| Age | Commit message (Collapse) | Author |
|---|
|
commit f78e5623f45bab2b726eec29dc5cefbbab2d0b1c upstream.
The fastmap update code might erase the current fastmap anchor PEB
in case it doesn't find any new free PEB. When a power cut happens
in this situation we must not have any outdated fastmap anchor PEB
on the device, because that would be used to attach during next
boot.
The easiest way to make that sure is to erase all outdated fastmap
anchor PEBs synchronously during attach.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Fixes: dbb7d2a88d2a ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7d11b33d4e8cedf19367c09b891bbc705163976 upstream.
Usually Fastmap is free to consider every PEB in one of the pools
as newer than the existing PEB. Since PEBs in a pool are by definition
newer than everything else.
But update_vol() missed the case that a pool can contain more than
one candidate.
Cc: <stable@vger.kernel.org>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e8f08deabbc7eefe4c5838aaa6aa9a23a8acf2e upstream.
When writing a new Fastmap the first thing that happens
is refilling the pools in memory.
At this stage it is possible that new PEBs from the new pools
get already claimed and written with data.
If this happens before the new Fastmap data structure hits the
flash and we face power cut the freshly written PEB will not
scanned and unnoticed.
Solve the issue by locking the pools until Fastmap is written.
Cc: <stable@vger.kernel.org>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74f2c6e9a47cf4e508198c8594626cc82906a13d upstream.
Since PEB erasure is asynchornous it can happen that there is
more than one Fastmap on the MTD. This is fine because the attach logic
will pick the Fastmap data structure with the highest sequence number.
On a not so well configured MTD stack spurious ECC errors are common.
Causes can be different, bad hardware, wrong operating modes, etc...
If the most current Fastmap renders bad due to ECC errors UBI might
pick an older Fastmap to attach from.
While this can only happen on an anyway broken setup it will show
completely different sympthoms and makes finding the root cause much
more difficult.
So, be debug friendly and fall back to scanning mode of we're facing
an ECC error while scanning for Fastmap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdf10ed710c0aa177e8dfcd84e65e4e5e8e0956b upstream.
Introduce a new list to the UBI attach information
object to be able to deal better with old and corrupted
Fastmap eraseblocks.
Also move more Fastmap specific code into fastmap.c.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 243a4f8126fcf7facb04b324dbb7c85d10b11ce9 upstream.
This makes the logic more easy to follow.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 797097301860c64b63346d068ba4fe4992bd5021 upstream.
The post divider value in the frequency table is wrong as it would lead
to the PLL producing an output rate of 960 MHz instead of the desired
480 MHz. This wasn't a problem as nothing used the table to actually
initialize the PLL rate, but the bootloader configuration was used
unaltered.
If the bootloader does not set up the PLL it will fail to come when used
under Linux. To fix this don't rely on the bootloader, but set the
correct rate in the clock driver.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[jonathanh@nvidia.com: Back-ported to stable v4.4.y]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c456442cd3a59eeb1d60293c26cbe2ff2c4e42cf upstream
Add the sysfs file for the new vulerability. It does not do much except
show the words 'Vulnerable' for recent x86 cores.
Intel cores prior to family 6 are known not to be vulnerable, and so are
some Atoms and some Xeon Phi.
It assumes that older Cyrix, Centaur, etc. cores are immune.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa@csail.mit.edu>
Reviewed-by: Matt Helsley (VMware) <matt.helsley@gmail.com>
Reviewed-by: Alexey Makhalov <amakhalov@vmware.com>
Reviewed-by: Bo Gan <ganb@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 229bc19fd7aca4f37964af06e3583c1c8f36b5d6 upstream.
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3a498606bb04af603a46ebde8296040b2de350d1 ]
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9ba8376ce1e2cbf4ce44f7e4bee1d0648e10d594 ]
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244c0 ("ptp: Allow reassigning calibration pin function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df8ed346d4a806a6eef2db5924285e839604b3f9 ]
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a98302de19991d51e067b88750585203b2a3ab6 upstream.
Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.
rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.
In this situation, driver gives message "Firmware is not ready to run!".
