summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2021-07-27net/mlx5e: RX, Avoid possible data corruption when relaxed ordering and LRO ↵Tariq Toukan
combined When HW aggregates packets for an LRO session, it writes the payload of two consecutive packets of a flow contiguously, so that they usually share a cacheline. The first byte of a packet's payload is written immediately after the last byte of the preceding packet. In this flow, there are two consecutive write requests to the shared cacheline: 1. Regular write for the earlier packet. 2. Read-modify-write for the following packet. In case of relaxed-ordering on, these two writes might be re-ordered. Using the end padding optimization (to avoid partial write for the last cacheline of a packet) becomes problematic if the two writes occur out-of-order, as the padding would overwrite payload that belongs to the following packet, causing data corruption. Avoid this by disabling the end padding optimization when both LRO and relaxed-ordering are enabled. Fixes: 17347d5430c4 ("net/mlx5e: Add support for PCI relaxed ordering") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-27net/mlx5: E-Switch, handle devcom events only for ports on the same deviceRoi Dayan
This is the same check as LAG mode checks if to enable lag. This will fix adding peer miss rules if lag is not supported and even an incorrect rules in socket direct mode. Also fix the incorrect comment on mlx5_get_next_phys_dev() as flow #1 doesn't exists. Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-27net/mlx5: E-Switch, Set destination vport vhca id only when merged eswitch ↵Maor Dickman
is supported Destination vport vhca id is valid flag is set only merged eswitch isn't supported. Change destination vport vhca id value to be set also only when merged eswitch is supported. Fixes: e4ad91f23f10 ("net/mlx5e: Split offloaded eswitch TC rules for port mirroring") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-27net/mlx5e: Disable Rx ntuple offload for uplink representorMaor Dickman
Rx ntuple offload is not supported in switchdev mode. Tryng to enable it cause kernel panic. BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 80000001065a5067 P4D 80000001065a5067 PUD 106594067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 7 PID: 1089 Comm: ethtool Not tainted 5.13.0-rc7_for_upstream_min_debug_2021_06_23_16_44 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_arfs_enable+0x70/0xd0 [mlx5_core] Code: 44 24 10 00 00 00 00 48 c7 44 24 18 00 00 00 00 49 63 c4 48 89 e2 44 89 e6 48 69 c0 20 08 00 00 48 89 ef 48 03 85 68 ac 00 00 <48> 8b 40 08 48 89 44 24 08 e8 d2 aa fd ff 48 83 05 82 96 18 00 01 RSP: 0018:ffff8881047679e0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000004000000000 RCX: 0000004000000000 RDX: ffff8881047679e0 RSI: 0000000000000000 RDI: ffff888115100880 RBP: ffff888115100880 R08: ffffffffa00f6cb0 R09: ffff888104767a18 R10: ffff8881151000a0 R11: ffff888109479540 R12: 0000000000000000 R13: ffff888104767bb8 R14: ffff888115100000 R15: ffff8881151000a0 FS: 00007f41a64ab740(0000) GS:ffff8882f5dc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000104cbc005 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: set_feature_arfs+0x1e/0x40 [mlx5_core] mlx5e_handle_feature+0x43/0xa0 [mlx5_core] mlx5e_set_features+0x139/0x1b0 [mlx5_core] __netdev_update_features+0x2b3/0xaf0 ethnl_set_features+0x176/0x3a0 ? __nla_parse+0x22/0x30 genl_family_rcv_msg_doit+0xe2/0x140 genl_rcv_msg+0xde/0x1d0 ? features_reply_size+0xe0/0xe0 ? genl_get_cmd+0xd0/0xd0 netlink_rcv_skb+0x4e/0xf0 genl_rcv+0x24/0x40 netlink_unicast+0x1f6/0x2b0 netlink_sendmsg+0x225/0x450 sock_sendmsg+0x33/0x40 __sys_sendto+0xd4/0x120 ? __sys_recvmsg+0x4e/0x90 ? exc_page_fault+0x219/0x740 __x64_sys_sendto+0x25/0x30 do_syscall_64+0x3f/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f41a65b0cba Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c RSP: 002b:00007ffd8d688358 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000010f42a0 RCX: 00007f41a65b0cba RDX: 0000000000000058 RSI: 00000000010f43b0 RDI: 0000000000000003 RBP: 000000000047ae60 R08: 00007f41a667c000 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 00000000010f4340 R13: 00000000010f4350 R14: 00007ffd8d688400 R15: 00000000010f42a0 Modules linked in: mlx5_vdpa vhost_iotlb vdpa xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad ib_ipoib rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core overlay mlx5_core ptp pps_core fuse CR2: 0000000000000008 ---[ end trace c66523f2aba94b43 ]--- Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-27net/mlx5: Fix flow table chainingMaor Gottlieb
