| Age | Commit message (Collapse) | Author |
|---|
|
All the wakeup sources we possibly want will go through the interrupt
controller, so the parent IRQ must not be masked during suspend, or
there won't be any way to wake up the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200819180602.136969-1-paul@crapouillou.net
|
|
mistake
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
|
|
helperse
It has become obvious that switching a number of irqchip drivers
to being platform drivers without considering the platform was a
mistake. We have multiple reports of end-point drivers not
probing because the irqchip driver isn't there yet, breaking
the expectations of the users.
This patch reverts:
920ecb8c35cb ("irqchip/mtk-cirq: Convert to a platform driver")
f97dbf48ca43 ("irqchip/mtk-sysirq: Convert to a platform driver")
5be57099d445 ("irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros")
95bf9305d2e3 ("irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module")
and leave QCOM PDC, MTK sysrq and cirq drivers as built-in, special purpose
drivers for the time being until we have worked out a better solution.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reported-by: Frank Wunderlich <linux@fw-web.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/93debe6a0308b66d3f307af67ba7ec2c@kernel.org
|
|
When probing an interrupt controller that is behind a parent,
we try to check whether the parent domain is available as
an indication that we can actually try to probe.
Unfortunately, we are checking this with the firmware node of
the about to be probed device, not the parent. This is obviously
bound to fail.
Instead, use the parent node.
Fixes: f8410e626569 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Driver assumes that Interrupt parent to Interrupt Aggregator is always
Interrupt router. This is not true always and GIC can be a parent to
Interrupt Aggregator. Update the driver to detect the parent and request
the parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-11-lokeshvutla@ti.com
|
|
Even though DT doesn't make active use of id field in platform_device, we cannot
hijack it to store TISCI device id. So create a field in struct ti_sci_inta
for storing TISCI id and drop usage of id field in platform_device.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-10-lokeshvutla@ti.com
|
|
Driver assumes that Interrupt parent to Interrupt router is always GIC.
This is not true always and an Interrupt Router can be a parent to
Interrupt Router. Update the driver to detect the parent and request the
parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-7-lokeshvutla@ti.com
|
|
With SYSFW ABI 3.0 changes, interrupts coming out of an interrupt
controller is identified by a type and it is consistent across SoCs.
Similarly global events for Interrupt aggregator. So add an API to get
resource range using a resource type.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200806074826.24607-4-lokeshvutla@ti.com
|
|
struct ti_sci_rm_type_map is no longer used. Drop its definition and its
declarations.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200806074826.24607-3-lokeshvutla@ti.com
|
|
With ABI 3.0, sysfw deprecated special resource types used for AM65x
SoC. Instead started using device id as resource type similar to the
convention used in J721E SOC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200806074826.24607-2-lokeshvutla@ti.com
|
|
Pull block fixes from Jens Axboe:
"A few fixes on the block side of things:
- Discard granularity fix (Coly)
- rnbd cleanups (Guoqing)
- md error handling fix (Dan)
- md sysfs fix (Junxiao)
- Fix flush request accounting, which caused an IO slowdown for some
configurations (Ming)
- Properly propagate loop flag for partition scanning (Lennart)"
* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
block: fix double account of flush request's driver tag
loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
rnbd: no need to set bi_end_io in rnbd_bio_map_kern
rnbd: remove rnbd_dev_submit_io
md-cluster: Fix potential error pointer dereference in resize_bitmaps()
block: check queue's limits.discard_granularity in __blkdev_issue_discard()
md: get sysfs entry after redundancy attr group create
|
|
Pull arch/sh updates from Rich Felker:
"Cleanup, SECCOMP_FILTER support, message printing fixes, and other
changes to arch/sh"
* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
sh: landisk: Add missing initialization of sh_io_port_base
sh: bring syscall_set_return_value in line with other architectures
sh: Add SECCOMP_FILTER
sh: Rearrange blocks in entry-common.S
sh: switch to copy_thread_tls()
sh: use the generic dma coherent remap allocator
sh: don't allow non-coherent DMA for NOMMU
dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
sh: unexport register_trapped_io and match_trapped_io_handler
sh: don't include <asm/io_trapped.h> in <asm/io.h>
sh: move the ioremap implementation out of line
sh: move ioremap_fixed details out of <asm/io.h>
sh: remove __KERNEL__ ifdefs from non-UAPI headers
sh: sort the selects for SUPERH alphabetically
sh: remove -Werror from Makefiles
sh: Replace HTTP links with HTTPS ones
arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
sh: stacktrace: Remove stacktrace_ops.stack()
sh: machvec: Modernize printing of kernel messages
sh: pci: Modernize printing of kernel messages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull edac fix from Tony Luck:
"Fix for the ie31200 driver that missed the first pull"
