| Age | Commit message (Collapse) | Author |
|---|
|
commit b81d8948746520f989e86d66292ff72b5056114a upstream.
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1dc839ec09d3ab2a4156dc98328b8bc3586f2b70 upstream.
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487ec ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d18e81183b1cb9c309266cbbce9acd3e0c528d04 upstream.
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c1671e0d13d4a0ba4fb3a0da932bf3736d7ff73 ]
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 94391fae82f71c98ecc7716a32611fcca73c74eb ]
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a6d281946c330cee2855f6d0cd796616e54601f ]
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bbfd4506f962e7e6fff8f37f017154a3c3791264 ]
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b16f3299ae1aa3c327e1fb742d0379ae4d6e86f2 ]
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9bb5a495424fd4bfa672eb1f31481248562fa156 upstream.
Currently skb_checksum_help()'s return is ignored, but it may
return error when it fails to allocate memory when linearizing.
So adds checking for the return of skb_checksum_help().
Fixes: 76ad4f0ee747("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 472497d0bdae890a896013332a0b673f9acdf2bf ]
If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da7395 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b416e872be06fdace3c36cf5210130509d0f0e72 ]
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 905416f18fe74bdd4de91bf94ef5a790a36e4b99 ]
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b4047aac4ec1066bab6c71950623746d7bcf7154 ]
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 568a54bdf70b143f3e0befa298e22ad469ffc732 ]
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b0577 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2867298dd49ee84214b8721521dc7a5a6382520c ]
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415dd ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d392ecd1bc29ae15b0e284d5f732c2d36f244271 ]
Limiting the scope of the variable vector_ring_chain to the block where it
is used.
Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed7bedd2c3ca040f1e8ea02c6590a93116b1ec78 ]
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 143c253f42bad20357e7e4432087aca747c43384 ]
When hns_assemble_skb() returns NULL to skb, no error return code of
hns_nic_clear_all_rx_fetch() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ae85ddda0f1b341b2d25f5a5e0eff1d42b6ef3df ]
Currently, some bit filed definitions of flow director TCAM
configuration command are incorrect. Since the wrong MSB is
always 0, and these fields are assgined in order, so it still works.
Fix it by redefine them.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b36fc875bcdee56865c444a2cdae17d354a6d5f5 upstream.
The function hclge_fd_convert_tuple() is used to convert tuples
and tuples mask to TCAM x and y. But it misuses the source mac
as source mac mask when convert INNER_SRC_MAC, which may cause
the flow director rule works unexpectedly. So fix it.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c75ec148a316e8cf52274d16b9b422703b96f5ce upstream.
Currently, the driver returns VLAN_VID_MASK for vlan mask field,
when get flow director rule information for rule doesn't use vlan.
It may cause the vlan mask value display as 0xf000 in this
case, like below:
estuary:/$ ethtool -u eth1
50 RX rings available
Total 1 rules
Filter: 2
Rule Type: TCP over IPv4
Src IP addr: 0.0.0.0 mask: 255.255.255.255
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xf000
User-defined: 0x1234 mask: 0x0
Action: Direct to queue 3
Fix it by return 0.
Fixes: 05c2314fe6a8 ("net: hns3: Add support for rule query of flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 67a69f84cab60484f02eb8cbc7a76edffbb28a25 ]
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40fc ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f04bbcbf1e38d192e94bbfa126731a52332c40b1 ]
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d142 ("net: hns3: add phy selftest function")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 65e61e3c2a619c4d4b873885b2d5394025ed117b ]
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5ede3ada3da7f050519112b81badc058190b9f9f ]
The function skb_copy() could return NULL, the return value
need to be checked.
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 61f54de2e9194f01874d5eda12037b0978e77519 ]
hclge_dbg_reg_info[] is defined as an array of packed structure
accidentally. However, this array contains pointers, which are
no longer aligned naturally, and cannot be relocated on PPC64.
Hence, when compile-testing this driver on PPC64 with
CONFIG_RELOCATABLE=y (e.g. PowerPC allyesconfig), there will be
some warnings.
