summaryrefslogtreecommitdiff
path: root/drivers/ide
AgeCommit message (Collapse)Author
2015-05-11Merge branch 'for-4.1-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "Rather big for fixes pull. - SCC controllers never lived to see the light of the day. Both libata and ide drivers removed. - In some configurations, link power management policy changes sometimes cause delayed spurious PHY events which can develop into noticeable failures. This has been reported several times over the years. Gabriele's patches suppress PHY events for a while after LPM policy changes which should help most of these failures without causing too much problem for hotplug use cases. - A few controller specific fixes" [ Hmm. I don't think removing SSC support is really a "fix", but hey, it removes a lot of lines of code. Which I like. So ... good riddance ] * 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: ahci: avoton port-disable reset-quirk ata: select DW_DMAC in case of SATA_DWC libata: Blacklist queued TRIM on all Samsung 800-series libata: Ignore spurious PHY event on LPM policy change libata: Add helper to determine when PHY events should be ignored ata: ahci_st: fixup layering violations / drvdata errors Remove celleb-only SCC PATA drivers
2015-04-17ide: remove deprecated use of pci apiQuentin Lambert
Replace occurences of the pci api by appropriate call to the dma api. A simplified version of the semantic patch that finds this problem is as follows: (http://coccinelle.lip6.fr) @deprecated@ idexpression id; position p; @@ ( pci_dma_supported@p ( id, ...) | pci_alloc_consistent@p ( id, ...) ) @bad1@ idexpression id; position deprecated.p; @@ ...when != &id->dev when != pci_get_drvdata ( id ) when != pci_enable_device ( id ) ( pci_dma_supported@p ( id, ...) | pci_alloc_consistent@p ( id, ...) ) @depends on !bad1@ idexpression id; expression direction; position deprecated.p; @@ ( - pci_dma_supported@p ( id, + dma_supported ( &id->dev, ... + , GFP_ATOMIC ) | - pci_alloc_consistent@p ( id, + dma_alloc_coherent ( &id->dev, ... + , GFP_ATOMIC ) ) Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-16Merge tag 'powerpc-4.1-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux Pull powerpc updates from Michael Ellerman: - Numerous minor fixes, cleanups etc. - More EEH work from Gavin to remove its dependency on device_nodes. - Memory hotplug implemented entirely in the kernel from Nathan Fontenot. - Removal of redundant CONFIG_PPC_OF by Kevin Hao. - Rewrite of VPHN parsing logic & tests from Greg Kurz. - A fix from Nish Aravamudan to reduce memory usage by clamping nodes_possible_map. - Support for pstore on powernv from Hari Bathini. - Removal of old powerpc specific byte swap routines by David Gibson. - Fix from Vasant Hegde to prevent the flash driver telling you it was flashing your firmware when it wasn't. - Patch from Ben Herrenschmidt to add an OPAL heartbeat driver. - Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek. - Some fixes for migration from Tyrel Datwyler. - A new syscall to switch the cpu endian by Michael Ellerman. - Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn. - A fix for the OPAL sensor driver from Cédric Le Goater. - Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman. - Large series from Daniel Axtens to make our PCI hooks per PHB rather than per machine. - Small patch from Sam Bobroff to explicitly abort non-suspended transactions on syscalls, plus a test to exercise it. - Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu. - Small patch to enable the hard lockup detector from Anton Blanchard. - Fix from Dave Olson for missing L2 cache information on some CPUs. - Some fixes from Michael Ellerman to get Cell machines booting again. - Freescale updates from Scott: Highlights include BMan device tree nodes, an MSI erratum workaround, a couple minor performance improvements, config updates, and misc fixes/cleanup. * tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits) powerpc/powermac: Fix build error seen with powermac smp builds powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE powerpc: Remove PPC32 code from pseries specific find_and_init_phbs() powerpc/cell: Fix iommu breakage caused by controller_ops change powerpc/eeh: Fix crash in eeh_add_device_early() on Cell powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails powerpc/pseries: Correct memory hotplug locking powerpc: Fix missing L2 cache size in /sys/devices/system/cpu powerpc: Add ppc64 hard lockup detector support oprofile: Disable oprofile NMI timer on ppc64 powerpc/perf/hv-24x7: Add missing put_cpu_var() powerpc/perf/hv-24x7: Break up single_24x7_request powerpc/perf/hv-24x7: Define update_event_count() powerpc/perf/hv-24x7: Whitespace cleanup powerpc/perf/hv-24x7: Define add_event_to_24x7_request() powerpc/perf/hv-24x7: Rename hv_24x7_event_update powerpc/perf/hv-24x7: Move debug prints to separate function powerpc/perf/hv-24x7: Drop event_24x7_request() powerpc/perf/hv-24x7: Use pr_devel() to log message ... Conflicts: tools/testing/selftests/powerpc/Makefile tools/testing/selftests/powerpc/tm/Makefile
