summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath10k/wmi.h
AgeCommit message (Collapse)Author
2018-01-09ath10k: fix spelling errorErik Stromdahl
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-12-27ath10k: update copyright yearKalle Valo
Update year for Qualcomm Atheros, Inc. copyrights. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-27ath10k: advertise TDLS wider bandwidth support for 5GHzBalaji Pothunoori
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities. This patch is required for chipset QCA9888. Tested with firmware version 10.4-3.5.1-00018. Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-14ath10k: wmi: add management tx by reference support over wmiRakesh Pillai
HL1.0 firmware branch, used in wcn3990, transmits management frames by reference over WMI. Add support for management tx by reference over WMI. Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-14ath10k: wmi: modify svc bitmap parsing for wcn3990Rakesh Pillai
Due to the limitation of wmi tlv parsing logic, if there are two parameters in a wmi event with same tlv tag, we can get only the last value, as it overwrites the prev value of the same tlv tag. The service ready event in wcn3990 contains two parameters of the same tag UINT32, due to which the svc bitmap is overwritten with the DBS support parameter. Refactor the service ready event parsing to allow parsing two tlv of the same tag UINT32 for wcn3990. Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-07ath10k: fix invalid STS_CAP_OFFSET_MASKBen Greear
The 10.4 firmware defines this as a 3-bit field, as does the mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF at least in the firmware header I have seen. This patch fixes the ath10k wmi header to match the firmware. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-10-13ath10k: add new cipher suite supportRajkumar Manoharan
QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and GCMP-256 ciphers in hardware, so advertise support for these. As firmware does not support group management frame ciphers (BIP), handle them in software (mac80211). Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-08-03ath10k: push peer type to target for TDLS peersManikanta Pubbisetty
WMI interface for all the firmwares(except QCA6174) does not include the type of peer(default/bss/tdls) requested during peer creation, therefore target creates a default peer. TDLS implementation on 10.4 firmware requires host to configure the peer type(tdls) for TDLS peers. This patch adds peer type parameter to the existing WMI interface for peer creation to accommodate this requirement. Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2) with ping tests for AP/STA modes. Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-08-03ath10k: add tdls support for 10.4 firmwaresManikanta Pubbisetty
This patch adds the support of TDLS feature for 10.4 firmware versions. A new WMI service is added to advertise the support of TDLS for 10.4 firmwares. Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-08-03ath10k: extend wmi service map to accommodate new servicesManikanta Pubbisetty
Though there is room to accommodate 512 services in wmi service ready event, target uses only first 4-bits of each 32-bit word for advertising wmi services thereby limiting max wmi services to 64. TDLS implementation for 10.4 firmwares introduces new wmi services by making use of remaining unused bits of each 32-bit word, therefore the wmi service mapping in host needs to be extended. This patch adds the logic to extend the wmi SVCMAP to accommodate new wmi services. Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-06-21ath10k: configure rxnss_override for QCA9984Ben Greear
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz. First, report this to user-space by setting the max-tx-speed and max-rx-speed vht capabilities. Second, if the peer rx-speed is configured, and if we are in 160 or 80+80 mode, and the peer rx-speed matches the max speed for 2x2 or 1x1 at 160Mhz (long guard interval), then use that info to set the peer_bw_rxnss_override appropriately. Without this, a 9984 firmware will not use 2x2 ratesets when transmitting to peer (it will be stuck at 1x1), because the firmware would not have configured the rxnss_override. Signed-off-by: Ben Greear <greearb@candelatech.com> [sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup] Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [kvalo@qca.qualcomm.com: use hw_params, rename the title] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: clean header files from bad block commentsMarcin Rokicki
Fix output from checkpatch.pl like: Block comments use a trailing */ on a separate line Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-03-20ath10k: fix typo in wmi header fileMohammed Shafi Shajakhan
Fix typo (spelling mistake) in wmi.h Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-03-16ath10k: update available channel list for 5G radioTamizh chelvam
If a 5 GHz radio is calibrated for operation in both the low band (channels 36 to 64) and high band(channels 100 to 169), hardware allows operations in all the listed channels. However, if the chip has been calibrated only for the low/high band and a high/low band channel is configured, due to lack of calibration there will be potentially invalid signal on those non calibrated channels. To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for those non calibrated channels by using low_5ghz_chan and high_5ghz_chan values which we get from target through wmi service ready event. Driver initialized flags are getting re initialized in handle_channel in cfg80211. So calling the function to disable the non supported channel from reg_notifier(). Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-02-14ath10k: fix commentAmadeusz Sławiński
I wanted to take a look and it's apparently in other header Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-02-07ath10k: add debugfs support to get per peer tids log via tracingMaharaja Kennadyrajan
This patch provides support to get per peer tids log. echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/ XX:XX/peer_debug_trigger These logs will be the part of FWLOGS which we collect the logs via tracing interface. Here we will get the peer tigd logs only once(not repeatedly) when we write 1 to the debugfs file. Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-02-07ath10k: use names in function definition argumentsKalle Valo
