Age | Commit message (Collapse) | Author |
|
commit 456244aeecd54249096362a173dfe06b82a5cafa upstream.
Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
Fixes: d0ed062a8b75 ("usb: mtu3: dual-role mode support")
Cc: stable@vger.kernel.org
Tested-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Tainping Fang <tianping.fang@mediatek.com>
Link: https://lore.kernel.org/r/20220419081245.21015-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3d4621c22f90c33321ae6a6baab60cdb8e5a77c ]
Use the Interval value from isoc/intr endpoint descriptor, no need
minus one. The original code doesn't cause transfer error for
normal cases, but it may have side effect with respond time of ERDY
or tPingTimeout.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 43f3b8cbcf93da7c2755af4a543280c31f4adf16 upstream.
Add support to set interval also for FS intr and isoc endpoint.
Fixes: 4d79e042ed8b ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c313e3bfd9adae8d5c4ba1cc696dcbc86fbf9bf upstream.
This is caused by uninitialization of list_head.
BUG: KASAN: use-after-free in __list_del_entry_valid+0x34/0xe4
Call trace:
dump_backtrace+0x0/0x298
show_stack+0x24/0x34
dump_stack+0x130/0x1a8
print_address_description+0x88/0x56c
__kasan_report+0x1b8/0x2a0
kasan_report+0x14/0x20
__asan_load8+0x9c/0xa0
__list_del_entry_valid+0x34/0xe4
mtu3_req_complete+0x4c/0x300 [mtu3]
mtu3_gadget_stop+0x168/0x448 [mtu3]
usb_gadget_unregister_driver+0x204/0x3a0
unregister_gadget_item+0x44/0xa4
Fixes: 83374e035b62 ("usb: mtu3: add tracepoints to help debug")
Cc: stable@vger.kernel.org
Reported-by: Yuwen Ng <yuwen.ng@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7aae769ca626819a7f9f078ebdc69a8a1b00c81 upstream.
There is a seldom issue that the controller access invalid address
and trigger devapc or emimpu violation. That is due to memory access
is out of order and cause gpd data is not correct.
Add mb() to prohibit compiler or cpu from reordering to make sure GPD
is fully written before setting its HWO.
Fixes: 48e0d3735aa5 ("usb: mtu3: supports new QMU format")
Cc: stable@vger.kernel.org
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44e4439d8f9f8d0e9da767d1f31e7c211081feca upstream.
usb_endpoint_maxp() returns actual max packet size, @mult will
always be zero, fix it by using usb_endpoint_maxp_mult() instead
to get mult.
Fixes: 4d79e042ed8b ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd7cb394ec7efccc3985feb0978cee4d352e1817 upstream.
For HS isoc or intr, should use @mult but not @burst
to save mult value.
Fixes: 4d79e042ed8b ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e88f28514065a6c48aadc367efb0ef6378a01543 upstream.
Due to HS function is disabled when set as FS, need restore
it when set as SS/SSP.
Fixes: dc4c1aa7eae9 ("usb: mtu3: add ->udc_set_speed()")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f6f6343a29d9ea7429306b83b18e66dc1331d5c upstream.
This code is using the wrong sizeof() so it does not allocate enough
memory. It allocates 32 bytes but 72 are required. That will lead to
memory corruption.
Fixes: ae07809255d3 ("usb: mtu3: add debugfs interface files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikqc4Mo2/0G72j@mwanda
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a possible issue when mtu3_gadget_stop()
already assigned NULL to mtu->gadget_driver during mtu_gadget_disconnect().