2015-04-14Merge tag 'pm+acpi-4.1-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI updates from Rafael Wysocki: "These are mostly fixes and cleanups all over, although there are a few items that sort of fall into the new feature category. First off, we have new callbacks for PM domains that should help us to handle some issues related to device initialization in a better way. There also is some consolidation in the unified device properties API area allowing us to use that inferface for accessing data coming from platform initialization code in addition to firmware-provided data. We have some new device/CPU IDs in a few drivers, support for new chips and a new cpufreq driver too. Specifics: - Generic PM domains support update including new PM domain callbacks to handle device initialization better (Russell King, Rafael J Wysocki, Kevin Hilman) - Unified device properties API update including a new mechanism for accessing data provided by platform initialization code (Rafael J Wysocki, Adrian Hunter) - ARM cpuidle update including ARM32/ARM64 handling consolidation (Daniel Lezcano) - intel_idle update including support for the Silvermont Core in the Baytrail SOC and for the Airmont Core in the Cherrytrail and Braswell SOCs (Len Brown, Mathias Krause) - New cpufreq driver for Hisilicon ACPU (Leo Yan) - intel_pstate update including support for the Knights Landing chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi) - QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann) - powernv cpufreq driver update (Shilpasri G Bhat) - devfreq update including Tegra support changes (Tomeu Vizoso, MyungJoo Ham, Chanwoo Choi) - powercap RAPL (Running-Average Power Limit) driver update including support for Intel Broadwell server chips (Jacob Pan, Mathias Krause) - ACPI device enumeration update related to the handling of the special PRP0001 device ID allowing DT-style 'compatible' property to be used for ACPI device identification (Rafael J Wysocki) - ACPI EC driver update including limited _DEP support (Lan Tianyu, Lv Zheng) - ACPI backlight driver update including a new mechanism to allow native backlight handling to be forced on non-Windows 8 systems and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede) - New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu) - Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger, Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki) - Fixes related to suspend-to-idle for the iTCO watchdog driver and the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu) - PM tracing support for the suspend phase of system suspend/resume transitions (Zhonghui Fu) - Configurable delay for the system suspend/resume testing facility (Brian Norris) - PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)" * tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits) ACPI / scan: Fix NULL pointer dereference in acpi_companion_match() ACPI / scan: Rework modalias creation when "compatible" is present intel_idle: mark cpu id array as __initconst powercap / RAPL: mark rapl_ids array as __initconst powercap / RAPL: add ID for Broadwell server intel_pstate: Knights Landing support intel_pstate: remove MSR test cpufreq: fix qoriq uniprocessor build ACPI / scan: Take the PRP0001 position in the list of IDs into account ACPI / scan: Simplify acpi_match_device() ACPI / scan: Generalize of_compatible matching device property: Introduce firmware node type for platform data device property: Make it possible to use secondary firmware nodes PM / watchdog: iTCO: stop watchdog during system suspend cpufreq: hisilicon: add acpu driver ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler cpufreq: powernv: Report cpu frequency throttling intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs intel_idle: Update support for Silvermont Core in Baytrail SOC PM / devfreq: tegra: Register governor on module init ...