Fixes new checkpatch warnings: drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-13ath10k: add VHT160 supportSebastian Gottschall
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear R7800. 80+80 is possible, but disabled so far since it seems to contain glitches like missing vht station flags (this may be firmware or mac80211 related). Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> [kvalo@qca.qualcomm.com: refactoring and fix few warnings] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-11-23ath10k: add per peer htt tx stats support for 10.4Anilkumar Kolli
Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS' event, Firmware sends one HTT event for every four PPDUs. HTT payload has success pkts/bytes, failed pkts/bytes, retry pkts/bytes and rate info per ppdu. Peer stats are enabled through 'WMI_SERVICE_PEER_STATS', which are nowadays enabled by default. Parse peer stats and update the tx rate information per STA. tx rate, Peer stats are tested on QCA4019 with Firmware version 10.4-3.2.1-00028. Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-11-23ath10k: remove set/get_tsf ieee80211_opsPedersen, Thomas
Neither of these did the right thing: - get_tsf just returned 0 - set_tsf assumed a simple offset was applied against get_tsf(), which works, except in the case of calculating TSF from rx_mactime (actual TSF). Just remove them for now. We can reimplement set_tsf in terms of TSF increment/decrement in the future if get_tsf is ever supported by FW. Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-11-23ath10k: implement offset_tsf ieee80211_opPedersen, Thomas
Current set_tsf is implemented in terms of TSF_INCREMENT only. Instead support new WMI command TSF_DECREMENT and export these through offset_tsf. Advantage is we get more accurate TSF adjustments, and don't calculate wrong offset in case absolute TSF was calculated from rx_mactime (actual TSF). The new WMI command is available in firmware 10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new firmware or vice versa shouldn't be a problem since get/set tsf logic was already broken. Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-09-27ath10k: document cycle count related countersBen Greear
They are not necessarily named in an intuitive manner, so at least add some comments to help the next person. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-09-27ath10k: spelling and miscellaneous neateningJoe Perches
Correct some trivial comment typos. Remove unnecessary parentheses in a long line. Signed-off-by: Joe Perches <joe@perches.com> [kvalo@qca.qualcomm.com: drop the change for return] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-09-02ath10k: Added support for extended dbglog module id for 10.4Maharaja Kennadyrajan
For 10.4 fw versions, dbglog module id has been extended from u32 to u64, hence this patch fixes the same in the ath10k driver side. This patch doesn't break the older 10.4 releases. The FW change is already present in the older FWs. Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-09-02ath10k: Add WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT wmi serviceTamizh chelvam
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in the commit 7e247a9e88dc ("ath10k: add dynamic tx mode switch config support for qca4019"). This patch adds the service to avoid mismatch between host and target. Fixes: 7e247a9e88dc ("ath10k: add dynamic tx mode switch config support for qca4019") Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-08-31ath10k: add wmi command barrier utilityMichal Kazior
This allows placing command barriers for explicit serializing and synchronizing state. Useful for future driver development. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-08-31ath10k: implement wmi echo eventMichal Kazior
Will be useful for implementing command barriers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08ath10k: fix 10.4 extended peer stats updateMohammed Shafi Shajakhan
10.4 'extended peer stats' will be not be appended with normal peer stats data and they shall be coming in separate chunks. Fix this by maintaining a separate linked list 'extender peer stats' for 10.4 and update rx_duration for per station statistics. Also parse through beacon filter (if enabled), to make sure we parse the extended peer stats properly. This issue was exposed when more than one client is connected and extended peer stats for 10.4 is enabled The order for the stats is as below S - standard peer stats, E- extended peer stats, B - beacon filter stats {S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..} Fixes: f9575793d44c ("ath10k: enable parsing per station rx duration for 10.4") Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-02ath10k: add pdev param support to enable/disable btcoexRajkumar Manoharan
10.4 firmware has support to enable or disable btcoex functionality without reloading firmware via wmi pdev param. Add provision to send pdev param command via existing btcoex knob. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-05-06ath10k: handle pdev_chan_info wmi eventRajkumar Manoharan
Add handler to process bss channel information wmi event that will be received upon sending pdev_chan_info_request wmi command. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-05-06ath10k: implement wmi_pdev_bss_chan_info_requestRajkumar Manoharan
Add WMI ops to send pdev_bss_chan_info_request command to target. This command will be used to retrieve updated cycle counters and noise floor value of current operating channel (bss channel). Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-05-06ath10k: add pdev bss channel info wmi definitionsRajkumar Manoharan
Add WMI definitions for pdev bss channel information request and event. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-26ath10k: add max_tx_power for QCA6174 WLAN.RM.2.0 firmwareAlan Liu
QCA6174 WLAN.RM.2.0 firmware uses max_tx_power instead of using max_reg_power to set transmission power. The tx power was about -50dbm, after applying this change, it become -32dbm. Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-19ath10k: add dynamic tx mode switch config support for qca4019Raja Mani
