summaryrefslogtreecommitdiff
path: root/arch/mips/rb532/devices.c
AgeCommit message (Collapse)Author
2012-06-01Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull mtd update from David Woodhouse: - More robust parsing especially of xattr data in JFFS2 - Updates to mxc_nand and gpmi drivers to support new boards and device tree - Improve consistency of information about ECC strength in NAND devices - Clean up partition handling of plat_nand - Support NAND drivers without dedicated access to OOB area - BCH hardware ECC support for OMAP - Other fixes and cleanups, and a few new device IDs Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to added include files next to each other. * tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits) mtd: mxc_nand: move ecc strengh setup before nand_scan_tail mtd: block2mtd: fix recursive call of mtd_writev mtd: gpmi-nand: define ecc.strength mtd: of_parts: fix breakage in Kconfig mtd: nand: fix scan_read_raw_oob mtd: docg3 fix in-middle of blocks reads mtd: cfi_cmdset_0002: Slight cleanup of fixup messages mtd: add fixup for S29NS512P NOR flash. jffs2: allow to complete xattr integrity check on first GC scan jffs2: allow to discriminate between recoverable and non-recoverable errors mtd: nand: omap: add support for hardware BCH ecc ARM: OMAP3: gpmc: add BCH ecc api and modes mtd: nand: check the return code of 'read_oob/read_oob_raw' mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw' mtd: m25p80: Add support for Winbond W25Q80BW jffs2: get rid of jffs2_sync_super jffs2: remove unnecessary GC pass on sync jffs2: remove unnecessary GC pass on umount jffs2: remove lock_super mtd: gpmi: add gpmi support for mx6q ...
2012-05-15MIPS: Fix several implicit uses of export.h/module.hPaul Gortmaker
These will show up as a build failure once we clean up a misuse of module.h in the mips termios header. Uses export.h: (EXPORT_SYMBOL) arch/mips/cavium-octeon/setup.c arch/mips/pmc-sierra/yosemite/setup.c arch/mips/rb532/devices.c arch/mips/sni/setup.c Uses module.h: (symbol_get/put) arch/mips/alchemy/devboards/db1200.c Uses module.h: (print_modules) arch/mips/kernel/traps.c Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/3448/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-05-13mtd: nand: kill NAND_NO_AUTOINCR optionBrian Norris
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-07-25MIPS: RB532: Use hex_to_bin()Andy Shevchenko
Remove custom implementation of hex_to_bin(). Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org To: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/1580/ Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-02MIPS: RB532: Fix devices.c compilation.Florian Fainelli
We should now use dev_set_drvdata to set the driver driver_data field. Signed-off-by: Florian Fainelli <florian@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/747/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-03-09Input: add driver for S1 button of rb532Phil Sutter
Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-01-30MIPS: RB532: Simplify dev3 initPhil Sutter
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped when not used for holding the physical address of the device 3 controller. Also a size of one byte should suffice when ioremapping the physical address mentioned above, as only a single byte is being read from and written to it. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30MIPS: RB532: Move dev3 init code to devices.cPhil Sutter
This code doesn't belong to gpio.c, as it's completely unrelated to GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more adequate place. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30MIPS: RB532: Use driver_data instead of platform_dataPhil Sutter
As the korina ethernet driver uses platform_get_drvdata() to extract the driver specific data from the platform device, driver_data has to be used here. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30MIPS: RB532: Detect uart type, add platform devicePhil Sutter
Auto-detection works just fine, so use it instead of specifying the type manually. Also define a platform device for the uart, as suggested by David Daney. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-11-20MIPS: RB532: GPIO register offsets are relative to GPIOBASEFlorian Fainelli
This patch fixes the wrong use of GPIO register offsets in devices.c. To avoid further problems, use gpio_get_value to return the NAND status instead of our own expanded code. Also define the zero offset of the alternate function register to allow consistent access. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-27MIPS: RB532: Disable the right devicePhil Sutter
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11MIPS: RB532: Fix id usage in platform devicesFlorian Fainelli
When there is only platform device of the same type, id = -1 should be used, fix this. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11MIPS: RB532: Cleanup and group definitions to their right placesFlorian Fainelli
This patch moves GPIO related definitions to gpio.h and IRQ related to irq.h Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-08-26[MIPS] RB532: Do not define registers that are already definedFlorian Fainelli
Use the register definitions of the MPMC controller from mach-rc32434/rb.h instead of redefining them. Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-07-20[MIPS] Routerboard 532: Support for base systemRalf Baechle
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-06 18:06:09 +0000