2015-04-14Remove celleb-only SCC PATA driversDaniel Axtens
The SCC PATA interface is only used by celleb. celleb has been dropped [1], so drop the drivers. [1] http://patchwork.ozlabs.org/patch/451730/ CC: "David S. Miller" <davem@davemloft.net> CC: linux-ide@vger.kernel.org CC: Valentin Rothberg <valentinrothberg@gmail.com> CC: mpe@ellerman.id.au CC: linuxppc-dev@lists.ozlab.org Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Tejun Heo <tj@kernel.org>
2015-04-13Merge branch 'for-4.1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata updates from Tejun Heo: - Hannes's patchset implements support for better error reporting introduced by the new ATA command spec. - the deperecated pci_ dma API usages have been replaced by dma_ ones. - a bunch of hardware specific updates and some cleanups. * 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: ata: remove deprecated use of pci api ahci: st: st_configure_oob must be called after IP is clocked. ahci: st: Update the ahci_st DT documentation ahci: st: Update the DT example for how to obtain the PHY. sata_dwc_460ex: indent an if statement libata: Add tracepoints libata-eh: Set 'information' field for autosense libata: Implement support for sense data reporting libata: Implement NCQ autosense libata: use status bit definitions in ata_dump_status() ide,ata: Rename ATA_IDX to ATA_SENSE libata: whitespace fixes in ata_to_sense_error() libata: whitespace cleanup in ata_get_cmd_descript() libata: use READ_LOG_DMA_EXT libata: remove ATA_FLAG_LOWTAG sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev sata_dwc_460ex: move to generic DMA driver sata_dwc_460ex: join messages back sata: xgene: add ACPI support for APM X-Gene SATA ports ata: sata_mv: add proper definitions for LP_PHY_CTL register values
2015-04-13Merge branch 'pnp'Rafael J. Wysocki
* pnp: PNP: Avoid leaving unregistered device objects in lists PNP: Convert pnp_lock into a mutex PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver PNP: net/sb1000: Use module_pnp_driver to register driver PNP: media/rc: Use module_pnp_driver to register driver PNP: ide/ide-pnp: Use module_pnp_driver to register driver PNP: ata/pata_isapnp: Use module_pnp_driver to register driver PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver PNP: Add helper macro for pnp_register_driver boilerplate PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
2015-03-27ide,ata: Rename ATA_IDX to ATA_SENSEHannes Reinecke
ATA-8 defines bit 1 as 'ATA_SENSE', not 'ATA_IDX'. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Tejun Heo <tj@kernel.org>
2015-03-23powerpc: Move Power Macintosh drivers to generic byteswappersDavid Gibson
ppc has special instruction forms to efficiently load and store values in non-native endianness. These can be accessed via the arch-specific {ld,st}_le{16,32}() inlines in arch/powerpc/include/asm/swab.h. However, gcc is perfectly capable of generating the byte-reversing load/store instructions when using the normal, generic cpu_to_le*() and le*_to_cpu() functions eaning the arch-specific functions don't have much point. Worse the "le" in the names of the arch specific functions is now misleading, because they always generate byte-reversing forms, but some ppc machines can now run a little-endian kernel. To start getting rid of the arch-specific forms, this patch removes them from all the old Power Macintosh drivers, replacing them with the generic byteswappers. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2015-03-18ide_tape: convert jiffies with jiffies_to_msecsNicholas Mc Guire
Use jiffies_to_msecs for converting jiffies as it handles all of the corner cases reliably and also helps readability. The printk format is fixed up as jiffies_to_msecs returns unsigned int not unsigned long. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-18PNP: ide/ide-pnp: Use module_pnp_driver to register driverPeter Huewe
Removing some boilerplate by using module_pnp_driver instead of calling register and unregister in the otherwise empty init/exit functions Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-12-14Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
2014-12-12drivers: ide: Fix mostly harmless off-by-one hardcoded valueRasmus Villemoes
The string "IOMEGA Clik!" has length 12, not 11. Using strstarts avoids the error-prone hardcoding of the prefix length. For consistency, also change the occurence just above. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-12IDE: Deletion of an unnecessary check before the function call "module_put"Markus Elfring