Fix a bug when flow table is created in priority that already has other flow tables as shown in the below diagram. If the new flow table (FT-B) has the lowest level in the priority, we need to connect the flow tables from the previous priority (p0) to this new table. In addition when this flow table is destroyed (FT-B), we need to connect the flow tables from the previous priority (p0) to the next level flow table (FT-C) in the same priority of the destroyed table (if exists). --------- |root_ns| --------- | -------------------------------- | | | ---------- ---------- --------- |p(prio)-x| | p-y | | p-n | ---------- ---------- --------- | | ---------------- ------------------ |ns(e.g bypass)| |ns(e.g. kernel) | ---------------- ------------------ | | | ------- ------ ---- | p0 | | p1 | |p2| ------- ------ ---- | | \ -------- ------- ------ | FT-A | |FT-B | |FT-C| -------- ------- ------ Fixes: f90edfd279f3 ("net/mlx5_core: Connect flow tables") Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-27net: hns3: change the method of obtaining default ptp cycleYufeng Mo
The ptp cycle is related to the hardware, so it may cause compatibility issues if a fixed value is used in driver. Therefore, the method of obtaining this value is changed to read from the register rather than use a fixed value in driver. Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27octeontx2-af: Do NIX_RX_SW_SYNC twiceSunil Goutham
NIX_RX_SW_SYNC ensures all existing transactions are finished and pkts are written to LLC/DRAM, queues should be teared down after successful SW_SYNC. Due to a HW errata, in some rare scenarios an existing transaction might end after SW_SYNC operation. To ensure operation is fully done, do the SW_SYNC twice. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-26bnxt_en: Fix static checker warning in bnxt_fw_reset_task()Somnath Kotur
Now that we return when bnxt_open() fails in bnxt_fw_reset_task(), there is no need to check for 'rc' value again before invoking bnxt_reenable_sriov(). Fixes: 3958b1da725a ("bnxt_en: fix error path of FW reset") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-26net/qla3xxx: fix schedule while atomic in ql_wait_for_drvr_lock and ↵Letu Ren
ql_adapter_reset When calling the 'ql_wait_for_drvr_lock' and 'ql_adapter_reset', the driver has already acquired the spin lock, so the driver should not call 'ssleep' in atomic context. This bug can be fixed by using 'mdelay' instead of 'ssleep'. Reported-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-26net: stmmac: add est_irq_status callback function for GMAC 4.10 and 5.10Mohammad Athari Bin Ismail
Assign dwmac5_est_irq_status to est_irq_status callback function for GMAC 4.10 and 5.10. With this, EST related interrupts could be handled properly. Fixes: e49aa315cb01 ("net: stmmac: EST interrupts handling and error reporting") Cc: <stable@vger.kernel.org> # 5.13.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Acked-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25net: qede: Fix end of loop tests for list_for_each_entryHarshvardhan Jha
The list_for_each_entry() iterator, "vlan" in this code, can never be NULL so the warning will never be printed. Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25mlx4: Fix missing error code in mlx4_load_one()Jiapeng Chong
The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'err'. Eliminate the follow smatch warning: drivers/net/ethernet/mellanox/mlx4/main.c:3538 mlx4_load_one() warn: missing error code 'err'. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: 7ae0e400cd93 ("net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs") Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25net: phy: broadcom: re-add check for PHY_BRCM_DIS_TXCRXC_NOENRGY on the ↵Kevin Lo
BCM54811 PHY Restore PHY_ID_BCM54811 accidently removed by commit 5d4358ede8eb. Fixes: 5d4358ede8eb ("net: phy: broadcom: Allow BCM54210E to configure APD") Signed-off-by: Kevin Lo <kevlo@kevlo.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25octeontx2-pf: Dont enable backpressure on LBK linksHariprasad Kelam
Avoid configure backpressure for LBK links as they don't support it and enable lmacs before configuration pause frames. Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25octeontx2-pf: Fix interface down flag on errorGeetha sowjanya
In the existing code while changing the number of TX/RX queues using ethtool the PF/VF interface resources are freed and reallocated (otx2_stop and otx2_open is called) if the device is in running state. If any resource allocation fails in otx2_open, driver free already allocated resources and return. But again, when the number of queues changes as the device state still running oxt2_stop is called. In which we try to free already freed resources leading to driver crash. This patch fixes the issue by setting the INTF_DOWN flag on error and free the resources in otx2_stop only if the flag is not set. Fixes: 50fe6c02e5ad ("octeontx2-pf: Register and handle link notifications") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-25octeontx2-af: Fix PKIND overlap between LBK and LMAC interfacesGeetha sowjanya
