summaryrefslogtreecommitdiff
path: root/drivers/s390/net
AgeCommit message (Collapse)Author
2009-05-28Merge branch 'quilt/driver-core'Stephen Rothwell
Conflicts: init/main.c
2009-05-20qeth: Clear SBALF15 in any case for output buffers.Klaus-Dieter Wacket
Function qeth_clear_output_buffer for HiperSockets may not clear all 16 SBALEs, but only the used ones. The error flag in SBALF15 has to be cleared in any case. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-20qeth: omit upstream checksumming for HiperSocketsUrsula Braun
For HiperSocket devices receive-path checksumming is not required. Thus NO_CHECKSUMMING is used as default for HiperSocket interfaces. For layer3 devices configured with NO_CHECKSUMMING received skbs should have set their ip_summed field to CHECKSUM_UNNECESSARY. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-20qeth: support z/VM VSWITCH Port IsolationUrsula Braun
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE virtual switch to be isolated from other guests on the VSWITCH. (See z/VM Apars VM64281 and VM64463). The Linux qeth driver is affected, because it has to handle new error codes introduced with the z/VM VSWITCH Port Isolation support. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-20ctcm: avoid crash in ctcm_remove_deviceUrsula Braun
Channels are already removed when setting a ctcm-device offline. Thus ctcm_remove_device must not refer to channel information. Solution: delete channel information from the trace call in ctcm_remove_device. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-20qeth: avoid crash after detach of replugged deviceUrsula Braun
If a qeth device is plugged off, setting the device online stops in state HARDSETUP and a failure is reported to the base cio-layer causing halt/clear to be invoked. Replugging the device again triggers a qeth recovery without notification of the cio-layer. If a device is ungrouped in this state, the qeth set_offline function is not invoked, because the corresponding ccwgroup device is not in state ONLINE. Then incoming traffic is still handled by the qdio layer resulting in a crash in qeth_l<x>_qdio_input_handler, because (part of) the qeth data structures for this device are already removed. Solution: After replugging the device qeth recovery should lead to a working net device. Thus a "LAN offline" result when setting a qeth device online must not report a failure to the base cio-layer. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-21s390: remove driver_data direct access of struct deviceGreg Kroah-Hartman
In the near future, the driver core is going to not allow direct access to the driver_data pointer in struct device. Instead, the functions dev_get_drvdata() and dev_set_drvdata() should be used. These functions have been around since the beginning, so are backwards compatible with all older kernel versions. Thanks to Sebastian Ott <sebott@linux.vnet.ibm.com> for fixing a few typos in my original version of this patch. Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sebastian Ott <sebott@linux.vnet.ibm.com> Cc: linux-s390@vger.kernel.org Cc: linux390@de.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-01qeth: properly delete empty files.Linus Torvalds
Commit 64ef8957986f6a04f61e7c95fa6ffeb3a86a6661 ("qeth: remove EDDP") removed the qeth_core_offl.[hc] files, but ended up doing so by just patching them to zero size, rather than removing them properly. Actually remove the files. Reported-by: Andrew Price <andy@andrewprice.me.uk> Cc: Frank Blaschka <frank.blaschka@de.ibm.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-26Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits) [S390] remove duplicated #includes [S390] cpumask: use mm_cpumask() wrapper [S390] cpumask: Use accessors code. [S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits. [S390] cpumask: remove cpu_coregroup_map [S390] fix clock comparator save area usage [S390] Add hwcap flag for the etf3 enhancement facility [S390] Ensure that ipl panic notifier is called late. [S390] fix dfp elf hwcap/facility bit detection [S390] smp: perform initial cpu reset before starting a cpu [S390] smp: fix memory leak on __cpu_up [S390] ipl: Improve checking logic and remove switch defaults. [S390] s390dbf: Remove needless check for NULL pointer. [S390] s390dbf: Remove redundant initilizations. [S390] use kzfree() [S390] BUG to BUG_ON changes [S390] zfcpdump: Prevent zcore from beeing built as a kernel module. [S390] Use csum_partial in checksum.h [S390] cleanup lowcore.h [S390] eliminate ipl_device from lowcore ...
