| Age | Commit message (Collapse) | Author |
|---|
|
commit 03b4776c408d2f4bf3a5d204e223724d154716d1 upstream.
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4c85ab11ca56da1aa59b58c80cc6a356515cc645 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=16476
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ff847ac2d3e90edd94674c28bade25ae1e6a2e49 upstream.
The MAC-PHY interconnect on 82577/82578 uses a power management feature
(called K1) which must be disabled when in 1Gbps due to a hardware issue on
these parts. The #define bit setting used to enable/disable K1 is
incorrect and can cause PHY register accesses to stop working altogether
until the next device reset. This patch sets the register correctly.
This issue is present in kernels since 2.6.32.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 36f2407fe52c55566221f8c68c8fb808abffd2f5 upstream.
Should e1000_test_msi() fail to see an msi interrupt, it attempts to
fallback to legacy INTx interrupts. But an error in the code may prevent
this from happening correctly.
Before calling e1000_test_msi_interrupt(), e1000_test_msi() disables SERR
by clearing the SERR bit from the just read PCI_COMMAND bits as it writes
them back out.
Upon return from calling e1000_test_msi_interrupt(), it re-enables SERR
by writing out the version of PCI_COMMAND it had previously read.
The problem with this is that e1000_test_msi_interrupt() calls
pci_disable_msi(), which eventually ends up in pci_intx(). And because
pci_intx() was called with enable set to 1, the INTX_DISABLE bit gets
cleared from PCI_COMMAND, which is what we want. But when we get back to
e1000_test_msi(), the INTX_DISABLE bit gets inadvertently re-set because
of the attempt by e1000_test_msi() to re-enable SERR.
The solution is to have e1000_test_msi() re-read the PCI_COMMAND bits as
part of its attempt to re-enable SERR.
During debugging/testing of this issue I found that not all the systems
I ran on had the SERR bit set to begin with. And on some of the systems
the same could be said for the INTX_DISABLE bit. Needless to say these
latter systems didn't have a problem falling back to legacy INTx
interrupts with the code as is.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b6855772f4a22c4fbdd4fcaceff5c8a527035123 upstream.
ath5k assumes ah_current_channel is always a valid pointer in
several places, but a newly created interface may not have a
channel. To avoid null pointer dereferences, set it up to point
to the first available channel until later reconfigured.
This fixes the following oops:
$ rmmod ath5k
$ insmod ath5k
$ iw phy0 set distance 11000
BUG: unable to handle kernel NULL pointer dereference at 00000006
IP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
*pde = 00000000
Oops: 0000 [#1]
last sysfs file: /sys/devices/pci0000:00/0000:00:0e.0/ieee80211/phy0/index
Modules linked in: usbhid option usb_storage usbserial usblp evdev lm90
scx200_acb i2c_algo_bit i2c_dev i2c_core via_rhine ohci_hcd ne2k_pci
8390 leds_alix2 xt_IMQ imq nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_cc
Pid: 1597, comm: iw Not tainted (2.6.32.14 #8)
EIP: 0060:[<d0a1ff24>] EFLAGS: 00010296 CPU: 0
EIP is at ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
EAX: 000000c2 EBX: 00000000 ECX: ffffffff EDX: c12d2080