Since each field in structure hclge_qos_pri_map_cmd and
hclge_dbg_bitmap_cmd is type u8, the pragma packed is unnecessary
for these two structures as well, so remove the pragma packed in
hclge_debugfs.h to fix this issue, and this increases
hclge_dbg_reg_info[] by 4 bytes per entry.
Fixes: a582b78dfc33 ("net: hns3: code optimization for debugfs related to "dump reg"")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3364c5ff3ff975b943a7bf47e21a2a4bf20f3fe ]
When unbinding the hns3 driver with the HNS3 VF, I got the following
kernel panic:
[ 265.709989] Unable to handle kernel paging request at virtual address ffff800054627000
[ 265.717928] Mem abort info:
[ 265.720740] ESR = 0x96000047
[ 265.723810] EC = 0x25: DABT (current EL), IL = 32 bits
[ 265.729126] SET = 0, FnV = 0
[ 265.732195] EA = 0, S1PTW = 0
[ 265.735351] Data abort info:
[ 265.738227] ISV = 0, ISS = 0x00000047
[ 265.742071] CM = 0, WnR = 1
[ 265.745055] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000009b54000
[ 265.751753] [ffff800054627000] pgd=0000202ffffff003, p4d=0000202ffffff003, pud=00002020020eb003, pmd=00000020a0dfc003, pte=0000000000000000
[ 265.764314] Internal error: Oops: 96000047 [#1] SMP
[ 265.830357] CPU: 61 PID: 20319 Comm: bash Not tainted 5.9.0+ #206
[ 265.836423] Hardware name: Huawei TaiShan 2280 V2/BC82AMDDA, BIOS 1.05 09/18/2019
[ 265.843873] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--)
[ 265.843890] pc : hclgevf_cmd_uninit+0xbc/0x300
[ 265.861988] lr : hclgevf_cmd_uninit+0xb0/0x300
[ 265.861992] sp : ffff80004c983b50
[ 265.881411] pmr_save: 000000e0
[ 265.884453] x29: ffff80004c983b50 x28: ffff20280bbce500
[ 265.889744] x27: 0000000000000000 x26: 0000000000000000
[ 265.895034] x25: ffff800011a1f000 x24: ffff800011a1fe90
[ 265.900325] x23: ffff0020ce9b00d8 x22: ffff0020ce9b0150
[ 265.905616] x21: ffff800010d70e90 x20: ffff800010d70e90
[ 265.910906] x19: ffff0020ce9b0080 x18: 0000000000000004
[ 265.916198] x17: 0000000000000000 x16: ffff800011ae32e8
[ 265.916201] x15: 0000000000000028 x14: 0000000000000002
[ 265.916204] x13: ffff800011ae32e8 x12: 0000000000012ad8
[ 265.946619] x11: ffff80004c983b50 x10: 0000000000000000
[ 265.951911] x9 : ffff8000115d0888 x8 : 0000000000000000
[ 265.951914] x7 : ffff800011890b20 x6 : c0000000ffff7fff
[ 265.951917] x5 : ffff80004c983930 x4 : 0000000000000001
[ 265.951919] x3 : ffffa027eec1b000 x2 : 2b78ccbbff369100
[ 265.964487] x1 : 0000000000000000 x0 : ffff800054627000
[ 265.964491] Call trace:
[ 265.964494] hclgevf_cmd_uninit+0xbc/0x300
[ 265.964496] hclgevf_uninit_ae_dev+0x9c/0xe8
[ 265.964501] hnae3_unregister_ae_dev+0xb0/0x130
[ 265.964516] hns3_remove+0x34/0x88 [hns3]
[ 266.009683] pci_device_remove+0x48/0xf0
[ 266.009692] device_release_driver_internal+0x114/0x1e8
[ 266.030058] device_driver_detach+0x28/0x38
[ 266.034224] unbind_store+0xd4/0x108
[ 266.037784] drv_attr_store+0x40/0x58
[ 266.041435] sysfs_kf_write+0x54/0x80
[ 266.045081] kernfs_fop_write+0x12c/0x250
[ 266.049076] vfs_write+0xc4/0x248
[ 266.052378] ksys_write+0x74/0xf8
[ 266.055677] __arm64_sys_write+0x24/0x30
[ 266.059584] el0_svc_common.constprop.3+0x84/0x270
[ 266.064354] do_el0_svc+0x34/0xa0
[ 266.067658] el0_svc+0x38/0x40
[ 266.070700] el0_sync_handler+0x8c/0xb0
[ 266.074519] el0_sync+0x140/0x180
It looks like the BAR memory region had already been unmapped before we
start clearing CMDQ registers in it, which is pretty bad and the kernel
happily kills itself because of a Current EL Data Abort (on arm64).
