| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 8a7cb245cf28cb3e541e0d6c8624b95d079e155b ]
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52bfcdd87e83d9e69d22da5f26b1512ffc81deed ]
An sk_buff is allocated to send a flow control message, but it's not
sent in all cases: in case the state is not appropiate to send it or if
it can't be enqueued.
In the first of these 2 cases, the sk_buff was discarded but not freed,
producing a memory leak.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da91ece226729c76f60708efc275ebd4716ad089 ]
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 16e9b3e58bc3fce7391539e0eb3fd167cbf9951f ]
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a20342572f66c5b20a1ee680f5ac0a13703748f ]
Nothing can stop a host from submitting invalid commands. The target
just needs to respond with an appropriate status, but that's not a
target error. Demote invalid command messages to the debug level so
these events don't spam the kernel logs.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b117b3964f38a988cb79825950dbd607c02237f3 ]
Writing to dcefclk causes the gpu to become unresponsive, and requires a reboot.
Patch ignores a .force_clk_levels(SMU_DCEFCLK) call and issues an
info message.
Signed-off-by: Darren Powell <darren.powell@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9814b55cde0588b6d9bc496cee43f87316cbc6f1 ]
If tcmu_handle_completions() finds an invalid cmd_id while looping over cmd
responses from userspace it sets TCMU_DEV_BIT_BROKEN and breaks the
loop. This means that it does further handling for the tcmu device.
Skip that handling by replacing 'break' with 'return'.
Additionally change tcmu_handle_completions() from unsigned int to bool,
since the value used in return already is bool.
Link: https://lore.kernel.org/r/20210423150123.24468-1-bostroesser@gmail.com
Signed-off-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1364711359f3ced054bda9920477c8bf93b74c5 ]
In devloss timer handler and in backend calls to terminate remote port I/O,
there is logic to walk through all active IOCBs and validate them to
potentially trigger an abort request. This logic is causing illegal memory
accesses which leads to a crash. Abort IOCBs, which may be on the list, do
not have an associated lpfc_io_buf struct. The driver is trying to map an
lpfc_io_buf struct on the IOCB and which results in a bogus address thus
the issue.
Fix by skipping over ABORT IOCBs (CLOSE IOCBs are ABORTS that don't send
ABTS) in the IOCB scan logic.
Link: https://lore.kernel.org/r/20210421234433.102079-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5bb32f57bf3a30ed03be51f7be0840325ba8b4a ]
There are certain transitional situations where the dp_mode field in the
PD_CONTROL response might not be populated with the right DP pin
assignment value yet. Add a check for that to avoid sending an invalid
value to the Type C mode switch.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421042108.2002-1-pmalani@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
stuck state
[ Upstream commit e479187748a8f151a85116a7091c599b121fdea5 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 65299e8bfb24774e6340e93ae49f6626598917c8 ]
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5859c926d1f052ee61b5815b14658875c14f6243 ]
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3bbfd319034ddce59e023837a4aa11439460509b ]
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com
Signed-off-by: Feilong Lin <linfeilong@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e970dcc4bd8e0a1376e794fc81d41d0fc98262dd ]
When the driver is compiled as a module and loaded if we try to unload
it, the Kernel shows a crash log. This Kernel crash is due to the
dma_async_device_unregister() call done after deleting the channels,
this patch fixes this issue.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/4aa850c035cf7ee488f1d3fb6dee0e37be0dce0a.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 16f7ae5906dfbeff54f74ec75d0563bb3a87ab0b ]
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f6925b3e8da0dbbb52447ca8a8b42b371aac7db ]
Xuan Zhuo reported that commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") brought a ~10% performance drop.
The reason for the performance drop was that GRO was forced
to chain sk_buff (using skb_shinfo(skb)->frag_list), which
uses more memory but also cause packet consumers to go over
a lot of overhead handling all the tiny skbs.
It turns out that virtio_net page_to_skb() has a wrong strategy :
It allocates skbs with GOOD_COPY_LEN (128) bytes in skb->head, then
copies 128 bytes from the page, before feeding the packet to GRO stack.