ESI: 00000019 EDI: cf8c0000 EBP: d0a30edc ESP: cfa09bf4
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process iw (pid: 1597, ti=cfa09000 task=cf88a000 task.ti=cfa09000)
Stack:
d0a34f35 d0a353f8 d0a30edc 000000fe cf8c0000 00000000 1900063d cfa8c9e0
<0> cfa8c9e8 cfa8c0c0 cfa8c000 d0a27f0c 199d84b4 cfa8c200 00000010 d09bfdc7
<0> 00000000 00000000 ffffffff d08e0d28 cf9263c0 00000001 cfa09cc4 00000000
Call Trace:
[<d0a27f0c>] ? ath5k_hw_attach+0xc8c/0x3c10 [ath5k]
[<d09bfdc7>] ? __ieee80211_request_smps+0x1347/0x1580 [mac80211]
[<d08e0d28>] ? nl80211_send_scan_start+0x7b8/0x4520 [cfg80211]
[<c10f5db9>] ? nla_parse+0x59/0xc0
[<c11ca8d9>] ? genl_rcv_msg+0x169/0x1a0
[<c11ca770>] ? genl_rcv_msg+0x0/0x1a0
[<c11c7e68>] ? netlink_rcv_skb+0x38/0x90
[<c11c9649>] ? genl_rcv+0x19/0x30
[<c11c7c03>] ? netlink_unicast+0x1b3/0x220
[<c11c893e>] ? netlink_sendmsg+0x26e/0x290
[<c11a409e>] ? sock_sendmsg+0xbe/0xf0
[<c1032780>] ? autoremove_wake_function+0x0/0x50
[<c104d846>] ? __alloc_pages_nodemask+0x106/0x530
[<c1074933>] ? do_lookup+0x53/0x1b0
[<c10766f9>] ? __link_path_walk+0x9b9/0x9e0
[<c11acab0>] ? verify_iovec+0x50/0x90
[<c11a42b1>] ? sys_sendmsg+0x1e1/0x270
[<c1048e50>] ? find_get_page+0x10/0x50
[<c104a96f>] ? filemap_fault+0x5f/0x370
[<c1059159>] ? __do_fault+0x319/0x370
[<c11a55b4>] ? sys_socketcall+0x244/0x290
[<c101962c>] ? do_page_fault+0x1ec/0x270
[<c1019440>] ? do_page_fault+0x0/0x270
[<c1002ae5>] ? syscall_call+0x7/0xb
Code: 00 b8 fe 00 00 00 b9 f8 53 a3 d0 89 5c 24 14 89 7c 24 10 89 44 24
0c 89 6c 24 08 89 4c 24 04 c7 04 24 35 4f a3 d0 e8 7c 30 60 f0 <0f> b7
43 06 ba 06 00 00 00 a8 10 75 0e 83 e0 20 83 f8 01 19 d2
EIP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] SS:ESP
0068:cfa09bf4
CR2: 0000000000000006
---[ end trace 54f73d6b10ceb87b ]---
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b561e8274f75831ee87e4ea378cbb1f9f050a51a upstream.
The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.
And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9441cad99b4b09d6b627351c2d282833868c116c upstream.
I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee8c800923ae7918c231532a9256233eed.
Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5c659322a904a7cc0265e7b183372b9bdebec6db upstream.
This is a fix for bug 572201 @ bugs.debian.org
This patch fixes the TX_LIMIT feature flag. The previous logic check
for TX_LIMIT2 also took into account a device that only had TX_LIMIT
set.
Reported-by: Stephen Mulcahu <stephen.mulcahy@deri.org>
Reported-by: Ben Huchings <ben@decadent.org.uk>
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 380fefb2ddabd4cd5f14dbe090481f0544e65078 upstream.
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in
dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and
net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by
renaming these functions to *_unlocked for the atomic context, and make the
original functions locking wrappers for use in the non-atomic context.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a64c0f6b7ec7f758c4ef445e49f479e27fa2236 upstream.
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 50900f1698f68127e54c67fdfe829e4a97b1be2b upstream.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a69b03e941abae00380fc6bc1877fb797a1b31e6 upstream.