The module_put() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-20ide: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-18Merge branch 'for-3.18/drivers' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block layer driver update from Jens Axboe: "This is the block driver pull request for 3.18. Not a lot in there this round, and nothing earth shattering. - A round of drbd fixes from the linbit team, and an improvement in asender performance. - Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and hd from Michael Opdenacker. - Disable entropy collection from flash devices by default, from Mike Snitzer. - A small collection of xen blkfront/back fixes from Roger Pau Monné and Vitaly Kuznetsov" * 'for-3.18/drivers' of git://git.kernel.dk/linux-block: block: disable entropy contributions for nonrot devices xen, blkfront: factor out flush-related checks from do_blkif_request() xen-blkback: fix leak on grant map error path xen/blkback: unmap all persistent grants when frontend gets disconnected rsxx: Remove deprecated IRQF_DISABLED block: hd: remove deprecated IRQF_DISABLED drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks drbd: compute the end before rb_insert_augmented() drbd: Add missing newline in resync progress display in /proc/drbd drbd: reduce lock contention in drbd_worker drbd: Improve asender performance drbd: Get rid of the WORK_PENDING macro drbd: Get rid of the __no_warn and __cond_lock macros drbd: Avoid inconsistent locking warning drbd: Remove superfluous newline from "resync_extents" debugfs entry. drbd: Use consistent names for all the bi_end_io callbacks drbd: Use better variable names
2014-10-18Merge branch 'for-3.18/core' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull core block layer changes from Jens Axboe: "This is the core block IO pull request for 3.18. Apart from the new and improved flush machinery for blk-mq, this is all mostly bug fixes and cleanups. - blk-mq timeout updates and fixes from Christoph. - Removal of REQ_END, also from Christoph. We pass it through the ->queue_rq() hook for blk-mq instead, freeing up one of the request bits. The space was overly tight on 32-bit, so Martin also killed REQ_KERNEL since it's no longer used. - blk integrity updates and fixes from Martin and Gu Zheng. - Update to the flush machinery for blk-mq from Ming Lei. Now we have a per hardware context flush request, which both cleans up the code should scale better for flush intensive workloads on blk-mq. - Improve the error printing, from Rob Elliott. - Backing device improvements and cleanups from Tejun. - Fixup of a misplaced rq_complete() tracepoint from Hannes. - Make blk_get_request() return error pointers, fixing up issues where we NULL deref when a device goes bad or missing. From Joe Lawrence. - Prep work for drastically reducing the memory consumption of dm devices from Junichi Nomura. This allows creating clone bio sets without preallocating a lot of memory. - Fix a blk-mq hang on certain combinations of queue depths and hardware queues from me. - Limit memory consumption for blk-mq devices for crash dump scenarios and drivers that use crazy high depths (certain SCSI shared tag setups). We now just use a single queue and limited depth for that" * 'for-3.18/core' of git://git.kernel.dk/linux-block: (58 commits) block: Remove REQ_KERNEL blk-mq: allocate cpumask on the home node bio-integrity: remove the needless fail handle of bip_slab creating block: include func name in __get_request prints block: make blk_update_request print prefix match ratelimited prefix blk-merge: don't compute bi_phys_segments from bi_vcnt for cloned bio block: fix alignment_offset math that assumes io_min is a power-of-2 blk-mq: Make bt_clear_tag() easier to read blk-mq: fix potential hang if rolling wakeup depth is too high block: add bioset_create_nobvec() block: use bio_clone_fast() in blk_rq_prep_clone() block: misplaced rq_complete tracepoint sd: Honor block layer integrity handling flags block: Replace strnicmp with strncasecmp block: Add T10 Protection Information functions block: Don't merge requests if integrity flags differ block: Integrity checksum flag block: Relocate bio integrity flags block: Add a disk flag to block integrity profile block: Add prefix to block integrity profile flags ...
2014-10-15Drivers: ide: Remove typedef atiixp_ide_timingHimangi Saraogi
The Linux kernel coding style guidelines suggest not using typedefs for structure types. This patch gets rid of the typedef for atiixp_ide_timing. The following Coccinelle semantic patch detects the case: @tn1@ type td; @@ typedef struct { ... } td; @script:python tf@ td << tn1.td; tdres; @@ coccinelle.tdres = td; @@ type tn1.td; identifier tf.tdres; @@ -typedef struct + tdres { ... } -td ; @@ type tn1.td; identifier tf.tdres; @@ -td + struct tdres Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-04block: disable entropy contributions for nonrot devicesMike Snitzer
Clear QUEUE_FLAG_ADD_RANDOM in all block drivers that set QUEUE_FLAG_NONROT. Historically, all block devices have automatically made entropy contributions. But as previously stated in commit e2e1a148 ("block: add sysfs knob for turning off disk entropy contributions"): - On SSD disks, the completion times aren't as random as they are for rotational drives. So it's questionable whether they should contribute to the random pool in the first place. - Calling add_disk_randomness() has a lot of overhead. There are more reliable sources for randomness than non-rotational block devices. From a security perspective it is better to err on the side of caution than to allow entropy contributions from unreliable "random" sources. Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-08-28block,scsi: fixup blk_get_request dead queue scenariosJoe Lawrence
The blk_get_request function may fail in low-memory conditions or during device removal (even if __GFP_WAIT is set). To distinguish between these errors, modify the blk_get_request call stack to return the appropriate ERR_PTR. Verify that all callers check the return status and consider IS_ERR instead of a simple NULL pointer check. For consistency, make a similar change to the blk_mq_alloc_request leg of blk_get_request. It may fail if the queue is dead, or the caller was unwilling to wait. Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd] Acked-by: Boaz Harrosh <bharrosh@panasas.com> [for osd] Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-08-05ide: use module_platform_driver()Christoph Jaeger