* tag 'edac_updates_for_5.9_pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/ie31200: Fallback if host bridge device is already initialized
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen)"
* tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
clk: x86: Support RV architecture
ACPI: APD: Add a fmw property is_raven
clk: x86: Change name from ST to FCH
ACPI: APD: Change name from ST to FCH
i2c: designware: Add device HID for Hygon I2C controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull one more power management update from Rafael Wysocki:
"Modify the intel_pstate driver to allow it to work in the passive mode
with hardware-managed P-states (HWP) enabled"
* tag 'pm-5.9-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Implement passive mode with HWP enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
|
|
Merge more updates from Andrew Morton:
"Subsystems affected by this patch series: mm/hotfixes, lz4, exec,
mailmap, mm/thp, autofs, sysctl, mm/kmemleak, mm/misc and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
virtio: pci: constify ioreadX() iomem argument (as in generic implementation)
ntb: intel: constify ioreadX() iomem argument (as in generic implementation)
rtl818x: constify ioreadX() iomem argument (as in generic implementation)
iomap: constify ioreadX() iomem argument (as in generic implementation)
sh: use generic strncpy()
sh: clkfwk: remove r8/r16/r32
include/asm-generic/vmlinux.lds.h: align ro_after_init
mm: annotate a data race in page_zonenum()
mm/swap.c: annotate data races for lru_rotate_pvecs
mm/rmap: annotate a data race at tlb_flush_batched
mm/mempool: fix a data race in mempool_free()
mm/list_lru: fix a data race in list_lru_count_one
mm/memcontrol: fix a data race in scan count
mm/page_counter: fix various data races at memsw
mm/swapfile: fix and annotate various data races
mm/filemap.c: fix a data race in filemap_fault()
mm/swap_state: mark various intentional data races
mm/page_io: mark various intentional data races
mm/frontswap: mark various intentional data races
mm/kmemleak: silence KCSAN splats in checksum
...
|
|
The ioreadX() helpers have inconsistent interface. On some architectures
void *__iomem address argument is a pointer to const, on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200709072837.5869-5-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ioreadX() helpers have inconsistent interface. On some architectures
void *__iomem address argument is a pointer to const, on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200709072837.5869-4-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ioreadX() helpers have inconsistent interface. On some architectures
void *__iomem address argument is a pointer to const, on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200709072837.5869-3-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "iomap: Constify ioreadX() iomem argument", v3.
The ioread8/16/32() and others have inconsistent interface among the
architectures: some taking address as const, some not.
It seems there is nothing really stopping all of them to take pointer to
const.
This patch (of 4):
The ioreadX() and ioreadX_rep() helpers have inconsistent interface. On
some architectures void *__iomem address argument is a pointer to const,
on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
[krzk@kernel.org: sh: clk: fix assignment from incompatible pointer type for ioreadX()]
Link: http://lkml.kernel.org/r/20200723082017.24053-1-krzk@kernel.org
[akpm@linux-foundation.org: fix drivers/mailbox/bcm-pdc-mailbox.c]
Link: http://lkml.kernel.org/r/202007132209.Rxmv4QyS%25lkp@intel.com
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/20200709072837.5869-1-krzk@kernel.org
Link: http://lkml.kernel.org/r/20200709072837.5869-2-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SH will get below warning
${LINUX}/drivers/sh/clk/cpg.c: In function 'r8':
${LINUX}/drivers/sh/clk/cpg.c:41:17: warning: passing argument 1 of 'ioread8'
discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
return ioread8(addr);
^~~~
In file included from ${LINUX}/arch/sh/include/asm/io.h:21,
from ${LINUX}/include/linux/io.h:13,
from ${LINUX}/drivers/sh/clk/cpg.c:14:
${LINUX}/include/asm-generic/iomap.h:29:29: note: expected 'void *' but
argument is of type 'const void *'
extern unsigned int ioread8(void __iomem *);
^~~~~~~~~~~~~~
We don't need "const" for r8/r16/r32. And we don't need r8/r16/r32
themselvs. This patch cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Modra <amodra@gmail.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Chen Zhou <chenzhou10@huawei.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Romain Naour <romain.naour@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
X-MARC-Message: https://marc.info/?l=linux-renesas-soc&m=157852973916903
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This function returns the number of bytes in a THP. It is like
page_size(), but compiles to just PAGE_SIZE if CONFIG_TRANSPARENT_HUGEPAGE
is disabled.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Link: http://lkml.kernel.org/r/20200629151959.15779-5-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As of commit 37744feebc086908 ("sh: remove sh5 support"), support for
the SH5-based Cayman platform can no longer be selected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
Pull more SCSI updates from James Bottomley:
"This is the set of patches which arrived too late to stabilise in
-next for the first pull.
