| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 0a355aeb24081e4538d4d424cd189f16c0bbd983 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 914a7b3563b8fb92f976619bbd0fa3a4a708baae ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 314139f9f0abdba61ed9a8463bbcb0bf900ac5a2 ]
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0db9254d6b896b587759e2c844c277fb1a6da5b9 ]
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd217f2300793a106b49c7dfcbfb26e348bc7593 ]
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ]
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ]
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ]
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1413ef638abae4ab5621901cf4d8ef08a4a48ba6 upstream.
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7fda ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7fda to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5136ed4fcb05cd4981cc6034a11e66370ed84789 upstream.
There is no code protecting i2c_dev to be freed after it is returned
from i2c_dev_get_by_minor() and using it to access the value which we
already have (minor) isn't safe really.
Avoid using it and get the adapter directly from 'minor'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e6be18f6d62c1d3b331ae020b76a29c2ccf6b0bf upstream.
The call to put_i2c_dev() frees "i2c_dev" so there is a use after
free when we call cdev_del(&i2c_dev->cdev).
Fixes: d6760b14d4a1 ('i2c: dev: switch from register_chrdev to cdev API')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 72a71f869c95dc11b73f09fe18c593d4a0618c3f upstream.
I stumbled multiple times over 'return_i2c_dev', especially before the
actual 'return res'. It makes the code hard to read, so reanme the
function to 'put_i2c_dev' which also better matches 'get_free_i2c_dev'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d6760b14d4a1243f918d983bba1e35c5a5cd5a6d upstream.
i2c-dev had never moved away from the older register_chrdev interface to
implement its char device registration. The register_chrdev API has the
limitation of enabling only up to 256 i2c-dev busses to exist.
Large platforms with lots of i2c devices (i.e. pluggable transceivers)
with dedicated busses may have to exceed that limit.
In particular, there are also platforms making use of the i2c bus
multiplexing API, which instantiates a virtual bus for each possible
multiplexed selection.
This patch removes the register_chrdev usage and replaces it with the
less old cdev API, which takes away the 256 i2c-dev bus limitation.
It should not have any other impact for i2c bus drivers or user space.
This patch has been tested on qemu x86 and qemu powerpc platforms with
the aid of a module which adds and removes 5000 virtual i2c busses, as
well as validated on an existing powerpc hardware platform which makes
use of the i2c bus multiplexing API.
i2c-dev busses with device minor numbers larger than 256 have also been
validated to work with the existing i2c-tools.
Signed-off-by: Erico Nunes <erico.nunes@datacom.ind.br>
[wsa: kept includes sorted]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 08c6e8cc66282a082484480c1a5641bc27d26c55 upstream.
This is effectively reapplies the commit b0898fdaffb2 ("i2c: designware-pci: use
IRQF_COND_SUSPEND flag") after the commit d80d134182ba ("i2c: designware: Move
common probe code into i2c_dw_probe()"). Original message as follows.
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Fixes: d80d134182ba (i2c: designware: Move common probe code into i2c_dw_probe())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f491c6687332920e296d0209e366fe2ca7eab1c6 ]
Fix a missing struct parameter description to allow
warning free W=1 compilation.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e1b9f99ff8c40bba6e59de9ad4a659447b1e4112 upstream.
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e661cedcc0a072d91a32cb88e0515ea26e35711 upstream.
The printout for txabrt is way too talkative and is highly annoying with
scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest
can be gained by I2C core debugging and datasheet information. Also,
make it a debug printout, it won't help the regular user.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fece4978510e43f09c8cd386fee15210e8c68493 ]
Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a71e2ac1f32097fbb2beab098687a7a95c84543e upstream.
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes: 310c18a41450 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0692f0eef91354b62c2b4c94954536536be5425 ]
If I2C_M_RECV_LEN check failed, msgs[i].buf allocated by memdup_user
will not be freed. Pump index up so it will be freed.
Fixes: 838bfa6049fb ("i2c-dev: Add support for I2C_M_RECV_LEN")
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ca21f851cc9643af049226d57fabc3c883ea648e upstream.
The Acorn i2c driver (for RiscPC) triggers the "i2c adapter has no name"
warning in the I2C core driver, resulting in the RTC being inaccessible.
Fix this.
Fixes: 2236baa75f70 ("i2c: Sanity checks on adapter registration")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89c6efa61f5709327ecfa24bff18e57a4e80c7fa upstream.
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.
It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.
This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.
