summaryrefslogtreecommitdiff
path: root/arch/x86/kvm
AgeCommit message (Collapse)Author
2008-07-29KVM: Advertise synchronized mmu support to userspaceAvi Kivity
Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-29KVM: Synchronize guest physical memory map to host virtual memory mapAndrea Arcangeli
Synchronize changes to host virtual addresses which are part of a KVM memory slot to the KVM shadow mmu. This allows pte operations like swapping, page migration, and madvise() to transparently work with KVM. Signed-off-by: Andrea Arcangeli <andrea@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-29KVM: Allow browsing memslots with mmu_lockAndrea Arcangeli
This allows reading memslots with only the mmu_lock hold for mmu notifiers that runs in atomic context and with mmu_lock held. Signed-off-by: Andrea Arcangeli <andrea@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-29KVM: Allow reading aliases with mmu_lockAndrea Arcangeli
This allows the mmu notifier code to run unalias_gfn with only the mmu_lock held. Only alias writes need the mmu_lock held. Readers will either take the slots_lock in read mode or the mmu_lock. Signed-off-by: Andrea Arcangeli <andrea@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-28mmu-notifiers: coreAndrea Arcangeli
With KVM/GFP/XPMEM there isn't just the primary CPU MMU pointing to pages. There are secondary MMUs (with secondary sptes and secondary tlbs) too. sptes in the kvm case are shadow pagetables, but when I say spte in mmu-notifier context, I mean "secondary pte". In GRU case there's no actual secondary pte and there's only a secondary tlb because the GRU secondary MMU has no knowledge about sptes and every secondary tlb miss event in the MMU always generates a page fault that has to be resolved by the CPU (this is not the case of KVM where the a secondary tlb miss will walk sptes in hardware and it will refill the secondary tlb transparently to software if the corresponding spte is present). The same way zap_page_range has to invalidate the pte before freeing the page, the spte (and secondary tlb) must also be invalidated before any page is freed and reused. Currently we take a page_count pin on every page mapped by sptes, but that means the pages can't be swapped whenever they're mapped by any spte because they're part of the guest working set. Furthermore a spte unmap event can immediately lead to a page to be freed when the pin is released (so requiring the same complex and relatively slow tlb_gather smp safe logic we have in zap_page_range and that can be avoided completely if the spte unmap event doesn't require an unpin of the page previously mapped in the secondary MMU). The mmu notifiers allow kvm/GRU/XPMEM to attach to the tsk->mm and know when the VM is swapping or freeing or doing anything on the primary MMU so that the secondary MMU code can drop sptes before the pages are freed, avoiding all page pinning and allowing 100% reliable swapping of guest physical address space. Furthermore it avoids the code that teardown the mappings of the secondary MMU, to implement a logic like tlb_gather in zap_page_range that would require many IPI to flush other cpu tlbs, for each fixed number of spte unmapped. To make an example: if what happens on the primary MMU is a protection downgrade (from writeable to wrprotect) the secondary MMU mappings will be invalidated, and the next secondary-mmu-page-fault will call get_user_pages and trigger a do_wp_page through get_user_pages if it called get_user_pages with write=1, and it'll re-establishing an updated spte or secondary-tlb-mapping on the copied page. Or it will setup a readonly spte or readonly tlb mapping if it's a guest-read, if it calls get_user_pages with write=0. This is just an example. This allows to map any page pointed by any pte (and in turn visible in the primary CPU MMU), into a secondary MMU (be it a pure tlb like GRU, or an full MMU with both sptes and secondary-tlb like the shadow-pagetable layer with kvm), or a remote DMA in software like XPMEM (hence needing of schedule in XPMEM code to send the invalidate to the remote node, while no need to schedule in kvm/gru as it's an immediate event like invalidating primary-mmu pte). At least for KVM without this patch it's impossible to swap guests reliably. And having this feature and removing the page pin allows several other optimizations that simplify life considerably. Dependencies: 1) mm_take_all_locks() to register the mmu notifier when the whole VM isn't doing anything with "mm". This allows mmu notifier users to keep track if the VM is in the middle of the invalidate_range_begin/end critical section with an atomic counter incraese in range_begin and decreased in range_end. No secondary MMU page fault is allowed to map any spte or secondary tlb reference, while the VM is in the middle of range_begin/end as any page returned by get_user_pages in that critical section could later immediately