_user_mode: Move to resume_user_mode.h
resume_user_mode: Remove #ifdef TIF_NOTIFY_RESUME in set_notify_resume
signal: Move set_notify_signal and clear_notify_signal into sched/signal.h
task_work: Decouple TIF_NOTIFY_SIGNAL and task_work
task_work: Call tracehook_notify_signal from get_signal on all architectures
task_work: Introduce task_work_pending
task_work: Remove unnecessary include from posix_timers.h
ptrace: Remove tracehook_signal_handler
ptrace: Remove arch_syscall_{enter,exit}_tracehook
ptrace: Create ptrace_report_syscall_{entry,exit} in ptrace.h
ptrace/arm: Rename tracehook_report_syscall report_syscall
ptrace: Move ptrace_report_syscall into ptrace.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are still
creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits)
vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE
serial: 8250: fix XOFF/XON sending when DMA is used
tty: serial: samsung: Add ARTPEC-8 support
dt-bindings: serial: samsung: Add ARTPEC-8 UART
serial: sc16is7xx: Clear RS485 bits in the shutdown
tty: serial: samsung: simplify getting OF match data
tty: serial: samsung: constify variables and pointers
tty: serial: samsung: constify s3c24xx_serial_drv_data members
tty: serial: samsung: constify UART name
tty: serial: samsung: constify s3c24xx_serial_drv_data
tty: serial: samsung: reduce number of casts
tty: serial: samsung: embed s3c2410_uartcfg in parent structure
tty: serial: samsung: embed s3c24xx_uart_info in parent structure
serial: 8250_tegra: mark acpi_device_id as unused with !ACPI
tty: serial: bcm63xx: use more precise Kconfig symbol
serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS
tty: serial: jsm: fix two assignments in if conditions
tty: serial: jsm: remove redundant assignments to variable linestatus
serial: 8250_mtk: make two read-only arrays static const
serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups
and new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list (a
common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: gadget: fsl_qe_udc: Add missing semicolon in qe_ep_dequeue()
dt-bindings: usb: mtk-xhci: add compatible for mt8186
usb: dwc3: Issue core soft reset before enabling run/stop
usb: gadget: Makefile: remove ccflags-y
USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
usb: gadget: eliminate anonymous module_init & module_exit
usb: usbip: eliminate anonymous module_init & module_exit
xen/usb: harden xen_hcd against malicious backends
usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
usb: dwc3: gadget: move cmd_endtransfer to extra function
usb: dwc3: gadget: ep_queue simplify isoc start condition
xen/usb: don't use arbitrary_virt_to_machine()
usb: isp1760: remove redundant max_packet() macro
usb: oxu210hp-hcd: remove redundant call to max_packet() macro
usb: common: usb-conn-gpio: Make VBUS supply completely optional
USB: storage: ums-realtek: fix error code in rts51x_read_mem()
usb: early: xhci-dbc: Fix xdbc number parsing
usb: early: xhci-dbc: Remove duplicate keep parsing
x86/tsc: Be consistent about use_tsc_delay()
usb: gadget: udc: s3c2410: remove usage of list iterator past the loop body
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild update for C11 language base from Masahiro Yamada:
"Kbuild -std=gnu11 updates for v5.18
Linus pointed out the benefits of C99 some years ago, especially
variable declarations in loops [1]. At that time, we were not ready
for the migration due to old compilers.
Recently, Jakob Koschel reported a bug in list_for_each_entry(), which
leaks the invalid pointer out of the loop [2]. In the discussion, we
agreed that the time had come. Now that GCC 5.1 is the minimum
compiler version, there is nothing to prevent us from going to
-std=gnu99, or even straight to -std=gnu11.