Avoids this:
WARNING: at net/mac80211/scan.c:312 ieee80211_scan_completed+0x5f/0x1f1
[mac80211]()
Hardware name: Latitude E5400
Modules linked in: aes_x86_64 aes_generic fuse ipt_MASQUERADE iptable_nat
nf_nat rfcomm sco bridge stp llc bnep l2cap sunrpc cpufreq_ondemand
acpi_cpufreq freq_table xt_physdev ip6t_REJECT nf_conntrack_ipv6
ip6table_filter ip6_tables ipv6 kvm_intel kvm uinput arc4 ecb
snd_hda_codec_intelhdmi snd_hda_codec_idt snd_hda_intel iwlagn snd_hda_codec
snd_hwdep snd_seq snd_seq_device iwlcore snd_pcm dell_wmi sdhci_pci sdhci
iTCO_wdt tg3 dell_laptop mmc_core i2c_i801 wmi mac80211 snd_timer
iTCO_vendor_support btusb joydev dcdbas cfg80211 bluetooth snd soundcore
microcode rfkill snd_page_alloc firewire_ohci firewire_core crc_itu_t
yenta_socket rsrc_nonstatic i915 drm_kms_helper drm i2c_algo_bit i2c_core video
output [last unloaded: scsi_wait_scan]
Pid: 979, comm: iwlagn Tainted: G W 2.6.33.3-85.fc13.x86_64 #1
Call Trace:
[<ffffffff8104b558>] warn_slowpath_common+0x77/0x8f
[<ffffffff8104b57f>] warn_slowpath_null+0xf/0x11
[<ffffffffa01bb7d9>] ieee80211_scan_completed+0x5f/0x1f1 [mac80211]
[<ffffffffa02a23f0>] iwl_bg_scan_completed+0xbb/0x17a [iwlcore]
[<ffffffff81060d3d>] worker_thread+0x1a4/0x232
[<ffffffffa02a2335>] ? iwl_bg_scan_completed+0x0/0x17a [iwlcore]
[<ffffffff81064817>] ? autoremove_wake_function+0x0/0x34
[<ffffffff81060b99>] ? worker_thread+0x0/0x232
[<ffffffff810643c7>] kthread+0x7a/0x82
[<ffffffff8100a924>] kernel_thread_helper+0x4/0x10
[<ffffffff8106434d>] ? kthread+0x0/0x82
[<ffffffff8100a920>] ? kernel_thread_helper+0x0/0x10
Reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=590436
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Mihai Harpau <mishu@piatafinanciara.ro>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d6a574ff6bfb842bdb98065da053881ff527be46 upstream.
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3a37495268ab45507b4cab9d4cb18c5496ab7a10 upstream.
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Reported-by: Johan Hovold <johan.hovold@lundinova.se>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 14acdde6e527950f66c084dbf19bad6fbfcaeedc upstream.
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9637e516d16a58b13f6098cfe899e22963132be3 upstream.
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 22896639af98ebc721a94ed71fc3acf2fb4a24dc upstream.
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter. This is accomplished by letting the
alt_mac_address function to only fail on an NVM error. If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 38000a94a902e94ca8b5498f7871c6316de8957a upstream.
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ed770f01360b392564650bf1553ce723fa46afec upstream.
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 34692421bc7d6145ef383b014860f4fde10b7505 upstream.
commit 7583605b6d29f1f7f6fc505b883328089f3485ad ("ucc_geth: Fix empty
TX queue processing") fixed empty TX queue mishandling, but didn't
account another corner case: when TX queue becomes full.
Without this patch the driver will stop transmiting when TX queue
becomes full since 'bd == ugeth->txBd[txQ]' actually checks for
two things: queue empty or full.
Let's better check for NULL skb, which unambiguously signals an empty
queue.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 08b5e1c91ce95793c59a59529a362a1bcc81faae upstream.
Since commit 864fdf884e82bacbe8ca5e93bd43393a61d2e2b4 ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c02729a8 [verbose debug info unavailable]
NIP: c02729a8 LR: c02729a8 CTR: c01b6088
REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e)
[...]
NIP [c02729a8] dev_watchdog+0x280/0x290
LR [c02729a8] dev_watchdog+0x280/0x290
Call Trace:
[c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
[c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
[c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
[c0451df0] [c00065cc] do_softirq+0xa0/0xac
[c0451e00] [c003280c] irq_exit+0x7c/0x9c
[c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
[...]
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7583605b6d29f1f7f6fc505b883328089f3485ad upstream.
Following oops was seen with the ucc_geth driver:
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3feec9095d12e311b7d4eb7fe7e5dfa75d4a72a5 upstream.
When transmitting L2TP frames, we derive the outgoing interface's UDP
checksum hardware assist capabilities from the tunnel dst dev. This
can sometimes be NULL, especially when routing protocols are used and
routing changes occur. This patch just checks for NULL dst or dev
pointers when checking for netdev hardware assist features.
