summaryrefslogtreecommitdiff
path: root/drivers/net/vxlan.c
AgeCommit message (Collapse)Author
2019-05-02vxlan: test dev->flags & IFF_UP before calling netif_rx()Eric Dumazet
commit 4179cb5a4c924cd233eaadd081882425bc98f44e upstream. netif_rx() must be called under a strict contract. At device dismantle phase, core networking clears IFF_UP and flush_all_backlogs() is called after rcu grace period to make sure no incoming packet might be in a cpu backlog and still referencing the device. Most drivers call netif_rx() from their interrupt handler, and since the interrupts are disabled at device dismantle, netif_rx() does not have to check dev->flags & IFF_UP Virtual drivers do not have this guarantee, and must therefore make the check themselves. Otherwise we risk use-after-free and/or crashes. Note this patch also fixes a small issue that came with commit ce6502a8f957 ("vxlan: fix a use after free in vxlan_encap_bypass"), since the dev->stats.rx_dropped change was done on the wrong device. Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Fixes: ce6502a8f957 ("vxlan: fix a use after free in vxlan_encap_bypass") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Petr Machata <petrm@mellanox.com> Cc: Ido Schimmel <idosch@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2019-02-11vxlan: Fix error path in __vxlan_dev_create()Petr Machata
commit 6db9246871394b3a136cd52001a0763676563840 upstream. When a failure occurs in rtnl_configure_link(), the current code calls unregister_netdevice() to roll back the earlier call to register_netdevice(), and jumps to errout, which calls vxlan_fdb_destroy(). However unregister_netdevice() calls transitively ndo_uninit, which is vxlan_uninit(), and that already takes care of deleting the default FDB entry by calling vxlan_fdb_delete_default(). Since the entry added earlier in __vxlan_dev_create() is exactly the default entry, the cleanup code in the errout block always leads to double free and thus a panic. Besides, since vxlan_fdb_delete_default() always destroys the FDB entry with notification enabled, the deletion of the default entry is notified even before the addition was notified. Instead, move the unregister_netdevice() call after the manual destroy, which solves both problems. Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2018-12-16vxlan: fix default fdb entry netlink notify ordering during netdev createRoopa Prabhu
commit 0241b836732f5f43c3f0fd9e9073c1fb24ea6757 upstream. Problem: In vxlan_newlink, a default fdb entry is added before register_netdev. The default fdb creation function also notifies user-space of the fdb entry on the vxlan device which user-space does not know about yet. (RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex). This patch fixes the user-space netlink notification ordering issue with the following changes: - decouple fdb notify from fdb create. - Move fdb notify after register_netdev. - Call rtnl_configure_link in vxlan newlink handler to notify userspace about the newlink before fdb notify and hence avoiding the user-space race. Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: - Drop changes to vxlan_changelink() - Drop last argument to vxlan_fdb_destroy() - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2018-12-16vxlan: add new fdb alloc and create helpersRoopa Prabhu
commit 25e20e730d56471cffa25419bf2a66078bd55330 upstream. - Add new vxlan_fdb_alloc helper - rename existing vxlan_fdb_create into vxlan_fdb_update: because it really creates or updates an existing fdb entry - move new fdb creation into a separate vxlan_fdb_create Main motivation for this change is to introduce the ability to decouple vxlan fdb creation and notify, used in a later patch. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: - s/vxlan->cfg\.addrmax/vxlan->addrmax/g - Drop src_vni parameters and initialisation of vxlan_fdb::vni - Drop last argument to vxlan_fdb_head() - Drop change to vxlan_changelink()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2018-12-16vxlan: fix a potential issue when create a new vxlan fdb entry.Haishuang Yan
commit 17b463654f41f0aa334efd5a6efeab8a6e9496f7 upstream. vxlan_fdb_append may return error, so add the proper check, otherwise it will cause memory leak. Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Changes in v2: - Unnecessary to initialize rc to zero. Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2017-10-12vxlan: dont migrate permanent fdb entries during learnRoopa Prabhu
commit e0090a9e979de5202c7d16c635dea2f005221073 upstream. This patch fixes vxlan_snoop to not move permanent fdb entries on learn events. This is consistent with the bridge fdb handling of permanent entries. Fixes: 26a41ae60438 ("vxlan: only migrate dynamic FDB entries") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2017-06-05vxlan: correctly validate VXLAN ID against VXLAN_N_VIDMatthias Schiffer
commit 4e37d6911f36545b286d15073f6f2222f840e81c upstream. The incorrect check caused an off-by-one error: the maximum VID 0xffffff was unusable. Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2017-03-16udp: prevent skbs lingering in tunnel socket queuesHannes Frederic Sowa
