| Age | Commit message (Collapse) | Author |
|---|
|
After relogin is sucessful, "send_els_logo" flag needs to be
reinitialized. This will allow next re-login to happen successfully.
In target mode, this flag was not reset correctly, causing IO's failure
during reset recovery and port ON/OFF test cases from initiator.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When RSCN is delivered for specific remote port. Use ADISC to verify the
session is still valid or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If SNS fabric login fails, set loop resync flag to retry via dpc.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For NPIV ports, call configure_hba() so that NPIV ports can proceed to
loop initialization.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes: 4b60c82736d0 ("scsi: qla2xxx: Add fw_started flags to qpair")
Cc: <stable@vger.kernel.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix the following typos/spelling mistakes:
"attribure" -> "attribute"
"suppored" -> "supported"
"Symobilic" -> "Symbolic"
"iteself" -> "itself"
"reqeust" -> "request"
"nvme_wait_on_comand" -> "nvme_wait_on_command"
"bount" -> "bound"
"captrue_mask" -> "capture_mask"
"tempelate" -> "template"
..and also unwrap a line to fix a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds switch command support for FC-4 type of FC-NVMe (0x28)
for resgistering HBA port to the management server. RFT_ID command is
used to register FC-4 type of 0x28 and RFF_ID is used to register FC-4
features bits for FC-NVMe port.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).
Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add missing memory dump of Exchange Offload and Extended login into FW
dump.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add call back to door bell for qpair. This help reduce access to
qla_hw_data structure, in order to reduce cach thrash.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For ISP27XX, use shadow register to read FW provided REQQ's consumer
index. The shadow register is dma'ed by firmware.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
- Move chip_reset, enable_class_2 fields from qla_hw_data to qla_qpair
to reduce cache thrash for target MQ.
- Optimizations to reduce unnecessary memory load for good path io.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add fw_started flag to qpair to reduce cache thrash. This reduce access
to qla_hw_data structure by each qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In target mode driver, queue pairs are not created during driver load
time, instead they are created at the configuration time after chip
reset. If a user tries to load/unload driver after queue pairs are
created, then there would be mailbox failure, while deleting queue
pairs. Flag is added to check if queue pairs are created or not. Queue
pairs will be deleted only If they were created during target
configuration.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Enable Multi Queue for Target mode. At Initiator LUN scan time, each LUN
is assign to a QPair. Each QPair is affinitize to certain CPU. When new
cmd arrives from the wire, the lunid is used to search for qpair. The
qpair's affinitized cpuid will be used to queue up the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair". Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes following 0-day kernel build warnings:
drivers/scsi/qla2xxx/qla_init.c:6407:50: warning: format '%lx' expects
argument of type 'long unsigned int', but argument 5 has type 'unsigned
int' [-Wformat=]
drivers/scsi/qla2xxx/qla_init.c:6709:50: warning: format '%lx'
expects argument of type 'long unsigned int', but argument 5 has
type 'unsigned int' [-Wformat=]
Fixes: b95b9452aacf ("scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Accelerate generation of SCSI busy to let initiators slow down when
target is running low in resources.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.
Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.
With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.
With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Tell FW to track exchange/cmd state to prevent driver from using stale
exchange or exchange that is not meant for this command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Assign unique id to all traces and logs for debug purpose.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Name server login is normally handle by FW. In some rare case where one
of the switches is being updated, name server login could get
affected. Trigger relogin to name server when driver detects this
condition.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver added mechanism to move ABTS/PUREX/RIDA mailbox to
ATIO queue as part of commit id 41dc529a4602ac737020f423f84686a81de38e6d
("qla2xxx: Improve RSCN handling in driver").
This patch adds a check to only allow ABTS/PURX/RIDA
to be moved to ATIO Queue for ISP83XX and ISP27XX.
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
queue
when driver is loaded with Multi Queue enabled, it was noticed that
there was one less queue pair created.
Following message would indicate this:
"No resources to create additional q pair."
The result of one less queue pair means that system can crash, if the
block mq layer thinks there is an extra hardware queue available, and
the driver will use a NULL ptr qpair in that instance.
Following stack trace is seen in one of the crash:
irq_create_affinity_masks+0x98/0x530
irq_create_affinity_masks+0x98/0x530
__pci_enable_msix+0x321/0x4e0
mutex_lock+0x12/0x40
pci_alloc_irq_vectors_affinity+0xb5/0x140
qla24xx_enable_msix+0x79/0x530 [qla2xxx]
qla2x00_request_irqs+0x61/0x2d0 [qla2xxx]
qla2x00_probe_one+0xc73/0x2390 [qla2xxx]
ida_simple_get+0x98/0x100
kernfs_next_descendant_post+0x40/0x50
local_pci_probe+0x45/0xa0
pci_device_probe+0xfc/0x140
driver_probe_device+0x2c5/0x470
__driver_attach+0xdd/0xe0
driver_probe_device+0x470/0x470
bus_for_each_dev+0x6c/0xc0
driver_attach+0x1e/0x20
bus_add_driver+0x45/0x270
driver_register+0x60/0xe0
__pci_register_driver+0x4c/0x50
qla2x00_module_init+0x1ce/0x21e [qla2xxx]
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates
(hisi_sas, ufs, fnic, cxlflash, be2iscsi, ipr, stex). There's also the
usual amount of cosmetic and spelling stuff"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (155 commits)
scsi: qla4xxx: fix spelling mistake: "Tempalate" -> "Template"
scsi: stex: make S6flag static
scsi: mac_esp: fix to pass correct device identity to free_irq()
scsi: aacraid: pci_alloc_consistent() failures on ARM64
scsi: ufs: make ufshcd_get_lists_status() register operation obvious
scsi: ufs: use MASK_EE_STATUS
scsi: mac_esp: Replace bogus memory barrier with spinlock
scsi: fcoe: make fcoe_e_d_tov and fcoe_r_a_tov static
scsi: sd_zbc: Do not write lock zones for reset
scsi: sd_zbc: Remove superfluous assignments
scsi: sd: sd_zbc: Rename sd_zbc_setup_write_cmnd
scsi: Improve scsi_get_sense_info_fld
scsi: sd: Cleanup sd_done sense data handling
scsi: sd: Improve sd_completed_bytes
scsi: sd: Fix function descriptions
scsi: mpt3sas: remove redundant wmb
scsi: mpt: Move scsi_remove_host() out of mptscsih_remove_host()
scsi: sg: reset 'res_in_use' after unlinking reserved array
scsi: mvumi: remove code handling zero scsi_sg_count(scmd) case
scsi: fusion: fix spelling mistake: "Persistancy" -> "Persistency"
...
|
|
Signed-off-by: Milan P Gandhi <mgandhi@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
|
|
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the following warning reported by the "smatch" static checker:
drivers/scsi/qla2xxx/qla_init.c:3910 qla2x00_alloc_fcport()
warn: use 'flags' here instead of GFP_XXX?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch simplifies SRB structure usage in driver.
- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Current code merges qla_tgt_sess and fc_port structure
into single fc_port structure representing same I-T nexus.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Soft reset and Risc reset should take 100uS to complete.
This change pad the timeout up to 400uS, which should be
plenty.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
- Fix race condition between dpc_thread accessing Multiqueue resources
and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
interrupts needs a workqueue. Interrupt needed to stop before
the wq can be destroyed.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.
Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.
Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