BUG: unable to handle kernel NULL pointer dereference at 0000000c
IP: [<f89d074c>] pppol2tp_xmit+0x341/0x4da [pppol2tp]
*pde = 00000000
Oops: 0000 [#1] SMP
last sysfs file: /sys/class/net/lo/operstate
Modules linked in: pppol2tp pppox ppp_generic slhc ipv6 dummy loop snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_pcm snd_timer snd soundcore snd_page_alloc evdev psmouse serio_raw processor button i2c_piix4 i2c_core ati_agp agpgart pcspkr ext3 jbd mbcache sd_mod ide_pci_generic atiixp ide_core ahci ata_generic floppy ehci_hcd ohci_hcd libata e1000e scsi_mod usbcore nls_base thermal fan thermal_sys [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Not tainted (2.6.32.8 #1)
EIP: 0060:[<f89d074c>] EFLAGS: 00010297 CPU: 3
EIP is at pppol2tp_xmit+0x341/0x4da [pppol2tp]
EAX: 00000000 EBX: f64d1680 ECX: 000005b9 EDX: 00000000
ESI: f6b91850 EDI: f64d16ac EBP: f6a0c4c0 ESP: f70a9cac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=f70a8000 task=f70a31c0 task.ti=f70a8000)
Stack:
000005a9 000005b9 f734c400 f66652c0 f7352e00 f67dc800 00000000 f6b91800
<0> 000005a3 f70ef6c4 f67dcda9 000005a3 f89b192e 00000246 000005a3 f64d1680
<0> f63633e0 f6363320 f64d1680 f65a7320 f65a7364 f65856c0 f64d1680 f679f02f
Call Trace:
[<f89b192e>] ? ppp_push+0x459/0x50e [ppp_generic]
[<f89b217f>] ? ppp_xmit_process+0x3b6/0x430 [ppp_generic]
[<f89b2306>] ? ppp_start_xmit+0x10d/0x120 [ppp_generic]
[<c11c15cb>] ? dev_hard_start_xmit+0x21f/0x2b2
[<c11d0947>] ? sch_direct_xmit+0x48/0x10e
[<c11c19a0>] ? dev_queue_xmit+0x263/0x3a6
[<c11e2a9f>] ? ip_finish_output+0x1f7/0x221
[<c11df682>] ? ip_forward_finish+0x2e/0x30
[<c11de645>] ? ip_rcv_finish+0x295/0x2a9
[<c11c0b19>] ? netif_receive_skb+0x3e9/0x404
[<f814b791>] ? e1000_clean_rx_irq+0x253/0x2fc [e1000e]
[<f814cb7a>] ? e1000_clean+0x63/0x1fc [e1000e]
[<c1047eff>] ? sched_clock_local+0x15/0x11b
[<c11c1095>] ? net_rx_action+0x96/0x195
[<c1035750>] ? __do_softirq+0xaa/0x151
[<c1035828>] ? do_softirq+0x31/0x3c
[<c10358fe>] ? irq_exit+0x26/0x58
[<c1004b21>] ? do_IRQ+0x78/0x89
[<c1003729>] ? common_interrupt+0x29/0x30
[<c101ac28>] ? native_safe_halt+0x2/0x3
[<c1008c54>] ? default_idle+0x55/0x75
[<c1009045>] ? c1e_idle+0xd2/0xd5
[<c100233c>] ? cpu_idle+0x46/0x62
Code: 8d 45 08 f0 ff 45 08 89 6b 08 c7 43 68 7e fb 9c f8 8a 45 24 83 e0 0c 3c 04 75 09 80 63 64 f3 e9 b4 00 00 00 8b 43 18 8b 4c 24 04 <8b> 40 0c 8d 79 11 f6 40 44 0e 8a 43 64 75 51 6a 00 8b 4c 24 08
EIP: [<f89d074c>] pppol2tp_xmit+0x341/0x4da [pppol2tp] SS:ESP 0068:f70a9cac
CR2: 000000000000000c
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aa679c36756003f1fabdb9fc6f00eb159559f7c3 upstream.