Moving the CMDQ uninitialization a bit early fixes the issue for me.
Fixes: 862d969a3a4d ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20201023051550.793-1-yuzenghui@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a156998fc92d3859c8e820f1583f6d0541d643c3 ]
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
6081.
This patch fixes it by doing the checksum in software.
Reported-by: Li Bing <libing@winhong.com>
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 100e3345c6e719d2291e1efd5de311cc24bb9c0b ]
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efe3fa45f770f1d66e2734ee7a3523c75694ff04 ]
When user had created a FD rule, all the aRFS rules should be clear up.
HNS3 process flow as below:
1.get spin lock of fd_ruls_list
2.clear up all aRFS rules
3.release lock
4.get spin lock of fd_ruls_list
5.creat a rules
6.release lock;
There is a short period of time between step 3 and step 4, which would
creatting some new aRFS FD rules if driver was receiving packet.
So refactor the fd_rule_lock to fix it.
Fixes: 441228875706 ("net: hns3: refine the flow director handle")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a7e90ee5965fafc53d36e8b3205f08c88d7bc11f ]
When the queue depth and queue parameters are modified, there is
a low probability that TX timeout occurs. The two operations cause
the link to be down or up when the watchdog is still working. All
queues are stopped when the link is down. After the carrier is on,
all queues are woken up. If the watchdog detects the link between
the carrier on and wakeup queues, a false TX timeout occurs.
So fix this issue by modifying the sequence of carrier on and queue
wakeup, which is symmetrical to the link down action.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ceca59fb3ed48a693171bd571c4fcbd555b7f1f ]
The content of the TX desc is automatically cleared by the HW
when the HW has sent out the packet to the wire. When desc filling
fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do
the error handling, which miss zeroing of the TX desc and the
checking if a unmapping is needed.
So add the zeroing and checking in hns3_clear_desc() to avoid the
above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in
desc_cb is not valid, because hns3_nic_reclaim_desc() may treat
the desc_cb->type of zero as packet and add to the sent pkt
statistics accordingly.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a06656211304fec653c1931c2ca6d644013b5bbb ]
Enable promisc mode of PF, set VF link state to enable, and
run iperf of the VF, then do self test of the PF. The self test
will fail with a low frequency, and may cause a use-after-free
problem.
[ 87.142126] selftest:000004a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 87.159722] ==================================================================
[ 87.174187] BUG: KASAN: use-after-free in hex_dump_to_buffer+0x140/0x608
[ 87.187600] Read of size 1 at addr ffff003b22828000 by task ethtool/1186
[ 87.201012]
[ 87.203978] CPU: 7 PID: 1186 Comm: ethtool Not tainted 5.5.0-rc4-gfd51c473-dirty #4
[ 87.219306] Hardware name: Huawei TaiShan 2280 V2/BC82AMDA, BIOS TA BIOS 2280-A CS V2.B160.01 01/15/2020
[ 87.238292] Call trace:
[ 87.243173] dump_backtrace+0x0/0x280
[ 87.250491] show_stack+0x24/0x30
[ 87.257114] dump_stack+0xe8/0x140
[ 87.263911] print_address_description.isra.8+0x70/0x380
[ 87.274538] __kasan_report+0x12c/0x230
[ 87.282203] kasan_report+0xc/0x18
[ 87.288999] __asan_load1+0x60/0x68
[ 87.295969] hex_dump_to_buffer+0x140/0x608
[ 87.304332] print_hex_dump+0x140/0x1e0
[ 87.312000] hns3_lb_check_skb_data+0x168/0x170
[ 87.321060] hns3_clean_rx_ring+0xa94/0xfe0
[ 87.329422] hns3_self_test+0x708/0x8c0
The length of packet sent by the selftest process is only
128 + 14 bytes, and the min buffer size of a BD is 256 bytes,
and the receive process will make sure the packet sent by
the selftest process is in the linear part, so only check
the linear part in hns3_lb_check_skb_data().