Fixes: fe89707f0afa ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 676bcfece19f83621e905aa55b5ed2d45cc4f2d3 upstream.
t.qset_idx can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c:2286 cxgb_extension_ioctl()
warn: potential spectre issue 'adapter->msix_info'
Fix this by sanitizing t.qset_idx before using it to index
adapter->msix_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d412c31dae053bf30a1bc15582a9990df297a660 ]
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8f1f65882f07913157c44673af7ec0b308d03eb ]
Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when
we meet errors during ubuf allocation, the code does not check for
NULL before calling sockfd_put(), this will lead NULL
dereferencing. Fixing by checking sock pointer before.
Fixes: bab632d69ee4 ("vhost: vhost TX zero-copy support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0ee1f4734967af8321ecebaf9c74221ace34f2d5 ]
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb7858ba1102f82470a917e041fd23e6385c31be ]
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 12b03558cef6d655d0d394f5e98a6fd07c1f6c0f ]
After commit 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE
are friends"), sungem owners reported the infamous "eth0: hw csum failure"
message.
CHECKSUM_COMPLETE has in fact never worked for this driver, but this
was masked by the fact that upper stacks had to strip the FCS, and
therefore skb->ip_summed was set back to CHECKSUM_NONE before
my recent change.
Driver configures a number of bytes to skip when the chip computes
the checksum, and for some reason only half of the Ethernet header
was skipped.
Then a second problem is that we should strip the FCS by default,
unless the driver is updated to eventually support NETIF_F_RXFCS in
the future.
Finally, a driver should check if NETIF_F_RXCSUM feature is enabled
or not, so that the admin can turn off rx checksum if wanted.
Many thanks to Andreas Schwab and Mathieu Malaterre for their
help in debugging this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Mathieu Malaterre <malat@debian.org>
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 603b7bcff824740500ddfa001d7a7168b0b38542 ]
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ced9e191501e52b95e1b57b8e0db00943869eed0 ]
pool can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/zatm.c:1491 zatm_ioctl() warn: potential spectre issue
'zatm_dev->pool_info' (local cap)
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d59ad6eea82ef8df92b4109615a0dde9d8093e9 upstream.
If one of the later memory allocations in rypto4xx_build_pdr()
fails: dev->pdr (and/or) dev->pdr_uinfo wouldn't be freed.
crypto4xx_build_sdr() has the same issue with dev->sdr.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a728a196d253530f17da5c86dc7dfbe58c5f7094 upstream.
alg entries are only added to the list, after the registration
was successful. If the registration failed, it was never added
to the list in the first place.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6213c1f2ad54a964b77471690264ed685718928 upstream.
The DMA controller regs actually point to DMA channel 0, so the write to
ENETDMA_CFG_REG will actually modify a random DMA channel.
Since DMA controller registers do not exist on BCM6345, guard the write
with the usual check for dma_has_sram.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c86b846ce02f7e35d7234cf090b80553eba5389 upstream.
Check the return code of prepare_enable and change one last instance of
enable only to prepare_enable. Also properly disable and release the
clock in error paths and on remove for enetsw.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3349b6b3c373ac1fbfb040b810fcee5e2adc7e0 upstream.
syzbot is hitting WARN() triggered by memory allocation fault
injection [1] because loop module is calling sysfs_remove_group()
when sysfs_create_group() failed.
Fix this by remembering whether sysfs_create_group() succeeded.
[1] https://syzkaller.appspot.com/bug?id=3f86c0edf75c86d2633aeb9dd69eccc70bc7e90b
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+9f03168400f56df89dbc6f1751f4458fe739ff29@syzkaller.appspotmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renamed sysfs_ready -> sysfs_inited.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a8690ed6f5346f6738971892205e91d39b6b901 upstream.
In commit 357d23c811a7 ("Remove the obsolete libibcm library")
in rdma-core [1], we removed obsolete library which used the
/dev/infiniband/ucmX interface.
Following multiple syzkaller reports about non-sanitized
user input in the UCMA module, the short audit reveals the same
issues in UCM module too.
It is better to disable this interface in the kernel,
before syzkaller team invests time and energy to harden
this unused interface.
[1] https://github.com/linux-rdma/rdma-core/pull/279
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2ac838e4cd7e5e9891ecc094d626734b0245c99 upstream.
Refactor the validation code used in LOOP_SET_FD so it is also used in
LOOP_CHANGE_FD. Otherwise it is possible to construct a set of loop
devices that all refer to each other. This can lead to a infinite
loop in starting with "while (is_loop_device(f)) .." in loop_set_fd().