Eliminate boilerplate code by using module_platform_driver(). Signed-off-by: Christoph Jaeger <christophjaeger@linux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/ideLinus Torvalds
Pull IDE fixes from David Miller: - fix interrupt registry for some Atari IDE chipsets. - adjust Kconfig dependencies for x86_32 specific chips. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide: ide: Fix SC1200 dependencies ide: Fix CS5520 and CS5530 dependencies m68k/atari - ide: do not register interrupt if host->get_lock is set
2014-04-15block: remove struct request buffer memberJens Axboe
This was used in the olden days, back when onions were proper yellow. Basically it mapped to the current buffer to be transferred. With highmem being added more than a decade ago, most drivers map pages out of a bio, and rq->buffer isn't pointing at anything valid. Convert old style drivers to just use bio_data(). For the discard payload use case, just reference the page in the bio. Signed-off-by: Jens Axboe <axboe@fb.com>
2014-03-17ide: Fix SC1200 dependenciesJean Delvare
The SC1200 is a SoC based on the Geode GX1 32-bit x86 processor, so its drivers are only needed on this architecture, except for build testing purpose. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-17ide: Fix CS5520 and CS5530 dependenciesJean Delvare
As far as I know, the CS5520 and CS5530 chipsets were only used with 32-bit x86 Geode processors, so I think their drivers are only needed on this architecture, except for build testing purpose. While we're here, simplify the dependencies for the CS5535 driver. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-04m68k/atari - ide: do not register interrupt if host->get_lock is setMichael Schmitz
On m68k, host->get_lock is used to both lock and register the interrupt that the IDE host shares with other device drivers. Registering the IDE interrupt handler in ide-probe.c results in duplicating the interrupt registered (once via host->get lock, and also via init_irq()), and may result in IDE accepting interrupts even when another driver has locked the interrupt hardware. This opens the whole locking scheme up to races. host->get_lock is set on m68k only, so other drivers' behaviour is not changed. Signed-off-by: Michael Schmitz <schmitz@debian.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: David S. Miller <davem@davemloft.net> Cc: linux-ide@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-28drivers: ide: Include appropriate header file in ide-pio-blacklist.cRashika Kheria
Include appropriate header file include/linux/ide.h in file ide-pio-blacklist.c because function ide_scan_pio_blacklist() has it's prototype declaration in include/linux/ide.h. This eliminates the following warning in ide-pio-blacklist.c: drivers/ide/ide-pio-blacklist.c:85:5: warning: no previous prototype for ‘ide_scan_pio_blacklist’ [-Wmissing-prototypes] Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-28drivers: ide: Include appropriate header file in ide-cd_verbose.cRashika Kheria
Include appropriate header file ide-cd.h in ide-cd_verbose.c because function ide_cd_log_error() has its prototype declaration in ide-cd.h. Also, include linux/ide.h because it contains certain declarations necessary for including ide-cd.h. This eliminates the following warnings in ide-cd_verbose.c: drivers/ide/ide-cd_verbose.c:251:6: warning: no previous prototype for ‘ide_cd_log_error’ [-Wmissing-prototypes] Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-24Merge tag 'pm+acpi-3.14-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management updates from Rafael Wysocki: "As far as the number of commits goes, the top spot belongs to ACPI this time with cpufreq in the second position and a handful of PM core, PNP and cpuidle updates. They are fixes and cleanups mostly, as usual, with a couple of new features in the mix. The most visible change is probably that we will create struct acpi_device objects (visible in sysfs) for all devices represented in the ACPI tables regardless of their status and there will be a new sysfs attribute under those objects allowing user space to check that status via _STA. Consequently, ACPI device eject or generally hot-removal will not delete those objects, unless the table containing the corresponding namespace nodes is unloaded, which is extremely rare. Also ACPI container hotplug will be handled quite a bit differently and cpufreq will support CPU boost ("turbo") generically and not only in the acpi-cpufreq driver. Specifics: - ACPI core changes to make it create a struct acpi_device object for every device represented in the ACPI tables during all namespace scans regardless of the current status of that device. In accordance with this, ACPI hotplug operations will not delete those objects, unless the underlying ACPI tables go away. - On top of the above, new sysfs attribute for ACPI device objects allowing user space to check device status by triggering the execution of _STA for its ACPI object. From