be freed without any further ->invalidate_page notification (invalidate_range_begin/end works on ranges and ->invalidate_page isn't called immediately before freeing the page). To stop all page freeing and pagetable overwrites the mmap_sem must be taken in write mode and all other anon_vma/i_mmap locks must be taken too. 2) It'd be a waste to add branches in the VM if nobody could possibly run KVM/GRU/XPMEM on the kernel, so mmu notifiers will only enabled if CONFIG_KVM=m/y. In the current kernel kvm won't yet take advantage of mmu notifiers, but this already allows to compile a KVM external module against a kernel with mmu notifiers enabled and from the next pull from kvm.git we'll start using them. And GRU/XPMEM will also be able to continue the development by enabling KVM=m in their config, until they submit all GRU/XPMEM GPLv2 code to the mainline kernel. Then they can also enable MMU_NOTIFIERS in the same way KVM does it (even if KVM=n). This guarantees nobody selects MMU_NOTIFIER=y if KVM and GRU and XPMEM are all =n. The mmu_notifier_register call can fail because mm_take_all_locks may be interrupted by a signal and return -EINTR. Because mmu_notifier_reigster is used when a driver startup, a failure can be gracefully handled. Here an example of the change applied to kvm to register the mmu notifiers. Usually when a driver startups other allocations are required anyway and -ENOMEM failure paths exists already. struct kvm *kvm_arch_create_vm(void) { struct kvm *kvm = kzalloc(sizeof(struct kvm), GFP_KERNEL); + int err; if (!kvm) return ERR_PTR(-ENOMEM); INIT_LIST_HEAD(&kvm->arch.active_mmu_pages); + kvm->arch.mmu_notifier.ops = &kvm_mmu_notifier_ops; + err = mmu_notifier_register(&kvm->arch.mmu_notifier, current->mm); + if (err) { + kfree(kvm); + return ERR_PTR(err); + } + return kvm; } mmu_notifier_unregister returns void and it's reliable. The patch also adds a few needed but missing includes that would prevent kernel to compile after these changes on non-x86 archs (x86 didn't need them by luck). [akpm@linux-foundation.org: coding-style fixes] [akpm@linux-foundation.org: fix mm/filemap_xip.c build] [akpm@linux-foundation.org: fix mm/mmu_notifier.c build] Signed-off-by: Andrea Arcangeli <andrea@qumranet.com> Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Christoph Lameter <cl@linux-foundation.org> Cc: Jack Steiner <steiner@sgi.com> Cc: Robin Holt <holt@sgi.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Kanoj Sarcar <kanojsarcar@yahoo.com> Cc: Roland Dreier <rdreier@cisco.com> Cc: Steve Wise <swise@opengridcomputing.com> Cc: Avi Kivity <avi@qumranet.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Anthony Liguori <aliguori@us.ibm.com> Cc: Chris Wright <chrisw@redhat.com> Cc: Marcelo Tosatti <marcelo@kvack.org> Cc: Eric Dumazet <dada1@cosmosbay.com> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Cc: Izik Eidus <izike@qumranet.com> Cc: Anthony Liguori <aliguori@us.ibm.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-27KVM: VMX: Fix undefined beaviour of EPT after reload kvm-intel.koSheng Yang
As well as move set base/mask ptes to vmx_init(). Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: VMX: Fix bypass_guest_pf enabling when disable EPT in module parameterSheng Yang
Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: task switch: translate guest segment limit to virt-extension byte ↵Marcelo Tosatti
granular field If 'g' is one then limit is 4kb granular. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: Avoid instruction emulation when event delivery is pendingAvi Kivity
When an event (such as an interrupt) is injected, and the stack is shadowed (and therefore write protected), the guest will exit. The current code will see that the stack is shadowed and emulate a few instructions, each time postponing the injection. Eventually the injection may succeed, but at that time the guest may be unwilling to accept the interrupt (for example, the TPR may have changed). This occurs every once in a while during a Windows 2008 boot. Fix by unshadowing the fault address if the fault was due to an event injection. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: task switch: use seg regs provided by subarch instead of reading from GDTMarcelo Tosatti
There is no guarantee that the old TSS descriptor in the GDT contains the proper base address. This is the case for Windows installation's reboot-via-triplefault. Use guest registers instead. Also translate the address properly. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: task switch: segment base is linear addressMarcelo Tosatti
The segment base is always a linear address, so translate before accessing guest memory. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-27KVM: SVM: allow enabling/disabling NPT by reloading only the architecture moduleJoerg Roedel