[ Upstream commit e5aed006be918af163eb397e45aa5ea6cefd5e01 ] In case we find a socket with encapsulation enabled we should call the encap_recv function even if just a udp header without payload is available. The callbacks are responsible for correctly verifying and dropping the packets. Also, in case the header validation fails for geneve and vxlan we shouldn't put the skb back into the socket queue, no one will pick them up there. Instead we can simply discard them in the respective encap_recv functions. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: - Drop changes to geneve - vxlan error checking looked a bit different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2016-01-28vxlan: fix test which detect duplicate vxlan ifaceNicolas Dichtel
commit 07b9b37c227cb8d88d478b4a9c5634fee514ede1 upstream. When a vxlan interface is created, the driver checks that there is not another vxlan interface with the same properties. To do this, it checks the existing vxlan udp socket. Since commit 1c51a9159dde, the creation of the vxlan socket is done only when the interface is set up, thus it breaks that test. Example: $ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0 $ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0 $ ip -br l | grep vxlan vxlan10 DOWN f2:55:1c:6a:fb:00 <BROADCAST,MULTICAST> vxlan11 DOWN 7a:cb:b9:38:59:0d <BROADCAST,MULTICAST> Instead of checking sockets, let's loop over the vxlan iface list. Fixes: 1c51a9159dde ("vxlan: fix race caused by dropping rtnl_unlock") Reported-by: Thomas Faivre <thomas.faivre@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> [ luis: backported to 3.16: used davem's backport to 3.18 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2015-10-19vxlan: set needed headroom correctlyJiri Benc
commit 9dc2ad1008c9f91f55ec6c89ec0f8639dfc91596 upstream. vxlan_setup is called when allocating the net_device, i.e. way before vxlan_newlink (or vxlan_dev_configure) is called. This means vxlan->default_dst is actually unset in vxlan_setup and the condition that sets needed_headroom always takes the else branch. Set the needed_headrom at the point when we have the information about the address family available. Fixes: e4c7ed415387c ("vxlan: add ipv6 support") Fixes: 2853af6a2ea1a ("vxlan: use dev->needed_headroom instead of dev->hard_header_len") CC: Cong Wang <cwang@twopensource.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> [ luis: backported to 3.16: - initialise needed_headrom in vxlan_newlink() instead of vxlan_dev_configure() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2015-01-05udptunnel: Add SKB_GSO_UDP_TUNNEL during gro_complete.Jesse Gross
commit cfdf1e1ba5bf55e095cf4bcaa9585c4759f239e8 upstream. When doing GRO processing for UDP tunnels, we never add SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol is added (such as SKB_GSO_TCPV4). The result is that if the packet is later resegmented we will do GSO but not treat it as a tunnel. This results in UDP fragmentation of the outer header instead of (i.e.) TCP segmentation of the inner header as was originally on the wire. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> [ luis: backported to 3.16: - dropped changes to net/ipv4/fou.c - inlined call to udp_tunnel_gro_complete() in drivers/net/vxlan.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-12-15Fix race condition between vxlan_sock_add and vxlan_sock_releaseMarcelo Leitner
commit 00c83b01d58068dfeb2e1351cca6fccf2a83fa8f upstream. Currently, when trying to reuse a socket, vxlan_sock_add will grab vn->sock_lock, locate a reusable socket, inc refcount and release vn->sock_lock. But vxlan_sock_release() will first decrement refcount, and then grab that lock. refcnt operations are atomic but as currently we have deferred works which hold vs->refcnt each, this might happen, leading to a use after free (specially after vxlan_igmp_leave): CPU 1 CPU 2 deferred work vxlan_sock_add ... ... spin_lock(&vn->sock_lock) vs = vxlan_find_sock(); vxlan_sock_release dec vs->refcnt, reaches 0 spin_lock(&vn->sock_lock) vxlan_sock_hold(vs), refcnt=1 spin_unlock(&vn->sock_lock) hlist_del_rcu(&vs->hlist); vxlan_notify_del_rx_port(vs) spin_unlock(&vn->sock_lock) So when we look for a reusable socket, we check if it wasn't freed already before reusing it. Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-11-27vxlan: Do not reuse sockets for a different address familyMarcelo Leitner
commit 19ca9fc1445b76b60d34148f7ff837b055f5dcf3 upstream. Currently, we only match against local port number in order to reuse socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will follow. The following steps reproduce it: # ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \ srcport 5000 6000 dev eth0 # ip link add vxlan7 type vxlan id 43 group ff0e::110 \ srcport 5000 6000 dev eth0 # ip link set vxlan6 up # ip link set vxlan7 up <panic> [ 4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 ... [ 4.188076] Call Trace: [ 4.188085] [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630 [ 4.188098] [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan] [ 4.188113] [<ffffffff810a3430>] process_one_work+0x220/0x710 [ 4.188125] [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710 [ 4.188138] [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0 [ 4.188149] [<ffffffff810a3920>] ? process_one_work+0x710/0x710 So address family must also match in order to reuse a socket. Reported-by: Jean-Tsung Hsiao <jhsiao@redhat.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-11-05vxlan: fix a free after useLi RongQing