This was suboptimal before commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") because GRO was using 2 frags per MSS,
meaning we were not packing MSS with 100% efficiency.
Fix is to pull only the ethernet header in page_to_skb()
Then, we change virtio_net_hdr_to_skb() to pull the missing
headers, instead of assuming they were already pulled by callers.
This fixes the performance regression, but could also allow virtio_net
to accept packets with more than 128bytes of headers.
Many thanks to Xuan Zhuo for his report, and his tests/help.
Fixes: 3226b158e67c ("net: avoid 32 x truesize under-estimation for tiny skbs")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://www.spinics.net/lists/netdev/msg731397.html
Co-Developed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5ee7d4c7fbc9d3119a20b1c77d34003d1f82ac26 upstream.
gcc-11 complains about a prototype declaration that is different
from the function definition:
drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}
62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}
64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~
Change the definition to make them match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea8146c6845799142aa4ee2660741c215e340cdf upstream.
Fix the gcc warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604467444-23043-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8460f6003a1d2633737b89c4f69d6f4c0c7c65a3 upstream.
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40cc3a80bb42587db1e6ae21d6f3090582d33e89 upstream.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
Fixes: e8d31c204e36 ("kgdb: add kgdb internal test suite")
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164308.827846-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7909a590eba6d021f104958857cbc4f0089daceb upstream.
gcc-11 with KASAN on 32-bit arm produces a warning about a function
that needs a lot of stack space:
drivers/net/wireless/cisco/airo.c: In function 'setup_card.constprop':
drivers/net/wireless/cisco/airo.c:3960:1: error: the frame size of 1512 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Most of this is from a single large structure that could be dynamically
allocated or moved into the per-device structure. However, as the callers
all seem to have a fairly well bounded call chain, the easiest change
is to pull out the part of the function that needs the large variables
into a separate function and mark that as noinline_for_stack. This does
not reduce the total stack usage, but it gets rid of the warning and
requires minimal changes otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323131634.2669455-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fec4d42724a1bf3dcba52307e55375fdb967b852 upstream.
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 53fe2a30bc168db9700e00206d991ff934973cf1 upstream.
Do not call nvme_configure_apst when the controller is not live, given
that nvme_configure_apst will fail due the lack of an admin queue when
the controller is being torn down and nvme_set_latency_tolerance is
called from dev_pm_qos_hide_latency_tolerance.
Fixes: 510a405d945b("nvme: fix memory leak for power latency tolerance")
Reported-by: Peng Liu <liupeng17@lenovo.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63ce8e3df8f6deca2da52eaf064751ad4018b46e upstream.
There are some omissions in the previous patch about replacing
I2C_MAX_FAST_MODE__FREQ with I2C_MAX_FAST_MODE_PLUS_FREQ and
need to fix it.
Fixes: b44658e755b5("i2c: mediatek: Send i2c master code at more than 1MHz")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2357dd9cbafc8ed37156e32c24884cfa8380b2f upstream.
When building with CONFIG_OF not set, the following clang
build warning is seen:
>> drivers/staging/media/rkvdec/rkvdec.c:967:34: warning: unused variable 'of_rkvdec_match' [-Wunused-const-variable]
Fix the warning by removing the unnecessary of_match_ptr().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: cd33c830448b ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34138a59b92c1a30649a18ec442d2e61f3bc34dd upstream.
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 402be8a101190969fc7ff122d07e262df86e132b upstream.