So fix this use-after-free by using skb_headlen() to dump
skb->data instead of skb->len.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e22b5e728bbb179b912d3a3cd5c25894a89a26a2 ]
When unloading driver, if flag HNS3_NIC_STATE_INITED has been
already cleared, the debugfs will not be uninitialized, so fix it.
Fixes: b2292360bb2a ("net: hns3: Add debugfs framework registration")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5eb01ddfcfb25e6ebc404a41deae946bde776731 ]
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2e8 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68e1006f618e509fc7869259fe83ceec4a95dac3 ]
When fibre port supports auto-negotiation, the IMP(Intelligent
Management Process) processes the speed of auto-negotiation
and the user's speed separately.
For below case, the port will get a not link up problem.
step 1: disables auto-negotiation and sets speed to A, then
the driver's MAC speed will be updated to A.
step 2: enables auto-negotiation and MAC gets negotiated
speed B, then the driver's MAC speed will be updated to B
through querying in periodical task.
step 3: MAC gets new negotiated speed A.
step 4: disables auto-negotiation and sets speed to B before
periodical task query new MAC speed A, the driver will ignore
the speed configuration.
This patch fixes it by skipping speed and duplex checking when
fibre port supports auto-negotiation.
Fixes: 22f48e24a23d ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 47327c9315b2f3ae4ab659457977a26669631f20 ]
The IPv6 address defined in struct in6_addr is specified as
big endian, but there is no specified endian in struct
hclge_fd_rule_tuples, so it will cause a problem if directly
use memcpy() to copy ipv6 address between these two structures
since this field in struct hclge_fd_rule_tuples is little endian.
This patch fixes this problem by using be32_to_cpu() to convert
endian of IPv6 address of struct in6_addr before copying.
Fixes: d93ed94fbeaf ("net: hns3: add aRFS support for PF")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0db7ed397517c8b2be24a0d1abfa15df776908e ]
In the current process, the management table is missing after the
IMP reset. This patch adds the management table to the reset process.
Fixes: f5aac71c0327 ("net: hns3: add manager table initialization for hardware")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49edd6a2c456150870ddcef5b7ed11b21d849e13 ]
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 36c67349a1a1c88b9cf11d7ca7762ababdb38867 ]
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 647522a5ef6401dcdb8ec417421e43fb21910167 ]
When there is a TX timeout, we can tell if the driver or stack
has stopped the queue by looking at state field, and when has
the last packet transmited by looking at trans_start field.
So this patch prints these two field in the
hns3_get_tx_timeo_queue_info().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4fdd0bca6152aa201898454e63cbb255a18ae6e9 ]
When device is resetting, the CMDQ service may be stopped until
reset completed. If a new RAS error occurs at this moment, it
will no be able to clear the RAS source. This patch fixes it
by clear the RAS source after reset complete.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 90b3b339364c76baa2436445401ea9ade040c216 ]
When doing stress test, we get the following trace:
kernel BUG at lib/dynamic_queue_limits.c:26!