commit 7a9f526fc3ee49b6034af2f243676ee0a27dcaa8 upstream. pskb_may_pull maybe change skb->data and make eth pointer oboslete, so eth needs to reload Fixes: 91269e390d062 ("vxlan: using pskb_may_pull as early as possible") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-11-05vxlan: using pskb_may_pull as early as possibleLi RongQing
commit 91269e390d062b526432f2ef1352b8df82e0e0bc upstream. pskb_may_pull should be used to check if skb->data has enough space, skb->len can not ensure that. Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-11-05vxlan: fix a use after free in vxlan_encap_bypassLi RongQing
commit ce6502a8f9572179f044a4d62667c4645256d6e4 upstream. when netif_rx() is done, the netif_rx handled skb maybe be freed, and should not be used. Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
2014-10-15vxlan: fix incorrect initializer in union vxlan_addrGerhard Stenzel
[ Upstream commit a45e92a599e77ee6a850eabdd0141633fde03915 ] The first initializer in the following union vxlan_addr ipa = { .sin.sin_addr.s_addr = tip, .sa.sa_family = AF_INET, }; is optimised away by the compiler, due to the second initializer, therefore initialising .sin.sin_addr.s_addr always to 0. This results in netlink messages indicating a L3 miss never contain the missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions. The problem affects user space programs relying on an IP address being sent as part of a netlink message indicating a L3 miss. Changing .sa.sa_family = AF_INET, to .sin.sin_family = AF_INET, fixes the problem. Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28neighbour : fix ndm_type type error issueJun Zhao
ndm_type means L3 address type, in neighbour proxy and vxlan, it's RTN_UNICAST. NDA_DST is for netlink TLV type, hence it's not right value in this context. Signed-off-by: Jun Zhao <mypopydev@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-15vxlan: Checksum fixesTom Herbert
Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet header to work properly with checksum complete. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-13vxlan: use dev->needed_headroom instead of dev->hard_header_lenCong Wang
When we mirror packets from a vxlan tunnel to other device, the mirror device should see the same packets (that is, without outer header). Because vxlan tunnel sets dev->hard_header_len, tcf_mirred() resets mac header back to outer mac, the mirror device actually sees packets with outer headers Vxlan tunnel should set dev->needed_headroom instead of dev->hard_header_len, like what other ip tunnels do. This fixes the above problem. Cc: "David S. Miller" <davem@davemloft.net> Cc: stephen hemminger <stephen@networkplumber.org> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-11net: Add skb_gro_postpull_rcsum to udp and vxlanTom Herbert
Need to gro_postpull_rcsum for GRO to work with checksum complete. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04vxlan: Add support for UDP checksums (v4 sending, v6 zero csums)Tom Herbert
Added VXLAN link configuration for sending UDP checksums, and allowing TX and RX of UDP6 checksums. Also, call common iptunnel_handle_offloads and added GSO support for checksums. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13net: get rid of SET_ETHTOOL_OPSWilfried Klaebe
net: get rid of SET_ETHTOOL_OPS Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone. This does that. Mostly done via coccinelle script: @@ struct ethtool_ops *ops; struct net_device *dev; @@ - SET_ETHTOOL_OPS(dev, ops); + dev->ethtool_ops = ops; Compile tested only, but I'd seriously wonder if this broke anything. Suggested-by: Dave Miller <davem@davemloft.net> Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24vxlan: add x-netns supportNicolas Dichtel
This patch allows to switch the netns when packet is encapsulated or decapsulated. The vxlan socket is openned into the i/o netns, ie into the netns where encapsulated packets are received. The socket lookup is done into this netns to find the corresponding vxlan tunnel. After decapsulation, the packet is injecting into the corresponding interface which may stand to another netns. When one of the two netns is removed, the tunnel is destroyed. Configuration example: ip netns add netns1 ip netns exec netns1 ip link set lo up ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0 ip link set vxlan10 netns netns1 ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10 ip netns exec netns1 ip link set vxlan10 up Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-23vxlan: ensure to advertise the right fdb remoteNicolas Dichtel