The retire logic uses the 2 lower bits of the pointer to the retire
function to store flags. However, the auto_retire function is not
guaranteed to be aligned to a multiple of 4, which causes crashes as
we jump to the wrong address, for example like this:
2021-04-24T18:03:53.804300Z WARNING kernel: [ 516.876901] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
2021-04-24T18:03:53.804310Z WARNING kernel: [ 516.876906] CPU: 7 PID: 146 Comm: kworker/u16:6 Tainted: G U 5.4.105-13595-g3cd84167b2df #1
2021-04-24T18:03:53.804311Z WARNING kernel: [ 516.876907] Hardware name: Google Volteer2/Volteer2, BIOS Google_Volteer2.13672.76.0 02/22/2021
2021-04-24T18:03:53.804312Z WARNING kernel: [ 516.876911] Workqueue: events_unbound active_work
2021-04-24T18:03:53.804313Z WARNING kernel: [ 516.876914] RIP: 0010:auto_retire+0x1/0x20
2021-04-24T18:03:53.804314Z WARNING kernel: [ 516.876916] Code: e8 01 f2 ff ff eb 02 31 db 48 89 d8 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 f0 ff 87 c8 00 00 00 0f 88 ab 47 4a 00 31 c0 5d c3 0f <1f> 44 00 00 55 48 89 e5 f0 ff 8f c8 00 00 00 0f 88 9a 47 4a 00 74
2021-04-24T18:03:53.804319Z WARNING kernel: [ 516.876918] RSP: 0018:ffff9b4d809fbe38 EFLAGS: 00010286
2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876919] RAX: 0000000000000007 RBX: ffff927915079600 RCX: 0000000000000007
2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876921] RDX: ffff9b4d809fbe40 RSI: 0000000000000286 RDI: ffff927915079600
2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876922] RBP: ffff9b4d809fbe68 R08: 8080808080808080 R09: fefefefefefefeff
2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876924] R10: 0000000000000010 R11: ffffffff92e44bd8 R12: ffff9279150796a0
2021-04-24T18:03:53.804322Z WARNING kernel: [ 516.876925] R13: ffff92791c368180 R14: ffff927915079640 R15: 000000001c867605
2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876926] FS: 0000000000000000(0000) GS:ffff92791ffc0000(0000) knlGS:0000000000000000
2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876928] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
2021-04-24T18:03:53.804324Z WARNING kernel: [ 516.876929] CR2: 0000239514955000 CR3: 00000007f82da001 CR4: 0000000000760ee0
2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876930] PKRU: 55555554
2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876931] Call Trace:
2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876935] __active_retire+0x77/0xcf
2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876939] process_one_work+0x1da/0x394
2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876941] worker_thread+0x216/0x375
2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876944] kthread+0x147/0x156
2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876946] ? pr_cont_work+0x58/0x58
2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876948] ? kthread_blkcg+0x2e/0x2e
2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876950] ret_from_fork+0x1f/0x40
2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876952] Modules linked in: cdc_mbim cdc_ncm cdc_wdm xt_cgroup rfcomm cmac algif_hash algif_skcipher af_alg xt_MASQUERADE uinput snd_soc_rt5682_sdw snd_soc_rt5682 snd_soc_max98373_sdw snd_soc_max98373 snd_soc_rl6231 regmap_sdw snd_soc_sof_sdw snd_soc_hdac_hdmi snd_soc_dmic snd_hda_codec_hdmi snd_sof_pci snd_sof_intel_hda_common intel_ipu6_psys snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence snd_sof_intel_hda snd_sof snd_soc_hdac_hda snd_soc_acpi_intel_match snd_soc_acpi snd_hda_ext_core soundwire_bus snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core intel_ipu6_isys videobuf2_dma_contig videobuf2_v4l2 videobuf2_common videobuf2_memops mei_hdcp intel_ipu6 ov2740 ov8856 at24 sx9310 dw9768 v4l2_fwnode cros_ec_typec intel_pmc_mux roles acpi_als typec fuse iio_trig_sysfs cros_ec_light_prox cros_ec_lid_angle cros_ec_sensors cros_ec_sensors_core industrialio_triggered_buffer cros_ec_sensors_ring kfifo_buf industrialio cros_ec_sensorhub
2021-04-24T18:03:53.804337Z WARNING kernel: [ 516.876972] cdc_ether usbnet iwlmvm lzo_rle lzo_compress iwl7000_mac80211 iwlwifi zram cfg80211 r8152 mii btusb btrtl btintel btbcm bluetooth ecdh_generic ecc joydev
2021-04-24T18:03:53.804337Z EMERG kernel: [ 516.879169] gsmi: Log Shutdown Reason 0x03
This change fixes this by aligning the function.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Fixes: 229007e02d69 ("drm/i915: Wrap i915_active in a simple kreffed struct")
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429031021.1218091-1-marcheu@chromium.org
(cherry picked from commit ca419f407b43cc89942ebc297c7a63d94abbcae4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a915fe5e9601c632417ef5261af70788d7d23a8a upstream.