Currently PKINDs are not assigned to LBK channels. The default value of LBK_CHX_PKIND (channel to PKIND mapping) register is zero, which is resulting in a overlap of pkind between LBK and CGX LMACs. When KPU1 parser config is modified when PTP timestamping is enabled on the CGX LMAC interface it is impacting traffic on LBK interfaces as well. This patch fixes the issue by reserving the PKIND#0 for LBK devices. CGX mapped PF pkind starts from 1 and also fixes the max pkind available. Fixes: 421572175ba5 ("octeontx2-af: Support to enable/disable HW timestamping") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-24bnxt_en: Add missing periodic PHC overflow checkMichael Chan
We use the timecounter APIs for the 48-bit PHC and packet timestamps. We must periodically update the timecounter at roughly half the overflow interval. The overflow interval is about 78 hours, so update it every 19 hours (1/4 interval) for some extra margins. Fixes: 390862f45c85 ("bnxt_en: Get the full 48-bit hardware timestamp periodically") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-24can: mcp251xfd: mcp251xfd_irq(): stop timestamping worker in case error in IRQMarc Kleine-Budde
In case an error occurred in the IRQ handler, the chip status is dumped via devcoredump and all IRQs are disabled, but the chip stays powered for further analysis. The chip is in an undefined state and will not receive any CAN frames, so shut down the timestamping worker, which reads the TBC register regularly, too. This avoids any CRC read error messages if there is a communication problem with the chip. Fixes: efd8d98dfb90 ("can: mcp251xfd: add HW timestamp infrastructure") Link: https://lore.kernel.org/r/20210724155131.471303-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-07-24can: peak_usb: pcan_usb_handle_bus_evt(): fix reading rxerr/txerr valuesStephane Grosjean
This patch fixes an incorrect way of reading error counters in messages received for this purpose from the PCAN-USB interface. These messages inform about the increase or decrease of the error counters, whose values are placed in bytes 1 and 2 of the message data (not 0 and 1). Fixes: ea8b33bde76c ("can: pcan_usb: add support of rxerr/txerr counters") Link: https://lore.kernel.org/r/20210625130931.27438-4-s.grosjean@peak-system.com Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-07-23ionic: count csum_none when offload enabledShannon Nelson
Be sure to count the csum_none cases when csum offload is enabled. Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23ionic: fix up dim accounting for tx and rxShannon Nelson
We need to count the correct Tx and/or Rx packets for dynamic interrupt moderation, depending on which we're processing on the queue interrupt. Fixes: 04a834592bf5 ("ionic: dynamic interrupt moderation") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23ionic: remove intr coalesce update from napiShannon Nelson
Move the interrupt coalesce value update out of the napi thread and into the dim_work thread and set it only when it has actually changed. Fixes: 04a834592bf5 ("ionic: dynamic interrupt moderation") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23ionic: catch no ptp support earlierShannon Nelson
If PTP configuration is attempted on ports that don't support it, such as VF ports, the driver will return an error status -95, or EOPNOSUPP and print an error message enp98s0: hwstamp set failed: -95 Because some daemons can retry every few seconds, this can end up filling the dmesg log and pushing out other more useful messages. We can catch this issue earlier in our handling and return the error without a log message. Fixes: 829600ce5e4e ("ionic: add ts_config replay") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23ionic: make all rx_mode work threadsafeShannon Nelson
Move the bulk of the code from ionic_set_rx_mode(), which can be called from atomic context, into ionic_lif_rx_mode() which is a safe context. A call from the stack will get pushed off into a work thread, but it is also possible to simultaneously have a call driven by a queue reconfig request from an ethtool command or fw recovery event. We add a mutex around the rx_mode work to be sure they don't collide. Fixes: 81dbc24147f9 ("ionic: change set_rx_mode from_ndo to can_sleep") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23Merge branch '40GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-07-23 This series contains updates to i40e driver only. Arkadiusz corrects the order of calls for disabling queues to resolve a false error message and adds a better message to the user when transitioning FW LLDP back on while the firmware is still processing the off request. Lukasz adds additional information regarding possible incorrect cable use when a PHY type error occurs. Jedrzej adds ndo_select_queue support to resolve incorrect queue selection when SW DCB is used and adds a warning when there are not enough queues for desired TC configuration. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23Merge tag 'mac80211-for-net-2021-07-23' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Couple of fixes: * fix aggregation on mesh * fix late enabling of 4-addr mode * leave monitor SKBs with some headroom * limit band information for old applications * fix virt-wifi WARN_ON * fix memory leak in cfg80211 BSS list maintenance