Srinivas Pandruvada. - ACPI core hotplug changes reducing code duplication, integrating the PCI root hotplug with the core and reworking container hotplug. - ACPI core simplifications making it use ACPI_COMPANION() in the code "glueing" ACPI device objects to "physical" devices. - ACPICA update to upstream version 20131218. This adds support for the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug facilities. From Bob Moore, Lv Zheng and Betty Dall. - Init code change to carry out the early ACPI initialization earlier. That should allow us to use ACPI during the timekeeping initialization and possibly to simplify the EFI initialization too. From Chun-Yi Lee. - Clenups of the inclusions of ACPI headers in many places all over from Lv Zheng and Rashika Kheria (work in progress). - New helper for ACPI _DSM execution and rework of the code in drivers that uses _DSM to execute it via the new helper. From Jiang Liu. - New Win8 OSI blacklist entries from Takashi Iwai. - Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria, Tang Chen, Zhang Rui. - intel_pstate driver updates, including proper Baytrail support, from Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra. - Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski. - powernow-k6 cpufreq driver fixes from Mikulas Patocka. - cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown. - Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar. - cpuidle cleanups from Bartlomiej Zolnierkiewicz. - Support for hibernation APM events from Bin Shi. - Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled during thaw transitions from Bjørn Mork. - PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson. - PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa, Rashika Kheria. - New tool for profiling system suspend from Todd E Brandt and a cpupower tool cleanup from One Thousand Gnomes" * tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits) thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412) cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ Documentation: cpufreq / boost: Update BOOST documentation cpufreq: exynos: Extend Exynos cpufreq driver to support boost cpufreq / boost: Kconfig: Support for software-managed BOOST acpi-cpufreq: Adjust the code to use the common boost attribute cpufreq: Add boost frequency support in core intel_pstate: Add trace point to report internal state. cpufreq: introduce cpufreq_generic_get() routine ARM: SA1100: Create dummy clk_get_rate() to avoid build failures cpufreq: stats: create sysfs entries when cpufreq_stats is a module cpufreq: stats: free table and remove sysfs entry in a single routine cpufreq: stats: remove hotplug notifiers cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly cpufreq: speedstep: remove unused speedstep_get_state platform: introduce OF style 'modalias' support for platform bus PM / tools: new tool for suspend/resume performance optimization ACPI: fix module autoloading for ACPI enumerated devices ACPI: add module autoloading support for ACPI enumerated devices ACPI: fix create_modalias() return value handling ...
2013-12-07ACPI / bind: Move acpi_get_child() to drivers/ide/ide-acpi.cRafael J. Wysocki
Since drivers/ide/ide-acpi.c is the only remaining user of acpi_get_child(), move that function into that file as a static routine. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-12-07ACPI: Clean up inclusions of ACPI header filesLv Zheng
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h> inclusions and remove some inclusions of those files that aren't necessary. First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h> should not be included directly from any files that are built for CONFIG_ACPI unset, because that generally leads to build warnings about undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set, <linux/acpi.h> includes those files and for CONFIG_ACPI unset it provides stub ACPI symbols to be used in that case. Second, there are ordering dependencies between those files that always have to be met. Namely, it is required that <acpi/acpi_bus.h> be included prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the latter depends on are always there. And <acpi/acpi.h> which provides basic ACPICA type declarations should always be included prior to any other ACPI headers in CONFIG_ACPI builds. That also is taken care of including <linux/acpi.h> as appropriate. Signed-off-by: Lv Zheng <lv.zheng@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Tony Luck <tony.luck@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff) Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-11-26zorro: ZTWO_VADDR() should return "void __iomem *"Geert Uytterhoeven