If NPT is enabled after loading both KVM modules on AMD and it should be disabled, both KVM modules must be reloaded. If only the architecture module is reloaded the behavior is undefined. With this patch it is possible to disable NPT only by reloading the kvm_amd module. Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: Fix potential race setting upper shadow ptes on nonpae hostsAvi Kivity
The direct mapped shadow code (used for real mode and two dimensional paging) sets upper-level ptes using direct assignment rather than calling set_shadow_pte(). A nonpae host will split this into two writes, which opens up a race if another vcpu accesses the same memory area. Fix by calling set_shadow_pte() instead of assigning directly. Noticed by Izik Eidus. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: emulate clflushGlauber Costa
If the guest issues a clflush in a mmio address, the instruction can trap into the hypervisor. Currently, we do not decode clflush properly, causing the guest to hang. This patch fixes this emulating clflush (opcode 0f ae). Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: improve invalid shadow root page handlingMarcelo Tosatti
Harden kvm_mmu_zap_page() against invalid root pages that had been shadowed from memslots that are gone. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: nuke shadowed pgtable pages and ptes on memslot destructionMarcelo Tosatti
Flush the shadow mmu before removing regions to avoid stale entries. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: Prefix some x86 low level function with kvm_, to avoid namespace issuesAvi Kivity
Fixes compilation with CONFIG_VMI enabled. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: check injected pic irq within valid pic irqsBen-Ami Yassour
Check that an injected pic irq is between 0 and 15. Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: Fix HLT instructionMohammed Gamal
This patch fixes issue encountered with HLT instruction under FreeDOS's HIMEM XMS Driver. The HLT instruction jumped directly to the done label and skips updating the EIP value, therefore causing the guest to spin endlessly on the same instruction. The patch changes the instruction so that it writes back the updated EIP value. Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: Apply the kernel sigmask to vcpus blocked due to being uninitializedAvi Kivity
Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: VMX: Add ept_sync_context in flush_tlbSheng Yang
Fix a potention issue caused by kvm_mmu_slot_remove_write_access(). The old behavior don't sync EPT TLB with modified EPT entry, which result in inconsistent content of EPT TLB and EPT table. Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: mmu_shrink: kvm_mmu_zap_page requires slots_lock to be heldMarcelo Tosatti
kvm_mmu_zap_page() needs slots lock held (rmap_remove->gfn_to_memslot, for example). Since kvm_lock spinlock is held in mmu_shrink(), do a non-blocking down_read_trylock(). Untested. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: SVM: fix suspend/resume supportJoerg Roedel
On suspend the svm_hardware_disable function is called which frees all svm_data variables. On resume they are not re-allocated. This patch removes the deallocation of svm_data from the hardware_disable function to the hardware_unsetup function which is not called on suspend. Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: move slots_lock acquision down to vapic_exitMarcelo Tosatti
There is no need to grab slots_lock if the vapic_page will not be touched. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: VMX: Fake emulate Intel perfctr MSRsChris Lalancette
Older linux guests (in this case, 2.6.9) can attempt to access the performance counter MSRs without a fixup section, and injecting a GPF kills the guest. Work around by allowing the guest to write those MSRs. Tested by me on RHEL-4 i386 and x86_64 guests, as well as F-9 guests. Signed-off-by: Chris Lalancette <clalance@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: VMX: Fix a wrong usage of vmcs_configSheng Yang
The function ept_update_paging_mode_cr0() write to CPU_BASED_VM_EXEC_CONTROL based on vmcs_config.cpu_based_exec_ctrl. That's wrong because the variable may not consistent with the content in the CPU_BASE_VM_EXEC_CONTROL MSR. Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: Fix printk formatAvi Kivity
Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: When debug is enabled, make it a run-time parameterAvi Kivity
Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: lazily evaluate segment registersAvi Kivity
Instead of prefetching all segment bases before emulation, read them at the last moment. Since most of them are unneeded, we save some cycles on Intel machines where this is a bit expensive. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: avoid segment base adjust for leaAvi Kivity
Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: simplify rip relative decodingAvi Kivity
