| Age | Commit message (Collapse) | Author |
|---|
|
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling the locked versions of the read/write PHY ops function pointers
often produces excessively long lines. Shorten these as is done with
the non-locked versions of the PHY register read/write functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
An update to the EEPROM on 82579 will extend a delay in hardware to fix an
issue with WoL not working after a G3->S5 transition which is unrelated to
the driver. However, this extended delay conflicts with nominal operation
of the device when it is initialized by the driver and after every reset
of the hardware (i.e. the driver starts configuring the device before the
hardware is done with it's own configuration work). The workaround for
when the driver is in control of the device is to tell the hardware after
every reset the configuration delay should be the original shorter one.
Some pre-existing variables are renamed generically to be re-used with
new register accesses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace occurrences of 'if (<bool expr> == <1|0>)' with
'if ([!]<bool expr>)'
Replace occurrences of '<bool var> = (<non-bool expr>) ? true : false'
with '<bool var> = <non-bool expr>'.
Replace occurrence of '<bool var> = <non-bool expr>' with
'<bool var> = !!<non-bool expr>'
While the latter replacement is not really necessary, it is done here for
consistency and clarity. No functional changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the
function is used for more than one MAC-family type, and set and use it as a
MAC ops function pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rename e1000e_config_collision_dist() to
e1000e_config_collision_dist_generic() to signify the function is used for
more than one MAC-family type, and set and use it as a MAC ops function
pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Call the MAC ops setup_physical_interface function pointer instead of the
MAC-family-specific function to conform to the rest of the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Replace e1000_check_reset_block() inline function with calls to the PHY ops
check_reset_block function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rename e1000e_setup_link() to e1000e_setup_link_generic() to signify the
function is used for more than one MAC-family type. The 82571-family has
a custom setup_link function which also calls the generic function. The
ich8lan-family has a custom function which should just be called via the
function pointer. The 80003es2lan-family just uses the generic function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rename e1000e_id_led_init() to e1000e_id_led_init_generic() to signify the
function is used for more than one MAC-family type. For the ich8lan MAC
family, some MACs use the generic function and others use the function
e1000_id_led_init_pchlan(). In all cases where e1000e_id_led_init() was
called directly, change to call the function pointer to be consistent with
the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Per ./Documentation/CodingStyle, goto statements are acceptable for the
centralized exiting of functions when there are multiple exit points which
share common work such as cleanup. When no common work is required for
multiple exit points, the function should just return at these exit points
instead of doing an unnecessary jump to a centralized return. This patch
cleans up the inappropriate use of goto statements, and removes unnecessary
variables (or move to a smaller scope) where possible as a result of the
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the unlikely event that e1000_setup_link_ich8lan() returns an error,
the returned error code value is not propagated to the caller of
e1000_init_hw_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ret_val gets initialized to -E1000_ERR_NVM and never set differently, so
get rid of it and just return -E1000_ERR_NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the unlikely event that e1e_wphy() returns an error, the returned error
code is not propogated to the caller of e1000_set_d3_lplu_state_ich8lan().
With this change, there is a rare possibility that ret_val might not get
set so it must be initialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These are a few instances of returning a value that can only be 0 so just
use a 'return 0' to make it more obvious.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the following functions, rename the generic 'out' goto label to the more
descriptive 'release' to indicate the type of common work that is done
before exiting the functions. No functional change, cosmetic only.
e1000_sw_lcd_config_ich8lan()
e1000_oem_bits_config_ich8lan()
e1000_init_phy_wakeup()
e1000e_write_phy_reg_bm()
e1000e_read_phy_reg_bm()
e1000e_read_phy_reg_bm2()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The e1000_init_mac_params_XXX() functions (where XXX is one of the three
MAC-family types 80003es2lan, 82571 and ich8lan) was not meant to require a
pointer to the adapter struct but does require a pointer to the hw struct.
Pass that pointer in to the functions instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
...and convert some goto's which simply return to just return.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Cleanup of some whitespace and indentation of a single code block.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The majority of the e1000e code checks most function return values using a
test like 'if (ret_val)' or 'if (!ret_val)' but there are a few instances
of 'if (ret_val == 0)'. This patch converts the latter to the former for
consistency.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.
Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During bi-directional stress on some 82566/82567 devices, some received
packets were dropped. Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM. However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME). Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.
The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 67fd4fcb (e1000e: convert to stats64) added the ability to update
statistics more accurately and on-demand through the net_device_ops
.ndo_get_stats64 hook, but introduced a locking bug on 82577/8/9 when
linked at half-duplex (seen on kernels with CONFIG_DEBUG_ATOMIC_SLEEP=y and
CONFIG_PROVE_LOCKING=y). The commit introduced code paths that caused a
mutex to be locked in atomic contexts, e.g. an rcu_read_lock is held when
irqbalance reads the stats from /sys/class/net/ethX/statistics causing the
mutex to be locked to read the Phy half-duplex statistics registers.
The mutex was originally introduced to prevent concurrent accesses of
resources (the NVM and Phy) shared by the driver, firmware and hardware
a few years back when there was an issue with the NVM getting corrupted.
It was later split into two mutexes - one for the NVM and one for the Phy
when it was determined the NVM, unlike the Phy, should not be protected by
the software/firmware/hardware semaphore (arbitration of which is done in
part with the SWFLAG bit in the EXTCNF_CTRL register). This latter
semaphore should be sufficient to prevent resource contention of the Phy in
the driver (i.e. the mutex for Phy accesses is not needed), but to be sure
the mutex is replaced with an atomic bit flag which will warn if any
contention is possible.
Also add additional debug output to help determine when the sw/fw/hw
semaphore is owned by the firmware or hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
|
|
When short packets are received with jumbos enabled on 82579, they can be
interpreted to have a receive address that does not match any configured
address. This is due to a hardware bug that can be worked around by
reducing the number of IPG octets added when the packet is transferred from
the PHY to the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PCI device ID 0x1501 has a hardware bug when the link downshifts for
whatever reason which requires a workaround. The workaround already exists
for other similar devices but is not called for 0x1501 (it should be called
for any ICH8-based device that uses a GbE PHY). There is also one other
instance when the workaround should be called - after disabling gigabit
speed when going to Sx.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During suspend, the PHY must be reset for workaround updates to take effect
without restarting auto-negotiation. Also, set the disable GbE and enable
Low Power Link Up (LPLU) if the EEPROM is configured to do likewise in
either D0 or non-D0a instead of just the latter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The initial function and setup tables can be marked as constant.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
|
|
Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM. Remove those duplicates and use the net_device_ops
ndo_set_features. This is based on the original patch submitted by
Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