Discussions for a better list iterator implementation are ongoing, but
this patch set must land first"
[1] https://lore.kernel.org/all/CAHk-=wgr12JkKmRd21qh-se-_Gs69kbPgR9x4C+Es-yJV2GLkA@mail.gmail.com/
[2] https://lore.kernel.org/lkml/86C4CE7D-6D93-456B-AA82-F8ADEACA40B7@gmail.com/
* tag 'kbuild-gnu11-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Kbuild: use -std=gnu11 for KBUILD_USERCFLAGS
Kbuild: move to -std=gnu11
Kbuild: use -Wdeclaration-after-statement
Kbuild: add -Wno-shift-negative-value where -Wextra is used
|
|
Generic KASAN already selects KASAN_VMALLOC to allow VMAP_STACK to be
selected unconditionally, see commit acc3042d62cb9 ("arm64: Kconfig:
select KASAN_VMALLOC if KANSAN_GENERIC is enabled").
The same change is needed for SW_TAGS KASAN.
HW_TAGS KASAN does not require enabling KASAN_VMALLOC for VMAP_STACK, they
already work together as is. Still, selecting KASAN_VMALLOC still makes
sense to make vmalloc() always protected. In case any bugs in KASAN's
vmalloc() support are discovered, the command line kasan.vmalloc flag can
be used to disable vmalloc() checking.
Select KASAN_VMALLOC for all KASAN modes for arm64.
Link: https://lkml.kernel.org/r/99d6b3ebf57fc1930ff71f9a4a71eea19881b270.1643047180.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Besides asking vmalloc memory to be executable via the prot argument of
__vmalloc_node_range() (see the previous patch), the kernel can skip that
bit and instead mark memory as executable via set_memory_x().
Once tag-based KASAN modes start tagging vmalloc allocations, executing
code from such allocations will lead to the PC register getting a tag,
which is not tolerated by the kernel.
Generic kernel code typically allocates memory via module_alloc() if it
intends to mark memory as executable. (On arm64 module_alloc() uses
__vmalloc_node_range() without setting the executable bit).
Thus, reset pointer tags of pointers returned from module_alloc().
However, on arm64 there's an exception: the eBPF subsystem. Instead of
using module_alloc(), it uses vmalloc() (via bpf_jit_alloc_exec()) to
allocate its JIT region.
Thus, reset pointer tags of pointers returned from bpf_jit_alloc_exec().
Resetting tags for these pointers results in untagged pointers being
passed to set_memory_x(). This causes conflicts in arithmetic checks in
change_memory_common(), as vm_struct->addr pointer returned by
find_vm_area() is tagged.
Reset pointer tag of find_vm_area(addr)->addr in change_memory_common().
Link: https://lkml.kernel.org/r/b7b2595423340cd7d76b770e5d519acf3b72f0ab.1643047180.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HW_TAGS KASAN relies on ARM Memory Tagging Extension (MTE). With MTE, a
memory region must be mapped as MT_NORMAL_TAGGED to allow setting memory
tags via MTE-specific instructions.
Add proper protection bits to vmalloc() allocations. These allocations
are always backed by page_alloc pages, so the tags will actually be
getting set on the corresponding physical memory.
Link: https://lkml.kernel.org/r/983fc33542db2f6b1e77b34ca23448d4640bbb9e.1643047180.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Once tag-based KASAN modes start tagging vmalloc() allocations, kernel
stacks start getting tagged if CONFIG_VMAP_STACK is enabled.
Reset the tag of kernel stack pointers after allocation in
arch_alloc_vmap_stack().
For SW_TAGS KASAN, when CONFIG_KASAN_STACK is enabled, the instrumentation
can't handle the SP register being tagged.
For HW_TAGS KASAN, there's no instrumentation-related issues. However,
the impact of having a tagged SP register needs to be properly evaluated,
so keep it non-tagged for now.
Note, that the memory for the stack allocation still gets tagged to catch
vmalloc-into-stack out-of-bounds accesses.