push-pull mode needs certain amount the host driver involvement for managing queues in the host memory and packet delivery to firmware. qca4019 wifi firmware has an option to stay in push mode for less number of active traffic flow and then switch to push-pull mode when the active traffic flow goes beyond the certain limit. The advantage of staying in push mode for less active traffic is, the host cpu consumption is reduced. qca4019 firmware supports this flexibility of the mode switch. It takes the host driver interest (LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID, LOW_PERF - fw would stay in push mode and switch to push-pull based on demand. HIGH_PERF - fw would stay in push-pull mode from the boot. To make this configuration generic, new WMI services WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL, WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode switch support availability in firmware. Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is configured to the firmware. Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-14ath10k: fix checkpatch warnings related to spacesKalle Valo
Fix checkpatch warnings about use of spaces with operators: spaces preferred around that '*' (ctx:VxV) This has been recently added to checkpatch. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-12ath10k: update 10.4 WMI vdev parametersPeter Oh
Update 10.4 WMI vdev param to sync to current 10.4 firmware as of 2/23/2016. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-12ath10k: add a support of set_tsf on vdev interfacePeter Oh
10.2.4.70.24 firmware introduces new feature to set TSF via vdev parameter, hence implement relevant function. set_tsf function can be used to shift TBTT that will help avoid its clockdrift which happens when beacons are collided. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-12ath10k: Document alloc_frag_desc_for_data_pkt config option.Ben Greear
This will help anyone trying to use the ack-rssi reporting feature with the host-specified TX-rate option in 10.4 firmware. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-04ath10k: enable parsing per station rx duration for 10.4Mohammed Shafi Shajakhan
Rx duration support for per station is part of extended peer stats, enable provision to parse the same and provide backward compatibility based on the 'stats_id' event Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-04ath10k: introduce Extended Resource Config support for 10.4Raja Mani
Add API support for Extended Resource Configuration for 10.4. This is useful to enable new features like Peer Stats, LTEU etc if the firmware advertises support for the service. This is also done to provide backward compatibility with older firmware. Also for clarity send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF', though this should not make any difference in functionality Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-03-08ath10k: set MAC timestamp in management Rx framePeter Oh
Check and set Rx MAC timestamp when firmware indicates it. Firmware adds it in Rx beacon frame only at this moment. Driver and mac80211 may utilize it to detect such clockdrift or beacon collision and use the result for beacon collision avoidance. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-02-02ath10k: populate qca4019 fw specific wmi init paramsRaja Mani
Some of the parameter like tx/rx chain mask, number of htt tx desc, qcache active peer count, etc goes via wmi init cmd to qca4019 firmware are different. To make use of 10.4 gen_init function for qca4019, change wmi service ready handler and 10.4 wmi init functions to adapt qca4019 specific init values. Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-02-02ath10k: add abstraction layer for vdev subtypePeter Oh
Abstraction layer for vdev subtype is added to solve subtype mismatch and to give flexible compatibility among different firmware revisions. For instance, 10.2 and 10.4 firmware has different definition of their vdev subtypes for Mesh. 10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5. Hence use the abstraction API to get right subtype to use. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-02-02ath10k: update 10.4 WMI service mapPeter Oh
Update 10.4 WMI service map to sync to the latest 10.4 firmware as of 1/20/2016. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-02-02ath10k: rename Mesh related service namesPeter Oh
WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh. Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S. Also add _11S as post-fix to each of WMI_SERVICE_MESH and WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh. This will help users to distinguish 11s Mesh from non 11s Mesh. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-01-26ath10k: remove the p2p notice of absence info from 10.2.4 FW beacon infoYanbo Li
The p2p NOA never been supported at 10.2.4 FW, remove it to avoid SWBA event parse error for multi beacon interval case. Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-01-26ath10k: fix naming Peer stats rssi_changed field in 10.2.4Mohammed Shafi Shajakhan
Fix naming of peer stats rssi_changed field in 10.2.4 to make it more readable. As of now this field is not used, but necessary to pull in fw_stats with appropriate length. Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-01-21ath10k: add support for parsing per STA rx_duration for 10.2.4Mohammed Shafi Shajakhan
Add support for parsing 'peer_rx_duration' as part of 10.2.4 peer_stats. Also register PEER_STATS service for parsing 'rx_duration' (and for any new fields to be added as part of peer_stats). Have checks for backward compatibility with older 10.2.4 firmware incase PEER_STATS service is not enabled Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-11-30ath10k: introduce new subtypes for proxy STA and MeshPeter Oh
QCA988X firmware starting from 10.2.4.70.12-2 supports new vdev subtypes for proxy STA and Mesh, hence add them to be used as needed. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-11-30ath10k: update WMI 10.x service mapPeter Oh
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2 released on 11/11/2015 which is the latest QCA988X firmware as of 11/18/2015. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-04 16:12:57 +0000