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ac592574a577162183b5c1dd040a188caa068a29 upstream.
Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.
Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3d79b2a9eeaa066b35c49fbb17e3156a3c482c3e upstream.
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
The BUG_ON was introduced by:
commit 3110bef78cb4282c58245bc8fd6d95d9ccb19749
Author: Guy Cohen <guy.cohen@intel.com>
Date: Tue Sep 9 10:54:54 2008 +0800
iwlwifi: Added support for 3 antennas
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 45d427001b5eec03cecaacddb53c73af46bb263e upstream.
Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5ffaf8a361b4c9025963959a744f21d8173c7669 upstream.
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
802.11n but ath9k can still support them. These are called
AR2427.
[bwh: backported to 2.6.32]
Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz>
Tested-by: Bernhard Reiter <ockham@raz.or.at>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4d907069bc1b745f4abd4745c332d33098e733b8 upstream.
The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver). There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids. However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 35bb5cadc8c7b1462df57e32e08d964f1be7a75c upstream.
velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers(). I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.
On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers(). I'm not sure whether this is unsafe but
it does look wrong.
Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ac936929092dc6a5409b627c4c67305ab9b626b3 upstream.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0f666a08901f8b01f294ca0ad751019375240ae3 upstream.
Add Dell WLA3310 USB wireless card, which has a Z-Com XG-705A chipset, to the
USB Ids in p54usb.
Signed-off-by: Jason Dravet <dravet@hotmail.com>
Tested-by: Richard Gregory Tillmore <rtillmore@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6b5dcccb495b66b3b0b9581cdccfed038e5d68a2 upstream.
Commit 56d1de0a21db28e41741cfa0a66e18bc8d920554, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c0dc72bad9cf21071f5e4005de46f7c8b67a138a upstream.
If the number of sg entries in the ICM chunk reaches MLX4_ICM_CHUNK_LEN,
we must set chunk to NULL even for coherent mappings so that the next
time through the loop will allocate another chunk. Otherwise we'll
overflow the sg list the next time through the loop. This will lead to
memory corruption if this case is hit.
mthca does not have this bug.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 39d321577405e8e269fd238b278aaf2425fa788a upstream.
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Bruce Rogers <brogers@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 57c8a456640fa3ca777652f11f2db4179a3e66b6 upstream.
The SJA1000 command register is concurrently written in the rx-path to free
the receive buffer _and_ in the tx-path to start the transmission.
The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states:
"Between two commands at least one internal clock cycle is needed in
order to proceed. The internal clock is half of the external oscillator
frequency."
On SMP systems the current implementation leads to a write stall in the
tx-path, which can be solved by adding some general locking and some time
to settle the write_reg() operation for the command register.
Thanks to Klaus Hitschler for the original fix and detailed problem
description.
This patch applies on net-2.6 and (with some offsets) on net-next-2.6 .
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 879999cec9489f8942ebce3ec1b5f23ef948dda7 upstream.
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591
Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 94d0bbe849190255b93fede8eb46809a38f9b8bf upstream.
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d989ff7cf8d14f1b523f63ba0bf2ec1a9b7c25bc upstream.
When reporting Tx status, indicate that only one rate was used.
Otherwise, the rate is frozen at rate index 0 (i.e. 1Mb/s).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e7971c80a8e0299f91272ad8e8ac4167623e1862 upstream.
The SH SOHARD ARCNET cards are implemented using generic PLX Technology
PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified,
causing the driver to attach to any such bridge and likely crash the
system by attempting to initialize an unrelated device.
Fix by specifying subvendor and subdevice according to the values found
in the PCI-ID Repository at http://pci-ids.ucw.cz/ .