[andreyknvl@google.com: fix case when a stack is retrieved from cached_stacks]
Link: https://lkml.kernel.org/r/f50c5f96ef896d7936192c888b0c0a7674e33184.1644943792.git.andreyknvl@google.com
[dan.carpenter@oracle.com: remove unnecessary check in alloc_thread_stack_node()]
Link: https://lkml.kernel.org/r/20220301080706.GB17208@kili
Link: https://lkml.kernel.org/r/698c5ab21743c796d46c15d075b9481825973e34.1643047180.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marco Elver <elver@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rename kasan_free_shadow to kasan_free_module_shadow and
kasan_module_alloc to kasan_alloc_module_shadow.
These functions are used to allocate/free shadow memory for kernel modules
when KASAN_VMALLOC is not enabled. The new names better reflect their
purpose.
Also reword the comment next to their declaration to improve clarity.
Link: https://lkml.kernel.org/r/36db32bde765d5d0b856f77d2d806e838513fe84.1643047180.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge more updates from Andrew Morton:
"Various misc subsystems, before getting into the post-linux-next
material.
41 patches.
Subsystems affected by this patch series: procfs, misc, core-kernel,
lib, checkpatch, init, pipe, minix, fat, cgroups, kexec, kdump,
taskstats, panic, kcov, resource, and ubsan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (41 commits)
Revert "ubsan, kcsan: Don't combine sanitizer with kcov on clang"
kernel/resource: fix kfree() of bootmem memory again
kcov: properly handle subsequent mmap calls
kcov: split ioctl handling into locked and unlocked parts
panic: move panic_print before kmsg dumpers
panic: add option to dump all CPUs backtraces in panic_print
docs: sysctl/kernel: add missing bit to panic_print
taskstats: remove unneeded dead assignment
kasan: no need to unset panic_on_warn in end_report()
ubsan: no need to unset panic_on_warn in ubsan_epilogue()
panic: unset panic_on_warn inside panic()
docs: kdump: add scp example to write out the dump file
docs: kdump: update description about sysfs file system support
arm64: mm: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
x86/setup: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
riscv: mm: init: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
kexec: make crashk_res, crashk_low_res and crash_notes symbols always visible
cgroup: use irqsave in cgroup_rstat_flush_locked().
fat: use pointer to simple type in put_user()
minix: fix bug when opening a file with O_DIRECT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Proper emulation of the OSLock feature of the debug architecture
- Scalibility improvements for the MMU lock when dirty logging is on
- New VMID allocator, which will eventually help with SVA in VMs
- Better support for PMUs in heterogenous systems
- PSCI 1.1 support, enabling support for SYSTEM_RESET2
- Implement CONFIG_DEBUG_LIST at EL2
- Make CONFIG_ARM64_ERRATUM_2077057 default y
- Reduce the overhead of VM exit when no interrupt is pending
- Remove traces of 32bit ARM host support from the documentation
- Updated vgic selftests
- Various cleanups, doc updates and spelling fixes
RISC-V:
- Prevent KVM_COMPAT from being selected
- Optimize __kvm_riscv_switch_to() implementation
- RISC-V SBI v0.3 support
s390:
- memop selftest
- fix SCK locking
- adapter interruptions virtualization for secure guests
- add Claudio Imbrenda as maintainer
- first step to do proper storage key checking
x86:
- Continue switching kvm_x86_ops to static_call(); introduce
static_call_cond() and __static_call_ret0 when applicable.
- Cleanup unused arguments in several functions
- Synthesize AMD 0x80000021 leaf
- Fixes and optimization for Hyper-V sparse-bank hypercalls
- Implement Hyper-V's enlightened MSR bitmap for nested SVM
- Remove MMU auditing
- Eager splitting of page tables (new aka "TDP" MMU only) when dirty
page tracking is enabled
- Cleanup the implementation of the guest PGD cache
- Preparation for the implementation of Intel IPI virtualization
- Fix some segment descriptor checks in the emulator
- Allow AMD AVIC support on systems with physical APIC ID above 255
- Better API to disable virtualization quirks
- Fixes and optimizations for the zapping of page tables:
- Zap roots in two passes, avoiding RCU read-side critical
sections that last too long for very large guests backed by 4
KiB SPTEs.