2009-03-26[S390] qdio: report SIGA errors directlyJan Glauber
Errors from SIGA instructions are stored in the per queue qdio_error and reported back when the queue handler is called. That opens a race when multiple error conditions occur simultanously. Report SIGA errors immediately in the return value of do_QDIO so the upper layer can react and SIGA errors no longer interfere with other errors. Move the SIGA error handling in qeth from the outbound handler to qeth_flush_buffers. Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
2009-03-25qeth: fix wait_event_timeout handlingHeiko Carstens
wait_event_timeout just takes the numnber of jiffies to wait as an argument. That value does not include jiffies itself. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25qeth: check for completion of a running recoveryUrsula Braun
When a recovery is started for a qeth device, additional invocations to change a mac address, to configure a VLAN interface on top, or to add multicast addresses should wait till recovery is finished, otherwise recovery might fail. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25qeth: unregister MAC addresses during recovery.Klaus-Dieter Wacker
qeth: Unregister MAC addresses from device (layer 2) during recovery cycle. When the device is set online the MAC addresses are registered again on the device. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25qeth: remove EDDPFrank Blaschka
Performance measurements showed EDDP does not lower CPU costs but increase them. So we dump out EDDP code from qeth driver. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25qeth: add statistics for tx csumFrank Blaschka
Add statistics counter for software tx checksumming. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25qeth: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24claw: fix minor findings from code analysis toolAndrew H. Richter
This patch fixes two problems in the claw driver identified by static code analysis: o Change in case differentiation of received sense codes o Use correct data length in claw hard_start_xmit routine Signed-off-by: Andrew H. Richter <richtera@us.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24ctcm: fix minor findings from code analysis toolJoel A. Fowler
From: Ursula Braun <ursula.braun@de.ibm.com> This patch fixes problems in the ctcm driver identified by static code analysis: o remove an unnecessary always true condition in ctcm_unpack_skb o remove duplicate assignment in ctc_mpc_alloc_channel o remove an unnecessary always true condition in ctcmpc_send_sweep_resp o remove duplicate initialization in ctcmpc_unpack_skb o shorten if condition in mpc_action_go_inop o remove INOP event if mpc group is undefined in mpc_action_doxid7 Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24ctcm: avoid wraparound in length of incoming dataRoel Kluin
Since the receive code should tolerate any incoming garbage, it should be protected against a potential wraparound when manipulating length values within incoming data. block_len is unsigned, so a too large subtraction will cause a wraparound. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24ctcm: invalid return code from hard_start_xmitUrsula Braun
Avoid kernel warning by using the correct hard_start_xmit return code NETDEV_TX_BUSY for skb requeuing. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24claw: invalid return codes from hard_start_xmitUrsula Braun
Avoid kernel warnings by using the correct hard_start_xmit return code NETDEV_TX_BUSY for skb requeuing. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24netiucv: invalid return code from hard_start_xmitUrsula Braun
Avoid kernel warning by using the correct hard_start_xmit return code NETDEV_TX_BUSY for skb requeuing. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24lcs: invalid return codes from hard_start_xmit.Klaus-Dieter Wacker
Lcs hard_start_xmit routine issued return codes other than defined for this interface. Now lcs returns only either NETDEV_TX_OK or NETDEV_TX_BUSY. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-24Use kthread instead of kernel_threadKlaus-Dieter Wacker
Lcs uses low-level kernel_thread implementation. All drivers should use <linux/kthread.h> API instead. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-26Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2009-01-25kmsg: convert claw printk messagesAndy Richter
claw printks are converted to dev_xxx and pr_xxx macros. Signed-off-by: Andy Richter <richtera@us.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-25lcs: fix compilation for !CONFIG_IP_MULTICASTHeiko Carstens
drivers/s390/net/lcs.c: In function 'lcs_new_device': drivers/s390/net/lcs.c:2179: error: implicit declaration of function 'lcs_set_multicast_list' Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21claw: convert to net_device_opsFrank Blaschka
claw convert to net_device_ops. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21netiucv: convert to net_device_opsFrank Blaschka
netiucv convert to net_device_ops. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21ctcm: convert to net_device_opsFrank Blaschka
ctcm convert to net_device_ops. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21lcs: convert to net_device_opsFrank Blaschka
lcs convert to net_device_ops. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11qeth: fix usage of netdev_opsFrank Blaschka