2021-07-23NIU: fix incorrect error return, missed in previous revertPaul Jakma
Commit 7930742d6, reverting 26fd962, missed out on reverting an incorrect change to a return value. The niu_pci_vpd_scan_props(..) == 1 case appears to be a normal path - treating it as an error and return -EINVAL was breaking VPD_SCAN and causing the driver to fail to load. Fix, so my Neptune card works again. Cc: Kangjie Lu <kjlu@umn.edu> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Fixes: 7930742d ('Revert "niu: fix missing checks of niu_pci_eeprom_read"') Signed-off-by: Paul Jakma <paul@jakma.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23octeontx2-af: Fix uninitialized variables in rvu_switchSubbaraya Sundeep
Get the number of VFs of a PF correctly by calling rvu_get_pf_numvfs in rvu_switch_disable function. Also hwvf is not required hence remove it. Fixes: 23109f8dd06d ("octeontx2-af: Introduce internal packet switching") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23wwan: core: Fix missing RTM_NEWLINK event for default linkLoic Poulain
A wwan link created via the wwan_create_default_link procedure is never notified to the user (RTM_NEWLINK), causing issues with user tools relying on such event to track network links (NetworkManager). This is because the procedure misses a call to rtnl_configure_link(), which sets the link as initialized and notifies the new link (cf proper usage in __rtnl_newlink()). Cc: stable@vger.kernel.org Fixes: ca374290aaad ("wwan: core: support default netdev creation") Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23net: dsa: mv88e6xxx: silently accept the deletion of VID 0 tooVladimir Oltean
The blamed commit modified the driver to accept the addition of VID 0 without doing anything, but deleting that VID still fails: [ 32.080780] mv88e6085 d0032004.mdio-mii:10 lan8: failed to kill vid 0081/0 Modify mv88e6xxx_port_vlan_leave() to do the same thing as the addition. Fixes: b8b79c414eca ("net: dsa: mv88e6xxx: Fix adding vlan 0") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23octeontx2-af: Remove unnecessary devm_kfreeSunil Goutham
Remove devm_kfree of memory where VLAN entry to RVU PF mapping info is saved. This will be freed anyway at driver exit. Having this could result in warning from devm_kfree() if the memory is not allocated due to errors in rvu_nix_block_init() before nix_setup_txvlan(). Fixes: 9a946def264d ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries") Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23i40e: Fix log TC creation failure when max num of queues is exceededJedrzej Jagielski
Fix missing failed message if driver does not have enough queues to complete TC command. Without this fix no message is displayed in dmesg. Fixes: a9ce82f744dc ("i40e: Enable 'channel' mode in mqprio for TC configs") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23i40e: Fix queue-to-TC mapping on TxJedrzej Jagielski
In SW DCB mode the packets sent receive incorrect UP tags. They are constructed correctly and put into tx_ring, but UP is later remapped by HW on the basis of TCTUPR register contents according to Tx queue selected, and BW used is consistent with the new UP values. This is caused by Tx queue selection in kernel not taking into account DCB configuration. This patch fixes the issue by implementing the ndo_select_queue NDO callback. Fixes: fd0a05ce74ef ("i40e: transmit, receive, and NAPI") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23i40e: Add additional info to PHY type errorLukasz Cieplicki
In case of PHY type error occurs, the message was too generic. Add additional info to PHY type error indicating that it can be wrong cable connected. Fixes: 124ed15bf126 ("i40e: Add dual speed module support") Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com> Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23i40e: Fix firmware LLDP agent related warningArkadiusz Kubalewski
Make warning meaningful for the user. Previously the trace: "Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN" was produced when user tried to start Firmware LLDP agent, just after it was stopped with sequence: ethtool --set-priv-flags <dev> disable-fw-lldp on ethtool --set-priv-flags <dev> disable-fw-lldp off (without any delay between the commands) At that point the firmware is still processing stop command, the behavior is expected. Fixes: c1041d070437 ("i40e: Missing response checks in driver when starting/stopping FW LLDP") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23i40e: Fix logic of disabling queuesArkadiusz Kubalewski
