| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add virtual-address based lskcipher interface
- Optimise ahash/shash performance in light of costly indirect calls
- Remove ahash alignmask attribute
Algorithms:
- Improve AES/XTS performance of 6-way unrolling for ppc
- Remove some uses of obsolete algorithms (md4, md5, sha1)
- Add FIPS 202 SHA-3 support in pkcs1pad
- Add fast path for single-page messages in adiantum
- Remove zlib-deflate
Drivers:
- Add support for S4 in meson RNG driver
- Add STM32MP13x support in stm32
- Add hwrng interface support in qcom-rng
- Add support for deflate algorithm in hisilicon/zip"
* tag 'v6.7-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (283 commits)
crypto: adiantum - flush destination page before unmapping
crypto: testmgr - move pkcs1pad(rsa,sha3-*) to correct place
Documentation/module-signing.txt: bring up to date
module: enable automatic module signing with FIPS 202 SHA-3
crypto: asymmetric_keys - allow FIPS 202 SHA-3 signatures
crypto: rsa-pkcs1pad - Add FIPS 202 SHA-3 support
crypto: FIPS 202 SHA-3 register in hash info for IMA
x509: Add OIDs for FIPS 202 SHA-3 hash and signatures
crypto: ahash - optimize performance when wrapping shash
crypto: ahash - check for shash type instead of not ahash type
crypto: hash - move "ahash wrapping shash" functions to ahash.c
crypto: talitos - stop using crypto_ahash::init
crypto: chelsio - stop using crypto_ahash::init
crypto: ahash - improve file comment
crypto: ahash - remove struct ahash_request_priv
crypto: ahash - remove crypto_ahash_alignmask
crypto: gcm - stop using alignmask of ahash
crypto: chacha20poly1305 - stop using alignmask of ahash
crypto: ccm - stop using alignmask of ahash
net: ipv6: stop checking crypto_ahash_alignmask
...
|
|
Pull IPMI update from Corey Minyard:
"Only one change, and I would normally just wait, but it will make the
people trying to get rid of strncpy happy. Its a good change, anyway"
* tag 'for-linus-6.7-1' of https://github.com/cminyard/linux-ipmi:
ipmi: refactor deprecated strncpy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"To help make the move of sysctls out of kernel/sysctl.c not incur a
size penalty sysctl has been changed to allow us to not require the
sentinel, the final empty element on the sysctl array. Joel Granados
has been doing all this work. On the v6.6 kernel we got the major
infrastructure changes required to support this. For v6.7-rc1 we have
all arch/ and drivers/ modified to remove the sentinel. Both arch and
driver changes have been on linux-next for a bit less than a month. It
is worth re-iterating the value:
- this helps reduce the overall build time size of the kernel and run
time memory consumed by the kernel by about ~64 bytes per array
- the extra 64-byte penalty is no longer inncurred now when we move
sysctls out from kernel/sysctl.c to their own files
For v6.8-rc1 expect removal of all the sentinels and also then the
unneeded check for procname == NULL.
The last two patches are fixes recently merged by Krister Johansen
which allow us again to use softlockup_panic early on boot. This used
to work but the alias work broke it. This is useful for folks who want
to detect softlockups super early rather than wait and spend money on
cloud solutions with nothing but an eventual hung kernel. Although
this hadn't gone through linux-next it's also a stable fix, so we
might as well roll through the fixes now"
* tag 'sysctl-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: (23 commits)
watchdog: move softlockup_panic back to early_param
proc: sysctl: prevent aliased sysctls from getting passed to init
intel drm: Remove now superfluous sentinel element from ctl_table array
Drivers: hv: Remove now superfluous sentinel element from ctl_table array
raid: Remove now superfluous sentinel element from ctl_table array
fw loader: Remove the now superfluous sentinel element from ctl_table array
sgi-xp: Remove the now superfluous sentinel element from ctl_table array
vrf: Remove the now superfluous sentinel element from ctl_table array
char-misc: Remove the now superfluous sentinel element from ctl_table array
infiniband: Remove the now superfluous sentinel element from ctl_table array
macintosh: Remove the now superfluous sentinel element from ctl_table array
parport: Remove the now superfluous sentinel element from ctl_table array
scsi: Remove now superfluous sentinel element from ctl_table array
tty: Remove now superfluous sentinel element from ctl_table array
xen: Remove now superfluous sentinel element from ctl_table array
hpet: Remove now superfluous sentinel element from ctl_table array
c-sky: Remove now superfluous sentinel element from ctl_talbe array
powerpc: Remove now superfluous sentinel element from ctl_table arrays
riscv: Remove now superfluous sentinel element from ctl_table array
x86/vdso: Remove now superfluous sentinel element from ctl_table array
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 removal and asm-generic updates from Arnd Bergmann:
- The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will be
maintained as an LTS kernel.