Have separate netdev_ops for OSA and HiperSocket/TR. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-08Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
2009-01-08qeth: convert to net_device_opsFrank Blaschka
qeth_l2, qeth_l3 convert to net_device_ops. qeth_l3 remove vlan neigh_setup hack since it does not work any longer with the new net_device_ops. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-06s390: remove s390_root_dev_*()Mark McLoughlin
Replace s390_root_dev_register() with root_device_register() etc. [Includes fix from Cornelia Huck] Signed-off-by: Mark McLoughlin <markmc@redhat.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-04qeth: get rid of extra argument after printk to dev_* conversionHeiko Carstens
drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_setadapter_parms': drivers/s390/net/qeth_l3_main.c:1049: warning: too many arguments for format Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-04qeth: No large send using EDDP for HiperSockets.Klaus-Dieter Wacker
From: Klaus-Dieter Wacker <kdwacker@de.ibm.com> The device driver qeth dos not support large send using EDDP for HiperSockets. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-04qeth: do not spin for SETIP ip assist commandFrank Blaschka
The ip assist hw command for setting an IP address last unacceptable long so we can not spin while we waiting for the irq. Since we can ensure process context for all occurrences of this command we can use wait. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-04qeth: avoid crash in case of layer mismatch for VSWITCHUrsula Braun
For z/VM GuestLAN or VSWITCH devices the transport layer is configured in z/VM. The layer2 attribute of a participating Linux device has to match the z/VM definition. In case of a mismatch Linux currently crashes in qeth recovery due to a reference to the not yet existing net_device. Solution: add a check for existence of net_device and add a message pointing to the mismatch of layer definitions in Linux and z/VM. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-04qeth: exploit source MAC address for inbound layer3 packetsUrsula Braun
OSA-devices operating in layer3 mode offer adding of the source MAC address to the QDIO header of inbound packets. The qeth driver can exploit this functionality to replace FAKELL-entries in the ethernet header of received packets. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-04qeth: HiperSockets mcl string conversion (pre z9 mach)Klaus-Dieter Wacker
The pre z9 machines provide an mcl string in EBCDIC format, z9 or later provide string in ASCII format. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits) net: Allow dependancies of FDDI & Tokenring to be modular. igb: Fix build warning when DCA is disabled. net: Fix warning fallout from recent NAPI interface changes. gro: Fix potential use after free sfc: If AN is enabled, always read speed/duplex from the AN advertising bits sfc: When disabling the NIC, close the device rather than unregistering it sfc: SFT9001: Add cable diagnostics sfc: Add support for multiple PHY self-tests sfc: Merge top-level functions for self-tests sfc: Clean up PHY mode management in loopback self-test sfc: Fix unreliable link detection in some loopback modes sfc: Generate unique names for per-NIC workqueues 802.3ad: use standard ethhdr instead of ad_header 802.3ad: generalize out mac address initializer 802.3ad: initialize ports LACPDU from const initializer 802.3ad: remove typedef around ad_system 802.3ad: turn ports is_individual into a bool 802.3ad: turn ports is_enabled into a bool 802.3ad: make ntt bool ixgbe: Fix set_ringparam in ixgbe to use the same memory pools. ... Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due to the conversion to %pI (in this networking merge) and the addition of doing IPv6 addresses (from the earlier merge of CIFS).
2008-12-25[S390] convert ctcm printks to dev_xxx and pr_xxx macros.Peter Tiedemann
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] convert qeth printks to dev_xxx and pr_xxx macros.Frank Blaschka
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] convert iucv printks to dev_xxx and pr_xxx macros.Ursula Braun
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] convert lcs printks to dev_xxx and pr_xxx macros.Klaus-D. Wacker
Signed-off-by: Klaus-D. Wacker <kdwacker@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] s390: Remove redundant testJulia Lawall
The loop above the modified code only terminates when rc is a valid pointer. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] service level interface.Martin Schwidefsky
Add a new proc interface /proc/service_levels that allows any code to report a relevant service level, e.g. the microcode level of devices, the service level of the hypervisor, etc. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] qdio: fix qeth port count detectionJan Glauber
qeth needs to get the port count information before qdio has allocated a page for the chsc operation. Extend qdio_get_ssqd_desc() to store the data in the specified structure. Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-06s390_net: Kill directly reference of netdev->privWang Chen
The private data comes from ccwgroup_device. So just don't allocate private data memory when do alloc_netdev() and use netdev->ml_priv to reference private data. Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-15 03:47:27 +0000