Correct the message flow between driver and firmware when disabling queues. Previously in case of PF reset (due to required reinit after reconfig), the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up occasionally. The error was not a real issue of hardware or firmware, it was caused by wrong sequence of messages invoked by the driver. Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23virt_wifi: fix error on connectMatteo Croce
When connecting without first doing a scan, the BSS list is empty and __cfg80211_connect_result() generates this warning: $ iw dev wlan0 connect -w VirtWifi [ 15.371989] ------------[ cut here ]------------ [ 15.372179] WARNING: CPU: 0 PID: 92 at net/wireless/sme.c:756 __cfg80211_connect_result+0x402/0x440 [ 15.372383] CPU: 0 PID: 92 Comm: kworker/u2:2 Not tainted 5.13.0-kvm #444 [ 15.372512] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-3.fc34 04/01/2014 [ 15.372597] Workqueue: cfg80211 cfg80211_event_work [ 15.372756] RIP: 0010:__cfg80211_connect_result+0x402/0x440 [ 15.372818] Code: 48 2b 04 25 28 00 00 00 75 59 48 8b 3b 48 8b 76 10 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d 49 8d 65 f0 41 5d e9 d0 d4 fd ff 0f 0b <0f> 0b e9 f6 fd ff ff e8 f2 4a b4 ff e9 ec fd ff ff 0f 0b e9 19 fd [ 15.372966] RSP: 0018:ffffc900005cbdc0 EFLAGS: 00010246 [ 15.373022] RAX: 0000000000000000 RBX: ffff8880028e2400 RCX: ffff8880028e2472 [ 15.373088] RDX: 0000000000000002 RSI: 00000000fffffe01 RDI: ffffffff815335ba [ 15.373149] RBP: ffffc900005cbe00 R08: 0000000000000008 R09: ffff888002bdf8b8 [ 15.373209] R10: ffff88803ec208f0 R11: ffffffffffffe9ae R12: ffff88801d687d98 [ 15.373280] R13: ffff88801b5fe000 R14: ffffc900005cbdc0 R15: dead000000000100 [ 15.373330] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000 [ 15.373382] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 15.373425] CR2: 000056421c468958 CR3: 000000001b458001 CR4: 0000000000170eb0 [ 15.373478] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 15.373529] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 15.373580] Call Trace: [ 15.373611] ? cfg80211_process_wdev_events+0x10e/0x170 [ 15.373743] cfg80211_process_wdev_events+0x10e/0x170 [ 15.373783] cfg80211_process_rdev_events+0x21/0x40 [ 15.373846] cfg80211_event_work+0x20/0x30 [ 15.373892] process_one_work+0x1e9/0x340 [ 15.373956] worker_thread+0x4b/0x3f0 [ 15.374017] ? process_one_work+0x340/0x340 [ 15.374053] kthread+0x11f/0x140 [ 15.374089] ? set_kthread_struct+0x30/0x30 [ 15.374153] ret_from_fork+0x1f/0x30 [ 15.374187] ---[ end trace 321ef0cb7e9c0be1 ]--- wlan0 (phy #0): connected to 00:00:00:00:00:00 Add the fake bss just before the connect so that cfg80211_get_bss() finds the virtual network. As some code was duplicated, move it in a common function. Signed-off-by: Matteo Croce <mcroce@microsoft.com> Link: https://lore.kernel.org/r/20210706154423.11065-1-mcroce@linux.microsoft.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-07-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Fix type of bind option flag in af_xdp, from Baruch Siach. 2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao. 3) PM refcnt imbakance in r8152, from Takashi Iwai. 4) Sign extension ug in liquidio, from Colin Ian King. 5) Mising range check in s390 bpf jit, from Colin Ian King. 6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan. 7) Fix skb page recycling race, from Ilias Apalodimas. 8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin. 9) netrom timer sk refcnt issues, from Nguyen Dinh Phi. 10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric Dumazet. 11) act_skbmod should only operate on ethernet packets, from Peilin Ye. 12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo Abeni. 13) Fix sparx5 dependencies, from Yajun Deng. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits) dpaa2-switch: seed the buffer pool after allocating the swp net: sched: cls_api: Fix the the wrong parameter net: sparx5: fix unmet dependencies warning net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum net: dsa: ensure linearized SKBs in case of tail taggers ravb: Remove extra TAB ravb: Fix a typo in comment net: dsa: sja1105: make VID 4095 a bridge VLAN too tcp: disable TFO blackhole logic by default sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set net: ixp46x: fix ptp build failure ibmvnic: Remove the proper scrq flush selftests: net: add ESP-in-UDP PMTU test udp: check encap socket in __udp_lib_err sctp: update active_key for asoc when old key is being replaced r8169: Avoid duplicate sysfs entry creation error ixgbe: Fix packet corruption due to missing DMA sync Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()" ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions fsl/fman: Add fibre support ...