- Zap invalid and defunct roots asynchronously via
concurrency-managed work queue.
- Allowing yielding when zapping TDP MMU roots in response to the
root's last reference being put.
- Batch more TLB flushes with an RCU trick. Whoever frees the
paging structure now holds RCU as a proxy for all vCPUs running
in the guest, i.e. to prolongs the grace period on their behalf.
It then kicks the the vCPUs out of guest mode before doing
rcu_read_unlock().
Generic:
- Introduce __vcalloc and use it for very large allocations that need
memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
KVM: use kvcalloc for array allocations
KVM: x86: Introduce KVM_CAP_DISABLE_QUIRKS2
kvm: x86: Require const tsc for RT
KVM: x86: synthesize CPUID leaf 0x80000021h if useful
KVM: x86: add support for CPUID leaf 0x80000021
KVM: x86: do not use KVM_X86_OP_OPTIONAL_RET0 for get_mt_mask
Revert "KVM: x86/mmu: Zap only TDP MMU leafs in kvm_zap_gfn_range()"
kvm: x86/mmu: Flush TLB before zap_gfn_range releases RCU
KVM: arm64: fix typos in comments
KVM: arm64: Generalise VM features into a set of flags
KVM: s390: selftests: Add error memop tests
KVM: s390: selftests: Add more copy memop tests
KVM: s390: selftests: Add named stages for memop test
KVM: s390: selftests: Add macro as abstraction for MEM_OP
KVM: s390: selftests: Split memop tests
KVM: s390x: fix SCK locking
RISC-V: KVM: Implement SBI HSM suspend call
RISC-V: KVM: Add common kvm_riscv_vcpu_wfi() function
RISC-V: Add SBI HSM suspend related defines
RISC-V: KVM: Implement SBI v0.3 SRST extension
...
|
|
Add a DT description of the CPU and cache hierarchy as found on
the AMD Seattle SOC. Given the tight coupling of the PMU with
the CPUs, move the PMU node into the cpu .dtsi file as well, and
add the missing affinity description.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Disable some peripherals that are not usable on B0 silicon based
Overdrives.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add descriptions of the SMMUs that cover the SATA controller(s)
on the AMD Seattle SOC. The CCP crypto accelerator shares its
SMMU with the second SATA controller, which is only enabled on
B1 silicon.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a description of the SMMU that covers the PCIe host bridge
on AMD Seattle.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The AMD Seattle SOC can be configured to expose up to 3 PCIe root
ports, each of which is wired to 4 dedicated SPI wired interrupts
for legacy INTx support. Update the SOC DT description to reflect
this.
Fix a stale comment about the size of the MMIO64 resource window
while at it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Upgrade the DT descriptions of the AMD Seattle XGBE network
controllers to use the current SMMU bindings.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Support for AMD Seattle silicon revision A0 is no longer relevant,
since we no longer have a driver for the network controller, and
the PCIe on these boards was very unreliable. So drop the DTS
description of the A0 version of the overdrive board.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Huskyboard never made it to production, and its successor the
Celloboard was only shipped in very limited quantities with ACPI
only firmware, so the historical significance of husky.dts is
highly questionable. Let's drop it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Replace the conditional compilation using "#ifdef CONFIG_KEXEC_CORE" by a
check for "IS_ENABLED(CONFIG_KEXEC_CORE)", to simplify the code and
increase compile coverage.