ZTWO_VADDR() converts from physical to virtual I/O addresses, so it should return "void __iomem *" instead of "unsigned long". This allows to drop several casts, but requires adding a few casts to accomodate legacy driver frameworks that store "unsigned long" I/O addresses. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-11-20Merge tag 'pm+acpi-2-3.13-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI and power management updates from Rafael Wysocki: - ACPI-based device hotplug fixes for issues introduced recently and a fix for an older error code path bug in the ACPI PCI host bridge driver - Fix for recently broken OMAP cpufreq build from Viresh Kumar - Fix for a recent hibernation regression related to s2disk - Fix for a locking-related regression in the ACPI EC driver from Puneet Kumar - System suspend error code path fix related to runtime PM and runtime PM documentation update from Ulf Hansson - cpufreq's conservative governor fix from Xiaoguang Chen - New processor IDs for intel_idle and turbostat and removal of an obsolete Kconfig option from Len Brown - New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg - Removal of several ACPI video DMI blacklist entries that are not necessary any more from Aaron Lu - Rework of the ACPI companion representation in struct device and code cleanup related to that change from Rafael J Wysocki, Lan Tianyu and Jarkko Nikula - Fixes for assigning names to ACPI-enumerated I2C and SPI devices from Jarkko Nikula * tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits) PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed() ACPI / PCI root: Clear driver_data before failing enumeration ACPI / hotplug: Fix PCI host bridge hot removal ACPI / hotplug: Fix acpi_bus_get_device() return value check cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs() ACPI / video: clean up DMI table for initial black screen problem ACPI / EC: Ensure lock is acquired before accessing ec struct members PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps() ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac spi: Use stable dev_name for ACPI enumerated SPI slaves i2c: Use stable dev_name for ACPI enumerated I2C slaves ACPI: Provide acpi_dev_name accessor for struct acpi_device device name ACPI / bind: Use (put|get)_device() on ACPI device objects too ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node cpufreq: OMAP: Fix compilation error 'r & ret undeclared' PM / Runtime: Fix error path for prepare PM / Runtime: Update documentation around probe|remove|suspend cpufreq: conservative: set requested_freq to policy max when it is over policy max ...
2013-11-14ide: pmac: remove unnecessary pci_set_drvdata()Jingoo Han
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-14ide: cs5536: use module_pci_driver()Jingoo Han
Use module_pci_driver() macro which makes the code smaller and simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-14ide: pmac: Remove casting the return value which is a void pointerJingoo Han
Casting the return value which is a void pointer is redundant. The conversion from void pointer to any other pointer type is guaranteed by the C programming language. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-14ACPI: Eliminate the DEVICE_ACPI_HANDLE() macroRafael J. Wysocki
Since DEVICE_ACPI_HANDLE() is now literally identical to ACPI_HANDLE(), replace it with the latter everywhere and drop its definition from include/acpi.h. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-11-14ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_nodeRafael J. Wysocki
Modify struct acpi_dev_node to contain a pointer to struct acpi_device associated with the given device object (that is, its ACPI companion device) instead of an ACPI handle corresponding to it. Introduce two new macros for manipulating that pointer in a CONFIG_ACPI-safe way, ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the ACPI_HANDLE() macro to take the above changes into account. Drop the ACPI_HANDLE_SET() macro entirely and rework its users to use ACPI_COMPANION_SET() instead. For some of them who used to pass the result of acpi_get_child() directly to ACPI_HANDLE_SET() introduce a helper routine acpi_preset_companion() doing an equivalent thing. The main motivation for doing this is that there are things represented by struct acpi_device objects that don't have valid ACPI handles (so called fixed ACPI hardware features, such as power and sleep buttons) and we would like to create platform device objects for them and "glue" them to their ACPI companions in the usual way (which currently is impossible due to the lack of valid ACPI handles). However, there are more reasons why it may be useful. First, struct acpi_device pointers allow of much better type checking than void pointers which are ACPI handles, so it should be more difficult to write buggy code using modified struct acpi_dev_node and the new macros. Second, the change should help to reduce (over time) the number of places in which the result of ACPI_HANDLE() is passed to acpi_bus_get_device() in order to obtain a pointer to the struct acpi_device associated with the given "physical" device, because now that pointer is returned by ACPI_COMPANION() directly. Finally, the change should make it easier to write generic code that will build both for CONFIG_ACPI set and unset without adding explicit compiler directives to it. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
2013-11-12Merge tag 'h8300-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull h8300 platform removal from Guenter Roeck: "The patch series has been in -next for more than one relase cycle. I did get a number of Acks, and no objections. H8/300 has been dead for several years, the kernel for it has not compiled for ages, and recent versions of gcc for it are broken. Remove support for it" * tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: CREDITS: Add Yoshinori Sato for h8300 fs/minix: Drop dependency on H8300 Drop remaining references to H8/300 architecture Drop MAINTAINERS entry for H8/300 watchdog: Drop references to H8300 architecture net/ethernet: Drop H8/300 Ethernet driver net/ethernet: smsc9194: Drop conditional code for H8/300 ide: Drop H8/300 driver Drop support for Renesas H8/300 (h8300) architecture