[<ffffff9008161974>] notifier_call_chain+0xa4/0x128
[<ffffff9008161fd4>] __atomic_notifier_call_chain+0x84/0x138
[<ffffff9008162ec0>] notify_die+0xb0/0x120
[<ffffff900809e340>] die+0x1f8/0x5d0
[<ffffff90080d03b4>] __do_kernel_fault+0x19c/0x280
[<ffffff90080d04dc>] do_bad_area+0x44/0x140
[<ffffff90080d0f9c>] do_translation_fault+0x4c/0x90
[<ffffff9008080a78>] do_mem_abort+0xb8/0x258
[<ffffff90080849d0>] el1_da+0x24/0x3c
[<ffffff9009bde01c>] mtu3_gadget_disconnect+0xac/0x128
[<ffffff9009bd576c>] mtu3_irq+0x34c/0xc18
[<ffffff90082ac03c>] __handle_irq_event_percpu+0x2ac/0xcd0
[<ffffff90082acae0>] handle_irq_event_percpu+0x80/0x138
[<ffffff90082acc44>] handle_irq_event+0xac/0x148
[<ffffff90082b71cc>] handle_fasteoi_irq+0x234/0x568
[<ffffff90082a8708>] generic_handle_irq+0x48/0x68
[<ffffff90082a96ac>] __handle_domain_irq+0x264/0x1740
[<ffffff90080819f4>] gic_handle_irq+0x14c/0x250
[<ffffff9008084cec>] el1_irq+0xec/0x194
[<ffffff90085b985c>] dma_pool_alloc+0x6e4/0xae0
[<ffffff9008d7f890>] cmdq_mbox_pool_alloc_impl+0xb0/0x238
[<ffffff9008d80904>] cmdq_pkt_alloc_buf+0x2dc/0x7c0
[<ffffff9008d80f60>] cmdq_pkt_add_cmd_buffer+0x178/0x270
[<ffffff9008d82320>] cmdq_pkt_perf_begin+0x108/0x148
[<ffffff9008d824d8>] cmdq_pkt_create+0x178/0x1f0
[<ffffff9008f96230>] mtk_crtc_config_default_path+0x328/0x7a0
[<ffffff90090246cc>] mtk_drm_idlemgr_kick+0xa6c/0x1460
[<ffffff9008f9bbb4>] mtk_drm_crtc_atomic_begin+0x1a4/0x1a68
[<ffffff9008e8df9c>] drm_atomic_helper_commit_planes+0x154/0x878
[<ffffff9008f2fb70>] mtk_atomic_complete.isra.16+0xe80/0x19c8
[<ffffff9008f30910>] mtk_atomic_commit+0x258/0x898
[<ffffff9008ef142c>] drm_atomic_commit+0xcc/0x108
[<ffffff9008ef7cf0>] drm_mode_atomic_ioctl+0x1c20/0x2580
[<ffffff9008ebc768>] drm_ioctl_kernel+0x118/0x1b0
[<ffffff9008ebcde8>] drm_ioctl+0x5c0/0x920
[<ffffff900863b030>] do_vfs_ioctl+0x188/0x1820
[<ffffff900863c754>] SyS_ioctl+0x8c/0xa0
Fixes: df2069acb005 ("usb: Add MediaTek USB3 DRD driver")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604642069-20961-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200731082008.33016-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use argument req directly instead of mreq->request, they
are the same usb request.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not clear u3port's dual mode when disable device, the IP
will fail to enter sleep mode when suspend.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use MTU3_EP_WEDGE flag instead of the member @wedged in mtu3_ep
struct, then @wedged can be removed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-9-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The member @busy in mtu3_ep struct is unnecessary, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-8-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The caller already print error log.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make use of the method to make sure connect on speeds
supported by the gadget driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The max_speed got from DTS may be not supported by the
hardware, so need check it, and assign a proper default
value. And make it clear by introducing a funtion.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When disable interrupts, will also want to clear their status,
ensure it by calling mtu3_intr_status_clear() in
mtu3_intr_disable().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CSR registers will be reset as default value if the
ports are disabled, so reinitialize them when the ports
are enabled again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bits field for maximum number of packets is 8 bits.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The class driver will ensure the parameters are valid
pointers before call the hook function of usb_ep_ops,
so no need check them again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_platform_ioremap_resource_byname() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595404275-8449-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the header file containing a function's prototype isn't included by
the sourcefile containing the associated function, the build system
complains of missing prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/usb/mtu3/mtu3_trace.c:13:6: warning: no previous prototype for ‘mtu3_dbg_trace’ [-Wmissing-prototypes]
13 | void mtu3_dbg_trace(struct device *dev, const char *fmt, ...)
| ^~~~~~~~~~~~~~
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715093209.3165641-5-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Kerneldoc headers should only be used to document functions and data
structures.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715093209.3165641-4-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without it, the build system complains that it was declared inside
the parameter list.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/usb/mtu3/mtu3_trace.c:11:
drivers/usb/mtu3/mtu3_debug.h:29:36: warning: ‘struct ssusb_mtk’ declared inside parameter list will not be visible outside of this definition or declaration
29 | void ssusb_dev_debugfs_init(struct ssusb_mtk *ssusb);
| ^~~~~~~~~
drivers/usb/mtu3/mtu3_debug.h:30:35: warning: ‘struct ssusb_mtk’ declared inside parameter list will not be visible outside of this definition or declaration
30 | void ssusb_dr_debugfs_init(struct ssusb_mtk *ssusb);
| ^~~~~~~~~
drivers/usb/mtu3/mtu3_debug.h:31:39: warning: ‘struct ssusb_mtk’ declared inside parameter list will not be visible outside of this definition or declaration
31 | void ssusb_debugfs_create_root(struct ssusb_mtk *ssusb);
| ^~~~~~~~~
drivers/usb/mtu3/mtu3_debug.h:32:39: warning: ‘struct ssusb_mtk’ declared inside parameter list will not be visible outside of this definition or declaration
32 | void ssusb_debugfs_remove_root(struct ssusb_mtk *ssusb);
| ^~~~~~~~~
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
block
No attempt has been made to document the function.