It's really just an lpfc driver update and an assortment of minor
fixes, all in drivers. The only core update is to the zone block
device driver, which isn't the one most people use"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Update lpfc version to 12.8.0.3
scsi: lpfc: Fix LUN loss after cable pull
scsi: lpfc: Fix validation of bsg reply lengths
scsi: lpfc: Fix retry of PRLI when status indicates its unsupported
scsi: lpfc: Fix oops when unloading driver while running mds diags
scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter
scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value
scsi: lpfc: Fix FCoE speed reporting
scsi: lpfc: Add missing misc_deregister() for lpfc_init()
scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport
scsi: scsi_transport_sas: Add spaces around binary operator "|"
scsi: sd_zbc: Improve zone revalidation
scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases
scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del()
scsi: target: Make iscsit_register_transport() return void
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- Remove support for running as 32-bit Xen PV-guest.
32-bit PV guests are rarely used, are lacking security fixes for
Meltdown, and can be easily replaced by PVH mode. Another series for
doing more cleanup will follow soon (removal of 32-bit-only pvops
functionality).
- Fixes and additional features for the Xen display frontend driver.
* tag 'for-linus-5.9-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drm/xen-front: Pass dumb buffer data offset to the backend
xen: Sync up with the canonical protocol definition in Xen
drm/xen-front: Add YUYV to supported formats
drm/xen-front: Fix misused IS_ERR_OR_NULL checks
xen/gntdev: Fix dmabuf import with non-zero sgt offset
x86/xen: drop tests for highmem in pv code
x86/xen: eliminate xen-asm_64.S
x86/xen: remove 32-bit Xen PV guest support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v fixes from Wei Liu:
- fix oops reporting on Hyper-V
- make objtool happy
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Make hv_setup_sched_clock inline
Drivers: hv: vmbus: Only notify Hyper-V for die events that are oops
|
|
* pm-cpufreq:
cpufreq: intel_pstate: Implement passive mode with HWP enabled
|
|
Pull networking fixes from David Miller:
"Some merge window fallout, some longer term fixes:
1) Handle headroom properly in lapbether and x25_asy drivers, from
Xie He.
2) Fetch MAC address from correct r8152 device node, from Thierry
Reding.
3) In the sw kTLS path we should allow MSG_CMSG_COMPAT in sendmsg,
from Rouven Czerwinski.
4) Correct fdputs in socket layer, from Miaohe Lin.
5) Revert troublesome sockptr_t optimization, from Christoph Hellwig.
6) Fix TCP TFO key reading on big endian, from Jason Baron.
7) Missing CAP_NET_RAW check in nfc, from Qingyu Li.
8) Fix inet fastreuse optimization with tproxy sockets, from Tim
Froidcoeur.
9) Fix 64-bit divide in new SFC driver, from Edward Cree.
10) Add a tracepoint for prandom_u32 so that we can more easily
perform usage analysis. From Eric Dumazet.
11) Fix rwlock imbalance in AF_PACKET, from John Ogness"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
net: openvswitch: introduce common code for flushing flows
af_packet: TPACKET_V3: fix fill status rwlock imbalance
random32: add a tracepoint for prandom_u32()
Revert "ipv4: tunnel: fix compilation on ARCH=um"
net: accept an empty mask in /sys/class/net/*/queues/rx-*/rps_cpus
net: ethernet: stmmac: Disable hardware multicast filter
net: stmmac: dwmac1000: provide multicast filter fallback
ipv4: tunnel: fix compilation on ARCH=um
vsock: fix potential null pointer dereference in vsock_poll()
sfc: fix ef100 design-param checking
net: initialize fastreuse on inet_inherit_port
net: refactor bind_bucket fastreuse into helper
net: phy: marvell10g: fix null pointer dereference
net: Fix potential memory leak in proto_register()
net: qcom/emac: add missed clk_disable_unprepare in error path of emac_clks_phase1_init
ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()
net/nfc/rawsock.c: add CAP_NET_RAW check.