2021-07-22dpaa2-switch: seed the buffer pool after allocating the swpIoana Ciornei
Any interraction with the buffer pool (seeding a buffer, acquire one) is made through a software portal (SWP, a DPIO object). There are circumstances where the dpaa2-switch driver probes on a DPSW before any DPIO devices have been probed. In this case, seeding of the buffer pool will lead to a panic since no SWPs are initialized. To fix this, seed the buffer pool after making sure that the software portals have been probed and are ready to be used. Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22net: sparx5: fix unmet dependencies warningRandy Dunlap
WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=y] && HAS_IOMEM [=y] Selected by [y]: - SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y] && OF [=y] Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21ravb: Remove extra TABBiju Das
Align the member description comments for struct ravb_desc by removing the extra TAB. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21ravb: Fix a typo in commentBiju Das
Fix the typo RX->TX in comment, as the code following the comment process TX and not RX. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21net: dsa: sja1105: make VID 4095 a bridge VLAN tooVladimir Oltean
This simple series of commands: ip link add br0 type bridge vlan_filtering 1 ip link set swp0 master br0 fails on sja1105 with the following error: [ 33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN [ 33.447710] sja1105 spi0.1: Invalid config, cannot upload Warning: sja1105: Failed to change VLAN Ethertype. For context, sja1105 has 3 operating modes: - SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware - SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware - SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the bridge_vlans are committed to hardware Swapping out a VLAN list and another in happens in sja1105_build_vlan_table(), which performs a delta update procedure. That function is called from a few places, notably from sja1105_vlan_filtering() which is called from the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler. The above set of 2 commands fails when run on a kernel pre-commit 8841f6e63f2c ("net: dsa: sja1105: make devlink property best_effort_vlan_filtering true by default"). So the priv->vlan_state transition that takes place is between VLAN-unaware and full VLAN filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans are swapped in. So why does it fail? Well, the bridge driver, through nbp_vlan_init(), first sets up the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then proceeds to call nbp_vlan_add for the default_pvid. So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge VLANs (yet). So we have wiped the VLAN table clean, and the low-level static config checker complains of an invalid configuration. We _will_ add the bridge VLANs using the dynamic config interface, albeit later, when nbp_vlan_add() calls us. So it is natural that it fails. So why did it ever work? Surprisingly, it looks like I only tested this configuration with 2 things set up in a particular way: - a network manager that brings all ports up - a kernel with CONFIG_VLAN_8021Q=y It is widely known that commit ad1afb003939 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net device that comes up. DSA treats these VLANs as bridge VLANs, and therefore, in my testing, the list of bridge_vlans was never empty. However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily empty, and the sja1105_static_config_reload() call from sja1105_vlan_filtering() will fail. To fix this, the simplest thing is to keep VID 4095, the one used for CPU-injected control packets since commit ed040abca4c1 ("net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic"), in the list of bridge VLANs too, not just the list of tag_8021q VLANs. This ensures that the list of bridge VLANs will never be empty. Fixes: ec5ae61076d0 ("net: dsa: sja1105: save/restore VLANs using a delta commit method") Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21net: ixp46x: fix ptp build failureArnd Bergmann
The rework of the ixp46x cpu detection left the network driver in a half broken state: drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init': drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function) 290 | (struct ixp46x_ts_regs __iomem *) IXP4XX_TIMESYNC_BASE_VIRT; | ^~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: note: each undeclared identifier is reported only once for each function it appears in drivers/net/ethernet/xscale/ptp_ixp46x.c: At top level: drivers/net/ethernet/xscale/ptp_ixp46x.c:323:1: error: data definition has no type or storage class [-Werror] 323 | module_init(ptp_ixp_init); I have patches to complete the transition for a future release, but for the moment, add the missing include statements to get it to build again. Fixes: 09aa9aabdcc4 ("soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21ibmvnic: Remove the proper scrq flushSukadev Bhattiprolu