Fixes the following W=1 kernel build warning(s):
drivers/usb/mtu3/mtu3_core.c:805: warning: Function parameter or member 'mtu' not described in 'mtu3_set_dma_mask'
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-26-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mtu3_prb_regs is never changed and can therefore be made const.
This allows the compiler to put it in the text section instead of the
data section.
Before:
text data bss dec hex filename
19966 7120 0 27086 69ce drivers/usb/mtu3/mtu3_debugfs.o
After:
text data bss dec hex filename
20142 6992 0 27134 69fe drivers/usb/mtu3/mtu3_debugfs.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch corrects the SPDX License Identifier style in
header files related to MediaTek USB3 Dual Role controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20200404103728.GA6011@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The declarations of ssusb_gadget_{init,exit} are
in the mtu3_dr.h file but the code does that implements
them does not include this. Add the include to fix the
following sparse warnigns:
drivers/usb/mtu3/mtu3_core.c:825:5: warning: symbol 'ssusb_gadget_init' was not declared. Should it be static?
drivers/usb/mtu3/mtu3_core.c:925:6: warning: symbol 'ssusb_gadget_exit' was not declared. Should it be static?
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
usb_composite_setup_continue() may be called before composite_setup()
return USB_GADGET_DELAYED_STATUS, then the controller driver will
delay status stage after composite_setup() finish, but the class driver
don't ask the controller to continue delayed status anymore, this will
cause control transfer timeout.
happens when use mass storage (also enabled other class driver):
cpu1: cpu2
handle_setup(SET_CONFIG) //gadget driver
unlock (g->lock)
gadget_driver->setup()
composite_setup()
lock(cdev->lock)
set_config()
fsg_set_alt() // maybe some times due to many class are enabled
raise FSG_STATE_CONFIG_CHANGE
return USB_GADGET_DELAYED_STATUS
handle_exception()
usb_composite_setup_continue()
unlock(cdev->lock)
lock(cdev->lock)
ep0_queue()
lock (g->lock)
//no delayed status, nothing todo
unlock (g->lock)
unlock(cdev->lock)
return USB_GADGET_DELAYED_STATUS // composite_setup
lock (g->lock)
get USB_GADGET_DELAYED_STATUS //handle_setup [1]
Try to fix the race condition as following:
After the driver gets USB_GADGET_DELAYED_STATUS at [1], if we find
there is a usb_request in ep0 request list, it means composite already
asked us to continue delayed status by usb_composite_setup_continue(),
so we skip request about delayed_status by composite_setup() and still
do status stage.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1570611900-7112-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exact a new static function to do status stage
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1570611900-7112-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Because extcon is not allowed for new bindings, and the
dual role switch is supported by USB Role Switch,
especially for Type-C drivers, so register a USB Role
Switch to support the new way
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1567070558-29417-12-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's not needed after [1] is applied, because usb_debug_root is created
by usb common core but not usbcore now.
[1] 812086d362a1 ("USB: move usb debugfs directory creation to the usb common core")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_USB is not set, and CONFIG_USB_GADGET is set,
there is an issue:
ld:
drivers/usb/mtu3/mtu3_debugfs.o: in function 'ssusb_debugfs_create_root':
mtu3_debugfs.c:(.text+0xba3): undefined reference to 'usb_debug_root'
usb_debug_root is only built when CONFIG_USB is enabled, so here drop it
and use NULL instead.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so
the replacement doesn't change original purpose.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When EXTCON is a loadable module, mtu3 fails to link as built-in:
drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe':
mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle'
Add a Kconfig dependency to force mtu3 also to be a loadable module
if extconn is, but still allow it to be built without extcon.
Fixes: d0ed062a8b75 ("usb: mtu3: dual-role mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
By introducing mailbox_state_string(), allow to make debug
log more readable
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch implements a few initial tracepoints for the
mtu3 driver. More traces can be added as necessary in order
to ease the task of debugging.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to the separated debugfs files are added, move vbus and mode
debugfs interfaces related with dual-role switch from mtu3_dr.c
into mtu3_debugfs.c
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds more debugfs consumers. The debugfs entries read some
important registers, fifo status, QMU ring, endpoint status, and
IPPC probe interface to get internal status.
With these entries, users can check the registers, endpoint and
GPD used during run time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to support U3gen2 ISOC transfer upto 96DPs, extend
the data buffer length.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To support USB3 Gen2 ISOC, the data buffer length need be extended,
it's hard to make the current qmu_gpd struct compatible, so here
rebuild qmu_gpd struct and make easy to support new QMU format
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To support USB3 Gen2 ISOC, the registers of TXCSR1 and RXCSR1
are adjusted to support greater maxpkt and mult value, this
patch fix this issue
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|