hinic: fix strncpy output truncated compile warnings
drivers/net/wan/x25_asy: Added needed_headroom and a skb->len check
net/tls: Fix kmap usage
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- bus recovery can now be given a pinctrl handle and the I2C core will
do all the steps to switch to/from GPIO which can save quite some
boilerplate code from drivers
- "fallthrough" conversion
- driver updates, mostly ID additions
* 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits)
i2c: iproc: fix race between client unreg and isr
i2c: eg20t: use generic power management
i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume
i2c: mediatek: Fix i2c_spec_values description
i2c: mediatek: Add i2c compatible for MediaTek MT8192
dt-bindings: i2c: update bindings for MT8192 SoC
i2c: mediatek: Add access to more than 8GB dram in i2c driver
i2c: mediatek: Add apdma sync in i2c driver
i2c: i801: Add support for Intel Tiger Lake PCH-H
i2c: i801: Add support for Intel Emmitsburg PCH
i2c: bcm2835: Replace HTTP links with HTTPS ones
Documentation: i2c: dev: 'block process call' is supported
i2c: at91: Move to generic GPIO bus recovery
i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs
i2c: core: add generic I2C GPIO recovery
dt-bindings: i2c: add generic properties for GPIO bus recovery
i2c: rcar: avoid race when unregistering slave
i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
i2c: tegra: Fix runtime resume to re-init VI I2C
i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- Allow s390 debug feature to handle finally more than 256 CPU numbers,
instead of truncating the most significant bits.
- Improve THP splitting required by qemu processes by making use of
walk_page_vma() instead of calling follow_page() for every single
page within each vma.
- Add missing ZCRYPT dependency to VFIO_AP to fix potential compile
problems.
- Remove not required select CLOCKSOURCE_VALIDATE_LAST_CYCLE again.
- Set node distance to LOCAL_DISTANCE instead of 0, since e.g. libnuma
translates a node distance of 0 to "no NUMA support available".
- Couple of other minor fixes and improvements.
* tag 's390-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/numa: move code to arch/s390/kernel
s390/time: remove select CLOCKSOURCE_VALIDATE_LAST_CYCLE again
s390/debug: debug feature version 3
s390/Kconfig: add missing ZCRYPT dependency to VFIO_AP
s390/numa: set node distance to LOCAL_DISTANCE
s390/pkey: remove redundant variable initialization
s390/test_unwind: fix possible memleak in test_unwind()
s390/gmap: improve THP splitting
s390/atomic: circumvent gcc 10 build regression
|
|
While importing a dmabuf it is possible that the data of the buffer
is put with offset which is indicated by the SGT offset.
Respect the offset value and forward it to the backend.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Add YUYV to supported formats, so the frontend can work with the
formats used by cameras and other HW.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20200813062113.11030-4-andr2000@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The patch c575b7eeb89f: "drm/xen-front: Add support for Xen PV
display frontend" from Apr 3, 2018, leads to the following static
checker warning:
drivers/gpu/drm/xen/xen_drm_front_gem.c:140 xen_drm_front_gem_create()
warn: passing zero to 'ERR_CAST'
drivers/gpu/drm/xen/xen_drm_front_gem.c
133 struct drm_gem_object *xen_drm_front_gem_create(struct drm_device *dev,
134 size_t size)
135 {
136 struct xen_gem_object *xen_obj;
137
138 xen_obj = gem_create(dev, size);
139 if (IS_ERR_OR_NULL(xen_obj))
140 return ERR_CAST(xen_obj);
Fix this and the rest of misused places with IS_ERR_OR_NULL in the
driver.
Fixes: c575b7eeb89f: "drm/xen-front: Add support for Xen PV display frontend"
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813062113.11030-3-andr2000@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
It is possible that the scatter-gather table during dmabuf import has
non-zero offset of the data, but user-space doesn't expect that.
Fix this by failing the import, so user-space doesn't access wrong data.
Fixes: bf8dc55b1358 ("xen/gntdev: Implement dma-buf import functionality")
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813062113.11030-2-andr2000@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The DT node full name is currently being used in regmap_config
which in turn is used to create the regmap debugfs directories.