The goal of this patch is to fix rtnelink notification. The main problem was about notification for fdb entry with more than one remote. Before the patch, when a remote was added to an existing fdb entry, the kernel advertised the first remote instead of the added one. Also when a remote was removed from a fdb entry with several remotes, the deleted remote was not advertised. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-15ipv4: add a sock pointer to dst->output() path.Eric Dumazet
In the dst->output() path for ipv4, the code assumes the skb it has to transmit is attached to an inet socket, specifically via ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the provider of the packet is an AF_PACKET socket. The dst->output() method gets an additional 'struct sock *sk' parameter. This needs a cascade of changes so that this parameter can be propagated from vxlan to final consumer. Fixes: 8f646c922d55 ("vxlan: keep original skb ownership") Reported-by: lucien xin <lucien.xin@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-03net: vxlan: fix crash when interface is created with no groupMike Rapoport
If the vxlan interface is created without explicit group definition, there are corner cases which may cause kernel panic. For instance, in the following scenario: node A: $ ip link add dev vxlan42 address 2c:c2:60:00:10:20 type vxlan id 42 $ ip addr add dev vxlan42 10.0.0.1/24 $ ip link set up dev vxlan42 $ arp -i vxlan42 -s 10.0.0.2 2c:c2:60:00:01:02 $ bridge fdb add dev vxlan42 to 2c:c2:60:00:01:02 dst <IPv4 address> $ ping 10.0.0.2 node B: $ ip link add dev vxlan42 address 2c:c2:60:00:01:02 type vxlan id 42 $ ip addr add dev vxlan42 10.0.0.2/24 $ ip link set up dev vxlan42 $ arp -i vxlan42 -s 10.0.0.1 2c:c2:60:00:10:20 node B crashes: vxlan42: 2c:c2:60:00:10:20 migrated from 4011:eca4:c0a8:6466:c0a8:6415:8e09:2118 to (invalid address) vxlan42: 2c:c2:60:00:10:20 migrated from 4011:eca4:c0a8:6466:c0a8:6415:8e09:2118 to (invalid address) BUG: unable to handle kernel NULL pointer dereference at 0000000000000046 IP: [<ffffffff8143c459>] ip6_route_output+0x58/0x82 PGD 7bd89067 PUD 7bd4e067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.0-rc8-hvx-xen-00019-g97a5221-dirty #154 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff88007c774f50 ti: ffff88007c79c000 task.ti: ffff88007c79c000 RIP: 0010:[<ffffffff8143c459>] [<ffffffff8143c459>] ip6_route_output+0x58/0x82 RSP: 0018:ffff88007fd03668 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffff8186a000 RCX: 0000000000000040 RDX: 0000000000000000 RSI: ffff88007b0e4a80 RDI: ffff88007fd03754 RBP: ffff88007fd03688 R08: ffff88007b0e4a80 R09: 0000000000000000 R10: 0200000a0100000a R11: 0001002200000000 R12: ffff88007fd03740 R13: ffff88007b0e4a80 R14: ffff88007b0e4a80 R15: ffff88007bba0c50 FS: 0000000000000000(0000) GS:ffff88007fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000046 CR3: 000000007bb60000 CR4: 00000000000006e0 Stack: 0000000000000000 ffff88007fd037a0 ffffffff8186a000 ffff88007fd03740 ffff88007fd036c8 ffffffff814320bb 0000000000006e49 ffff88007b8b7360 ffff88007bdbf200 ffff88007bcbc000 ffff88007b8b7000 ffff88007b8b7360 Call Trace: <IRQ> [<ffffffff814320bb>] ip6_dst_lookup_tail+0x2d/0xa4 [<ffffffff814322a5>] ip6_dst_lookup+0x10/0x12 [<ffffffff81323b4e>] vxlan_xmit_one+0x32a/0x68c [<ffffffff814a325a>] ? _raw_spin_unlock_irqrestore+0x12/0x14 [<ffffffff8104c551>] ? lock_timer_base.isra.23+0x26/0x4b [<ffffffff8132451a>] vxlan_xmit+0x66a/0x6a8 [<ffffffff8141a365>] ? ipt_do_table+0x35f/0x37e [<ffffffff81204ba2>] ? selinux_ip_postroute+0x41/0x26e [<ffffffff8139d0c1>] dev_hard_start_xmit+0x2ce/0x3ce [<ffffffff8139d491>] __dev_queue_xmit+0x2d0/0x392 [<ffffffff813b380f>] ? eth_header+0x28/0xb5 [<ffffffff8139d569>] dev_queue_xmit+0xb/0xd [<ffffffff813a5aa6>] neigh_resolve_output+0x134/0x152 [<ffffffff813db741>] ip_finish_output2+0x236/0x299 [<ffffffff813dc074>] ip_finish_output+0x98/0x9d [<ffffffff813dc749>] ip_output+0x62/0x67 [<ffffffff813da9f2>] dst_output+0xf/0x11 [<ffffffff813dc11c>] ip_local_out+0x1b/0x1f [<ffffffff813dcf1b>] ip_send_skb+0x11/0x37 [<ffffffff813dcf70>] ip_push_pending_frames+0x2f/0x33 [<ffffffff813ff732>] icmp_push_reply+0x106/0x115 [<ffffffff813ff9e4>] icmp_reply+0x142/0x164 [<ffffffff813ffb3b>] icmp_echo.part.16+0x46/0x48 [<ffffffff813c1d30>] ? nf_iterate+0x43/0x80 [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813ffb62>] icmp_echo+0x25/0x27 [<ffffffff814005f7>] icmp_rcv+0x1d2/0x20a [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813d810d>] ip_local_deliver_finish+0xd6/0x14f [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813d7fde>] NF_HOOK.constprop.10+0x4c/0x53 [<ffffffff813d82bf>] ip_local_deliver+0x4a/0x4f [<ffffffff813d7f7b>] ip_rcv_finish+0x253/0x26a [<ffffffff813d7d28>] ? inet_add_protocol+0x3e/0x3e [<ffffffff813d7fde>] NF_HOOK.constprop.10+0x4c/0x53 [<ffffffff813d856a>] ip_rcv+0x2a6/0x2ec [<ffffffff8139a9a0>] __netif_receive_skb_core+0x43e/0x478 [<ffffffff812a346f>] ? virtqueue_poll+0x16/0x27 [<ffffffff8139aa2f>] __netif_receive_skb+0x55/0x5a [<ffffffff8139aaaa>] process_backlog+0x76/0x12f [<ffffffff8139add8>] net_rx_action+0xa2/0x1ab [<ffffffff81047847>] __do_softirq+0xca/0x1d1 [<ffffffff81047ace>] irq_exit+0x3e/0x85 [<ffffffff8100b98b>] do_IRQ+0xa9/0xc4 [<ffffffff814a37ad>] common_interrupt+0x6d/0x6d <EOI> [<ffffffff810378db>] ? native_safe_halt+0x6/0x8 [<ffffffff810110c7>] default_idle+0x9/0xd [<ffffffff81011694>] arch_cpu_idle+0x13/0x1c [<ffffffff8107480d>] cpu_startup_entry+0xbc/0x137 [<ffffffff8102e741>] start_secondary+0x1a0/0x1a5 Code: 24 14 e8 f1 e5 01 00 31 d2 a8 32 0f 95 c2 49 8b 44 24 2c 49 0b 44 24 24 74 05 83 ca 04 eb 1c 4d 85 ed 74 17 49 8b 85 a8 02 00 00 <66> 8b 40 46 66 c1 e8 07 83 e0 07 c1 e0 03 09 c2 4c 89 e6 48 89 RIP [<ffffffff8143c459>] ip6_route_output+0x58/0x82 RSP <ffff88007fd03668> CR2: 0000000000000046 ---[ end trace 4612329caab37efd ]--- When vxlan interface is created without explicit group definition, the default_dst protocol family is initialiazed to AF_UNSPEC and the driver assumes IPv4 configuration. On the other side, the default_dst protocol family is used to differentiate between IPv4 and IPv6 cases and, since, AF_UNSPEC != AF_INET, the processing takes the IPv6 path. Making the IPv4 assumption explicit by settting default_dst protocol family to AF_INET4 and preventing mixing of IPv4 and IPv6 addresses in snooped fdb entries fixes the corner case crashes. Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: Documentation/devicetree/bindings/net/micrel-ks8851.txt net/core/netpoll.c The net/core/netpoll.c conflict is a bug fix in 'net' happening to code which is completely removed in 'net-next'. In micrel-ks8851.txt we simply have overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-24vxlan: fix nonfunctional neigh_reduce()David Stevens
The VXLAN neigh_reduce() code is completely non-functional since check-in. Specific errors: 1) The original code drops all packets with a multicast destination address, even though neighbor solicitations are sent to the solicited-node address, a multicast address. The code after this check was never run. 2) The neighbor table lookup used the IPv6 header destination, which is the solicited node address, rather than the target address from the neighbor solicitation. So neighbor lookups would always fail if it got this far. Also for L3MISSes. 3) The code calls ndisc_send_na(), which does a send on the tunnel device. The context for neigh_reduce() is the transmit path, vxlan_xmit(), where the host or a bridge-attached neighbor is trying to transmit a neighbor solicitation. To respond to it, the tunnel endpoint needs to do a *receive* of the appropriate neighbor advertisement. Doing a send, would only try to send the advertisement, encapsulated, to the remote destinations in the fdb -- hosts that definitely did not do the corresponding solicitation. 4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the isrouter flag in the advertisement. This has nothing to do with whether or not the target is a router, and generally won't be set since the tunnel endpoint is bridging, not routing, traffic. The patch below creates a proxy neighbor advertisement to respond to neighbor solicitions as intended, providing proper IPv6 support for neighbor reduction. Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-18vxlan: fix potential NULL dereference in arp_reduce()David Stevens
This patch fixes a NULL pointer dereference in the event of an skb allocation failure in arp_reduce(). Signed-Off-By: David L Stevens <dlstevens@us.ibm.com> Acked-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26vxlan: remove unused port variable in vxlan_udp_encap_recv()Pablo Neira Ayuso
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-14net: introduce netdev_alloc_pcpu_stats() for driversWANG Cong
There are many drivers calling alloc_percpu() to allocate pcpu stats and then initializing ->syncp. So just introduce a helper function for them. Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-01vxlan: remove extra newline after function definitionDaniel Baluta
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-30net/vxlan: Go over all candidate streams for GRO matchingOr Gerlitz
The loop in vxlan_gro_receive() over the current set of candidates for coalescing was wrongly aborted once a match was found. In rare cases, this can cause a false-positives matching in the next layer GRO checks. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-23net/vxlan: Share RX skb de-marking and checksum checks with ovsOr Gerlitz
Make sure the practice set by commit 0afb166 "vxlan: Add capability of Rx checksum offload for inner packet" is applied when the skb goes through the portion of the RX code which is shared between vxlan netdevices and ovs vxlan port instances. Cc: Joseph Gasparakis <joseph.gasparakis@intel.com> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-22net: vxlan: convert to act as a pernet subsystemDaniel Borkmann