Fix this by refactoring out the validation code and using it for
LOOP_CHANGE_FD as well as LOOP_SET_FD.
Reported-by: syzbot+4349872271ece473a7c91190b68b4bac7c5dbc87@syzkaller.appspotmail.com
Reported-by: syzbot+40bd32c4d9a3cc12a339@syzkaller.appspotmail.com
Reported-by: syzbot+769c54e66f994b041be7@syzkaller.appspotmail.com
Reported-by: syzbot+0a89a9ce473936c57065@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b72717a20bba8bdd01b14c0460be7d15061cd6b upstream.
The code was mistakenly using the length of the page array memory instead
of the depth of the page array.
This would cause MR creation to fail in some cases.
Fixes: 8376b86de7d3 ("iw_cxgb4: Support the new memory registration API")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9547837bdccb4af127528b36a73377150658b4ac upstream.
The (1292:4745) Innomedia INNEX GENESIS/ATARI adapter needs
HID_QUIRK_MULTI_INPUT to split the device up into two controllers
instead of inputs from both being merged into one.
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 313db3d6488bb03b61b99de9dbca061f1fd838e1 upstream.
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bba57eddadda936c94b5dccf73787cb9e159d0a5 upstream.
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 794744abfffef8b1f3c0c8a4896177d6d13d653d upstream.
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1e255d60ae66a9f672ff9a207ee6cd8e33d2679 upstream.
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01b3cdfca263a17554f7b249d20a247b2a751521 upstream.
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd6777 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 367b160fe4717c14a2a978b6f9ffb75a7762d3ed upstream.
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e33eab9ded328ccc14308afa51b5be7cbe78d30b upstream.
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0c4 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 240630e61870e62e39a97225048f9945848fa5f5 upstream.
There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90d72ce079791399ac255c75728f3c9e747b093d upstream.
Embarrassingly, the recent fix introduced worse problem than it solved,
causing the balloon not to inflate. The VM informed the hypervisor that
the pages for lock/unlock are sitting in the wrong address, as it used
the page that is used the uninitialized page variable.
Fixes: b23220fe054e9 ("vmw_balloon: fixing double free when batching mode is off")
Cc: stable@vger.kernel.org
Reviewed-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0341fc1981a950c1e902ab901e98f60e0e243f3 upstream.
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1376b0a2160319125c3a2822e8c09bd283cd8141 upstream.
There is a '>' vs '<' typo so this loop is a no-op.
Fixes: d35dcc89fc93 ("staging: comedi: quatech_daqp_cs: fix daqp_ao_insn_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79ca484b613041ca223f74b34608bb6f5221724b upstream.
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45f75b8a919a4255f52df454f1ffdee0e42443b2 upstream.
For the word write functions it is retried for error.
But it is not implemented to retry for the erase functions.
To make sure for the erase functions change to retry as same.
This is needed to prevent the flash erase error caused only once.
It was caused by the error case of chip_good() in the do_erase_oneblock().
Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G.
But the error issue behavior is not able to reproduce at this moment.
The flash controller is parallel Flash interface integrated on BCM53003.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85a82e28b023de9b259a86824afbd6ba07bd6475 upstream.
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d12067f428c037b4575aaeb2be00847fc214c24a upstream.
dm_bufio_shrink_count() is called from do_shrink_slab to find out how many
freeable objects are there. The reported value doesn't have to be precise,
so we don't need to take the dm-bufio lock.
Suggested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f77f244d8ec28e3a0a81240ffac7d626390060c upstream.
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41c73a49df31151f4ff868f28fe4f129f113fa2c upstream.
If the first allocation attempt using GFP_NOWAIT fails, drop the lock
and retry using GFP_NOIO allocation (lock is dropped because the
allocation can take some time).
Note that we won't do GFP_NOIO allocation when we loop for the second
time, because the lock shouldn't be dropped between __wait_for_free_buffer
and __get_unclaimed_buffer.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ea61cac0b1ad0c09022f39fd97e9b99a2cfc2dc upstream.