This name however is not guaranteed to be unique and the regmap
debugfs registration can fail in the cases where the syscon nodes
have the same unit-address but are present in different DT node
hierarchies. Replace this logic using the syscon reg resource
address instead (inspired from logic used while creating platform
devices) to ensure a unique name is given for each syscon.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The event handler loop must be run with interrupts disabled.
Otherwise we will have a warning:
[ 1970.785649] irq 31 handler lineevent_irq_handler+0x0/0x20 enabled interrupts
[ 1970.792739] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x162/0x170
[ 1970.860732] RIP: 0010:__handle_irq_event_percpu+0x162/0x170
...
[ 1970.946994] Call Trace:
[ 1970.949446] <IRQ>
[ 1970.951471] handle_irq_event_percpu+0x2c/0x80
[ 1970.955921] handle_irq_event+0x23/0x43
[ 1970.959766] handle_simple_irq+0x57/0x70
[ 1970.963695] generic_handle_irq+0x42/0x50
[ 1970.967717] dln2_rx+0xc1/0x210 [dln2]
[ 1970.971479] ? usb_hcd_unmap_urb_for_dma+0xa6/0x1c0
[ 1970.976362] __usb_hcd_giveback_urb+0x77/0xe0
[ 1970.980727] usb_giveback_urb_bh+0x8e/0xe0
[ 1970.984837] tasklet_action_common.isra.0+0x4a/0xe0
...
Recently xHCI driver switched to tasklets in the commit 36dc01657b49
("usb: host: xhci: Support running urb giveback in tasklet context").
The handle_irq_event_* functions are expected to be called with interrupts
disabled and they rightfully complain here because we run in tasklet context
with interrupts enabled.
Use a event spinlock to protect event handler from being interrupted.
Note, that there are only two users of this GPIO and ADC drivers and both of
them are using generic_handle_irq() which makes above happen.
Fixes: 338a12814297 ("mfd: Add support for Diolan DLN-2 devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The current unbinding process for Madera has some issues. The trouble
is runtime PM is disabled as the first step of the process, but
some of the drivers release IRQs causing regmap IRQ to issue a
runtime get which fails. To allow runtime PM to remain enabled during
mfd_remove_devices, the DCVDD regulator must remain available. In
the case of external DCVDD's this is simple, the regulator can simply
be disabled/put after the call to mfd_remove_devices. However, in
the case of an internally supplied DCVDD the regulator needs to be
released after the other MFD children depending on it.
Use the new MFD mfd_remove_devices_late functionality to split
the DCVDD regulator off from the other drivers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently, the only way to remove MFD children is with a call to
mfd_remove_devices, which will remove all the children. Under
some circumstances it is useful to remove only a subset of the
child devices. For example if some additional clean up is required
between removal of certain child devices.
To accomplish this a level field is added to mfd_cell, the normal
mfd_remove_devices is modified to not remove devices that are set
to a higher level and a corresponding mfd_remove_devices_late
function is added to remove those children.
See further discussion at:
https://lore.kernel.org/lkml/20200616075834.GF2608702@dell/
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
intel_scu_ipc_dev_iowrite8()
Simplify the return expression.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The variable current_bits is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Battery status changes dynamically, so the corresponding registers
need to be considered volatile. Affected registers are:
- fuel gauge
- battery status
- battery interrupt
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The restart handler is executed during the shutdown phase which is
atomic/irq-less. The i2c framework supports atomic transfers since
commit 63b96983a5dd ("i2c: core: introduce callbacks for atomic
transfers") to address this use case. Using i2c regmap in that
situation is not allowed:
[ 165.177465] [ BUG: Invalid wait context ]
[ 165.181479] 5.8.0-rc3-00003-g0e9088558027-dirty #11 Not tainted
[ 165.187400] -----------------------------
[ 165.191410] systemd-shutdow/1 is trying to lock:
[ 165.196030] d85b4438 (rn5t618:170:(&rn5t618_regmap_config)->lock){+.+.}-{3:3}, at: regmap_update_bits_base+0x30/0x70