__i915_active_call annotation is required on the retire callback to ensure
correct function alignment.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a21ce8ad12d2 ("drm/i915/overlay: Switch to using i915_active tracking")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429083530.849546-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit d8e44e4dd221ee283ea60a6fb87bca08807aa0ab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04d019961fd15de92874575536310243a0d4c5c5 upstream.
We've defined C0DRB3/C1DRB3 as 16 bit registers, so access them
as such.
Fixes: 1c8242c3a4b2 ("drm/i915: Use unchecked writes for setting up the fences")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210421153401.13847-3-ville.syrjala@linux.intel.com
(cherry picked from commit f765a5b48c667bdada5e49d5e0f23f8c0687b21b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea995218dddba171fecd05496c69617c5ef3c5b8 upstream.
Our code analyzer reported a double free bug.
In gen8_preallocate_top_level_pdp, pde and pde->pt.base are allocated
via alloc_pd(vm) with one reference. If pin_pt_dma() failed, pde->pt.base
is freed by i915_gem_object_put() with a reference dropped. Then free_pd
calls free_px() defined in intel_ppgtt.c, which calls i915_gem_object_put()
to put pde->pt.base again.
As pde->pt.base is protected by refcount, so the second put will not free
pde->pt.base actually. But, maybe it is better to remove the first put?
Fixes: 82adf901138cc ("drm/i915/gt: Shrink i915_page_directory's slab bucket")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210426124340.4238-1-lyl2019@mail.ustc.edu.cn
(cherry picked from commit ac69496fe65cca0611d5917b7d232730ff605bc7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 374157ff88ae1a7f7927331cbc72c1ec11994e8a upstream.
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a072022487 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25de4ce5ed02994aea8bc111d133308f6fd62566 upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3efe7a878a11c13b5297057bfc1e5639ce1241ce upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from dmtimer_clockevent_init().
This patch makes no intentional functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eea53c5816889ee8b64544fa2e9311a81184ff9c upstream.
When the first level page table is used for IOVA translation, it only
supports Read-Only and Read-Write permissions. The Write-Only permission
is not supported as the PRESENT bit (implying Read permission) should
always set. When using second level, we still give separate permissions
that allows WriteOnly which seems inconsistent and awkward. We want to
have consistent behavior. After moving to 1st level, we don't want things
to work sometimes, and break if we use 2nd level for the same mappings.
Hence remove this configuration.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8ce9ebbecdfda3322bbcece6b3b25888217f8e3 upstream.
The Access/Dirty bits in the first level page table entry will be set
whenever a page table entry was used for address translation or write
permission was successfully translated. This is always true when using
the first-level page table for kernel IOVA. Instead of wasting hardware
cycles to update the certain bits, it's better to set them up at the
beginning.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210115004202.953965-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 416fa531c8160151090206a51b829b9218b804d9 which is
commit a8ce9ebbecdfda3322bbcece6b3b25888217f8e3 upstream as it was
backported incorrectly and is causing problems for some systems.
Reported-by: Wolfgang Müller <wolf@oriole.systems>
Reported-by: Charles Wright <charles@charleswright.co>
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit c848416cc05afc1589edba04fe00b85c2f797ee3 which is
eea53c5816889ee8b64544fa2e9311a81184ff9c upstream.
Another iommu patch was backported incorrectly, causing problems, so
drop this as well for the moment.
Reported-by: Wolfgang Müller <wolf@oriole.systems>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 970655aa9b42461f8394e4457307005bdeee14d9 upstream.
Commit d3eeb1d77c5d0af ("xen/gntdev: use mmu_interval_notifier_insert")
introduced an error in gntdev_mmap(): in case the call of
mmu_interval_notifier_insert_locked() fails the exit path should not
call mmu_interval_notifier_remove(), as this might result in NULL
dereferences.
One reason for failure is e.g. a signal pending for the running
process.