Commit 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset") intended to remove the call to ibmvnic_tx_scrq_flush() when the ->resetting flag is true and was tested that way. But during the final rebase to net-next, the hunk got applied to a block few lines below (which happened to have the same diff context) and the wrong call to ibmvnic_tx_scrq_flush() got removed. Fix that by removing the correct ibmvnic_tx_scrq_flush() and restoring the one that was incorrectly removed. Fixes: 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset") Reported-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21r8169: Avoid duplicate sysfs entry creation errorSayanta Pattanayak
When registering the MDIO bus for a r8169 device, we use the PCI bus/device specifier as a (seemingly) unique device identifier. However the very same BDF number can be used on another PCI segment, which makes the driver fail probing: [ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003) [ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700' .... [ 27.684858] libphy: mii_bus r8169-700 failed to register [ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22 Add the segment number to the device name to make it more unique. This fixes operation on ARM N1SDP boards, with two boards connected together to form an SMP system, and all on-board devices showing up twice, just on different PCI segments. A similar issue would occur on large systems with many PCI slots and multiple RTL8169 NICs. Fixes: f1e911d5d0dfd ("r8169: add basic phylib support") Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com> [Andre: expand commit message, use pci_domain_nr()] Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-20ixgbe: Fix packet corruption due to missing DMA syncMarkus Boehme
When receiving a packet with multiple fragments, hardware may still touch the first fragment until the entire packet has been received. The driver therefore keeps the first fragment mapped for DMA until end of packet has been asserted, and delays its dma_sync call until then. The driver tries to fit multiple receive buffers on one page. When using 3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned off/build_skb is being used) on an architecture with 4K pages, the driver allocates an order 1 compound page and uses one page per receive buffer. To determine the correct offset for a delayed DMA sync of the first fragment of a multi-fragment packet, the driver then cannot just use PAGE_MASK on the DMA address but has to construct a mask based on the actual size of the backing page. Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration will always sync the first page of a compound page. With the SWIOTLB enabled this can lead to corrupted packets (zeroed out first fragment, re-used garbage from another packet) and various consequences, such as slow/stalling data transfers and connection resets. For example, testing on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled (e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle out without this patch. Cc: stable@vger.kernel.org Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path") Signed-off-by: Markus Boehme <markubo@amazon.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-20Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"Jia He
This reverts commit 6206b7981a36476f4695d661ae139f7db36a802d. That patch added additional spin_{un}lock_bh(), which was harmless but pointless. The orginal code path has guaranteed the pair of spin_{un}lock_bh(). We'd better revert it before we find the exact root cause of the bug_on mentioned in that patch. Fixes: 6206b7981a36 ("qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()") Cc: David S. Miller <davem@davemloft.net> Cc: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Jia He <justin.he@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-20fsl/fman: Add fibre supportMaxim Kochetkov
Set SUPPORTED_FIBRE to mac_dev->if_support. It allows proper usage of PHYs with optical/fiber support. Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-20mt7530 mt7530_fdb_write only set ivl bit vid larger than 1Eric Woudstra
Fixes my earlier patch which broke vlan unaware bridges. The IVL bit now only gets set for vid's larger than 1. Fixes: 11d8d98cbeef ("mt7530 fix mt7530_fdb_write vid missing ivl bit") Signed-off-by: Eric Woudstra <ericwouds@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-14 04:19:37 +0000