Internal error: Oops - BUG: 0 [#1] SMP ARM
Modules linked in: hip04_eth
CPU: 0 PID: 2003 Comm: tDblStackPcap0 Tainted: G O L 4.4.197 #1
Hardware name: Hisilicon A15
task: c3637668 task.stack: de3bc000
PC is at dql_completed+0x18/0x154
LR is at hip04_tx_reclaim+0x110/0x174 [hip04_eth]
pc : [<c041abfc>] lr : [<bf0003a8>] psr: 800f0313
sp : de3bdc2c ip : 00000000 fp : c020fb10
r10: 00000000 r9 : c39b4224 r8 : 00000001
r7 : 00000046 r6 : c39b4000 r5 : 0078f392 r4 : 0078f392
r3 : 00000047 r2 : 00000000 r1 : 00000046 r0 : df5d5c80
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 32c5387d Table: 1e189b80 DAC: 55555555
Process tDblStackPcap0 (pid: 2003, stack limit = 0xde3bc190)
Stack: (0xde3bdc2c to 0xde3be000)
[<c041abfc>] (dql_completed) from [<bf0003a8>] (hip04_tx_reclaim+0x110/0x174 [hip04_eth])
[<bf0003a8>] (hip04_tx_reclaim [hip04_eth]) from [<bf0012c0>] (hip04_rx_poll+0x20/0x388 [hip04_eth])
[<bf0012c0>] (hip04_rx_poll [hip04_eth]) from [<c04c8d9c>] (net_rx_action+0x120/0x374)
[<c04c8d9c>] (net_rx_action) from [<c021eaf4>] (__do_softirq+0x218/0x318)
[<c021eaf4>] (__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac)
[<c021eea0>] (irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4)
[<c0240130>] (msa_irq_exit) from [<c0267ba8>] (__handle_domain_irq+0x110/0x148)
[<c0267ba8>] (__handle_domain_irq) from [<c0201588>] (gic_handle_irq+0xd4/0x118)
[<c0201588>] (gic_handle_irq) from [<c0558360>] (__irq_svc+0x40/0x58)
Exception stack(0xde3bdde0 to 0xde3bde28)
dde0: 00000000 00008001 c3637668 00000000 00000000 a00f0213 dd3627a0 c0af6380
de00: c086d380 a00f0213 c0a22a50 de3bde6c 00000002 de3bde30 c0558138 c055813c
de20: 600f0213 ffffffff
[<c0558360>] (__irq_svc) from [<c055813c>] (_raw_spin_unlock_irqrestore+0x44/0x54)
Kernel panic - not syncing: Fatal exception in interrupt
Pre-modification code:
int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
[...]
[1] priv->tx_head = TX_NEXT(tx_head);
[2] count++;
[3] netdev_sent_queue(ndev, skb->len);
[...]
}
An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2,
tx_head has been updated, but corresponding 'skb->len' has not been
added to dql_queue.
And then
hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim
In hip04_tx_reclaim, because tx_head has been updated,
bytes_compl will plus an additional "skb-> len"
which has not been added to dql_queue. And then
trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
To solve the problem described above, we put
"netdev_sent_queue(ndev, skb->len);"
before
"priv->tx_head = TX_NEXT(tx_head);"
Fixes: a41ea46a9a12 ("net: hisilicon: new hip04 ethernet driver")
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.
This patch fixes this wrong bit mask.
Fixes: 2336f19d7892 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans-up the stray left over code. It has no
functionality impact.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some device only support 4 TCs, but the driver check the total
bandwidth of 8 TCs, so may cause wrong configurations write to
the hw.
This patch uses hdev->tc_max to instead HNAE3_MAX_TC to fix it.
Fixes: e432abfb99e5 ("net: hns3: add common validation in hclge_dcb")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a TC's PFC is disabled or enabled, the RX private buffer for
this TC need to be changed too, otherwise this may cause packet
dropped problem.
This patch fixes it by calling hclge_buffer_alloc to reallocate
buffer when pfc_en changes.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, hns3 driver just directly send specific setting bit
and mask bits of MAC VLAN switch parameter to the firmware, it
can not be compatible with the old firmware, because the old one
ignores mask bits and covers all bits with new setting bits.
So when running with old firmware, the communication between PF
and VF will fail after resetting or configuring spoof check, since
they will do the MAC VLAN switch parameter configuration.
This patch fixes this problem by reading switch parameter firstly,
then just modifies the corresponding bit and sends it to firmware.
Fixes: dd2956eab104 ("net: hns3: not allow SSU loopback while execute ethtool -t dev")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
[1] https://git.kernel.org/torvalds/c/4bd2c03be7
[2] https://patchwork.ozlabs.org/patch/1189139/
Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller")
Cc: lipeng <lipeng321@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