Call Trace:
[<ffffffff8139f695>] dump_stack+0x67/0x92
[<ffffffff811802a4>] panic+0xc5/0x1eb
[<ffffffff810ecb5f>] ? vprintk_default+0x1f/0x30
[<ffffffff817456d3>] ? i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff8109a68b>] __stack_chk_fail+0x1b/0x20
[<ffffffff817456d3>] i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff81745aed>] i2cdev_ioctl+0x4d/0x1e0
[<ffffffff811f761a>] do_vfs_ioctl+0x2ba/0x490
[<ffffffff81336e43>] ? security_file_ioctl+0x43/0x60
[<ffffffff811f7869>] SyS_ioctl+0x79/0x90
[<ffffffff81a22e97>] entry_SYSCALL_64_fastpath+0x12/0x6a
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
[connoro@google.com: 4.9 backport: adjust filename]
Signed-off-by: Connor O'Brien <connoro@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4e3f4ae1d9c9330de355f432b69952e8cef650c upstream.
Tegra186 and prior supports maximum 4K bytes per packet transfer
including 12 bytes of packet header.
This patch fixes max write length limit to account packet header
size for transfers.
Cc: stable@vger.kernel.org # 4.4+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d358def706880defa4c9e87381c5bf086a97d5f9 ]
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f5c85fe3a60ace555d09898166af372547f97fc ]
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6ebec961d59bccf65d08b13fc1ad4e6272a89338 upstream.
If adapter->retries is set to a minus value from user space via ioctl,
it will make __i2c_transfer and __i2c_smbus_xfer skip the calling to
adapter->algo->master_xfer and adapter->algo->smbus_xfer that is
registered by the underlying bus drivers, and return value 0 to all the
callers. The bus driver will never be accessed anymore by all users,
besides, the users may still get successful return value without any
error or information log print out.
If adapter->timeout is set to minus value from user space via ioctl,
it will make the retrying loop in __i2c_transfer and __i2c_smbus_xfer
always break after the the first try, due to the time_after always
returns true.
Signed-off-by: Yi Zeng <yizeng@asrmicro.com>
[wsa: minor grammar updates to commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0544ee4b1ad574aec3b6379af5f5cdee42840971 ]
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c7f25cae54b840302e4f1b371dbf318fbf09ab2 ]
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 08d9db00fe0e300d6df976e6c294f974988226dd upstream.
The i2c-scmi driver crashes when the SMBus Write Block transaction is
executed:
WARNING: CPU: 9 PID: 2194 at mm/page_alloc.c:3931 __alloc_pages_slowpath+0x9db/0xec0
Call Trace:
? get_page_from_freelist+0x49d/0x11f0
? alloc_pages_current+0x6a/0xe0
? new_slab+0x499/0x690
__alloc_pages_nodemask+0x265/0x280
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x18/0x40
kmalloc_order_trace+0x24/0xb0
? acpi_ut_allocate_object_desc_dbg+0x62/0x10c
__kmalloc+0x203/0x220
acpi_os_allocate_zeroed+0x34/0x36
acpi_ut_copy_eobject_to_iobject+0x266/0x31e
acpi_evaluate_object+0x166/0x3b2
acpi_smbus_cmi_access+0x144/0x530 [i2c_scmi]
i2c_smbus_xfer+0xda/0x370
i2cdev_ioctl_smbus+0x1bd/0x270
i2cdev_ioctl+0xaa/0x250
do_vfs_ioctl+0xa4/0x600
SyS_ioctl+0x79/0x90
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
ACPI Error: Evaluating _SBW: 4 (20170831/smbus_cmi-185)
This problem occurs because the length of ACPI Buffer object is not
defined/initialized in the code before a corresponding ACPI method is
called. The obvious patch below fixes this issue.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Acked-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c85609b08c4761eca0a40fd7beb06bc650f252d ]
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 38f5d8d8cbb2ffa2b54315118185332329ec891c ]
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: dd6fd4a32793 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7fd6d98b89f382d414e1db528e29a67bbd749457 ]
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 851a15114895c5bce163a6f2d57e0aa4658a1be4 upstream.
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes: 84d7f2ebd70d ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae7304c3ea28a3ba47a7a8312c76c654ef24967e upstream.
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cc8de9a68599b261244ea453b38678229f06ada7 ]
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value
and stretch the clock in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bed4ff1ed4d8f2ef5007c5c6ae1b29c5677a3632 upstream.
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17e83549e199d89aace7788a9f11c108671eecf5 upstream.
