| Age | Commit message (Collapse) | Author |
|---|
|
Across all SoCs, even on Armada 370 for SPI0, the clock pin uses the
'sck' subname and not 'clk', so this commit adjusts the code and
documentation accordingly.
Since this commit only changes the subname, DT backward compatibility
is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For consistency with the datasheet, this commit renames the VDD
function of the MPP4 pin.
While this changes the DT compatibility, it is not considered to be a
problem since this pin is unlikely to be used for anything but
debugging purposes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit normalizes the naming of the Ethernet txclkout pin to be
the same accross Marvell SoCs. It is worth mentioning that the DT
binding documentation of the Armada XP was wrong for MPP12: it said
the function was ge1(txd0), while it is in fact ge1(txclkout). It is
however not really a fix worth sending to stable since it does not
change the behavior, and the driver itself was correct.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit aligns the naming of the audio 'lrclk' pin accross Marvell
SoCs.
Since only the subname is changed, the DT backward compatibility is
not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit normalizes the naming of PCIe pins to use 'rstout' instead
of 'rstoutn' or 'rst-out'.
Since only the subnames are changed, DT compatibility is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit normalizes the naming of the TDM pins accross the
different Marvell SoCs. Mainly it consists in:
* Removing the 'n' from signal names: 'intn' becomes 'int' and 'rstn'
becomes 'rst'
* Renaming the main name 'tdm2c' to 'tdm' on Armada 38x.
* Change the main name 'tdm-1' to 'tdm' for one of the pins of the
Armada XP
The last two changes affect DT compatibility, but since the TDM
interface is nowhere near being supported in mainline, it should not
be considered to be a serious problem at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All SoCs use "nand" to designate NAND pins, only Armada 39x is using
"nd", which is not consistent. This commit fixes that by renaming the
corresponding functions.
It also changes the subnames from rbn0/rbn1 to rb0/rb1, to respect the
convention used everywhere that we don't encode the 'n' part of signal
names.
While this commit changes the main name of function, therefore
potentially breaking the DT compatibility, this is not a problem since
Armada 39x is a brand new SoC which isn't used in production yet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit modifies the definition of the Device Bus interface pins
to be consistent accross SoCs. Especially, it removes the 'n'
indicators that we don't encode in the subnames of pins:
'dev(wen0)' becomes 'dev(we0)'
'dev(wen1)' becomes 'dev(we1)'
'dev(oen)' becomes 'dev(oe)'
etc.
In addition, it fixes the Armada 375 DT binding documentation, which
forgot to document the 'dev' function for MPP46, MPP57 and MPP63.
Since only the subnames are changed, this commit does not affect DT
compatibility.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to be consistent with the datasheet and some other SoCs, this
commit renames the SDIO pins of the Armada 39x from "sd" to "sd0".
While this changes the DT binding, this is not a problem since Armada
39x is a brand new SoC which isn't used in production yet (so now is
the right time to fix such things).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit makes the naming of SATA related MPP functions consistent
accross SoCs by adjusting the Armada 39x definition to use "prsnt"
instead of "present".
Since only the subnames are changed, the DT binding is not modified at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit makes the dram functions naming (both the name and
subname) consistent accross SoC, by using:
dram(vttctrl)
dram(deccerr)
in all Marvell SoCs.
Due to the change to the name, it changes the DT binding, but these
functions are not used by any in-tree Device Tree file, and are very
unlikely to be used by anyone.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The subnames are purely informative, but it's nicer when they match
accross SoCs. This commit adjusts the Armada 375, Armada 38x and
Armada 39x MPP definitions so that the subnames of the PTP pins match
the ones used on Armada XP and Kirkwood.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pinctrl_gpio_range[] array described a first bank of 32 GPIOs and
a second one of 27 GPIOs. However, since there is a total of 60 MPP
pins that can be muxed as GPIOs, the second bank really has 28 GPIOs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.1+
Fixes: ee086577abe7f ("pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pinctrl_gpio_range[] array described a first bank of 32 GPIOs and
a second one of 27 GPIOs. However, since there is a total of 60 MPP
pins that can be muxed as GPIOs, the second bank really has 28 GPIOs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b56f ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There was an incorrect space in the definition of the function of one
pin in the Armada 375 pinctrl driver, which this commit fixes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ce3ed59dcddd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ce3ed59dcddd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 5f597bb2be57 ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b56f ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds suspend/resume support to the Armada XP pinctrl
driver, by simply saving and restoring the MPP registers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MPP19 and MMP20 pins also have the ability to be muxed to the uart1
function.
Add this case to the pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
commit 2243a87d90b42eb38bc281957df3e57c712b5e56
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit extends the pinctrl mvebu logic with a new driver to cover
Orion5x SoC. It supports the definitions for the 5181l, 5182 and 5281
variants of Orion5x, which are the three ones supported by the old
style MPP code in arch/arm/mach-orion5x/.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pinctrl will WARN on missing DT resources, which is a little bit too
noisy. Use dev_warn with FW_BUG instead.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Sign for-mvebu/pinctrl-3xx
|
|
Now that we have a regmap for global registers, get rid of the last
remaining hardcoded physical addresses. While at it, also remove
DOVE_ prefix from those macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have ioremapped pmu_mpp registers, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have an ioremapped mpp4 register, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have ioremapped mpp base registers, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dove pinctrl uses some global config registers to control pins.
This patch requests a syscon regmap for those registers. As this
changes DT to driver requirements, fallback to a self-registered
regmap with hardcoded resources, if the corresponding syscon DT
node is missing. Also, WARN about old DT binding usage to encourage
users to update their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dove pinctrl also requires additional registers to control all pins.
This patch requests resources for mpp4 and pmu-mpp register ranges.
As this changes DT to driver requirements, fallback to hardcoded
resources, if the corresponding DT regs have not been set.
Also, WARN about old DT binding usage to encourage users to update
their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Marvell Armada 380/385 are new ARM SoCs from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
The Marvell Armada 375 is a new ARM SoC from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Dove has pins that can be switched between normal and pmu functions.
Rework pmu_mpp callbacks to reuse default mpp ctrl helpers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Passing a NULL name for pin ranges will auto-generate standard names
for each pin. With common pinctrl driver now checking NULL name correctly,
consolidate mpp pins 0-15.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Now that each per-SoC pinctrl driver must implement its own get/set
functions, there is no point in keeping the MPP_REG_CTRL macro, whose
purpose was to let the core pinctrl mvebu driver use default get/set
functions. While at it also update the comment about mvebu_mpp_ctrl.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
With every SoC always providing its own get/set callbacks, we can now
remove the generic ones, remove the obsolete base address, and always
use the provided callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
The way that mvebu pinctrl is designed, requesting mpp registers
in common pinctrl driver does not allow SoC specific drivers to
access this resource.
Move resource allocation in each SoC pinctrl driver and enable
already provided mpp_{set,get} callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
|
|
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later. While at it, also make use of globally defined
MPP macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
This adds some defines and helper functions for the common mpp reg
layout to mvebu pinctrl include.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
|