[ 165.206573] other info that might help us debug this:
[ 165.211625] context-{4:4}
[ 165.214248] 2 locks held by systemd-shutdow/1:
[ 165.218691] #0: c131c47c (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x90/0x204
[ 165.227405] #1: c131efb4 (rcu_read_lock){....}-{1:2}, at: __atomic_notifier_call_chain+0x0/0x118
[ 165.236288] stack backtrace:
[ 165.239174] CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.8.0-rc3-00003-g0e9088558027-dirty #11
[ 165.248220] Hardware name: Freescale i.MX6 SoloLite (Device Tree)
[ 165.254330] [<c0112110>] (unwind_backtrace) from [<c010bfa0>] (show_stack+0x10/0x14)
[ 165.262084] [<c010bfa0>] (show_stack) from [<c058093c>] (dump_stack+0xe8/0x120)
[ 165.269407] [<c058093c>] (dump_stack) from [<c01835a4>] (__lock_acquire+0x81c/0x2ca0)
[ 165.277246] [<c01835a4>] (__lock_acquire) from [<c0186344>] (lock_acquire+0xe4/0x490)
[ 165.285090] [<c0186344>] (lock_acquire) from [<c0c98638>] (__mutex_lock+0x74/0x954)
[ 165.292756] [<c0c98638>] (__mutex_lock) from [<c0c98f34>] (mutex_lock_nested+0x1c/0x24)
[ 165.300769] [<c0c98f34>] (mutex_lock_nested) from [<c07593ec>] (regmap_update_bits_base+0x30/0x70)
[ 165.309741] [<c07593ec>] (regmap_update_bits_base) from [<c076b838>] (rn5t618_trigger_poweroff_sequence+0x34/0x64)
[ 165.320097] [<c076b838>] (rn5t618_trigger_poweroff_sequence) from [<c076b874>] (rn5t618_restart+0xc/0x2c)
[ 165.329669] [<c076b874>] (rn5t618_restart) from [<c01514f8>] (notifier_call_chain+0x48/0x80)
[ 165.338113] [<c01514f8>] (notifier_call_chain) from [<c01516a8>] (__atomic_notifier_call_chain+0x70/0x118)
[ 165.347770] [<c01516a8>] (__atomic_notifier_call_chain) from [<c0151768>] (atomic_notifier_call_chain+0x18/0x20)
[ 165.357949] [<c0151768>] (atomic_notifier_call_chain) from [<c010a828>] (machine_restart+0x68/0x80)
[ 165.367001] [<c010a828>] (machine_restart) from [<c0153224>] (__do_sys_reboot+0x11c/0x204)
[ 165.375272] [<c0153224>] (__do_sys_reboot) from [<c0100080>] (ret_fast_syscall+0x0/0x28)
[ 165.383364] Exception stack(0xd80a5fa8 to 0xd80a5ff0)
[ 165.388420] 5fa0: 00406948 00000000 fee1dead 28121969 01234567 73299b00
[ 165.396602] 5fc0: 00406948 00000000 00000000 00000058 be91abc8 00000000 be91ab60 004056f8
[ 165.404781] 5fe0: 00000058 be91aabc b6ed4d45 b6e56746
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
drivers/mfd/kempld-core.c: In function 'kempld_register_cells_generic':
drivers/mfd/kempld-core.c:105:13: error: assignment of read-only location 'devs[i++]'
105 | devs[i++] = kempld_devs[KEMPLD_I2C];
| ^
drivers/mfd/kempld-core.c:108:13: error: assignment of read-only location 'devs[i++]'
108 | devs[i++] = kempld_devs[KEMPLD_WDT];
| ^
drivers/mfd/kempld-core.c:111:13: error: assignment of read-only location 'devs[i++]'
111 | devs[i++] = kempld_devs[KEMPLD_GPIO];
| ^
drivers/mfd/kempld-core.c:114:13: error: assignment of read-only location 'devs[i++]'
114 | devs[i++] = kempld_devs[KEMPLD_UART];
| ^
Fixes: e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The AXP803 can be used both using the RSB proprietary bus, or a more
traditional I2C bus.
Let's add that possibility.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This update adds new regmap tables to support the latest DA silicon
which will automatically be selected based on the chip and variant
information read from the device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The current implementation performs checking in the i2c_probe()
function of the variant_code but does this immediately after the
containing struct has been initialised as all zero. This means the
check for variant code will always default to using the BB tables
and will never select AD. The variant code is subsequently set
by device_init() and later used by the RTC so really it's a little
fortunate this mismatch works.
This update adds raw I2C read access functionality to read the chip
and variant/revision information (common to all revisions) so that
it can subsequently correctly choose the proper regmap tables for
real initialisation.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Otherwise we get spammed with errors on resume after rtcwake:
cpcap-core spi0.0: Failed to read IRQ status: -108
Note that rtcwake is still capable of waking up the system with
this patch.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
