summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-06-11vhost: check owner before we overwrite ubuf_infoMichael S. Tsirkin
If device has an owner, we shouldn't touch ubuf_info since it might be in use. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-11qmi_wwan/cdc_ether: let qmi_wwan handle the Huawei E1820Bjørn Mork
Another QMI speaking Qualcomm based device, which should be driven by qmi_wwan, while cdc_ether should ignore it. Like on other Huawei devices, the wwan function can appear either as a single vendor specific interface or as a CDC ECM class function using separate control and data interfaces. The ECM control interface protocol is 0xff, likely in an attempt to indicate that vendor specific management is required. In addition to the near standard CDC class, Huawei also add vendor specific AT management commands to their firmwares. This is probably an attempt to support non-Windows systems using standard class drivers. Unfortunately, this part of the firmware is often buggy. Linux is much better off using whatever native vendor specific management protocol the device offers, and Windows uses, whenever possible. This means QMI in the case of Qualcomm based devices. The E1820 has been verified to work fine with QMI. Matching on interface number is necessary to distiguish the wwan function from serial functions in the single interface mode, as both function types will have class/subclass/function set to ff/ff/ff. The control interface number does not change in CDC ECM mode, so the interface number matching rule is sufficient to handle both modes. The cdc_ether blacklist entry is only relevant in CDC ECM mode, but using a similar interface number based rule helps document this as a transfer from one driver to another. Other Huawei 02/06/ff devices are left with the cdc_ether driver because we do not know whether they are based on Qualcomm chips. The Huawei specific AT command management is known to be somewhat hardware independent, and their usage of these class codes may also be independent of the modem hardware. Reported-by: Graham Inggs <graham.inggs@uct.ac.za> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-11sh_eth: fix result of sh_eth_check_reset() on timeoutSergei Shtylyov
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the following check for 'cnt < 0' fails to catch the timeout. Fix the condition in this check, so that the timeout is actually reported. While at it, fix the grammar in the failure message... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-11net/ti davinci_mdio: don't hold a spin lock while calling pm_runtimeSebastian Siewior
was playing with suspend and run into this: |BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891 |in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash |6 locks held by bash/1963: |CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50 |[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14) |[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac) |[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) |[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54) |[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) |[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c) |[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230) |[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350) |[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c) |[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc) |[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20) |[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c) |[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190) |[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70) |[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48) I don't see a reason why the pm_runtime call must be under the lock. Further I don't understand why this is a spinlock and not mutex. Cc: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-10tuntap: fix a possible race between queue selection and changing queuesJason Wang
Complier may generate codes that re-read the tun->numqueues during tun_select_queue(). This may be a race if vlan->numqueues were changed in the same time and can lead unexpected result (e.g. very huge value). We need prevent the compiler from generating such codes by adding an ACCESS_ONCE() to make sure tun->numqueues were only read once. Bug were introduced by commit c8d68e6be1c3b242f1c598595830890b65cea64a (tuntap: multiqueue support). Reported-by: Michael S. Tsirkin <mst@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-10vhost_net: clear msg.control for non-zerocopy case during txJason Wang
When we decide not use zero-copy, msg.control should be set to NULL otherwise macvtap/tap may set zerocopy callbacks which may decrease the kref of ubufs wrongly. Bug were introduced by commit cedb9bdce099206290a2bdd02ce47a7b253b6a84 (vhost-net: skip head management if no outstanding). This solves the following warnings: WARNING: at include/linux/kref.h:47 handle_tx+0x477/0x4b0 [vhost_net]() Modules linked in: vhost_net macvtap macvlan tun nfsd exportfs bridge stp llc openvswitch kvm_amd kvm bnx2 megaraid_sas [last unloaded: tun] CPU: 5 PID: 8670 Comm: vhost-8668 Not tainted 3.10.0-rc2+ #1566 Hardware name: Dell Inc. PowerEdge R715/00XHKG, BIOS 1.5.2 04/19/2011 ffffffffa0198323 ffff88007c9ebd08 ffffffff81796b73 ffff88007c9ebd48 ffffffff8103d66b 000000007b773e20 ffff8800779f0000 ffff8800779f43f0 ffff8800779f8418 000000000000015c 0000000000000062 ffff88007c9ebd58 Call Trace: [<ffffffff81796b73>] dump_stack+0x19/0x1e [<ffffffff8103d66b>] warn_slowpath_common+0x6b/0xa0 [<ffffffff8103d6b5>] warn_slowpath_null+0x15/0x20 [<ffffffffa0197627>] handle_tx+0x477/0x4b0 [vhost_net] [<ffffffffa0197690>] handle_tx_kick+0x10/0x20 [vhost_net] [<ffffffffa019541e>] vhost_worker+0xfe/0x1a0 [vhost_net] [<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net] [<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net] [<ffffffff81061f46>] kthread+0xc6/0xd0 [<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70 [<ffffffff817a1aec>] ret_from_fork+0x7c/0xb0 [<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70 Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-06Merge tag 'staging-3.10-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver fixes from Greg Kroah-Hartman: "Here are some staging and IIO driver fixes for the 3.10-rc5 release. All of them are tiny, and fix a number of reported issues (build and runtime)" Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> * tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: iio:inkern: Fix typo/bug in convert raw to processed. iio: frequency: ad4350: Fix bug / typo in mask inkern: iio_device_put after incorrect return/goto staging: alarm-dev: information leak in alarm_compat_ioctl() iio:callback buffer: free the scan_mask staging: alarm-dev: information leak in alarm_ioctl() drivers: staging: zcache: fix compile error staging: dwc2: fix value of dma_mask
2013-06-06Merge tag 'tty-3.10-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fixes from Greg Kroah-Hartman: "Here are some small bugfixes, and one revert, of serial driver issues that have been reported" * tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly" serial: samsung: enable clock before clearing pending interrupts during init serial/imx: disable hardware flow control at startup
2013-06-06Merge tag 'usb-3.10-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are a number of USB bugfixes and new device ids for the 3.10-rc5 tree. Nothing major here, a number of new device ids (and movement from the option to the zte_ev driver of a number of ids that we had previously gotten wrong, some xhci bugfixes, some usb-serial driver fixes that were recently found, some host controller fixes / reverts, and a variety of smaller other things" * tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (29 commits) USB: option,zte_ev: move most ZTE CDMA devices to zte_ev USB: option: blacklist network interface on Huawei E1820 USB: whiteheat: fix broken port configuration USB: serial: fix TIOCMIWAIT return value USB: mos7720: fix hardware flow control USB: keyspan: remove unused endpoint-array access USB: keyspan: fix bogus array index USB: zte_ev: fix broken open USB: serial: Add Option GTM681W to qcserial device table. USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device USB: EHCI: fix regression related to qh_refresh() usbfs: Increase arbitrary limit for USB 3 isopkt length USB: zte_ev: fix control-message timeouts USB: mos7720: fix message timeouts USB: iuu_phoenix: fix bulk-message timeout USB: ark3116: fix control-message timeout USB: mos7840: fix DMA to stack USB: mos7720: fix DMA to stack USB: visor: fix initialisation of Treo/Kyocera devices USB: serial: fix Treo/Kyocera interrrupt-in urb context ...
2013-06-06USB: option,zte_ev: move most ZTE CDMA devices to zte_evDan Williams
Per some ZTE Linux drivers I found for the AC2716, the following patch moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff that option does is not required with zte_ev, because it doesn't implement any of the send_setup hooks which the blacklist suppressed. I did not move the 2718 over because I could not find any ZTE Linux drivers for that device, nor even any Windows drivers. Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-06USB: option: blacklist network interface on Huawei E1820Bjørn Mork
The mode used by Windows for the Huawei E1820 will use the same ff/ff/ff class codes for both serial and network functions. Reported-by: Graham Inggs <graham.inggs@uct.ac.za> Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-06USB: whiteheat: fix broken port configurationJohan Hovold
When configuring the port (e.g. set_termios) the port minor number rather than the port number was used in the request (and they only coincide for minor number 0). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-05USB: serial: fix TIOCMIWAIT return valueJohan Hovold
Fix regression introduced by commit 143d9d9616 ("USB: serial: add tiocmiwait subdriver operation") which made the ioctl operation return ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT implementation is missing. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Fix timeouts with direct mode authentication in mac80211, from Stanislaw Gruszka. 2) Aggregation sessions can deadlock in ath9k, from Felix Fietkau. 3) Netfilter's xt_addrtype doesn't work with ipv6 due to route lookups creating undesirable cache entries, from Florian Westphal. 4) Fix netfilter's ipt_ULOG from generating non-NULL terminated strings. 5) Fix netdev transmit queue crashes in mac80211, from Johannes Berg. 6) Fix copy and paste error in 802.11 stack that broke reporting of 64-bit station tx statistics, from Felix Fietkau. 7) When qlge_probe fails, it leaks the netdev. Fix from Wei Yongjun. 8) SKB control block (where we store the IP options information, amongst other things) must be cleared properly otherwise ICMP sending can crash for IP tunnels. Fix from Eric Dumazet. 9) Verification of Energy Efficient Ether support was coded wrongly, the test was inversed. Fix from Giuseppe CAVALLARO. 10) TCP handles redirects improperly because the wrong flow key is used for the route lookup. From Michal Kubecek. 11) Don't interpret MSG_CMSG_COMPAT from userspace, fix from Andy Lutomirski. 