rip relative decoding is relative to the instruction pointer of the next instruction; by moving address adjustment until after decoding is complete, we remove the need to determine the instruction size. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: simplify r/m decodingAvi Kivity
Consolidate the duplicated code when not in any special case. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: simplify sib decodingAvi Kivity
Instead of using sparse switches, use simpler if/else sequences. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: handle undecoded rex.b with r/m = 5 in certain casesAvi Kivity
x86_64 does not decode rex.b in certain cases, where the r/m field = 5. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: emulate nop and xchg reg, acc (opcodes 0x90 - 0x97)Mohammed Gamal
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: Use printk_rlimit() instead of reporting emulation failures just onceAvi Kivity
Emulation failure reports are useful, so allow more than one per the lifetime of the module. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: Do not calculate linear rip in emulation failure reportGlauber Costa
If we're not gonna do anything (case in which failure is already reported), we do not need to even bother with calculating the linear rip. Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: only abort guest entry if timer count goes from 0->1Marcelo Tosatti
Only abort guest entry if the timer count went from 0->1, since for 1->2 or larger the bit will either be set already or a timer irq will have been injected. Using atomic_inc_and_test() for it also introduces an SMP barrier to the LAPIC version (thought it was unecessary because of timer migration, but guest can be scheduled to a different pCPU between exit and kvm_vcpu_block(), so there is the possibility for a race). Noticed by Avi. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: Add coalesced MMIO support (x86 part)Laurent Vivier
This patch enables coalesced MMIO for x86 architecture. It defines KVM_MMIO_PAGE_OFFSET and KVM_CAP_COALESCED_MMIO. It enables the compilation of coalesced_mmio.c. Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: kvm_io_device: extend in_range() to manage len and write attributeLaurent Vivier
Modify member in_range() of structure kvm_io_device to pass length and the type of the I/O (write or read). This modification allows to use kvm_io_device with coalesced MMIO. Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: Avoid page prefetch on SVMAvi Kivity
SVM cannot benefit from page prefetching since guest page fault bypass cannot by made to work there. Avoid accessing the guest page table in this case. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: Move nonpaging_prefetch_page()Avi Kivity
In preparation for next patch. No code change. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: implement 'push imm' (opcode 0x68)Avi Kivity
Encountered in FC6 boot sequence, now that we don't force ss.rpl = 0 during the protected mode transition. Not really necessary, but nice to have. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: simplify push imm8 emulationAvi Kivity
Instead of fetching the data explicitly, use SrcImmByte. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: MMU: Optimize prefetch_page()Avi Kivity
Instead of reading each pte individually, read 256 bytes worth of ptes and batch process them. Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: Add support for mov r, sreg (0x8c) instructionGuillaume Thouvenin
Add support for mov r, sreg (0x8c) instruction Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net> Signed-off-by: Laurent Vivier <laurent.vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: Add support for mov seg, r (0x8e) instructionGuillaume Thouvenin
Add support for mov r, sreg (0x8c) instruction. [avi: drop the sreg decoding table in favor of 1:1 encoding] Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net> Signed-off-by: Laurent Vivier <laurent.vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: adds support to mov r,imm (opcode 0xb8) instructionGuillaume Thouvenin
Add support to mov r, imm (0xb8) instruction. Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net> Signed-off-by: Laurent Vivier <laurent.vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: add support for jmp far 0xeaGuillaume Thouvenin
Add support for jmp far (opcode 0xea) instruction. Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net> Signed-off-by: Laurent Vivier <laurent.vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-20KVM: x86 emulator: Update c->dst.bytes in decode instructionGuillaume Thouvenin
Update c->dst.bytes in decode instruction instead of instruction itself. It's needed because if c->dst.bytes is equal to 0, the instruction is not emulated. Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net> Signed-off-by: Laurent Vivier <laurent.vivier@bull.net> Signed-off-by: Avi Kivity <avi@qumranet.com>