As per suggestion from Eric W. Biederman, vxlan should be using {un,}register_pernet_subsys() instead of {un,}register_pernet_device() to ensure the vxlan_net structure is initialized before and cleaned up after all network devices in a given network namespace i.e. when dealing with network notifiers. This is similarly handeled already in commit 91e2ff3528ac ("net: Teach vlans to cleanup as a pernet subsystem") and, thus, improves upon fd27e0d44a89 ("net: vxlan: do not use vxlan_net before checking event type"). Just as in 91e2ff3528ac, we do not need to explicitly handle deletion of vxlan devices as network namespace exit calls dellink on all remaining virtual devices, and rtnl_link_unregister() calls dellink on all outstanding devices in that network namespace, so we can entirely drop the pernet exit operation as well. Moreover, on vxlan module exit, rcu_barrier() is called by netns since commit 3a765edadb28 ("netns: Add an explicit rcu_barrier to unregister_pernet_{device|subsys}"), so this may be omitted. Tested with various scenarios and works well on my side. Suggested-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-21net: Add GRO support for vxlan trafficOr Gerlitz
Add GRO handlers for vxlann, by using the UDP GRO infrastructure. For single TCP session that goes through vxlan tunneling I got nice improvement from 6.8Gbs to 11.5Gbs --> UDP/VXLAN GRO disabled $ netperf -H 192.168.52.147 -c -C $ netperf -t TCP_STREAM -H 192.168.52.147 -c -C MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.52.147 () port 0 AF_INET Recv Send Send Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size Size Size Time Throughput local remote local remote bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB 87380 65536 65536 10.00 6799.75 12.54 24.79 0.604 1.195 --> UDP/VXLAN GRO enabled $ netperf -t TCP_STREAM -H 192.168.52.147 -c -C MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.52.147 () port 0 AF_INET Recv Send Send Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size Size Size Time Throughput local remote local remote bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB 87380 65536 65536 10.00 11562.72 24.90 20.34 0.706 0.577 Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-21net: add vxlan descriptionJesse Brandeburg
Add a description to the vxlan module, helping save the world from the minions of destruction and confusion. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-17net: vxlan: do not use vxlan_net before checking event typeDaniel Borkmann
Jesse Brandeburg reported that commit acaf4e70997f caused a panic when adding a network namespace while vxlan module was present in the system: [<ffffffff814d0865>] vxlan_lowerdev_event+0xf5/0x100 [<ffffffff816e9e5d>] notifier_call_chain+0x4d/0x70 [<ffffffff810912be>] __raw_notifier_call_chain+0xe/0x10 [<ffffffff810912d6>] raw_notifier_call_chain+0x16/0x20 [<ffffffff815d9610>] call_netdevice_notifiers_info+0x40/0x70 [<ffffffff815d9656>] call_netdevice_notifiers+0x16/0x20 [<ffffffff815e1bce>] register_netdevice+0x1be/0x3a0 [<ffffffff815e1dce>] register_netdev+0x1e/0x30 [<ffffffff814cb94a>] loopback_net_init+0x4a/0xb0 [<ffffffffa016ed6e>] ? lockd_init_net+0x6e/0xb0 [lockd] [<ffffffff815d6bac>] ops_init+0x4c/0x150 [<ffffffff815d6d23>] setup_net+0x73/0x110 [<ffffffff815d725b>] copy_net_ns+0x7b/0x100 [<ffffffff81090e11>] create_new_namespaces+0x101/0x1b0 [<ffffffff81090f45>] copy_namespaces+0x85/0xb0 [<ffffffff810693d5>] copy_process.part.26+0x935/0x1500 [<ffffffff811d5186>] ? mntput+0x26/0x40 [<ffffffff8106a15c>] do_fork+0xbc/0x2e0 [<ffffffff811b7f2e>] ? ____fput+0xe/0x10 [<ffffffff81089c5c>] ? task_work_run+0xac/0xe0 [<ffffffff8106a406>] SyS_clone+0x16/0x20 [<ffffffff816ee689>] stub_clone+0x69/0x90 [<ffffffff816ee329>] ? system_call_fastpath+0x16/0x1b Apparently loopback device is being registered first and thus we receive an event notification when vxlan_net is not ready. Hence, when we call net_generic() and request vxlan_net_id, we seem to access garbage at that point in time. In setup_net() where we set up a newly allocated network namespace, we traverse the list of pernet ops ... list_for_each_entry(ops, &pernet_list, list) { error = ops_init(ops, net); if (error < 0) goto out_undo; } ... and loopback_net_init() is invoked first here, so in the middle of setup_net() we get this notification in vxlan. As currently we only care about devices that unregister, move access through net_generic() there. Fix is based on Cong Wang's proposal, but only changes what is needed here. It sucks a bit as we only work around the actual cure: right now it seems the only way to check if a netns actually finished traversing all init ops would be to check if it's part of net_namespace_list. But that I find quite expensive each time we go through a notifier callback. Anyway, did a couple of tests and it seems good for now. Fixes: acaf4e70997f ("net: vxlan: when lower dev unregisters remove vxlan dev as well") Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-14net: vxlan: properly cleanup devs on module unloadDaniel Borkmann
We should use vxlan_dellink() handler in vxlan_exit_net(), since i) we're not in fast-path and we should be consistent in dismantle just as we would remove a device through rtnl ops, and more importantly, ii) in case future code will kfree() memory in vxlan_dellink(), we would leak it right here unnoticed. Therefore, do not only half of the cleanup work, but make it properly. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-14net: vxlan: when lower dev unregisters remove vxlan dev as wellDaniel Borkmann