12) The new AF_VSOCK was missing from the lockdep string table, fix from Federico Vaga. 13) be2net doesn't handle checksumming of IP fragments properly, from Somnath Kotur. 14) Fix several bugs in the device address list code that lead to crashes and other misbehaviors. From Jay Vosburgh. 15) Fix ipv6 segmentation handling of fragmented GRE tunnel traffic, from Pravin B Shalr. 16) Fix usage of stale policies in IPSEC layer, from Paul Moore. 17) Fix team driver dump of ports when there are a large number of them, from Jiri Pirko. 18) Fix softlockups in UDP ipv4 socket lookup causes by and error in the hlist_nulls_for_each_entry_rcu() macro. From Eric Dumazet. 19) Fix several regressions added by the high rate accuracy changes to the htb packet scheduler. From Eric Dumazet. 20) Fix DMA'ing onto the stack in esd_usb2 and peak_usb CAN drivers, from Olivier Sobrie and Marc Kleine-Budde. 21) Fix unremovable network devices due to missing route pointer installation in the per-device ipv6 address list entries. From Gao feng. 22) Apply the tg3 5719 DMA workaround on 5720 chips as well, otherwise we get stalls. From Nithin Sujir. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits) net_sched: htb: do not mix 1ns and 64ns time units net: fix sk_buff head without data area tg3: Add read dma workaround for 5720 net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANAR bnx2x: Fix bridged GSO for 57710/57711 chips net: fec: add fallback to random MAC address bnx2x: fix TCP offload for tunneling ipv4 over ipv6 ipv6: assign rt6_info to inet6_ifaddr in init_loopback net/mlx4_core: Keep VF assigned MAC in the PF admin table net/mlx4_en: Handle unassigned VF MAC address correctly net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is sufficiently initialized net/mlx4_en: Fix adaptive moderation cq update net: can: peak_usb: Do not do dma on the stack net: can: esd_usb2: Do not do dma on the stack net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type hardware. net_sched: restore "overhead xxx" handling net: force a reload of first item in hlist_nulls_for_each_entry_rcu hyperv: Fix vlan_proto setting in netvsc_recv_callback() team: fix port list dump for big number of ports list: introduce list_first_entry_or_null ...
2013-06-04tg3: Add read dma workaround for 5720Nithin Sujir
Commit 091f0ea30074bc43f9250961b3247af713024bc6 "tg3: Add New 5719 Read DMA workaround" added a workaround for TX DMA stall on the 5719. This workaround needs to be applied to the 5720 as well. Cc: stable@vger.kernel.org Reported-by: Roland Dreier <roland@purestorage.com> Tested-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANARJens Renner \(EFE\)
This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not setting them correctly on others (like TI DP83630) makes the PHY fall back to 10M HDX mode which should be avoided. Tested for TI DP83630 PHY on Microblaze platform. Signed-off-by: Jens Renner <renner@efe-gmbh.de> Tested-by: Michal Simek <monstr@monstr.eu> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04bnx2x: Fix bridged GSO for 57710/57711 chipsYuval Mintz
It was recently found out that GSO on 57710/57711 was broken, due to packets being sent without a valid IP checksum. Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this issue, but failed to set the correct IP checksum when receiving GSO packets via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed to calculate IP checksum were erroneously set in the incorrect buffer descriptor. This patch re-enables GSO in said scenario for 57710/57711 chips. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-05Merge tag 'mmc-fixes-for-3.10-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC fixes from Chris Ball: - sdhci-acpi: Fix initial runtime PM status, add more ACPI IDs - atmel-mci, omap_hsmmc: DT handling fixes - esdhc-imx: Fix SDIO IRQs, fix multiblock reads (both h/w errata) * tag 'mmc-fixes-for-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: mmc: omap_hsmmc: Skip platform_get_resource_byname() for dt case mmc: omap_hsmmc: convert to dma_request_slave_channel_compat mmc: omap_hsmmc: Fix the DT pbias workaround for MMC controllers 2 to 5 mmc: sdhci-pci: add more device ids mmc: sdhci-acpi: add more device ids mmc: sdhci-acpi: fix initial runtime pm status mmc: atmel-mci: convert to dma_request_slave_channel_compat() mmc: sdhci-esdhc-imx: fix multiblock reads on i.MX53 mmc: sdhci-esdhc-imx: Fix SDIO interrupts
2013-06-05Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: "Just a 2 small driver fixups here" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: wacom - fix a typo for Cintiq 22HDT Input: synaptics - fix sync lost after resume on some laptops
2013-06-04net: fec: add fallback to random MAC addressLucas Stach
If no valid MAC address could be obtained from the hardware, fall back to a randomly generated one. Signed-off-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04bnx2x: fix TCP offload for tunneling ipv4 over ipv6Dmitry Kravkov
FW was initialized with data from wrong header, this caused TSO packets have wrong IP csum. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04Merge branch 'fixes-for-3.10' of git://gitorious.org/linux-can/linux-canDavid S. Miller
Marc Kleine-Budde says: ==================== here are there fixes for the v3.10 release cycle: The first patch by Jonas Peterson and Olivier Sobrie fixes the reception of CAN frames on Kvaser's "USBcan Pro" and "USBcan R" type hardware. The last two patches by Olivier Sobrie (for esd_usb2) and me (for peak_usb) change the memory handling for the USB messages from stack to kmalloc(), as memory used for DMA should not be allocated on stack. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_core: Keep VF assigned MAC in the PF admin tableOr Gerlitz