Fix the following kernel bug:
kernel BUG at drivers/iommu/intel-iommu.c:3260!
invalid opcode: 0000 [#5] PREEMPT SMP
Hardware name: Intel Corp. Harcuvar/Server, BIOS HAVLCRB0.X64.0013.D39.1608311820 08/31/2016
task: ffff880175389950 ti: ffff880176bec000 task.ti: ffff880176bec000
RIP: 0010:[<ffffffff8150a83b>] [<ffffffff8150a83b>] intel_unmap+0x25b/0x260
RSP: 0018:ffff880176bef5e8 EFLAGS: 00010296
RAX: 0000000000000024 RBX: ffff8800773c7c88 RCX: 000000000000ce04
RDX: 0000000080000000 RSI: 0000000000000000 RDI: 0000000000000009
RBP: ffff880176bef638 R08: 0000000000000010 R09: 0000000000000004
R10: ffff880175389c78 R11: 0000000000000a4f R12: ffff8800773c7868
R13: 00000000ffffac88 R14: ffff8800773c7818 R15: 0000000000000001
FS: 00007fef21258700(0000) GS:ffff88017b5c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000066d6d8 CR3: 000000007118c000 CR4: 00000000003406e0
Stack:
00000000ffffac88 ffffffff8199867f ffff880176bef5f8 ffff880100000030
ffff880176bef668 ffff8800773c7c88 ffff880178288098 ffff8800772c0010
ffff8800773c7818 0000000000000001 ffff880176bef648 ffffffff8150a86e
Call Trace:
[<ffffffff8199867f>] ? printk+0x46/0x48
[<ffffffff8150a86e>] intel_unmap_page+0xe/0x10
[<ffffffffa039d99b>] ismt_access+0x27b/0x8fa [i2c_ismt]
[<ffffffff81554420>] ? __pm_runtime_suspend+0xa0/0xa0
[<ffffffff815544a0>] ? pm_suspend_timer_fn+0x80/0x80
[<ffffffff81554420>] ? __pm_runtime_suspend+0xa0/0xa0
[<ffffffff815544a0>] ? pm_suspend_timer_fn+0x80/0x80
[<ffffffff8143dfd0>] ? pci_bus_read_dev_vendor_id+0xf0/0xf0
[<ffffffff8172b36c>] i2c_smbus_xfer+0xec/0x4b0
[<ffffffff810aa4d5>] ? vprintk_emit+0x345/0x530
[<ffffffffa038936b>] i2cdev_ioctl_smbus+0x12b/0x240 [i2c_dev]
[<ffffffff810aa829>] ? vprintk_default+0x29/0x40
[<ffffffffa0389b33>] i2cdev_ioctl+0x63/0x1ec [i2c_dev]
[<ffffffff811b04c8>] do_vfs_ioctl+0x328/0x5d0
[<ffffffff8119d8ec>] ? vfs_write+0x11c/0x190
[<ffffffff8109d449>] ? rt_up_read+0x19/0x20
[<ffffffff811b07f1>] SyS_ioctl+0x81/0xa0
[<ffffffff819a351b>] system_call_fastpath+0x16/0x6e
This happen When run "i2cdetect -y 0" detect SMBus iSMT adapter.
After finished I2C block read/write, when unmap the data buffer,
a wrong device address was pass to dma_unmap_single().
To fix this, give dma_unmap_single() the "dev" parameter, just like
what dma_map_single() does, then unmap can find the right devices.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Liwei Song <liwei.song@windriver.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f9e3e0d4dd3338b3f3dde080789f71901e1e4ff upstream.
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840ff7 ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae481cc139658e89eb3ea671dd00b67bd87f01a3 upstream.
Resume failed because of uninitialized registers. Instead of adding a
resume callback, we simply initialize registers before every transfer.
This lightweight change is more robust and will keep us safe if we ever
need support for power domains or dynamic frequency changes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52df445f29b79006d8b2dcd129152987c0d3bd64 upstream.
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3be0af15959e11fa535d5332ab3d7cf34abd09b upstream.
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d89667b14f9d13b684287f6189ca209af5feee43 upstream.
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc21d0b4b62e41e5013d763adade5ea4462c33a4 upstream.
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9d0684c79c4b9d30ce0d47d3270493dd0e76e59 upstream.
We want to reuse this function later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff2316b87a336bff940939cd9fc56287ed48e578 upstream.
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90f779e565bdc18dd4f79d81cf11f43a7266010b upstream.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c78cdc1c06308a59d6ed4145cdba73fdeff8c0d upstream.
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e43e0df13f8528ca55ed79f469c4b2af897fa796 upstream.
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31184d8c6ea49ea0676d100cdd7e1f102ad025b5 ]
The errata FE-8471889 description has been updated. There is still a
timing violation for repeated start. But the errata now states that it
was only the case for the Standard mode (100 kHz), in Fast mode (400 kHz)
there is no issue.
This patch limit the errata fix to the Standard mode.
It has been tesed successfully on the clearfog (Aramda 388 based board).
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