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fdd3d631cddad20ad9d3e1eb7dbf26825a8a121f upstream.
a developer had complained of getting lots of warnings:
"eth16 selects TX queue 98, but real number of TX queues is 64"
http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html
As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Johannes' patch 34e8950 titled:
mac80211: allow station add/remove to sleep
changed the way mac80211 adds and removes peers. The new
sta_add() / sta_remove() callbacks allowed the driver callbacks
to sleep. Johannes also ported ath9k to use sta_add() / sta_remove()
via the patch 4ca7786 titled:
ath9k: convert to new station add/remove callbacks
but this patch forgot to address a change in locking issue which
Ming Lei eventually found on his 2.6.33-wl #12 build. The 2.6.33-wl
build includes code for the 802.11 subsystem for 2.6.34 though so did
already have the above two patches (ath9k_sta_remove() on his trace),
the 2.6.33 kernel did not however have these two patches. Ming eventually
cured his lockdep warnign via the patch a9f042c titled:
ath9k: fix lockdep warning when unloading module
This went in to 2.6.34 and although it was not marked as a stable
fix it did get trickled down and applied on both 2.6.33 and 2.6.32.
In review, the culprits:
mac80211: allow station add/remove to sleep
git describe --contains 34e895075e21be3e21e71d6317440d1ee7969ad0
v2.6.34-rc1~233^2~49^2~107
ath9k: convert to new station add/remove callbacks
git describe --contains 4ca778605cfec53d8a689f0b57babb93b030c784
v2.6.34-rc1~233^2~49^2~10
ath9k: fix lockdep warning when unloading module
This last one trickled down to 2.6.33 (OK), 2.6.33 (invalid) and 2.6.32 (invalid).
git describe --contains a9f042cbe5284f34ccff15f3084477e11b39b17b
v2.6.34-rc2~48^2~77^2~7
git describe --contains 0524bcfa80f1fffb4e1fe18a0a28900869a58a7c
v2.6.33.2~125
git describe --contains 0dcc9985f34aef3c60bffab3dfc7f7ba3748f35a
v2.6.32.11~79
The patch titled "ath9k: fix lockdep warning when unloading module"
should be reverted on both 2.6.33 and 2.6.32 as it is invalid and
actually ended up causing the following warning:
ADDRCONF(NETDEV_CHANGE): wlan31: link becomes ready
phy0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 txop=0
phy0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 txop=0
phy0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 txop=94
phy0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 txop=47
phy0: device now idle
------------[ cut here ]------------
WARNING: at kernel/softirq.c:143 local_bh_enable_ip+0x7b/0xa0()
Hardware name: 7660A14
Modules linked in: ath9k(-) mac80211 ath cfg80211 <whatever-bleh-etc>
Pid: 2003, comm: rmmod Not tainted 2.6.32.11 #6
Call Trace:
[<ffffffff8105d178>] warn_slowpath_common+0x78/0xb0
[<ffffffff8105d1bf>] warn_slowpath_null+0xf/0x20
[<ffffffff81063f8b>] local_bh_enable_ip+0x7b/0xa0
[<ffffffff815121e4>] _spin_unlock_bh+0x14/0x20
[<ffffffffa034aea5>] ath_tx_node_cleanup+0x185/0x1b0 [ath9k]
[<ffffffffa0345597>] ath9k_sta_notify+0x57/0xb0 [ath9k]
[<ffffffffa02ac51a>] __sta_info_unlink+0x15a/0x260 [mac80211]
[<ffffffffa02ac658>] sta_info_unlink+0x38/0x60 [mac80211]
[<ffffffffa02b3fbe>] ieee80211_set_disassoc+0x1ae/0x210 [mac80211]
[<ffffffffa02b42d9>] ieee80211_mgd_deauth+0x109/0x110 [mac80211]
[<ffffffffa02ba409>] ieee80211_deauth+0x19/0x20 [mac80211]
[<ffffffffa028160e>] __cfg80211_mlme_deauth+0xee/0x130 [cfg80211]
[<ffffffff81118540>] ? init_object+0x50/0x90
[<ffffffffa0285429>] __cfg80211_disconnect+0x159/0x1d0 [cfg80211]
[<ffffffffa027125f>] cfg80211_netdev_notifier_call+0x10f/0x450 [cfg80211]
[<ffffffff81514ca7>] notifier_call_chain+0x47/0x90
[<ffffffff8107f501>] raw_notifier_call_chain+0x11/0x20
[<ffffffff81442d66>] call_netdevice_notifiers+0x16/0x20
[<ffffffff8144352d>] dev_close+0x4d/0xa0
[<ffffffff814439a8>] rollback_registered+0x48/0x120
