summaryrefslogtreecommitdiff
path: root/drivers/bcma/Makefile
AgeCommit message (Collapse)Author
2014-09-09bcma: add support for chipcommon B coreHauke Mehrtens
This core is used on BCM4708 to configure the PCIe and USB3 PHYs and it contains the addresses to the Device Management unit. This will be used by the PCIe driver first. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-07bcma: add driver for PCIe Gen 2 coreRafał Miłecki
New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be initialized differently. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-11-21bcma: add GPIO driverHauke Mehrtens
Register a GPIO driver to access the GPIOs provided by the chip. The GPIOs of the SoC should always start at 0 and the other GPIOs could start at a random position. There is just one SoC in a system and when they start at 0 the number is predictable. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4587 Acked-by: Florian Fainelli <florian@openwrt.org>
2012-07-17bcma: add place for flash memory supportRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12bcma: add trivial GBIT MAC COMMON driverRafał Miłecki
GMAC COMMON core is present on BCM4706 and is used for example to access board PHYs (PHYs can not be accessed directly using GBIT MAC core). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08bcma: add mips driverHauke Mehrtens
This adds a mips driver to bcma. This is only found on embedded devices. For now the driver just initializes the irqs used on this system. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08bcma: add SOC busHauke Mehrtens
This patch adds support for using bcma on a Broadcom SoC as the system bus. An SoC like the bcm4716 could register this bus and use it to searches for the bcma cores and register the devices on this bus. BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC is a better name. Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07bcma: detect PCI core working in hostmodeRafał Miłecki
We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03bcma: read SPROM and extract MAC from itRafał Miłecki
In case of BCMA cards SPROM is located in the ChipCommon core, it is not mapped as separated host window. So far we have met only SPROMs rev 8. SPROM layout seems to be the same as for SSB buses, so we decided to share SPROM struct and some defines. For now we extract MAC address only, this can be improved of course. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-10bcma: add Broadcom specific AMBA bus driverRafał Miłecki
Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>