MAC addresses assigned by the PF to VFs were not kept in the PF driver admin table. As a result, displaying the VF MACs from the PF interface to user space showed zero address where in fact the VF got non-zero address from the PF, fix that. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_en: Handle unassigned VF MAC address correctlyOr Gerlitz
When a VF sense they didn't get MAC address, use random one. This will address the case of administrator not assigning MAC to the VF through the PF OS APIs and keep udev happy. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is ↵Jack Morgenstein
sufficiently initialized In the PF initialization, SRIOV is enabled before the PF is fully initialized. This allows the kernel to probe the newly-exposed VFs before the PF is ready to handle them (nested probes). Have the probe method return the -EPROBE_DEFER value in this situation (instead of the VF probe method retrying its initialization in a loop, and returning -EIO on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel itself will retry the probe after a suitable delay. Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_en: Fix adaptive moderation cq updateSagi Grimberg
When turning on adaptive_rx under adaptive moderation, the CQ's moderation count wasn't updated according to rx_frames which resulted in too many interrupts and bandwidth drop. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04Merge tag 'iio-fixes-for-3.10b' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: Second round of IIO fixes for the 3.10 cycle. A couple of little bits and pieces, some delayed due to traveling. 1) A memory leak fix in the callback buffer. 2) Wrong exit path due to a return when it should have been a goto. 3) Bug in a mask value in ad4350 4) Reading the wrong value in raw to processed utility function.
2013-06-04iio:inkern: Fix typo/bug in convert raw to processed.Michael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-06-04iio: frequency: ad4350: Fix bug / typo in maskMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-06-04inkern: iio_device_put after incorrect return/gotoJoe Perches
The code uses return foo; goto err_type; when instead the form should have been ret = foo; goto err_type; Here this causes a useful iio_device_put to be skipped. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-06-04staging: alarm-dev: information leak in alarm_compat_ioctl()Dan Carpenter
If we pass an invalid clock type then "ts" is never set. We need to check for errors earlier, otherwise we end up passing uninitialized stack data to userspace. Reported-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-04iio:callback buffer: free the scan_maskJonathan Cameron
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-06-04USB: mos7720: fix hardware flow controlJohan Hovold
The register access to enable hardware flow control depends on the device port number and not the port minor number. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-04USB: keyspan: remove unused endpoint-array accessJohan Hovold
Remove the no longer used endpoint-array access completely. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-04USB: keyspan: fix bogus array indexJohan Hovold
The outcont_endpoints array was indexed using the port minor number (which can be greater than the array size) rather than the device port number. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-04USB: zte_ev: fix broken openJohan Hovold
Remove bogus port-number check in open and close, which prevented this driver from being used with a minor number different from zero. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-04Input: wacom - fix a typo for Cintiq 22HDTPing Cheng
And make the lines easier to read. Signed-off-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-06-04Input: synaptics - fix sync lost after resume on some laptopsEric Miao
In summary, the symptom is intermittent key events lost after resume on some machines with synaptics touchpad (seems this is synaptics _only_), and key events loss is due to serio port reconnect after psmouse sync lost. Removing psmouse and inserting it back during the suspend/resume process is able to work around the issue, so the difference between psmouse_connect() and psmouse_reconnect() is the key to the root cause of this problem. After comparing the two different paths, synaptics driver has its own implementation of synaptics_reconnect(), and the missing psmouse_probe() seems significant, the patch below added psmouse_probe() to the reconnect process, and has been verified many times that the issue could not be reliably reproduced. There are two PS/2 commands in psmouse_probe(): 1. PSMOUSE_CMD_GETID 2. PSMOUSE_CMD_RESET_DIS Only the PSMOUSE_CMD_GETID seems to be significant. The PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying several times. So we have only implemented this patch to issue the PSMOUSE_CMD_GETID so far. Tested-by: Daniel Manrique <daniel.manrique@canonical.com> Signed-off-by: James M Leddy <james.leddy@canonical.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-06-04Merge tag 'regulator-v3.10-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator Pull regulator fixes from Mark Brown: "A few small fixes for v3.10, documentation things in the core and a few driver bugs." * tag 'regulator-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: palmas: Fix "enable_reg" to point to the correct reg for SMPS10 regulator: palmas: Fix incorrect condition regulator: core: Correct spelling mistake in comment regulator: dbx500: Make local symbol static regulator: Fix kernel-doc generation warnings.