Fixes: d3eeb1d77c5d0af ("xen/gntdev: use mmu_interval_notifier_insert")
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Luca Fancellu <luca.fancellu@arm.com>
Link: https://lore.kernel.org/r/20210423054038.26696-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18abf874367456540846319574864e6ff32752e2 upstream.
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210426092622.20433-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af0e1871d79cfbb91f732d2c6fa7558e45c31038 upstream.
The lux_val returned from tsl2583_get_lux can potentially be zero,
so check for this to avoid a division by zero and an overflowed
gain_trim_val.
Fixes clang scan-build warning:
drivers/iio/light/tsl2583.c:345:40: warning: Either the
condition 'lux_val<0' is redundant or there is division
by zero at line 345. [zerodivcond]
Fixes: ac4f6eee8fe8 ("staging: iio: TAOS tsl258x: Device driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f73c730774d88a14d7b60feee6d0e13570f99499 upstream.
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org
Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201
Reported-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c128781d8da463761495aaf8898c9ecb4e71528 upstream.
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dda32c00c9a0fa103b5d54ef72c477b7aa993679 upstream.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b813511135e8b84fa741afdfbab4937919100bef upstream.
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@vger.kernel.org
Signed-off-by: Abhijeet Rao <abhijeet.rao@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9a0866a5bdf6a4643a52872ada6be6184c6f4f2 upstream.
device_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210504222337.3151726-1-andy.shevchenko@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f4642b72be79757f050924a9b9673b6a02034bc upstream.
commit 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects
in PD mode") introduced retrieval of the PDOs when connected to a
PD-capable source. But only the first 4 PDOs are received since
that is the maximum number that can be fetched at a time given the
MESSAGE_IN length limitation (16 bytes). However, as per the PD spec
a connected source may advertise up to a maximum of 7 PDOs.
If such a source is connected it's possible the PPM could have
negotiated a power contract with one of the PDOs at index greater
than 4, and would be reflected in the request data object's (RDO)
object position field. This would result in an out-of-bounds access
when the rdo_index() is used to index into the src_pdos array in
ucsi_psy_get_voltage_now().
With the help of the UBSAN -fsanitize=array-bounds checker enabled
this exact issue is revealed when connecting to a PD source adapter
that advertise 5 PDOs and the PPM enters a contract having selected
the 5th one.
[ 151.545106][ T70] Unexpected kernel BRK exception at EL1
[ 151.545112][ T70] Internal error: BRK handler: f2005512 [#1] PREEMPT SMP
...
[ 151.545499][ T70] pc : ucsi_psy_get_prop+0x208/0x20c
[ 151.545507][ T70] lr : power_supply_show_property+0xc0/0x328
...
[ 151.545542][ T70] Call trace:
[ 151.545544][ T70] ucsi_psy_get_prop+0x208/0x20c
[ 151.545546][ T70] power_supply_uevent+0x1a4/0x2f0
[ 151.545550][ T70] dev_uevent+0x200/0x384
[ 151.545555][ T70] kobject_uevent_env+0x1d4/0x7e8
[ 151.545557][ T70] power_supply_changed_work+0x174/0x31c
[ 151.545562][ T70] process_one_work+0x244/0x6f0
[ 151.545564][ T70] worker_thread+0x3e0/0xa64
We can resolve this by instead retrieving and storing up to the
maximum of 7 PDOs in the con->src_pdos array. This would involve
two calls to the GET_PDOS command.
Fixes: 992a60ed0d5e ("usb: typec: ucsi: register with power_supply class")
Fixes: 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects in PD mode")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210503074611.30973-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18ffa988dbae69cc6e9949cddd9606f6fe533894 upstream.
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
Fixes: 8d99087c2db8 ("usb: dwc3: gadget: Properly handle failed kick_transfer")
cc: stable@vger.kernel.org
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1620410119-24971-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1d90dd27254c44d087ad3f8b5b3e4fff0571f45 upstream.
commit 72704f876f50 ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 975f94c7d6c306b833628baa9aec3f79db1eb3a1 upstream.
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
CC: <stable@vger.kernel.org>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210512020738.52961-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75a41ce46bae6cbe7d3bb2584eb844291d642874 upstream.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