We've seen in-field reports showing _lots_ (18 in one case, 41 in
another) of tasks all sitting there blocked on:
mutex_lock+0x4c/0x68
dm_bufio_shrink_count+0x38/0x78
shrink_slab.part.54.constprop.65+0x100/0x464
shrink_zone+0xa8/0x198
In the two cases analyzed, we see one task that looks like this:
Workqueue: kverityd verity_prefetch_io
__switch_to+0x9c/0xa8
__schedule+0x440/0x6d8
schedule+0x94/0xb4
schedule_timeout+0x204/0x27c
schedule_timeout_uninterruptible+0x44/0x50
wait_iff_congested+0x9c/0x1f0
shrink_inactive_list+0x3a0/0x4cc
shrink_lruvec+0x418/0x5cc
shrink_zone+0x88/0x198
try_to_free_pages+0x51c/0x588
__alloc_pages_nodemask+0x648/0xa88
__get_free_pages+0x34/0x7c
alloc_buffer+0xa4/0x144
__bufio_new+0x84/0x278
dm_bufio_prefetch+0x9c/0x154
verity_prefetch_io+0xe8/0x10c
process_one_work+0x240/0x424
worker_thread+0x2fc/0x424
kthread+0x10c/0x114
...and that looks to be the one holding the mutex.
The problem has been reproduced on fairly easily:
0. Be running Chrome OS w/ verity enabled on the root filesystem
1. Pick test patch: http://crosreview.com/412360
2. Install launchBalloons.sh and balloon.arm from
http://crbug.com/468342
...that's just a memory stress test app.
3. On a 4GB rk3399 machine, run
nice ./launchBalloons.sh 4 900 100000
...that tries to eat 4 * 900 MB of memory and keep accessing.
4. Login to the Chrome web browser and restore many tabs
With that, I've seen printouts like:
DOUG: long bufio 90758 ms
...and stack trace always show's we're in dm_bufio_prefetch().
The problem is that we try to allocate memory with GFP_NOIO while
we're holding the dm_bufio lock. Instead we should be using
GFP_NOWAIT. Using GFP_NOIO can cause us to sleep while holding the
lock and that causes the above problems.
The current behavior explained by David Rientjes:
It will still try reclaim initially because __GFP_WAIT (or
__GFP_KSWAPD_RECLAIM) is set by GFP_NOIO. This is the cause of
contention on dm_bufio_lock() that the thread holds. You want to
pass GFP_NOWAIT instead of GFP_NOIO to alloc_buffer() when holding a
mutex that can be contended by a concurrent slab shrinker (if
count_objects didn't use a trylock, this pattern would trivially
deadlock).
This change significantly increases responsiveness of the system while
in this state. It makes a real difference because it unblocks kswapd.
In the bug report analyzed, kswapd was hung:
kswapd0 D ffffffc000204fd8 0 72 2 0x00000000
Call trace:
[<ffffffc000204fd8>] __switch_to+0x9c/0xa8
[<ffffffc00090b794>] __schedule+0x440/0x6d8
[<ffffffc00090bac0>] schedule+0x94/0xb4
[<ffffffc00090be44>] schedule_preempt_disabled+0x28/0x44
[<ffffffc00090d900>] __mutex_lock_slowpath+0x120/0x1ac
[<ffffffc00090d9d8>] mutex_lock+0x4c/0x68
[<ffffffc000708e7c>] dm_bufio_shrink_count+0x38/0x78
[<ffffffc00030b268>] shrink_slab.part.54.constprop.65+0x100/0x464
[<ffffffc00030dbd8>] shrink_zone+0xa8/0x198
[<ffffffc00030e578>] balance_pgdat+0x328/0x508
[<ffffffc00030eb7c>] kswapd+0x424/0x51c
[<ffffffc00023f06c>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
By unblocking kswapd memory pressure should be reduced.
Suggested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ee9bc12342cf546313d300808ff47d7dbb8e7db upstream.
The cx25840 driver currently configures 885, 887, and 888 using
default divisors for each chip. This check to see if the cx23885
driver has passed the cx25840 a non-default clock rate for a
specific chip. If a cx23885 board has left clk_freq at 0, the
clock default values will be used to configure the PLLs.
This patch only has effect on 888 boards who set clk_freq to 25M.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 717adfdaf14704fd3ec7fa2c04520c0723247eac upstream.
If our length is greater than the size of the buffer, we
overflow the buffer
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