Link: https://lkml.kernel.org/r/20211206160514.2000-5-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"After a somewhat quiet 5.17 release, the size of the DT changes is a
bit larger again. There are nine new SoC that get added, all of them
related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G
tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the LG Nexus
5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs, along
with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC loosely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added
all over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91,
Allwinner, i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and
Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic:
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno:
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar:
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)"
* tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (627 commits)
arm64: dts: n5x: drop invalid property and fix edac node name
arm64: dts: fsd: Add the MCT support
arm64: dts: stingray: Fix spi clock name
arm64: dts: ns2: Fix spi clock name
ARM: dts: rockchip: Update regulator name for PX3
ARM: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Remove vcc13 and vcc14 for rk808
arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
ARM: dts: at91: sama7g5: Add NAND support
ARM: dts: at91: sama7g5: add eic node
ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
ARM: dts: at91: sam9x60ek: modify vdd_1v5 regulator to vdd_1v15
arm64: dts: lg: align pl330 node name with dtschema
arm64: dts: lg: add dma-cells to pl330 node
arm64: dts: juno: align pl330 node name with dtschema
arm64: dts: broadcom: Fix sata nodename
arm64: dts: n5x: add sdr edac support
arm64: dts: agilex/stratix10: add clock-names to USB DWC2 node
dt-bindings: usb: dwc2: add disable-over-current
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM defconfig updates from Arnd Bergmann:
"Various updates for the 32-bit and 64-bit defconfig files, mostly to
enable additional hardware drivers for more machines, specifically for
the Allwinner F1C100, Altera SoCFPGA, Broadcom, Microchip, Qualcomm,
Airoha, Tegra, Renesas, and i.NX.
The multi_v5_defconfig for older ARMv5 configs gets a rework for Andre
Przywara to cleans up the multi_v5_defconfig for some cruft that has
accumulated and drivers that got disabled unintentionally, while
Anders Roxell makes it more useful for running under Qemu"
* tag 'arm-defconfig-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (41 commits)
ARM: configs: multi_v5: Enable Allwinner F1C100
ARM: configs: clean up multi_v5_defconfig
ARM: configs: multi_v5_defconfig: re-enable DRM_PANEL and FB_xxx
ARM: configs: multi_v5_defconfig: re-enable CONFIG_V4L_PLATFORM_DRIVERS
ARM: configs: multi_v5_defconfig: remove deleted platforms
ARM: defconfig: add SMB347 charger driver for p4note
arm: multi_v5: enable configs for versatile
arm64: defconfig: enable Layerscape SFP driver
ARM: configs: at91: sama7: Unselect CONFIG_DMATEST
ARM: configs: at91: add eic
arm64: defconfig: enable the CVP driver
ARM: multi_v7_defconfig: Add support for Airoha EN7523 SoC
ARM: multi_v7_defconfig: Enable BCM23550 and BCM53573
ARM: multi_v7_defconfig: Enable Broadcom STB USB drivers
ARM: configs: at91: sama7: add config for cpufreq
ARM: configs: at91: sama7: enable cpu idle
ARM: configs: at91: sama7: Enable crypto IPs and software algs
ARM: configs: at91: sama7: Enable UBIFS_FS
ARM: configs: at91: sama7: Enable NAND / SMC
arm64: defconfig: tegra: Enable GPCDMA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
|
|
Pull folio updates from Matthew Wilcox:
- Rewrite how munlock works to massively reduce the contention on
i_mmap_rwsem (Hugh Dickins):
https://lore.kernel.org/linux-mm/8e4356d-9622-a7f0-b2c-f116b5f2efea@google.com/
- Sort out the page refcount mess for ZONE_DEVICE pages (Christoph
Hellwig):
https://lore.kernel.org/linux-mm/20220210072828.2930359-1-hch@lst.de/
- Convert GUP to use folios and make pincount available for order-1
pages. (Matthew Wilcox)
- Convert a few more truncation functions to use folios (Matthew
Wilcox)
- Convert page_vma_mapped_walk to use PFNs instead of pages (Matthew
Wilcox)
- Convert rmap_walk to use folios (Matthew Wilcox)
- Convert most of shrink_page_list() to use a folio (Matthew Wilcox)
- Add support for creating large folios in readahead (Matthew Wilcox)
* tag 'folio-5.18c' of git://git.infradead.org/users/willy/pagecache: (114 commits)
mm/damon: minor cleanup for damon_pa_young
selftests/vm/transhuge-stress: Support file-backed PMD folios
mm/filemap: Support VM_HUGEPAGE for file mappings
mm/readahead: Switch to page_cache_ra_order
mm/readahead: Align file mappings for non-DAX
mm/readahead: Add large folio readahead
mm: Support arbitrary THP sizes
mm: Make large folios depend on THP
mm: Fix READ_ONLY_THP warning
mm/filemap: Allow large folios to be added to the page cache
mm: Turn can_split_huge_page() into can_split_folio()
mm/vmscan: Convert pageout() to take a folio
mm/vmscan: Turn page_check_references() into folio_check_references()
mm/vmscan: Account large folios correctly
mm/vmscan: Optimise shrink_page_list for non-PMD-sized folios
mm/vmscan: Free non-shmem folios without splitting them
mm/rmap: Constify the rmap_walk_control argument
mm/rmap: Convert rmap_walk() to take a folio
mm: Turn page_anon_vma() into folio_anon_vma()
mm/rmap: Turn page_lock_anon_vma_read() into folio_lock_anon_vma_read()
...