- The architecture specific system call tables are updated for the
added map_shadow_stack() syscall and to remove references to the
long-gone sys_lookup_dcookie() syscall.
* tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
hexagon: Remove unusable symbols from the ptrace.h uapi
asm-generic: Fix spelling of architecture
arch: Reserve map_shadow_stack() syscall number for all architectures
syscalls: Cleanup references to sys_lookup_dcookie()
Documentation: Drop or replace remaining mentions of IA64
lib/raid6: Drop IA64 support
Documentation: Drop IA64 from feature descriptions
kernel: Drop IA64 support from sig_fault handlers
arch: Remove Itanium (IA-64) architecture
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Usual fixes and updates:
- Add up to 12 nops after TLB inserts for PA8x00 CPUs as the
specification requires (Dave Anglin)
- Simplify the parisc smp_prepare_boot_cpu() code (Russell King)
- Use 64-bit little-endian values in SBA IOMMU PDIR table for AGP
Since there is upcoming support for booting a 64-bit kernel on QEMU,
some corner cases were fixed and improvements added:
- Fix 64-bit kernel crash in STI (graphics console) font setup code
which miscalculated the font start address as it gets signed vs
unsigned offsets wrong
- Support building an uncompressed Linux kernel
- Add support for soft power-off in qemu"
* tag 'parisc-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
fbdev: stifb: Make the STI next font pointer a 32-bit signed offset
parisc: Show default CPU PSW.W setting as reported by PDC
parisc/pdc: Add width field to struct pdc_model
parisc: Add nop instructions after TLB inserts
parisc: simplify smp_prepare_boot_cpu()
parisc/agp: Use 64-bit LE values in SBA IOMMU PDIR table
parisc/firmware: Use PDC constants for narrow/wide firmware
parisc: Move parisc_narrow_firmware variable to header file
parisc/power: Trivial whitespace cleanups and license update
parisc/power: Add power soft-off when running on qemu
parisc: Allow building uncompressed Linux kernel
parisc: Add some missing PDC functions and constants
parisc: sba-iommu: Fix comment when calculating IOC number
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
|
|
The PDIR table of the System Bus Adapter (SBA) I/O MMU uses 64-bit
little-endian pointers.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.4+
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct port_buffer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Amit Shah <amit@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: virtualization@lists.linux-foundation.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Reviewed-by: Amit Shah <amit@kernel.org>
Link: https://lore.kernel.org/r/20230922175115.work.059-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-4-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Rework Xilinx hwicap driver probe to use current best practices using
devres APIs, device_get_match_data(), and typed firmware property accessors.
There's no longer any non-DT probing, so CONFIG_OF ifdefs can be dropped.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006214228.337064-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This commit comes at the tail end of a greater effort to remove the
empty elements at the end of the ctl_table arrays (sentinels) which
will reduce the overall build time size of the kernel and run time
memory bloat by ~64 bytes per sentinel (further information Link :
https://lore.kernel.org/all/ZO5Yx5JFogGi%2FcBo@bombadil.infradead.org/)
Remove sentinel from impi_table and random_table
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
This commit comes at the tail end of a greater effort to remove the
empty elements at the end of the ctl_table arrays (sentinels) which
will reduce the overall build time size of the kernel and run time
memory bloat by ~64 bytes per sentinel (further information Link :
https://lore.kernel.org/all/ZO5Yx5JFogGi%2FcBo@bombadil.infradead.org/)
Remove the last empty element from hpet_table.
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
This allows splicing zeroed pages into a pipe, and allows discarding
pages from a pipe by splicing them to /dev/zero. Writing to /dev/zero
should have the same effect as writing to /dev/null, and a
"splice_write" implementation exists only for /dev/null.
(The /dev/zero splice_read implementation could be optimized by
pushing references to the global zero page to the pipe, but that's an
optimization for another day.)
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Link: https://lore.kernel.org/r/20230919073743.1066313-1-max.kellermann@ionos.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hpets.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175348.work.056-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some Amlogic SOC's, mechanism to obtain random number
has been changed. For example, S4 now uses status bit waiting algo.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Implement stm32_rng_suspend()/stm32_rng_resume() low-power APIs
called when the hardware block context will be lost.