2013-06-03staging: alarm-dev: information leak in alarm_ioctl()Dan Carpenter
Smatch complains that if we pass an invalid clock type then "ts" is never set. We need to check for errors earlier, otherwise we end up passing uninitialized stack data to userspace. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03USB: serial: Add Option GTM681W to qcserial device table.Richard Weinberger
The Option GTM681W uses a qualcomm chip and can be served by the qcserial device driver. Signed-off-by: Richard Weinberger <richard@nod.at> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03USB: Serial: cypress_M8: Enable FRWD Dongle hidcom deviceRobert Butora
The patch adds a new HIDCOM device and does not affect other devices driven by the cypress_M8 module. Changes are: - add VendorID ProductID to device tables - skip unstable speed check because FRWD uses 115200bps - skip reset at probe which is an issue workaround for this particular device. Signed-off-by: Robert Butora <robert.butora.fi@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly"Kyle McMartin
This reverts commit cfcec52e9781f08948c6eb98198d65c45be75a70. This regresses a longstanding behaviour on X86 systems, which end up with PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite sides of this commit, resulting in the need to constantly modify the console setting in order to bisect across it. Please revert, we can work on solving this for ARM platforms in a less disruptive way. Signed-off-by: Kyle McMartin <kyle@mcmartin.ca> Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03serial: samsung: enable clock before clearing pending interrupts during initChander Kashyap
Ensure that the uart controller clock is enabled prior to writing to the interrupt mask and pending registers in the s3c24xx_serial_init_port function. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03serial/imx: disable hardware flow control at startupLucas Stach
We only want to enable hardware flow control if RTS/CTS pins are connected. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03net: can: peak_usb: Do not do dma on the stackMarc Kleine-Budde
smatch reports the following warnings: drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer) drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi) drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi) See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?" Cc: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03net: can: esd_usb2: Do not do dma on the stackOlivier Sobrie
smatch reports the following warnings: drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg) See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?" Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Cc: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type ↵Jonas Peterson
hardware. Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This patch adds support for it. Cc: linux-stable <stable@vger.kernel.org> # >= v3.8 Signed-off-by: Jonas Peterson <jonas.peterson@gmail.com> Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: "Recent bug fixes, one of them touches a common code file. It adds two #ifndef/#endif pairs to asm-generic/io.h to be able to override xlate_dev_kmem_ptr and xlate_dev_mem_ptr." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/pgtable: Fix gmap notifier address s390/dasd: fix handling of gone paths s390/pgtable: Fix check for pgste/storage key handling arch: s390: appldata: using strncpy() and strnlen() instead of sprintf() s390/smp: lost IPIs on cpu hotplug kernel: Fix s390 absolute memory access for /dev/mem s390/dma: do not call debug_dma after free
2013-06-03Merge branch 'for-3.10-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata changes from Tejun Heo: "Nothing too interesting. PCI ID additions, some sata_rcar fixes and a fringe bug fix for DMADIR handling which shouldn't affect any device remotely modern." * 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: sata_rcar: fix interrupt handling ahci: add an observed PCI ID for Marvell 88se9172 SATA controller sata_rcar: clear STOP bit in bmdma_start() method libata: make ata_exec_internal_sg honor DMADIR ata_piix: add PCI IDs for Intel BayTail libata: update "Maintained by:" tags
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-17 04:18:17 +0000