[<ffffffff81443a9d>] unregister_netdevice+0x1d/0x70
[<ffffffffa02b6cc4>] ieee80211_remove_interfaces+0x84/0xc0 [mac80211]
[<ffffffffa02aa072>] ieee80211_unregister_hw+0x42/0xf0 [mac80211]
[<ffffffffa0347bde>] ath_detach+0x8e/0x180 [ath9k]
[<ffffffffa0347ce1>] ath_cleanup+0x11/0x50 [ath9k]
[<ffffffffa0351a2c>] ath_pci_remove+0x1c/0x20 [ath9k]
[<ffffffff8129d712>] pci_device_remove+0x32/0x60
[<ffffffff81332373>] __device_release_driver+0x53/0xb0
[<ffffffff81332498>] driver_detach+0xc8/0xd0
[<ffffffff81331405>] bus_remove_driver+0x85/0xe0
[<ffffffff81332a5a>] driver_unregister+0x5a/0x90
[<ffffffff8129da00>] pci_unregister_driver+0x40/0xb0
[<ffffffffa03518d0>] ath_pci_exit+0x10/0x20 [ath9k]
[<ffffffffa0353cd5>] ath9k_exit+0x9/0x2a [ath9k]
[<ffffffff81092838>] sys_delete_module+0x1a8/0x270
[<ffffffff8107ebe9>] ? up_read+0x9/0x10
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
---[ end trace fad957019ffdd40b ]---
phy0: Removed STA 00:22:6b:56:fd:e8
phy0: Destroyed STA 00:22:6b:56:fd:e8
wlan31: deauthenticating from 00:22:6b:56:fd:e8 by local choice (reason=3)
ath9k 0000:16:00.0: PCI INT A disabled
The original lockdep fixed an issue where due to the new changes
the driver was not disabling the bottom halves but it is incorrect
to do this on the older kernels since IRQs are already disabled.
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 93a59d7527147e3656664aa3179f8d19de256081 upstream.
James Grossmann [1] reported that p54 spews out confusing
messages instead of preventing the mayhem from happening.
the reason is that "p54: generate channel list dynamically"
is not perfect. It didn't discard incomplete channel data
sets and therefore p54 advertised to support them as well.
[1]: http://marc.info/?l=linux-wireless&m=125699830215890
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: James Grossmann <cctsurf@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a9e10fb9b1c6ad16e73cf2656951fce3a817611e upstream.
All the queues are awake and ready to use after loading firmware,
for firmware reload case, if any queues was stopped before
reload, mac80211 will wake those queues after restart hardware, so make
sure all the flag used to keep track of the queue status are
reset correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c441b8d2cb2194b05550a558d6d95d8944e56a84 upstream.
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped. The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).
This can be prevented by increasing the GRC timeout value for these
register read and write operations.
Thanks to Dell for helping us debug this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit dc8bf1b1a6edfc92465526de19772061302f0929 upstream.
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 908ba2bfd22253f26fa910cd855e4ccffb1467d0 upstream.
78f1cd02457252e1ffbc6caa44a17424a45286b8 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 78f1cd02457252e1ffbc6caa44a17424a45286b8 upstream.
This is quite similar to b39fe41f481d20c201012e4483e76c203802dda7
though said registers are not even documented as 64-bit registers
- as opposed to the initial TxDescStartAddress ones - but as single
bytes which must be combined into 32 bits at the MMIO read/write
level before being merged into a 64 bit logical entity.
Credits go to Ben Hutchings <ben@decadent.org.uk> for the MAR
registers (aka "multicast is broken for ages on ARM) and to
Timo Teräs <timo.teras@iki.fi> for the MAC registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4c020a961a812ffae9846b917304cea504c3a733 upstream.
r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.
Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 088ea189c4c75cdf211146faa4b341a0f7476be6 upstream.
fix off by one error in the queue size check of p54_tx_qos_accounting_alloc()
Coverity CID: 13314
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