|
|
Merge updates from Andrew Morton:
- A few misc subsystems: kthread, scripts, ntfs, ocfs2, block, and vfs
- Most the MM patches which precede the patches in Willy's tree: kasan,
pagecache, gup, swap, shmem, memcg, selftests, pagemap, mremap,
sparsemem, vmalloc, pagealloc, memory-failure, mlock, hugetlb,
userfaultfd, vmscan, compaction, mempolicy, oom-kill, migration, thp,
cma, autonuma, psi, ksm, page-poison, madvise, memory-hotplug, rmap,
zswap, uaccess, ioremap, highmem, cleanups, kfence, hmm, and damon.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (227 commits)
mm/damon/sysfs: remove repeat container_of() in damon_sysfs_kdamond_release()
Docs/ABI/testing: add DAMON sysfs interface ABI document
Docs/admin-guide/mm/damon/usage: document DAMON sysfs interface
selftests/damon: add a test for DAMON sysfs interface
mm/damon/sysfs: support DAMOS stats
mm/damon/sysfs: support DAMOS watermarks
mm/damon/sysfs: support schemes prioritization
mm/damon/sysfs: support DAMOS quotas
mm/damon/sysfs: support DAMON-based Operation Schemes
mm/damon/sysfs: support the physical address space monitoring
mm/damon/sysfs: link DAMON for virtual address spaces monitoring
mm/damon: implement a minimal stub for sysfs-based DAMON interface
mm/damon/core: add number of each enum type values
mm/damon/core: allow non-exclusive DAMON start/stop
Docs/damon: update outdated term 'regions update interval'
Docs/vm/damon/design: update DAMON-Idle Page Tracking interference handling
Docs/vm/damon: call low level monitoring primitives the operations
mm/damon: remove unnecessary CONFIG_DAMON option
mm/damon/paddr,vaddr: remove damon_{p,v}a_{target_valid,set_operations}()
mm/damon/dbgfs-test: fix is_target_id() change
...
|
|
node_dev_init()
... and call node_dev_init() after memory_dev_init() from driver_init(),
so before any of the existing arch/subsys calls. All online nodes should
be known at that point: early during boot, arch code determines node and
zone ranges and sets the relevant nodes online; usually this happens in
setup_arch().
This is in line with memory_dev_init(), which initializes the memory
device subsystem and creates all memory block devices.
Similar to memory_dev_init(), panic() if anything goes wrong, we don't
want to continue with such basic initialization errors.
The important part is that node_dev_init() gets called after
memory_dev_init() and after cpu_dev_init(), but before any of the relevant
archs call register_cpu() to register the new cpu device under the node
device. The latter should be the case for the current users of
topology_init().
Link: https://lkml.kernel.org/r/20220203105212.30385-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Tested-by: Anatoly Pugachev <matorola@gmail.com> (sparc64)
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