2013-11-11Merge tag 'cleanup-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "This branch contains code cleanups, moves and removals for 3.13. Qualcomm msm targets had a bunch of code removal for legacy non-DT platforms. Nomadik saw more device tree conversions and cleanup of old code. Tegra has some code refactoring, etc. One longish patch series from Sebastian Hasselbarth changes the init_time hooks and tries to use a generic implementation for most platforms, since they were all doing more or less the same things. Finally the "shark" platform is removed in this release. It's been abandoned for a while and nobody seems to care enough to keep it around. If someone comes along and wants to resurrect it, the removal can easily be reverted and code brought back. Beyond this, mostly a bunch of removals of stale content across the board, etc" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits) ARM: gemini: convert to GENERIC_CLOCKEVENTS ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options ARM: OMAP3: control: add API for setting IVA bootmode ARM: OMAP3: CM/control: move CM scratchpad save to CM driver ARM: OMAP3: McBSP: do not access CM register directly ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock ARM: OMAP2: CM/PM: remove direct register accesses outside CM code MAINTAINERS: Add patterns for DTS files for AT91 ARM: at91: remove init_machine() as default is suitable ARM: at91/dt: split sama5d3 peripheral definitions ARM: at91/dt: split sam9x5 peripheral definitions ARM: Remove temporary sched_clock.h header ARM: clps711x: Use linux/sched_clock.h MAINTAINERS: Add DTS files to patterns for Samsung platform ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order clk: nomadik: fix missing __init on nomadik_src_init ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support ...
2013-10-16ide: convert bus code to use dev_groupsGreg Kroah-Hartman
The dev_attrs field of struct bus_type is going away soon, dev_groups should be used instead. This converts the ide bus code to use the correct field. Acked-by: David S. Miller <davem@davemloft.net> Cc: <linux-ide@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25ide: drop dependency on ARCH_SHARKLinus Walleij
This drops the selection of default IDE chipset for the Shark machine as it has been deleted. Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-09-16ide: Drop H8/300 driverGuenter Roeck
Architecture is gone, so there is no need to keep its ide driver around. Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2013-09-05ide: sgiioc4: Staticize ioc4_ide_attach_one()Jingoo Han
ioc4_ide_attach_one() is used only in this file. Fix the following sparse warnings: drivers/ide/sgiioc4.c:603:5: warning: symbol 'ioc4_ide_attach_one' was not declared. Should it be static? Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-05ide: palm_bk3710: add missing __iomem annotationJingoo Han
Added missing __iomem annotation in order to fix the following sparse warnings: drivers/ide/palm_bk3710.c:194:31: warning: incorrect type in initializer (different address spaces) drivers/ide/palm_bk3710.c:194:31: expected void [noderef] <asn:2>*base drivers/ide/palm_bk3710.c:194:31: got void *<noident> drivers/ide/palm_bk3710.c:212:31: warning: incorrect type in initializer (different address spaces) drivers/ide/palm_bk3710.c:212:31: expected void [noderef] <asn:2>*base drivers/ide/palm_bk3710.c:212:31: got void *<noident> Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-05ide: use dev_get_platdata()Jingoo Han
Use the wrapper function for retrieving the platform data instead of accessing dev->platform_data directly. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-05ide-disk_proc: use macro to replace magic numberXinghai Yu
Signed-off-by: Xinghai Yu <yuxinghai@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-05ide: replace strict_strtol() with kstrtol()Jingoo Han
The usage of strict_strtol() is not preferred, because strict_strtol() is obsolete. Thus, kstrtol() should be used. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-30ACPI / PM: Use ACPI_STATE_D3_COLD instead of ACPI_STATE_D3 everywhereRafael J. Wysocki
There are several places in the tree where ACPI_STATE_D3 is used instead of ACPI_STATE_D3_COLD which should be used instead for clarity. Modify them all to use ACPI_STATE_D3_COLD as appropriate. [The definition of ACPI_STATE_D3 itself cannot go away at this point as it is part of ACPICA.] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com>
2013-07-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/ideLinus Torvalds
Pull IDE updates from David Miller: "Just a few small things: 1) module_platform_driver_probe() conversions from Jingoo Han. 2) module_pci_driver() conversion from Libo Chen. 3) PIO size calculation fix from Steven J Hill" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide: ide: Fix IDE PIO size calculation drivers/ide/delkin_cb: Convert to module_pci_driver ide: gayle: use module_platform_driver_probe() ide: tx4939ide: use module_platform_driver_probe() ide: tx4938ide: use module_platform_driver_probe()