There is no need to save the RNG_CR register in
stm32_rng_runtime_suspend() as the context is not lost. Therefore,
only enable/disable the RNG in the runtime sequences.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If "st,rng-lock-conf" DT binding property is set for a stm32-rng node,
the RNG configuration will be locked until next hardware block reset
or platform reset.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For NIST certification the noise source sampling may need to be
restrained.
This change implements an algorithm that gets the rate of the RNG
clock and apply the correct value in CLKDIV field in RNG_CR register
to force the RNG clock rate to be "max_clock_rate" maximum.
As it is platform-specific, implement it as a compat data.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Try to conceal seed errors when possible. If, despite the error
concealing tries, a seed error is still present, then return an error.
A clock error does not compromise the hardware block and data can
still be read from RNG_DR. Just warn that the RNG clock is too slow
and clear RNG_SR.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The RNG driver should be capable of recovering from an error. Implement
an error concealment API. This avoids irrecoverable RNG state.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The RNG present on STM32MP13x platforms introduces a customizable
configuration and the conditional reset.
STM32 RNG configuration should best fit the requirements of the
platform. Therefore, put a platform-specific RNG configuration
field in the platform data. Default RNG configuration for STM32MP13
is the NIST certified configuration [1].
While there, fix and the RNG init sequence to support all RNG
versions.
[1] https://csrc.nist.gov/projects/cryptographic-module-validation-program/entropy-validations/certificate/53
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use devm_platform_get_and_ioremap_resource() to get and ioremap a
resource.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Set a more reasonable timeout for calculating the initial seed.
The reference manuals says that "The initial seed takes approximately
2,000,000 clock cycles." The rngc peripheral clock runs at >= 33.25MHz,
so seeding takes at most 60ms.
A timeout of 200ms is more appropriate than the current value of 3
seconds.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Set a more reasonable timeout for the rngc selftest.
According to the reference manual, "The self test takes approximately
29,000 cycles to complete." The lowest possible frequency of the rngc
peripheral clock is 33.25MHz, the selftest would then take about 872us.
2.5ms should be enough for the selftest timeout.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Fixes: 9f6ec8dc574e ("hwrng: geode - Fix PCI device refcount leak")
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217882
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use unsigned long instead of u64 to silence compile warnings on
32-bit platforms. Also remove the __force bit which seems no
longer needed with a current sparse.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The last RCU stall fix caused a massive throughput regression of the
hwrng on Raspberry Pi 0 - 3. hwrng_msleep doesn't sleep precisely enough
and usleep_range doesn't allow scheduling. So try to restore the
best possible throughput by introducing hwrng_yield which interruptable
sleeps for one jiffy.
Some performance measurements on Raspberry Pi 3B+ (arm64/defconfig):
sudo dd if=/dev/hwrng of=/dev/null count=1 bs=10000
cpu_relax ~138025 Bytes / sec
hwrng_msleep(1000) ~13 Bytes / sec
hwrng_yield ~2510 Bytes / sec
Fixes: 96cb9d055445 ("hwrng: bcm2835 - use hwrng_msleep() instead of cpu_relax()")
Link: https://lore.kernel.org/linux-arm-kernel/bc97ece5-44a3-4c4e-77da-2db3eb66b128@gmx.net/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add a MODULE_DESCRIPTION to fix the W=1 warning
WARNING: modpost: missing MODULE_DESCRIPTION() in
drivers/char/hw_random/st-rng.o
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add a MODULE_DESCRIPTION to fix the W=1 warning
WARNING: modpost: missing MODULE_DESCRIPTION() in
drivers/char/hw_random/nomadik-rng.o
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace dev_err + return with dev_err_probe.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
dev in struct ks_sa_rng is not used. Remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This driver uses a struct ks_sa_rng for its private data. It contains a
struct hwrng. Call container_of to get from hwrng to ks_sa_rng.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fix from Jarkko Sakkinen.
* tag 'tpmdd-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Fix typo in tpmrm class definition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix reference to exported symbols for parisc64 [Masahiro Yamada]
- Block-TLB (BTLB) support on 32-bit CPUs
- sparse and build-warning fixes
* tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
linux/export: fix reference to exported functions for parisc64
parisc: BTLB: Initialize BTLB tables at CPU startup
parisc: firmware: Simplify calling non-PA20 functions
parisc: BTLB: _edata symbol has to be page aligned for BTLB support
parisc: BTLB: Add BTLB insert and purge firmware function wrappers
parisc: BTLB: Clear possibly existing BTLB entries
parisc: Prepare for Block-TLB support on 32-bit kernel
parisc: shmparam.h: Document aliasing requirements of PA-RISC
parisc: irq: Make irq_stack_union static to avoid sparse warning
parisc: drivers: Fix sparse warning
parisc: iosapic.c: Fix sparse warnings
parisc: ccio-dma: Fix sparse warnings
parisc: sba-iommu: Fix sparse warnigs
parisc: sba: Fix compile warning wrt list of SBA devices
parisc: sba_iommu: Fix build warning if procfs if disabled
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
In this case, strncpy is being used specifically for its NUL-padding
behavior (and has been commented as such). Moreover, the destination
string is not required to be NUL-terminated [2].