We can create a vxlan device with an explicit underlying carrier. In that case, when the carrier link is being deleted from the system (e.g. due to module unload) we should also clean up all created vxlan devices on top of it since otherwise we're in an inconsistent state in vxlan device. In that case, the user needs to remove all such devices, while in case of other virtual devs that sit on top of physical ones, it is usually the case that these devices do unregister automatically as well and do not leave the burden on the user. This work is not necessary when vxlan device was not created with a real underlying device, as connections can resume in that case when driver is plugged again. But at least for the other cases, we should go ahead and do the cleanup on removal. We don't register the notifier during vxlan_newlink() here since I consider this event rather rare, and therefore we should not bloat vxlan's core structure unecessary. Also, we can simply make use of unregister_netdevice_many() to batch that. fdb is flushed upon ndo_stop(). E.g. `ip -d link show vxlan13` after carrier removal before this patch: 5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0 vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300 ^^^^^ Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-14vxlan: use __dev_get_by_index instead of dev_get_by_index to find interfaceYing Xue
The following call chains indicate that vxlan_fdb_parse() is under rtnl_lock protection. So if we use __dev_get_by_index() instead of dev_get_by_index() to find interface handler in it, this would help us avoid to change interface reference counter. rtnetlink_rcv() rtnl_lock() netlink_rcv_skb() rtnl_fdb_add() vxlan_fdb_add() vxlan_fdb_parse() rtnl_unlock() rtnetlink_rcv() rtnl_lock() netlink_rcv_skb() rtnl_fdb_del() vxlan_fdb_del() vxlan_fdb_parse() rtnl_unlock() Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Ying Xue <ying.xue@windriver.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-06Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c net/ipv6/ip6_tunnel.c net/ipv6/ip6_vti.c ipv6 tunnel statistic bug fixes conflicting with consolidation into generic sw per-cpu net stats. qlogic conflict between queue counting bug fix and the addition of multiple MAC address support. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-06vxlan: keep original skb ownershipEric Dumazet
Sathya Perla posted a patch trying to address following problem : <quote> The vxlan driver sets itself as the socket owner for all the TX flows it encapsulates (using vxlan_set_owner()) and assigns it's own skb destructor. This causes all tunneled traffic to land up on only one TXQ as all encapsulated skbs refer to the vxlan socket and not the original socket. Also, the vxlan skb destructor breaks some functionality for tunneled traffic like wmem accounting and as TCP small queues and FQ/pacing packet scheduler. </quote> I reworked Sathya patch and added some explanations. vxlan_xmit() can avoid one skb_clone()/dev_kfree_skb() pair and gain better drop monitor accuracy, by calling kfree_skb() when appropriate. The UDP socket used by vxlan to perform encapsulation of xmit packets do not need to be alive while packets leave vxlan code. Its better to keep original socket ownership to get proper feedback from qdisc and NIC layers. We use skb->sk to A) control amount of bytes/packets queued on behalf of a socket, but prior vxlan code did the skb->sk transfert without any limit/control on vxlan socket sk_sndbuf. B) security purposes (as selinux) or netfilter uses, and I do not think anything is prepared to handle vxlan stacked case in this area. By not changing ownership, vxlan tunnels behave like other tunnels. As Stephen mentioned, we might do the same change in L2TP. Reported-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-04net: unify the pcpu_tstats and br_cpu_netstats as oneLi RongQing
They are same, so unify them as one, pcpu_sw_netstats. Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats from if_tunnel and remove br_cpu_netstats from br_private.h Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-03{vxlan, inet6} Mark vxlan_dev flags with VXLAN_F_IPV6 properlyfan.du
Even if user doesn't supply the physical netdev to attach vxlan dev to, and at the same time user want to vxlan sit top of IPv6, mark vxlan_dev flags with VXLAN_F_IPV6 to create IPv6 based socket. Otherwise kernel crashes safely every time spitting below messages, Steps to reproduce: ip link add vxlan0 type vxlan id 42 group ff0e::110 ip link set vxlan0 up [ 62.656266] BUG: unable to handle kernel NULL pointer dereference[ 62.656320] ip (3008) used greatest stack depth: 3912 bytes left at 0000000000000046 [ 62.656423] IP: [<ffffffff816d822d>] ip6_route_output+0xbd/0xe0 [ 62.656525] PGD 2c966067 PUD 2c9a2067 PMD 0 [ 62.656674] Oops: 0000 [#1] SMP [ 62.656781] Modules linked in: vxlan netconsole deflate zlib_deflate af_key [ 62.657083] CPU: 1 PID: 2128 Comm: whoopsie Not tainted 3.12.0+ #182 [ 62.657083] Hardware name: innotek GmbH VirtualBox, BIOS VirtualBox 12/01/2006 [ 62.657083] task: ffff88002e2335d0 ti: ffff88002c94c000 task.ti: ffff88002c94c000 [ 62.657083] RIP: 0010:[<ffffffff816d822d>] [<ffffffff816d822d>] ip6_route_output+0xbd/0xe0 [ 62.657083] RSP: 0000:ffff88002fd038f8 EFLAGS: 00210296 [ 62.657083] RAX: 