We can use a more robust and less ambiguous interface in
`memcpy_and_pad` which makes the code more readable and even eliminates
the need for that comment.
Let's also use `strnlen` instead of `strlen()` with an upper-bounds
check as this is intrinsically a part of `strnlen`.
Also included in this patch is a simple 1:1 change of `strncpy` to
`strscpy` for ipmi_ssif.c. If NUL-padding is wanted here as well then we
should opt again for `strscpy_pad`.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://lore.kernel.org/all/ZQEADYBl0uZ1nX60@mail.minyard.net/ [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Message-Id: <20230913-strncpy-drivers-char-ipmi-ipmi-v2-1-e3bc0f6e599f@google.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
|
|
Commit d2e8071bed0be ("tpm: make all 'class' structures const")
unfortunately had a typo for the name on tpmrm.
Fixes: d2e8071bed0b ("tpm: make all 'class' structures const")
Signed-off-by: Justin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.
None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.
While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.
There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.
So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.
[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/0075883c-7c51-00f5-2c2d-5119c1820410@web.de/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/87bkiilpc4.fsf@mid.deneb.enyo.de/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The vendor check introduced by commit 554b841d4703 ("tpm: Disable RNG for
all AMD fTPMs") doesn't work properly on a number of Intel fTPMs. On the
reported systems the TPM doesn't reply at bootup and returns back the
command code. This makes the TPM fail probe on Lenovo Legion Y540 laptop.
Since only Microsoft Pluton is the only known combination of AMD CPU and
fTPM from other vendor, disable hwrng otherwise. In order to make sysadmin
aware of this, print also info message to the klog.
Cc: stable@vger.kernel.org
Fixes: 554b841d4703 ("tpm: Disable RNG for all AMD fTPMs")
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217804
Reported-by: Patrick Steinhardt <ps@pks.im>
Reported-by: Raymond Jay Golo <rjgolo@gmail.com>
Reported-by: Ronan Pigott <ronan@rjp.ie>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Some error paths don't call acpi_put_table() before returning.
Branch to the correct place instead of doing some direct return.
Fixes: 4d2732882703 ("tpm_crb: Add support for CRB devices based on Pluton")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Matthew Garrett <mgarrett@aurora.tech>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core updates and additions for 6.6-rc1.
Included in here are:
- stable kernel documentation updates
- class structure const work from Ivan on various subsystems
- kernfs tweaks
- driver core tests!
- kobject sanity cleanups
- kobject structure reordering to save space
- driver core error code handling fixups
- other minor driver core cleanups
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
driver core: Call in reversed order in device_platform_notify_remove()
driver core: Return proper error code when dev_set_name() fails
kobject: Remove redundant checks for whether ktype is NULL
kobject: Add sanity check for kset->kobj.ktype in kset_register()
drivers: base: test: Add missing MODULE_* macros to root device tests
drivers: base: test: Add missing MODULE_* macros for platform devices tests
drivers: base: Free devm resources when unregistering a device
drivers: base: Add basic devm tests for platform devices
drivers: base: Add basic devm tests for root devices
kernfs: fix missing kernfs_iattr_rwsem locking
docs: stable-kernel-rules: mention that regressions must be prevented
docs: stable-kernel-rules: fine-tune various details
docs: stable-kernel-rules: make the examples for option 1 a proper list
docs: stable-kernel-rules: move text around to improve flow
docs: stable-kernel-rules: improve structure by changing headlines
base/node: Remove duplicated include
kernfs: attach uuid for every kernfs and report it in fsid
kernfs: add stub helper for kernfs_generic_poll()
x86/resctrl: make pseudo_lock_class a static const structure
x86/MSR: make msr_class a static const structure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
|
|
Fix this makecheck warning:
drivers/parisc/sba_iommu.c:98:19: warning: symbol 'sba_list'
was not declared. Should it be static?
Signed-off-by: Helge Deller <deller@gmx.de>
|