0000000000000000 RBX: ffff88002fd039e0 RCX: 0000000000000000 [ 62.657083] RDX: ffff88002fd0eb68 RSI: ffff88002fd0d278 RDI: ffff88002fd0d278 [ 62.657083] RBP: ffff88002fd03918 R08: 0000000002000000 R09: 0000000000000000 [ 62.657083] R10: 00000000000001ff R11: 0000000000000000 R12: 0000000000000001 [ 62.657083] R13: ffff88002d96b480 R14: ffffffff81c8e2c0 R15: 0000000000000001 [ 62.657083] FS: 0000000000000000(0000) GS:ffff88002fd00000(0063) knlGS:00000000f693b740 [ 62.657083] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 [ 62.657083] CR2: 0000000000000046 CR3: 000000002c9d2000 CR4: 00000000000006e0 [ 62.657083] Stack: [ 62.657083] ffff88002fd03a40 ffffffff81c8e2c0 ffff88002fd039e0 ffff88002d96b480 [ 62.657083] ffff88002fd03958 ffffffff816cac8b ffff880019277cc0 ffff8800192b5d00 [ 62.657083] ffff88002d5bc000 ffff880019277cc0 0000000000001821 0000000000000001 [ 62.657083] Call Trace: [ 62.657083] <IRQ> [ 62.657083] [<ffffffff816cac8b>] ip6_dst_lookup_tail+0xdb/0xf0 [ 62.657083] [<ffffffff816caea0>] ip6_dst_lookup+0x10/0x20 [ 62.657083] [<ffffffffa0020c13>] vxlan_xmit_one+0x193/0x9c0 [vxlan] [ 62.657083] [<ffffffff8137b3b7>] ? account+0xc7/0x1f0 [ 62.657083] [<ffffffffa0021513>] vxlan_xmit+0xd3/0x400 [vxlan] [ 62.657083] [<ffffffff8161390d>] dev_hard_start_xmit+0x49d/0x5e0 [ 62.657083] [<ffffffff81613d29>] dev_queue_xmit+0x2d9/0x480 [ 62.657083] [<ffffffff817cb854>] ? _raw_write_unlock_bh+0x14/0x20 [ 62.657083] [<ffffffff81630565>] ? eth_header+0x35/0xe0 [ 62.657083] [<ffffffff8161bc5e>] neigh_resolve_output+0x11e/0x1e0 [ 62.657083] [<ffffffff816ce0e0>] ? ip6_fragment+0xad0/0xad0 [ 62.657083] [<ffffffff816cb465>] ip6_finish_output2+0x2f5/0x470 [ 62.657083] [<ffffffff816ce166>] ip6_finish_output+0x86/0xc0 [ 62.657083] [<ffffffff816ce218>] ip6_output+0x78/0xb0 [ 62.657083] [<ffffffff816eadd6>] mld_sendpack+0x256/0x2a0 [ 62.657083] [<ffffffff816ebd8c>] mld_ifc_timer_expire+0x17c/0x290 [ 62.657083] [<ffffffff816ebc10>] ? igmp6_timer_handler+0x80/0x80 [ 62.657083] [<ffffffff816ebc10>] ? igmp6_timer_handler+0x80/0x80 [ 62.657083] [<ffffffff81051065>] call_timer_fn+0x45/0x150 [ 62.657083] [<ffffffff816ebc10>] ? igmp6_timer_handler+0x80/0x80 [ 62.657083] [<ffffffff81052353>] run_timer_softirq+0x1f3/0x2a0 [ 62.657083] [<ffffffff8102dfd8>] ? lapic_next_event+0x18/0x20 [ 62.657083] [<ffffffff8109e36f>] ? clockevents_program_event+0x6f/0x110 [ 62.657083] [<ffffffff8104a2f6>] __do_softirq+0xd6/0x2b0 [ 62.657083] [<ffffffff8104a75e>] irq_exit+0x7e/0xa0 [ 62.657083] [<ffffffff8102ea15>] smp_apic_timer_interrupt+0x45/0x60 [ 62.657083] [<ffffffff817d3eca>] apic_timer_interrupt+0x6a/0x70 [ 62.657083] <EOI> [ 62.657083] [<ffffffff817d4a35>] ? sysenter_dispatch+0x7/0x1a [ 62.657083] Code: 4d 8b 85 a8 02 00 00 4c 89 e9 ba 03 04 00 00 48 c7 c6 c0 be 8d 81 48 c7 c7 48 35 a3 81 31 c0 e8 db 68 0e 00 49 8b 85 a8 02 00 00 <0f> b6 40 46 c0 e8 05 0f b6 c0 c1 e0 03 41 09 c4 e9 77 ff ff ff [ 62.657083] RIP [<ffffffff816d822d>] ip6_route_output+0xbd/0xe0 [ 62.657083] RSP <ffff88002fd038f8> [ 62.657083] CR2: 0000000000000046 [ 62.657083] ---[ end trace ba8a9583d7cd1934 ]--- [ 62.657083] Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by: Fan Du <fan.du@windriver.com> Reported-by: Ryan Whelan <rcwhelan@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-22net: vxlan: use custom ndo_change_mtu handlerDaniel Borkmann
When adding a new vxlan device to an "underlying carrier" (here: dst->remote_ifindex), the MTU size assigned to the vxlan device is the MTU at setup time of the carrier - needed headroom, when adding a vxlan device w/o explicit carrier, then it defaults to 1500. In case of an explicit carrier that supports jumbo frames, we currently cannot change vxlan MTU via ip(8) to > 1500 in post-setup time, as vxlan driver uses eth_change_mtu() as default method for manually setting MTU. Hence, use a custom implementation that only falls back to eth_change_mtu() in case we didn't use a dev parameter on device setup time, and otherwise allow a max MTU setting of the carrier incl. adjustment for headroom. Reported-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/intel/i40e/i40e_main.c drivers/net/macvtap.c Both minor merge hassles, simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-17net: Change skb_get_rxhash to skb_get_hashTom Herbert
Changing name of function as part of making the hash in skbuff to be generic property, not just for receive path. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-11vxlan: leave multicast group when vxlan device downGao feng
vxlan_group_used only allows device to leave multicast group when the remote_ip of this vxlan device is difference from other vxlan devices' remote_ip. this will cause device not leave multicast group untile the vn_sock of this vxlan deivce being released. The check in vxlan_group_used is not quite precise. since even the remote_ip is same, but these vxlan devices may use different lower devices, and they may use different vn_socks. Only when some vxlan devices use the same vn_sock,same lower device and same remote_ip, the mc_list of the vn_sock should not be changed. Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-19 01:49:24 +0000